Management of Metals in the Pulping Process

Diplomityön tarkoituksena oli löytää keino korkean mangaanipitoisuuden hallintaan ECF-valkaisussa. Kirjallisuusosassa käsiteltiin eri metallien ja kuidun vuorovaikutuksia sekä niiden vaikutuksia prosessiin. Lisäksi käytiin läpi sellunvalmituksen yleisimpiä metallienhallintamenetelmiä. Työn kokeellisessa osassa tehtiin esikokeina laboratoriokokeita, jotta löydettiin oikeat kelatointistrategiat tehdasmittakaavan koeajoille. Laboratoriovalkaisut suoritettiin kuudella eri kemikaalilla käyttäen DD3-pesurin jälkeistä massaa ja samanlaisia parametrejä kuin tehdasvalkaisussa. Kolmesta eri valkaisusekvenssistä paras tulos saavutettiin D0-QEP-sekvenssillä. Tehdasmittakaavan koeajojen tavoitteena oli saavuttaa alle 1 mg/kg jäännösmangaanipitoisuus valkaistussa massassa ja korkeampi vaaleus EOP-vaiheessa pienemmällä klooridioksidin kulutuksella. Koeajoissa käytettiinDTPA:ta ja EDTA:ta kahdeksassa eri koepisteessä. Pienimpiin jäännöspitoisuuksiin päästiin koepisteissä, joissa kelatointiaine annosteltiin ennen valkaisun viimeistä pesuvaihetta tai sen jälkeen. Samanlaisia tuloksia saavutettiin koepisteissä, joissa kelatointiaine lisättiin suoraan EOP-vaiheeseen. Tällöin kelatointiaineen käyttö johti myös korkeampaan vaaleuteen EOP-vaiheessa pienemmällä kappakertoimella kuin referenssissä. Säästöt klooridioksidin kulutuksessa eivät olleet kuitenkaan tarpeeksi suuret kattaakseen kelatointiaineiden käytön kustannuksia. Kustannustehokkain tapa kontrolloida jäännösmangaanipitoisuutta oli EDTA:n annostelu D2 DD-pesurin jälkeen. Haittapuolena tälläisessä kelatoinnissa oli metallikompleksien palautuminen valkaisuun kuivauskoneen kiertoveden mukana. Tärkeimmät onnistuneeseen kelatointiin vaikuttavat parametrit olivat lajittelussa käytetyn rikkihapon annos, D0-vaiheen pH ja D0 DD-pesurin pesutehokkuus.

Hydrometallurgical recovery of valuable metals from secondary raw materials

Wastes and side streams in the mining industry and different anthropogenic wastes often contain valuable metals in such concentrations their recovery may be economically viable. These raw materials are collectively called secondary raw materials. The recovery of metals from these materials is also environmentally favorable, since many of the metals, for example heavy metals, are hazardous to the environment. This has been noticed in legislative bodies, and strict regulations for handling both mining and anthropogenic wastes have been developed, mainly in the last decade. In the mining and metallurgy industry, important secondary raw materials include, for example, steelmaking dusts (recoverable metals e.g. Zn and Mo), zinc plant residues (Ag, Au, Ga, Ge, In) and waste slurry from Bayer process alumina production (Ga, REE, Ti, V). From anthropogenic wastes, waste electrical and electronic equipment (WEEE), among them LCD screens and fluorescent lamps, are clearly the most important from a metals recovery point of view. Metals that are commonly recovered from WEEE include, for example, Ag, Au, Cu, Pd and Pt. In LCD screens indium, and in fluorescent lamps, REEs, are possible target metals. Hydrometallurgical processing routes are highly suitable for the treatment of complex and/or low grade raw materials, as secondary raw materials often are. These solid or liquid raw materials often contain large amounts of base metals, for example. Thus, in order to recover valuable metals, with small concentrations, highly selective separation methods, such as hydrometallurgical routes, are needed. In addition, hydrometallurgical processes are also seen as more environmental friendly, and they have lower energy consumption, when compared to pyrometallurgical processes. In this thesis, solvent extraction and ion exchange are the most important hydrometallurgical separation methods studied. Solvent extraction is a mainstream unit operation in the metallurgical industry for all kinds of metals, but for ion exchange, practical applications are not as widespread. However, ion exchange is known to be particularly suitable for dilute feed solutions and complex separation tasks, which makes it a viable option, especially for processing secondary raw materials. Recovering valuable metals was studied with five different raw materials, which included liquid and solid side streams from metallurgical industries and WEEE. Recovery of high purity (99.7%) In, from LCD screens, was achieved by leaching with H2SO4, extracting In and Sn to D2EHPA, and selectively stripping In to HCl. In was also concentrated in the solvent extraction stage from 44 mg/L to 6.5 g/L. Ge was recovered as a side product from two different base metal process liquors with Nmethylglucamine functional chelating ion exchange resin (IRA-743). Based on equilibrium and dynamic modeling, a mechanism for this moderately complex adsorption process was suggested. Eu and Y were leached with high yields (91 and 83%) by 2 M H2SO4 from a fluorescent lamp precipitate of waste treatment plant. The waste also contained significant amounts of other REEs such as Gd and Tb, but these were not leached with common mineral acids in ambient conditions. Zn was selectively leached over Fe from steelmaking dusts with a controlled acidic leaching method, in which the pH did not go below, but was held close as possible to, 3. Mo was also present in the other studied dust, and was leached with pure water more effectively than with the acidic methods. Good yield and selectivity in the solvent extraction of Zn was achieved by D2EHPA. However, Fe needs to be eliminated in advance, either by the controlled leaching method or, for example, by precipitation. 100% Pure Mo/Cr product was achieved with quaternary ammonium salt (Aliquat 336) directly from the water leachate, without pH adjustment (pH 13.7). A Mo/Cr mixture was also obtained from H2SO4 leachates with hydroxyoxime LIX 84-I and trioctylamine (TOA), but the purities were 70% at most. However with Aliquat 336, again an over 99% pure mixture was obtained. High selectivity for Mo over Cr was not achieved with any of the studied reagents. Ag-NaCl solution was purified from divalent impurity metals by aminomethylphosphonium functional Lewatit TP-260 ion exchange resin. A novel preconditioning method, named controlled partial neutralization, with conjugate bases of weak organic acids, was used to control the pH in the column to avoid capacity losses or precipitations. Counter-current SMB was shown to be a better process configuration than either batch column operation or the cross-current operation conventionally used in the metallurgical industry. The raw materials used in this thesis were also evaluated from an economic point of view, and the precipitate from a waste fluorescent lamp treatment process was clearly shown to be the most promising.

Laser Cutting of Austenitic Stainless Steel with a High Quality Laser Beam

The thin disk and fiber lasers are new solid-state laser technologies that offer a combinationof high beam quality and a wavelength that is easily absorbed by metal surfacesand are expected to challenge the CO2 and Nd:YAG lasers in cutting of metals ofthick sections (thickness greater than 2mm). This thesis studied the potential of the disk and fiber lasers for cutting applications and the benefits of their better beam quality. The literature review covered the principles of the disk laser, high power fiber laser, CO2 laser and Nd:YAG laser as well as the principle of laser cutting. The cutting experiments were made with thedisk, fiber and CO2 lasers using nitrogen as an assist gas. The test material was austenitic stainless steel of sheet thickness 1.3mm, 2.3mm, 4.3mm and 6.2mm for the disk and fiber laser cutting experiments and sheet thickness of 1.3mm, 1.85mm, 4.4mm and 6.4mm for the CO2 laser cutting experiments. The experiments focused on the maximum cutting speeds with appropriate cut quality. Kerf width, cutedge perpendicularity and surface roughness were the cut characteristics used to analyze the cut quality. Attempts were made to draw conclusions on the influence of high beam quality on the cutting speed and cut quality. The cutting speeds were enormous for the disk and fiber laser cutting experiments with the 1.3mm and 2.3mm sheet thickness and the cut quality was good. The disk and fiber laser cutting speeds were lower at 4.3mm and 6.2mm sheet thickness but there was still a considerable percentage increase in cutting speeds compared to the CO2 laser cutting speeds at similar sheet thickness. However, the cut quality for 6.2mm thickness was not very good for the disk and fiber laser cutting experiments but could probably be improved by proper selection of cutting parameters.

Magnetic and transport properties of InGaAs quantum wells with Mn

In the present work structural, magnetic and transport properties of InGaAs quantum wells (QW) prepared by MBE with an remote Mn layer are investigated. By means of high-resolution X-ray diffractometry the structure of the samples is analyzed. It is shown that Mn ions penetrate into the QW. Influence of the thickness of GaAs spacer and annealing at 286 ºС on the properties of the system is shown. It is shown that annealing of the samples led to Mn activation and narrowing of the Mn layer. Substantial role of 2D holes in ferromagnetic ordering in Mn layer is shown. Evidence for that is observation of maximum at 25 – 55 K on the resistivity temperature dependence. Position of maximum, which is used for quantitative assessment of the Curie temperature, correlates with calculations of the Curie temperature for structures with indirect interaction via 2D holes’ channel. Dependence of the Curie temperature on the spacer thickness shows, that creation of applicable spintronic devices needs high-precision equipment to manufacture extra fine structures. The magnetotransport measurements show that charge carrier mobility is very low. This leads to deficiency of the anomalous Hall effect. At the same time, magnetic field dependences of the magnetization at different temperatures demonstrate that systems are ferromagnetically ordered. These facts, most probably, give evidence of presence of the ferromagnetic MnAs clusters.

Commodity Price Driven Risk Management from Viewpoint of High Grade Steel Alloys

The study of price risk management concerning high grade steel alloys and their components was conducted. This study was focused in metal commodities, of which nickel, chrome and molybdenum were in a central role. Also possible hedging instruments and strategies for referred metals were studied. In the literature part main themes are price formation of Ni, Cr and Mo, the functioning of metal exchanges and main hedging instruments for metal commodities. This section also covers how micro and macro variables may affect metal prices from the viewpoint of short as well as longer time period. The experimental part consists of three sections. In the first part, multiple regression model with seven explanatory variables was constructed to describe price behavior of nickel. Results were compared after this with information created with comparable simple regression model. Additionally, long time mean price reversion of nickel was studied. In the second part, theoretical price of CF8M alloy was studied by using nickel, ferro-chrome and ferro-molybdenum as explanatory variables. In the last section, cross hedging possibilities for illiquid FeCr -metal was studied with five LME futures. Also this section covers new information concerning possible forthcoming molybdenum future contracts as well. The results of this study confirm, that linear regression models which are based on the assumption of market rationality, are not able to reliably describe price development of metals at issue. Models fulfilling assumptions for linear regression may though include useful information of statistical significant variables which have effect on metal prices. According to the experimental part, short futures were found to incorporate the most accurate information concerning the price movements in the future. However, not even 3M futures were able to predict turning point in the market before the faced slump. Cross hedging seemed to be very doubtful risk management strategy for illiquid metals, because correlations coefficients were found to be very sensitive for the chosen time span.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Electrocoagulation in the treatment of industrial waters and wastewaters

Chemical coagulation is commonly used in raw water and wastewater treatment plants for the destabilisation of pollutants so that they can be removed in the subsequent separation processes. The most commonly used coagulation chemicals are aluminium and iron metal salts. Electrocoagulation technology has also been proposed for the treatment of raw waters and wastewaters. With this technology, metal cations are produced on the electrodes via electrolysis and these cations form various hydroxides in the water depending on the water pH. In addition to this main reaction, several side reactions, such as hydrogen bubble formation and the reduction of metals on cathodes, also take place in the cell. In this research, the applications of electrocoagulation were investigated in raw water treatment and wastewater applications. The surface water used in this research contained high concentrations of natural organic matter (NOM). The effect of the main parameters – current density, initial pH, electric charge per volume, temperature and electrolysis cell construction – on NOM removal were investigated. In the wastewater treatment studies, the removal of malodorous sulphides and toxic compounds from the wastewaters and debarking effluents were studied. Also, the main parameters of the treatment, such as initial pH and current density, were investigated. Aluminium electrodes were selected for the raw water treatment, whereas wastewaters and debarking effluent were treated with iron electrodes. According to results of this study, aluminium is more suitable electrode material for electrocoagulation applications because it produces Al(III) species. Metal ions and hydroxides produced by iron electrodes are less effective in the destabilisation of pollutants because iron electrodes produce more soluble and less charged Fe(II) species. However, Fe(II) can be effective in some special applications, such as sulphide removal. The resulting metal concentration is the main parameter affecting destabilisation of pollutants. Current density, treatment time, temperature and electrolysis cell construction affect the dissolution of electrodes and hence also the removal of pollutants. However, it seems that these parameters have minimal significance in the destabilization of the pollutants besides this effect (in the studied range of parameters). Initial pH and final pH have an effect on the dissolution of electrodes, but they also define what aluminium or iron species are formed in the solution and have an effect on the ζ-potential of all charged species in the solution. According to the results of this study, destabilisation mechanisms of pollutants by electrocoagulation and chemical coagulation are similar. Optimum DOC removal and low residual aluminium can be obtained simultaneously with electrocoagulation, which may be a significant benefit of electrocoagulation in surface water treatment compared to chemical coagulation. Surface water treatment with electrocoagulation can produce high quality water, which could be used as potable water or fresh water for industrial applications. In wastewater treatment applications, electrocoagulation can be used to precipitate malodorous sulphides to prevent their release into air. Technology seems to be able to remove some toxic pollutants from wastewater and could be used as pretreatment prior to treatment at a biological wastewater treatment plant. However, a thorough economic and ecological comparison of chemical coagulation and electrocoagulation is recommended, because these methods seem to be similar in pollutant destabilisation mechanisms, metal consumption and removal efficiency in most applications.

Computational modeling of stented coronary arteries

The application of computational fluid dynamics (CFD) and finite element analysis (FEA) has been growing rapidly in the various fields of science and technology. One of the areas of interest is in biomedical engineering. The altered hemodynamics inside the blood vessels plays a key role in the development of the arterial disease called atherosclerosis, which is the major cause of human death worldwide. Atherosclerosis is often treated with the stenting procedure to restore the normal blood flow. A stent is a tubular, flexible structure, usually made of metals, which is driven and expanded in the blocked arteries. Despite the success rate of the stenting procedure, it is often associated with the restenosis (re-narrowing of the artery) process. The presence of non-biological device in the artery causes inflammation or re-growth of atherosclerotic lesions in the treated vessels. Several factors including the design of stents, type of stent expansion, expansion pressure, morphology and composition of vessel wall influence the restenosis process. Therefore, the role of computational studies is crucial in the investigation and optimisation of the factors that influence post-stenting complications. This thesis focuses on the stent-vessel wall interactions followed by the blood flow in the post-stenting stage of stenosed human coronary artery. Hemodynamic and mechanical stresses were analysed in three separate stent-plaque-artery models. Plaque was modeled as a multi-layer (fibrous cap (FC), necrotic core (NC), and fibrosis (F)) and the arterial wall as a single layer domain. CFD/FEA simulations were performed using commercial software packages in several models mimicking the various stages and morphologies of atherosclerosis. The tissue prolapse (TP) of stented vessel wall, the distribution of von Mises stress (VMS) inside various layers of vessel wall, and the wall shear stress (WSS) along the luminal surface of the deformed vessel wall were measured and evaluated. The results revealed the role of the stenosis size, thickness of each layer of atherosclerotic wall, thickness of stent strut, pressure applied for stenosis expansion, and the flow condition in the distribution of stresses. The thicknesses of FC, and NC and the total thickness of plaque are critical in controlling the stresses inside the tissue. A small change in morphology of artery wall can significantly affect the distribution of stresses. In particular, FC is the most sensitive layer to TP and stresses, which could determine plaque’s vulnerability to rupture. The WSS is highly influenced by the deflection of artery, which in turn is dependent on the structural composition of arterial wall layers. Together with the stenosis size, their roles could play a decisive role in controlling the low values of WSS (<0.5 Pa) prone to restenosis. Moreover, the time dependent flow altered the percentage of luminal area with WSS values less than 0.5 Pa at different time instants. The non- Newtonian viscosity model of the blood properties significantly affects the prediction of WSS magnitude. The outcomes of this investigation will help to better understand the roles of the individual layers of atherosclerotic vessels and their risk to provoke restenosis at the post-stenting stage. As a consequence, the implementation of such an approach to assess the post-stented stresses will assist the engineers and clinicians in optimizing the stenting techniques to minimize the occurrence of restenosis.

Characterization of design of a product for additive manufacturing

The purpose of conducting this thesis is to gather around information about additive manufacturing and to design a product to be additively manufactured. The specific manufacturing method dealt with in this thesis, is powder bed fusion of metals. Therefore when mentioning additive manufacturing in this thesis, it is referred to powder bed fusion of metals. The literature review focuses on the principle of powder bed fusion, the general process chain in additive manufacturing, design rules for additive manufacturing. Examples of success stories in additive manufacturing and reasons for selecting parts to be manufactured with additive manufacturing are also explained in literature review. This knowledge is demanded to understand the experimental part of the thesis. The experimental part of the thesis is divided into two parts. Part A concentrates on finding proper geometry for building self-supporting pipes and proper parameters for support structures of them. Part B of the experimental part concentrates on a case study of designing a product for additive manufacturing. As a result of experimental part A, the design process of self-supporting pipes, results of visual analysis and results of 3D scanning are presented. As a result of experimental part B the design process of the product is presented and compared to the original model.

Gold recovery from cyanideand chloride solution using activated carbon

Uusia keinoja kullan erottamiseksi malmista on etsitty viimeaikoina taloudellisista ja ympäristöllisistä syistä kautta maailman. Syanidointimenetelmä on hallinnut kullan talteenottoayli sata vuotta. Menetelmässä kulta liuotetaan laimeaan syanidiliuokseen, jostase otetaan talteen aktiivihiilen avulla. Syanidin käyttöä pyritään kuitenkin vähentämään sen myrkyllisyyden takia. Lisäksi nykyään louhitaan enenemässä määrin malmia, josta on hankala rikastaa kulta kustannustehokkaasti syanidia käyttäen. Kullan talteenottoa syanidi- ja kloridiliuoksesta on selvitetty kirjallisuuden avulla. Kullan kemiaan liuotuksen aikana on perehdytty ennen kullan talteenottoa aktiivihiilellä. Aktiivihiilen elinkaari kullan adsorbenttinaon käsitelty valmistuksesta hylkäämiseen mukaan lukien hiilen myrkyttyminen prosessissa ja regenerointi. Aktiivi-hiilen käyttäytyminen syanidi- ja kloridiliuoksessa on selvitetty erikseen. Kullan talteenottoa kuparipitoisista malmeista on käsitelty. Kullan talteenottoa kloridiliuoksesta aktiivihiiltä käyttäen on tutkittu kokeellisesti. Pääasialliset tutkimuskohteet ovat adsorption kinetiikka, kuparin vaikutus adsorptioon, aktiivihiilen vaikutus adsorptioonja adsorboituneiden metallien strippaus hiilestä selektiivisesti. Hapettavan stippauksen vaikutus kullan desorptioon hiilestä on tutkittu yksityiskohtaisesti. Kullan erotusmenetelmät kuparimalmista aktiivihiiltä käyttäen on selvitetty diplomityön tulosten pohjalta. Diplomityön keskeisten tulosten perusteella kulta ei välttämättä saostu aktiivihiilen pinnalle kloridiliuoksesta. Havainto varmistettiin ladattujen hiilipartikkelien pyyhkäisyelektronimikroskooppikuvista ja partikkeleille tehdyistä mikroanalyyseistä. Kullan pelkistyminen metalliseksi kullaksi aktiivihiilessä voitaneen välttää käyttämällä erittäin hapettavia olosuhteita. Aktiivihiili ilmeisesti hapettuu näissä olosuhteissa, mikä mahdollistaa kultakloridin adsorboitumisen hiileen.

Vesi-metanolitislauskolonnin ikääntyminen ja siihen vaikuttavat tekijät

Tässä työssä tutkittiin Fortum Oyj:n MTBE -yksikön vesi metanolitislauskolonnin käyttö- ja tarkastushistoriaa sekä yleisestä syöpymisestä aiheutunutta seinämän ohenemaa. Oheneminen oli kiihtynyt viimeisten käyttövuosien aikana. Kolonni poistettiin käytöstä vuonna 2002. Kirjallisuusosassa käsitellään MTBE -prosessia, metallien korroosiota eri olosuhteissa sekä korroosiotutkimusmenetelmiä. Eri korroosiotutkimusmenetelmistä käsitellään sähkökemiallinen kohina -menetelmää, vastuslankamittausta sekä upotuskokeita. Kokeellisessa osassa käsitellään tuloksia käyttö- ja tarkastushistoriaselvityksistä ja korroosiokokeista, jotka tehtiin kirjallisuusosassa esitettyjen menetelmien mukaisesti. Koekappaleet olivat hiiliterästä, joka oli vastaavaa materiaalia kuin metanolin tislauskolonni. Korroosiokokeiden tuloksista havaittiin, että hiiliteräs syöpyy nopeammin vesimetanoliliuoksessa, jossa on 60 - 80 metanolia. Syöpymisnopeus kasvoi liuoksen pH:n laskiessa ja oli suurinta kun pH oli alle 4,0.

Sulfaattimassan D/Q(EOP)D-valkaisimon optimointi

Työssä tutkittiin sulfaattisellutehtaan ECF-valkaisimon toimintaan vaikuttavia tekijöitä. Tavoitteena oli selvittää tekijöiden vaikutus massan laatuominaisuuksiin, valkaisimon kemikaalikustannuksiin ja klooridioksidin kulutukseen. Työn kirjallisuusosassa on tarkasteltu nykyaikaisen sulfaattisellutehtaan eri prosesseja. Erityistä huomiota on kiinnitetty sellun ECF-valkaisuun ja kyseisessä valkaisussa käytettäviin kemikaaleihin. Lisäksi on tarkasteltu TCF-valkaisua ja mahdollisuuksia sulkea sellutehtaan vesikiertoja. Kokeellisessa osassa selvitettiin Oy Metsä-Botnia Ab Joutsenon tehtaan kolmivaiheisen ECF-valkaisimon massan laatuominaisuuksiin, kustannuksiin ja klooridioksidin kulutukseen vaikuttavia tekijöitä. Tavoitteena oli vaikuttaa positiivisesti massan laatuominaisuuksiin valkaisun keinoin. Samalla pyrittiin minimoimaan valkaisusta aiheutuvia kemikaalikustannuksia ja vähentämään klooridioksidin kulutusta. Työssä käytettiin Taguchi-menetelmää. Tehdyn tutkimuksen myötä saatiin runsaasti tietoa mihin eri ominaisuuksiin tutkitut tekijät vaikuttivat. Metallien poistolla eli kelatoinnilla havaittiin olevan suuri merkitys hapettavan alkaliuuttovaiheen ja samalla koko valkaisimon toimintaan. Suurella kelatointiaineannoksella valkaisimon selektiivisyys ja tehokkuus paranivat. Muista tekijöistä happiannoksella havaittiin olevan vaikutusta vain massan paperiteknisiin ominaisuuksiin ja hiilihydraattien koostumukseen. Happiannoksen kasvattaminen paransi repäisyindeksiä ja vähensi massan jauhatustarvetta yli valkaisimon. Kyseisiin ominaisuuksiin vaikuttivat myös klooridioksidi ja sen toimintaolosuhteet. Kemikaalikustannuksiin vaikuttavista tekijöistä valkaisimon tulokapalla ja ensimmäisen klooridioksidivaiheen kemikaaliannoksella havaittiin olevan suuri merkitys. Samat tekijät vaikuttivat myös valkaisimon klooridioksidin kokonaiskulukseen.

TCF-valkaisimon laatuvaihtelun pienentäminen

Tämän diplomityön tavoitteena oli pienentää TCF-valkaisimon laatuvaihtelua ja vähentää kemikaaleista aiheutuvia kustannuksia. Työn kirjallisuusosassa tarkasteltiin valkaisuun vaikuttavia tekijöitä. Valkaisukemikaaleista olivat mukana TCF-valkaisussa käytettävät otsoni ja vetyperoksidi. Lisäksi selvitettiin metallien poistoa massasta sekä vesikierron sulkemisesta aiheutuvia ongelmia. Kokeellisessa osassa etsittiin Oy Metsä-Botnia Ab Rauman tehtaan valkaisuprosessin suurimmat laatuominaisuuksien vaihteluun vaikuttavat tekijät. Tavoitteena oli pienentää vaihtelua valmiin massan laatuominaisuuksissa sekä vähentää raaka-aineista ja kemikaaleista aiheutuvia kustannuksia laatuominaisuuksien tasoa laskematta. Tutkimuksessa käytettiin hyväksi Taguchi-menetelmää sekä monimuuttuja-analyysiä. Tutkimuksessa tehtiin kaksi Taguchi-koetta, joissa tutkittiin valkaisimon ensimmäistä otsonivaihetta sekä koko valkaisimoa. Otsonivaiheen merkittävimmiksi tekijöiksi osoittautuivat otsoniannos, otsonin väkevyys sekä pH. Kaikkia valkaisimon vaiheita tutkittaessa löydettiin merkittävimmiksi tekijöiksi ensimmäisen peroksidivaiheen lämpötila, vetyperoksidin jakaminen peroksidivaiheisiin, kelatointi sekä otsonivaiheen otsoniannos ja pH. Optimiajomallin avulla saatiin valkaisimon laatuvaihtelua pienennettyä. Kemikaalikustannuksiin vaikuttavista tekijöistä merkittävimmiksi osoittautuivat kelatoinnin vaikutus, vetyperoksidin annosteleminen molempiin vaiheisiin sekä ensimmäisen peroksidivaiheen lämpötila. Optimiajomallien avulla vetyperoksidikulutusta saatiin pienennettyä noin 24 %.

Häiriöaineiden vaikutus käytettäessä magnesiumhydroksidialkalia mekaanisen massan peroksidivalkaisussa

Nykypäivänä ympäristön suojelu ja erityisesti jätevesipäästöjen pienentäminen vaikuttavat yhä enemmän metsäteollisuuden toimintatapoihin. Lisäksi veden käytön vähentyessä ja prosesseja suljettaessa silikaatteihin väistämättä liittyvät saostumat ovat kasvava ongelma. Magnesiumhydroksidin on havaittu olevan potentiaalinen natriumhydroksidin korvaava alkali mekaanisen massan peroksidivalkaisussa. Lisäksi magnesiumhydroksidilla voidaan saavuttaa lähes yhtä korkea vaaleus, jopa ilman silikaattia, kuin natriumhydroksidilla natriumsilikaatin kanssa. Magnesiumhydroksidin orgaanista ainesta liuottava vaikutus on myös noin puolet verrattuna natriumhydroksidiin. Työssä selvitettiin, miten häiriöaineet vaikuttavat mekaanisen massan peroksidivalkaisuun käytettäessä magnesiumhydroksidialkalia. Laboratoriokokeiden tulokset osoittivat, että magnesiumhydroksidi kesti paremmin valkaisussa käytettyjä häiriöaineita. Pienillä metallilisäyksillä ei ole vaikutusta massan vaaleuteen käytettäessä magnesiumhydroksidia. Korvattaessa laimennusvettä viirapuristimen suodoksella peroksidi kului lähes loppuun käytettäessä natriumhydroksidia, mikä näkyi myös vaaleuden heikkenemisenä. Valkaisukokeiden perusteella magnesiumhydroksidialkalilla jäädään jopa kolme prosenttiyksikköä natriumhydroksidin kanssa saadusta vaaleudesta, peroksidiannoksen olleessa kolme prosenttia. Mutta käytettäessä magnesiumhydroksidialkalia liuenneen orgaanisen hiilen kokonaismäärä (TOC) sekä biologinen (BOD7) että kemiallinen (CODcr) hapenkulutus pienenivät lähes puolella.