Development of autonomous maintenance in a furniture company

This article presents a work performed in the maintenance department of a furniture company in Portugal, in order to develop and implement autonomous maintenance. The main objective of the project was related to the objective to increase and make effective the autonomous maintenance tasks performed by production operators, and in this way avoiding unplanned downtime due to equipment failures. Although some autonomous maintenance tasks were already carried out within the company, a preliminary study revealed weaknesses in the application of this tool. In the initial phase of this pilot project, the main problems encountered at the level of autonomous maintenance were related to the lack of time to carry out these tasks, showing that the stipulated procedures were far from the real needs of the company. To solve these problems a pilot project was conducted, making several changes in the performance of autonomous maintenance tasks, making them standard and adapted to reality of each production line. There was a general improvement in the factory indicators, and essentially there was a behavioral change, since the operators felt that their opinions were taking into account and began to understand the importance of small tasks performed by them.

Implementation of a lean six sigma project in a production line

Companies from the motorcycles components branch are dealing with a dynamic environment, resulting from the introduction of new products and the increase of market demand. This dynamic environment requires frequent changes in production lines and requires flexibility in the processes, which can cause reductions in the level of quality and productivity. This paper presents a Lean Six Sigma improvement project performed in a production line of the company's machining sector, in order to eliminate losses that cause low productivity, affecting the fulfillment of the production plan and customer satisfaction. The use of Lean methodology following the DMAIC stages allowed analyzing the factors that influence the line productivity loss. The major problems and causes that contribute to a reduction on productivity and that were identified in this study are the lack of standardization in the setup activities and the excessive stoppages for adjustment of the processes that caused an increase of defects. Control charts, Pareto analysis and cause-and-effect diagrams were used to analyze the problem. On the improvement stage, the changes were based on the reconfiguration of the line layout as well as the modernization of the process. Overall, the project justified an investment in new equipment, the defective product units were reduced by 84% and an increase of 29% of line capacity was noticed.

Estudo do trabalho numa empresa de produção de pneus e implementação de ferramentas Lean

Dissertação de mestrado integrado em Engenharia e Gestão Industrial

Improvement of in silico strain engineering methods in Saccharomyces cerevisiae

PhD thesis in Bioengineering

Aplicação de metodologias Lean na secção de tecelagem de uma empresa têxtil

Dissertação de mestrado integrado em Engenharia e Gestão Industrial

Análise da qualidade do serviço numa empresa transportadora

Dissertação de mestrado integrado em Engenharia e Gestão Industrial

Coagulation/flocculation/flotation/nanofiltration processes using Moringa Oleifera as coagulant of Eutrophized river

This study investigated the efficiency of Moringa oleifera (MO) seeds as natural coagulant in coagulation/flocculation/dissolved air flotation (C/F/DAF), followed by nanofiltration (NF) for Microcystis protocystis and microcystin-LR removal. The methodology adopted in this work was performed in two steps: 1) coagulation/flocculation/dissolved air flotation (C/F/DAF) process using the MO extracted in saline solution of potassium chloride (KCl-1M) and sodium chloride (NaCl-1M) in optimum dosage 50 mg·L-1; 2) nanofiltration process using NF90 and NF270 membrane provided Dow Chemical Company®. A working pressure of 8 bar was applied. In all samples were analyzed color, turbidity, pH, cyanobacterial cells count and microcystin concentration. The use of MO seeds as natural coagulant, obtained satisfactory results in the M. protocystis, color and turbidity removal. NF was able to completely remove cyanobacterial cells and microcystins (100 %) from M. protocystis (always under the quantification limit). Therefore, C/F/DAF+NF sequence is a safe barrier against M. protocystis and microcystins in drinking water.

Narrative innovations predict symptom improvement: Studying innovative moments in narrative therapy of depression

Objective:Innovative moments (IMs) are moments in the therapeutic dialog that constitute exceptions toward the client's problems. These narrative markers of meaning transformation are associated with change in different models of therapy and diverse diagnoses. Our goal is to test if IMs precede symptoms change, or, on the contrary, are a mere consequence of symptomatic 15 change. Method: For this purpose, IMs and symptomatology (Outcome Questionnaire-10.2) were assessed at every session in a sample of 10 cases of narrative therapy for depression. Hierarchical linear modeling was conducted to explore whether (i) IMs in a given session predict patients' symptoms in the following session and/or (ii) symptoms in a given session predict IMs in the next session. Results: Results suggested that IMs are better predictors of symptoms than the reverse. Conclusions: These results are discussed considering the contribution of meanings and narrative processes' changes to symptomatic improvement.

Impacto do azoto no processo de soldadura reflow

Dissertação de mestrado em Engenharia Industrial (área de especialização em Qualidade, Segurança e Manutenção)

Aplicação da metodologia WID numa indústria de calçado

Dissertação de mestrado em Engenharia Industrial

Modelação de processos e implementação de ferramentas de Planeamento e Controlo da Produção numa empresa de produção de resguardos de banho

Dissertação de mestrado em Engenharia Industrial

Implementação de técnicas e princípios de produção lean no processo de pré-confeção de uma indústria de cablagens

Dissertação de mestrado em Engenharia Industrial

Análise de dados e aplicação de modelos estatísticos para apoio à decisão de contratação na Petróleo Brasileiro

Dissertação de mestrado em Engenharia Industrial

Implementação de ferramentas Lean numa empresa de componentes para calçado

Dissertação de mestrado em Engenharia Industrial

A comunicação do compromisso para com o desenvolvimento sustentável, das organizações portuguesas certificadas em qualidade, ambiente e segurança

Dissertação de mestrado em Engenharia Industrial (área de especialização em Qualidade, Segurança e Manutenção)