Study of the influence of grain size and precipitates on the electromagnetic losses in different grades of non-oriented fully processed electrical steel

The study was performed in the installations of OCAS, a Steel Research Centre of ArcelorMittal. Taking M32 steel (3.25%Si+0.9%Al) as the basis chemical composition and three different thicknesses (0.35, 0.5 and 0.65mm), different annealing conditions (temperature and time) have been applied in the laboratory simulator at St. Chély, France. The aim was to link annealing parameters, grain size and energy loss. It was determined the optimum annealing parameters to reach the lowest power losses for three different grades of non-oriented fully processed electrical steel. In addition, M250-50 samples having different magnetic behaviour (high and low losses) but the same grain size and texture, have been analyzed in terms of TEM observations of their precipitates, in the University of Marseille. The results reveal that a high amount of medium and big precipitates (&10 nm) worsen the magnetic properties of the material. The small precipitates (&10nm) do not have a strong influence on the magnetic properties. The presence of precipitates can have a great influence on the power losses and further work is clearly necessary.

Link between microstructure and properties in new metallurgical concepts for very low loss non-oriented electrical steel

The influence of chemistry and soaking temperature (maximal temperature of the continuous annealing) on the final properties of non-oriented electrical steels has been studied. With this objective two different studies have been performed. First the Mn, Ni and Cr content of a low loss electrical steel composition has been modified. An intermediate content and a high content of each element has been added in order to study the influence of this components on the magnetic looses, grain size and texture. Secondly the influence of the soaking temperature on magnetic properties, grain size and oxidation in four grades of non-oriented electrical steels (Steel A, B, C and D) was studied.

Estudio del bypass gástrico en Y de Roux y de la gastrectomía tubular sobre el metabolismo de la glucosa y la secreción de hormonas intestinales. Estudio prospectivo y randomizado

Introducció: El bypass gàstric en Y de Roux laparoscòpic (BGYRL) és la tècnica quirúrgica d’elecció per al tractament de l’obesitat mòrbida. La gastrectomia tubular laparoscòpica (GTL) és una tècnica bariàtrica restrictiva amb resultats molt prometedors en relació a la pèrdua de pes, però se’n desconeixen els efectes metabòlics i endocrins. L’objectiu d’aquest estudi és l’avaluació de les diferències en la resposta del metabolisme de la glucosa i la secreció d’hormones intestinals entre ambdós procediments. Material i mètodes: Es va dissenyar un estudi prospectiu i aleatoritzat per la realització del BGYRL i la GTL, ambdós realitzats via laparoscòpica. Totes les pacients es varen avaluar abans, i als 3 i 12 mesos de la intervenció. Se’ls va prendre una mostra de sang venosa després d’un dejuni de 12 hores i als 10 i 60 minuts després de la ingesta d’Ensure® 420 kcal per realitzar les determinacions dels nivells plasmàtics de glucosa, insulina, grelina, leptina, pèptid relacionat amb glucagó (GLP-1), pèptid YY (PYY) i polipèptid pancreàtic (PP). Resultats: Es varen incloure 15 pacients (totes de gènere femení, edat mitja de 48±9 anys, IMC de 44±2.7 kg/m2 amlitat preoperatòria) dels quals 7 van ser aleatoritzats a BGYRL i 8 a GTL. No hi van haver diferències entre ambdós grups en edat, IMC preoperatori, classificació ASA i determinacions hormonals preoperatòries. Després de la cirurgia, s’observa un descens de la glicèmia i insulinèmia, amb una reducció de l´índex HOMA-IR en ambdós grups. Postoperatòriament, es detecta una disminución de les concentracions de la leptina en dejú i després de la ingesta, significativament menor en el grup de BGYRL. Mentre que els nivells de grelina en dejú només descendeixen de forma significativa en el grup de la GTL. Després de la ingesta es produeix una augment dels nivells de GLP-1, significativament major en el grup de BGYRL. Conclusions: Tan el BGYRL como la GTL s’associen a una significativa pèrdua de pes, encara que aquesta fou significativament superior en el BGYRL. Ambdós procediments han millorat notablement l’homeostasi de la glucosa. Només la GTL va rehuir els nivells de grelina tan en dejú com després de la ingesta, mentre que els nivells de GLP-1 i PYY s’elevaren després de la cirurgia, sense diferències estadísticament significatives entre ambdues tècniques.

Estudio prospectivo comparando la gastrectomía tubular laparoscópica y la gastrectomía robótica para el tratamiento de la obesidad mórbida

La cirurgia de l’obesitat suposa una eina dins de l’arsenal terapèutic dels pacients afectes d’obesitat mòrbida. La gastrectomia vertical s’ha popularitzat com a tècnica i les noves tecnologies com la laparoscòpia s’utilitzen de forma habitual. Més recentment la robòtica s’utilitza en diferents àmbits i també s’està implementant en la cirurgia de l’obesitat. A fi de compara la gastrectomia vertical realitzada mitjançant laparoscòpia o robòtica es planteja el següent estudi. S’han comparat els pacients intervinguts de gastrectomia vertical laparoscòpica i robòtica en termes de complicacions intraoperatòries, morbimortalitat i resultats en el seguiment dels pacients. Els resultats són satisfactoris en el sentit que es demostra que la tecnologia robòtica aporta els mateixos resultats en termes de complicacions intra y perioperatòries. Tanmateix es demostra que l’evolució ponderal dels pacients intervinguts de gastrectomia vertical amb tecnologia robòtica es igual a aquells intervinguts de manera tradicional. Així, es conclou que la tecnologia robòtica es una eina en ple desenvolupament que ha demostrat ser eficient, segura y eficaç per al tractament de la Obesitat Mòrbida mitjançant la Gastrectomia vertical.

Decentralized model reference control of flexible cable-stayed beam structures

A decentralized model reference controller is designed to reduce the magnitude of the transversal vibration of a flexible cable-stayed beam structure induced by a seismic excitation. The controller design is made based on the principle of sliding mode such that a priori knowledge

Statistical analysis and modelling of weather radar beam propagation conditions in the Po Valley (Italy)

Ground clutter caused by anomalous propagation (anaprop) can affect seriously radar rain rate estimates, particularly in fully automatic radar processing systems, and, if not filtered, can produce frequent false alarms. A statistical study of anomalous propagation detected from two operational C-band radars in the northern Italian region of Emilia Romagna is discussed, paying particular attention to its diurnal and seasonal variability. The analysis shows a high incidence of anaprop in summer, mainly in the morning and evening, due to the humid and hot summer climate of the Po Valley, particularly in the coastal zone. Thereafter, a comparison between different techniques and datasets to retrieve the vertical profile of the refractive index gradient in the boundary layer is also presented. In particular, their capability to detect anomalous propagation conditions is compared. Furthermore, beam path trajectories are simulated using a multilayer ray-tracing model and the influence of the propagation conditions on the beam trajectory and shape is examined. High resolution radiosounding data are identified as the best available dataset to reproduce accurately the local propagation conditions, while lower resolution standard TEMP data suffers from interpolation degradation and Numerical Weather Prediction model data (Lokal Model) are able to retrieve a tendency to superrefraction but not to detect ducting conditions. Observing the ray tracing of the centre, lower and upper limits of the radar antenna 3-dB half-power main beam lobe it is concluded that ducting layers produce a change in the measured volume and in the power distribution that can lead to an additional error in the reflectivity estimate and, subsequently, in the estimated rainfall rate.

Enhanced radar precipitation estimates using a combined clutter and beam blockage correction technique

Weather radar observations are currently the most reliable method for remote sensing of precipitation. However, a number of factors affect the quality of radar observations and may limit seriously automated quantitative applications of radar precipitation estimates such as those required in Numerical Weather Prediction (NWP) data assimilation or in hydrological models. In this paper, a technique to correct two different problems typically present in radar data is presented and evaluated. The aspects dealt with are non-precipitating echoes - caused either by permanent ground clutter or by anomalous propagation of the radar beam (anaprop echoes) - and also topographical beam blockage. The correction technique is based in the computation of realistic beam propagation trajectories based upon recent radiosonde observations instead of assuming standard radio propagation conditions. The correction consists of three different steps: 1) calculation of a Dynamic Elevation Map which provides the minimum clutter-free antenna elevation for each pixel within the radar coverage; 2) correction for residual anaprop, checking the vertical reflectivity gradients within the radar volume; and 3) topographical beam blockage estimation and correction using a geometric optics approach. The technique is evaluated with four case studies in the region of the Po Valley (N Italy) using a C-band Doppler radar and a network of raingauges providing hourly precipitation measurements. The case studies cover different seasons, different radio propagation conditions and also stratiform and convective precipitation type events. After applying the proposed correction, a comparison of the radar precipitation estimates with raingauges indicates a general reduction in both the root mean squared error and the fractional error variance indicating the efficiency and robustness of the procedure. Moreover, the technique presented is not computationally expensive so it seems well suited to be implemented in an operational environment.

Nucleation and growth of GaN nanorods on Si (111) surfaces by plasma-assisted molecular beam epitaxy - The influence of Si- and Mg-doping

The self-assembled growth of GaN nanorods on Si (111) substrates by plasma-assisted molecular beam epitaxy under nitrogen-rich conditions is investigated. An amorphous silicon nitride layer is formed in the initial stage of growth that prevents the formation of a GaN wetting layer. The nucleation time was found to be strongly influenced by the substrate temperature and was more than 30 min for the applied growth conditions. The observed tapering and reduced length of silicon-doped nanorods is explained by enhanced nucleation on nonpolar facets and proves Ga-adatom diffusion on nanorod sidewalls as one contribution to the axial growth. The presence of Mg leads to an increased radial growth rate with a simultaneous decrease of the nanorod length and reduces the nucleation time for high Mg concentrations.

Modifications in the Si valence band after ion-beam-induced oxidation

The changes undergone by the Si surface after oxygen bombardment have special interest for acquiring a good understanding of the Si+-ion emission during secondary ion mass spectrometry (SIMS) analysis. For this reason a detailed investigation on the stoichiometry of the builtup surface oxides has been carried out using in situ x-ray photoemission spectroscopy (XPS). The XPS analysis of the Si 2p core level indicates a strong presence of suboxide chemical states when bombarding at angles of incidence larger than 30°. In this work a special emphasis on the analysis and interpretation of the valence band region was made. Since the surface stoichiometry or degree of oxidation varies with the angle of incidence, the respective valence band structures also differ. A comparison with experimentally measured and theoretically derived Si valence band and SiO2 valence band suggests that the new valence bands are formed by a combination of these two. This arises from the fact that Si¿Si bonds are present on the Si¿suboxide molecules, and therefore the corresponding 3p-3p Si-like subband, which extends towards the Si Fermi level, forms the top of the respective new valence bands. Small variations in intensity and energy position for this subband have drastic implications on the intensity of the Si+-ion emission during sputtering in SIMS measurements. A model combining chemically enhanced emission and resonant tunneling effects is suggested for the variations observed in ion emission during O+2 bombardment for Si targets.

Structural and optical properties of dilute InAsN grown by molecular beam epitaxy

We perform a structural and optical characterization of InAs1¿xNx epilayers grown by molecular beam epitaxy on InAs substrates x 2.2% . High-resolution x-ray diffraction HRXRD is used to obtain information about the crystal quality and the strain state of the samples and to determine the N content of the films. The composition of two of the samples investigated is also obtained with time-of-flight secondary ion mass spectroscopy ToF-SIMS measurements. The combined analysis of the HRXRD and ToF-SIMS data suggests that the lattice parameter of InAsN might significantly deviate from Vegard"s law. Raman scattering and far-infrared reflectivity measurements have been carried out to investigate the incorporation of N into the InAsN alloy. N-related local vibrational modes are detected in the samples with higher N content. The origin of the observed features is discussed. We study the compositional dependence of the room-temperature band gap energy of the InAsN alloy. For this purpose, photoluminescence and optical absorption measurements are presented. The results are analyzed in terms of the band-anticrossing BAC model. We find that the room-temperature coupling parameter for InAsN within the BAC model is CNM=2.0 0.1 eV.

Networks of people in specialty production: family firms in the iron and steel Wire industries in Spain (1870-2000)

Capital intensive industries in specialized niches of production have constituted solid ground for family firms in Spain , as evidenced by the experience of the iron and steel wire industries between 1870 and 2000. The embeddedness of these firms in their local and regional environments have allowed the creation of networks that, together with favourable institutional conditions, significantly explain the dominance of family entrepreneurship in iron and steel wire manufacturing in Spain, until the end of the 20 th century. Dominance of family firms at the regional level has not been not an obstacle for innovation in wire manufacturing in Spain, which has taken place even when institutional conditions blocked innovation and traditional networking. Therefore, economic theories about the difficulties dynastic family firms may have to perform appropriately in science-based industries must be questioned

Hydroxyapatite coatings grown by pulsed laser deposition with a beam of 355 nm wavelength

Calcium phosphate coatings, obtained at different deposition rates by pulsed laser deposition with a Nd:YAG laser beam of 355-nm wavelength, were studied. The deposition rate was changed from 0.043 to 1.16 /shot by modification of only the ablated area, maintaining the local fluence constant to perform the ablation process in similar local conditions. Characterization of the coatings was performed by scanning electron microscopy, x-ray diffractometry, and infrared, micro-Raman, and x-ray photoelectron spectroscopy. The coatings showed a compact surface morphology formed by glassy gains with some droplets on them. Only hydroxyapatite (HA) and alpha-tricalcium phosphate (alpha-TCP) peaks were found in the x-ray diffractograms. The relative content of alpha TCP diminished with decreasing deposition rates, and only HA peaks were found for the lowest rate. The origin of alpha TCP is discussed.