Evaluation of internal navigation sensor suites for underground mining vehicle navigation

This paper describes a series of trials that were done at an underground mine in New South Wales, Australia. Experimental results are presented from the data obtained during the field trials and suitable sensor suites for an autonomous mining vehicle navigation system are evaluated.

Issues in autonomous navigation of underground vehicles

This paper describes current research at the Australian Centre for Field Robotics (ACFR) in collaboration with the Commonwealth Scientific and Industrial Research Organisation (CSIRO) within the Cooperative Research Centre (CRC) for Mining Technology and Equipment (CMTE) towards achieving autonomous navigation of underground vehicles, like a Load-Haul-Dump (LHD) truck. This work is being sponsored by the mining industry through the Australian Mineral Industries Research Association Limited (AMIRA). Robust and reliable autonomous navigation can only be realised by achieving high level tasks such as path-planning and obstacle avoidance. This requires determining the pose (position and orientation) of the vehicle at all times. A minimal infrastructure localisation algorithm that has been developed for this purpose is outlined and the corresponding results are presented. Further research issues that are under investigation are also outlined briefly.

Experiments in autonomous underground guidance

This paper presents the results of an experimental program for evaluating sensors and sensing technologies in an underground mining applications. The objective of the experiments is to infer what combinations of sensors will provide reliable navigation systems for autonomous vehicles operating in a harsh underground environment. Results from a wide range of sensors are presented and analysed. Conclusions as to a best combination of sensors are drawn.

Automation of underground LHD and truck haulage

This paper reviews the state-of-the-art in the automation of underground mining vehicles and reports on the development of an autonomous navigation system under development through the CMTE with sponsorship arranged by AMIRA. Past attempts at automating LHDs and haul trucks are described and their particular strengths and weaknesses are discussed. The auto-guidance system being developed overcomes some of the limitations of state-of-the-art prototype æcommercialÆ systems. It can be retrofitted to existing remote controlled vehicles, uses minimum installed infrastructure and is flexible enough for rapid relocation to alternate routes. The navigation techniques use data fusion of two separate sets of sensors combining natural feature recognition, nodal maps and inertial navigation techniques. Collision detection is incorporated and people and other traffic are excluded from the tramming area. This paper describes the work being done by the group with regard to auto-tramming and also outlines the future goals.

Automation of underground truck haulage

This paper reviews the state-of-the art in the automation of underground truck haulage. Past attemps at automating LHDs and haul trucks are described and their particular strengths and weaknesses are listed. We argue that the simple auto-tram...

Brief report regarding past fatigue incidents that have occurred at various BM Alliance Coal Operations mines in Queensland. Report to BM Alliance Coal Operation

This document has arisen from a request from BM Alliance Coal Operations Pty Ltd, to undertake and report on the key findings and statistics, key learning’s and recommendations for fatigue related incidents that have occurred at various BM Alliance coal operation mines in Queensland.

Brief report regarding past vehicle rollover and loss of traction incidents that have occurred at various BM Alliance Coal Operation mines in Queensland. Report to BM Alliance Coal Operation

This document has arisen from a request from BM Alliance Coal Operations Pty Ltd, to undertake and report on the key findings and statistics, key learning’s and recommendations for vehicle rollover and loss of traction (skid) incidents that have occurred at various BM Alliance coal operation mines in Queensland.

Evolved gas analysis of coal-derived pyrite/marcasite

The products evolved during the thermal decomposition of the coal-derived pyrite/marcasite were studied using simultaneous thermogravimetry coupled with Fourier-transform infrared spectroscopy and mass spectrometry (TG-FTIR–MS) technique. The main gases and volatile products released during the thermal decomposition of the coal-derived pyrite/marcasite are water (H2O), carbon dioxide (CO2), and sulfur dioxide (SO2). The results showed that the evolved products obtained were mainly divided into two processes: (1) the main evolved product H2O is mainly released at below 300 °C; (2) under the temperature of 450–650 °C, the main evolved products are SO2 and small amount of CO2. It is worth mentioning that SO3 was not observed as a product as no peak was observed in the m/z = 80 curve. The chemical substance SO2 is present as the main gaseous product in the thermal decomposition for the sample. The coal-derived pyrite/marcasite is different from mineral pyrite in thermal decomposition temperature. The mass spectrometric analysis results are in good agreement with the infrared spectroscopic analysis of the evolved gases. These results give the evidence on the thermal decomposition products and make all explanations have the sufficient evidence. Therefore, TG–MS–IR is a powerful tool for the investigation of gas evolution from the thermal decomposition of materials.

Hydrostratigraphic and hydrochemical characterisation of aquifers, aquitards and coal seams in the Galilee and Eromanga basins, Central Queensland, Australia

Inter-aquifer mixing studies are usually made carrying out hydrochemical and isotopic techniques only. In this thesis these techniques have been integrated with three-dimensional geological modelling proving to be a better approach for inter—aquifer mixing assessment in regional areas, and also highlighting the influence of faulting in the understanding of groundwater and gas migration, which could not be possible using the two fist techniques alone. The results are of particular interest for coal seam gas basins and can even be used as exploration tools as areas of higher permeability and gas migration were identified.

Noise in my head: Voices from the ugly Australian underground

The Ugly Australian Underground documents the music, songwriting, aesthetics and struggles of fifty of Australia’s most innovative and significant bands and artists currently at the creative peak of their careers. The book provides a rare insight into the critically heralded cult music scene in Australia. The author, Jimi Kritzler, is both a journalist and a musician, and is personally connected to the musicians he interviews through his involvement in this music subculture. The interviews are extremely personal and reveal much more than any interview granted to street press or blogs. They deal with not only the music and songwriting processes of each band, but in some circumstances their struggles with drugs, involvement in crime and the death of band members.

Cyclic Salinity Model for deposition of large-scale coal deposits

Existing field data for Rangal coals (Late Permian) of the Bowen Basin, Queensland, Australia, are inconsistent with the depositional model generally accepted in the current geological literature to explain coal deposition. Given the apparent unsuitability of the current depositional model to the Bowen Basin coal data, a new depositional model, here named the Cyclic Salinity Model, is proposed and tested in this study.

Visual control of an electrohydraulic manipulator for underground mining applications

A large range of underground mining equipment makes use of compliant hydraulic arms for tasks such as rock-bolting, rock breaking, explosive charging and shotcreting. This paper describes a laboratory model electo-hydraulic manipulator which is used to prototype novel control and sensing techniques. The research is aimed at improving the safety and productivity of these mining tasks through automation, in particular the application of closed-loop visual positioning of the machine's end-effector.