Purification of pharmaceuticals and nutraceutical compounds by sub- and supercritical extraction and chromatography

This thesis discusses the use of sub- and supercritical fluids as the medium in extraction and chromatography. Super- and subcritical extraction was used to separate essential oils from herbal plant Angelica archangelica. The effect of extraction parameters was studied and sensory analyses of the extracts were done by an expert panel. The results of the sensory analyses were compared to the analytically determined contents of the extracts. Sub- and supercritical fluid chromatography (SFC) was used to separate and purify high-value pharmaceuticals. Chiral SFC was used to separate the enantiomers of racemic mixtures of pharmaceutical compounds. Very low (cryogenic) temperatures were applied to substantially enhance the separation efficiency of chiral SFC. The thermodynamic aspects affecting the resolving ability of chiral stationary phases are briefly reviewed. The process production rate which is a key factor in industrial chromatography was optimized by empirical multivariate methods. General linear model was used to optimize the separation of omega-3 fatty acid ethyl esters from esterized fish oil by using reversed-phase SFC. Chiral separation of racemic mixtures of guaifenesin and ferulic acid dimer ethyl ester was optimized by using response surface method with three variables per time. It was found that by optimizing four variables (temperature, load, flowate and modifier content) the production rate of the chiral resolution of racemic guaifenesin by cryogenic SFC could be increased severalfold compared to published results of similar application. A novel pressure-compensated design of industrial high pressure chromatographic column was introduced, using the technology developed in building the deep-sea submersibles (Mir 1 and 2). A demonstration SFC plant was built and the immunosuppressant drug cyclosporine A was purified to meet the requirements of US Pharmacopoeia. A smaller semi-pilot size column with similar design was used for cryogenic chiral separation of aromatase inhibitor Finrozole for use in its development phase 2.

TlBr raw material purification, crystal growth, annealing, detector fabrication and characterisation for gamma-ray detector applications

The research reported in this thesis dealt with single crystals of thallium bromide grown for gamma-ray detector applications. The crystals were used to fabricate room temperature gamma-ray detectors. Routinely produced TlBr detectors often are poor quality. Therefore, this study concentrated on developing the manufacturing processes for TlBr detectors and methods of characterisation that can be used for optimisation of TlBr purity and crystal quality. The processes under concern were TlBr raw material purification, crystal growth, annealing and detector fabrication. The study focused on single crystals of TlBr grown from material purified by a hydrothermal recrystallisation method. In addition, hydrothermal conditions for synthesis, recrystallisation, crystal growth and annealing of TlBr crystals were examined. The final manufacturing process presented in this thesis deals with TlBr material purified by the Bridgman method. Then, material is hydrothermally recrystallised in pure water. A travelling molten zone (TMZ) method is used for additional purification of the recrystallised product and then for the final crystal growth. Subsequent processing is similar to that described in the literature. In this thesis, literature on improving quality of TlBr material/crystal and detector performance is reviewed. Aging aspects as well as the influence of different factors (temperature, time, electrode material and so on) on detector stability are considered and examined. The results of the process development are summarised and discussed. This thesis shows the considerable improvement in the charge carrier properties of a detector due to additional purification by hydrothermal recrystallisation. As an example, a thick (4 mm) TlBr detector produced by the process was fabricated and found to operate successfully in gamma-ray detection, confirming the validity of the proposed purification and technological steps. However, for the complete improvement of detector performance, further developments in crystal growth are required. The detector manufacturing process was optimized by characterisation of material and crystals using methods such as X-ray diffraction (XRD), polarisation microscopy, high-resolution inductively coupled plasma mass (HR-ICPM), Fourier transform infrared (FTIR), ultraviolet and visual (UV-Vis) spectroscopy, field emission scanning electron microscope (FESEM) and energy-dispersive X-ray spectroscopy (EDS), current-voltage (I-V) and capacity voltage (CV) characterisation, and photoconductivity, as well direct detector examination.

Molecular details of phage phi6 RNA-dependent RNA synthesis

For most RNA viruses RNA-dependent RNA polymerases (RdRPs) encoded by the virus are responsible for the entire RNA metabolism. Thus, RdRPs are critical components in the viral life cycle. However, it is not fully understood how these important enzymes function during viral replication. Double-stranded RNA (dsRNA) viruses perform the synthesis of their RNA genome within a proteinacous viral particle containing an RdRP as a minor constituent. The phi6 bacteriophage is the best-studied dsRNA virus, providing an excellent background for studies of its RNA synthesis. The purified recombinant phi6 RdRP is highly active in vitro and it possesses both RNA replication and transcription activities. The crystal structure of the phi6 polymerase, solved in complex with a number of ligands, provides a working model for detailed in vitro studies of RNA-dependent RNA polymerization. In this thesis, the primer-independent initiation of the phi6 RdRP was studied in vitro using biochemical and structural methods. A C-terminal, four-amino-acid-long loop protruding into the central cavity of the phi6 RdRP has been suggested to stabilize the incoming nucleotides of the initiation complex formation through stacking interactions. A similar structural element has been found from several other viral RdRPs. In this thesis, this so-called initiation platform loop was subjected to site-directed mutagenesis to address its role in the initiation. It was found that the initiation mode of the mutants is primer-dependent, requiring either an oligonucleotide primer or a back-priming initiation mechanism for the RNA synthesis. The crystal structure of a mutant RdRP with altered initiation platform revealed a set of contacts important for primer-independent initiation. Since phi6 RdRP is structurally and functionally homologous to several viral RdRPs, among them the hepatitis C virus RdRP, these results provide further general insight to understand primer-independent initiation. In this study it is demonstrated that manganese phasing could be used as a practical tool for solving structures of large proteins with a bound manganese ion. The phi6 RdRP was used as a case study to obtain phases for crystallographic analysis. Manganese ions are naturally bound to the phi6 RdRP at the palm domain of the enzyme. In a crystallographic experiment, X-ray diffraction data from a phi6 RdRP crystal were collected at a wavelength of 1.89 Å, which is the K edge of manganese. With this data an automatically built model of the core region of the protein could be obtained. Finally, in this work terminal nucleotidyl transferase (TNTase) activity of the phi6 RdRP was documented in the isolated polymerase as well as in the viral particle. This is the first time that such an activity has been reported in a polymerase of a dsRNA virus. The phi6 RdRP used uridine triphosphates as the sole substrate in a TNTase reaction but could accept several heterologous templates. The RdRP was able to add one or a few non-templated nucleotides to the 3' end of the single- or double-stranded RNA substrate. Based on the results on particle-mediated TNTase activity and previous structural information of the polymerase, a model for termination of the RNA-dependent RNA synthesis is suggested in this thesis.

Folates in rye: Determination and enhancement by food processing

The average daily intake of folate, one of the B vitamins, falls below recommendations among the Finnish population. Bread and cereals are the main sources of folate, rye being the most significant single source. Processing is a prerequisite for the consumption of whole grain rye; however, little is known about the effect of processing on folates. Moreover, data on the bioavailability of endogenous cereal folates are scarce. The aim of this study was to examine the variation in as well as the effect of fermentation, germination, and thermal processes on folate contents in rye. Bioavailability of endogenous rye folates was investigated in a four-week human intervention study. One of the objectives throughout the work was to optimise and evaluate analytical methods for determining folate contents in cereals. Affinity chromatographic purification followed by high-performance liquid chromatography (HPLC) was a suitable method for analysing cereal products for folate vitamers, and microbiological assay with Lactobacillus rhamnosus reliably quantified the total folate. However, HPLC gave approximately 30% lower results than the microbiological assay. The folate content of rye was high and could be further increased by targeted processing. The vitamer distribution of whole grain rye was characterised by a large proportion of formylated vitamers followed by 5-methyltetrahydrofolate. In sourdough fermentation of rye, the studied yeasts synthesized and lactic acid bacteria mainly depleted folate. Two endogenous bacteria isolated from rye flour were found to produce folate during fermentation. Inclusion of baker s yeast in sourdough fermentation raised the folate level so that the bread could contain more folate than the flour it was made of. Germination markedly increased the folate content of rye, with particularly high folate concentrations in hypocotylar roots. Thermal treatments caused significant folate losses but the preceding germination compensated well for the losses. In the bioavailability study, moderate amounts of endogenous folates in the form of different rye products and orange juice incorporated in the diet improved the folate status among healthy adults. Endogenous folates from rye and orange juice showed similar bioavailability to folic acid from fortified white bread. In brief, it was shown that the folate content of rye can be enhanced manifold by optimising and combining food processing techniques. This offers some practical means to increase the daily intake of folate in a bioavailable form.

Heterotrophic Bacteria Associated with Cyanobacteria in Recreational and Drinking Water

Cyanobacterial mass occurrences, also known as water blooms, have been associated with adverse health effects of both humans and animals. They can also be a burden to drinking water treatment facilities. Risk assessments of the blooms have generally focused on the cyanobacteria themselves and their toxins. However, heterotrophic bacteria thriving among cyanobacteria may also be responsible for many of the adverse health effects, but their role as the etiological agents of these health problems is poorly known. In addition, studies on the water purification efficiency of operating water treatment plants during cyanobacterial mass occurrences in their water sources are rare. In the present study, over 600 heterotrophic bacterial strains were isolated from natural freshwater, brackish water or from treated drinking water. The sampling sites were selected as having frequent cyanobacterial occurrences in the water bodies or in the water sources of the drinking water treatment plants. In addition, samples were taken from sites where cyanobacterial water blooms were surmised to have caused human health problems. The isolated strains represented bacteria from 57 different genera of the Gamma-, Alpha- or Betaproteobacteria, Actinobacteria, Flavobacteria, Sphingobacteria, Bacilli and Deinococci classes, based on their partial 16S rRNA sequences. Several isolates had no close relatives among previously isolated bacteria or cloned 16S rRNA genes of uncultivated bacteria. The results show that water blooms are associated with a diverse community of cultivable heterotrophic bacteria. Chosen subsets of the isolated strains were analysed for features such as their virulence gene content and possible effect on cyanobacterial growth. Of the putatively pathogenic haemolytic strains isolated in the study, the majority represented the genus Aeromonas. Therefore, the Aeromonas spp. strains isolated from water samples associated with adverse health effects were screened for the virulence gene types encoding for enterotoxins (ast, alt and act/aerA/hlyA), flagellin subunits (flaA/flaB), lipase (lip/pla/lipH3/alp-1) and elastase (ahyB) by PCR. The majority (90%) of the Aeromonas strains included one or more of the six screened Aeromonas virulence gene types. The most common gene type was act, which was present in 77% of the strains. The fla, ahyB and lip genes were present in 30 37% of the strains. The prevalence of the virulence genes implies that the Aeromonas may be a factor in some of the cyanobacterial associated health problems. Of the 183 isolated bacterial strains that were studied for possible effects on cyanobacterial growth, the majority (60%) either enhanced or inhibited growth of cyanobacteria. In most cases, they enhanced the growth, which implies mutualistic interactions. The results indicate that the heterotrophic bacteria have a role in the rise and fall of the cyanobacterial water blooms. The genetic and phenotypic characteristics and the ability to degrade cyanobacterial hepatotoxins of 13 previously isolated Betaproteobacteria strains, were also studied. The strains originated from Finnish lakes with frequent cyanobacterial occurrence. Tested strains degraded microcystins -LR and -YR and nodularin. The strains could not be assigned to any described bacterial genus or species based on their genetic or phenotypic features. On the basis of their characteristics a new genus and species Paucibacter toxinivorans was proposed for them. The water purification efficiency of the drinking water treatment processes during cyanobacterial water bloom in water source was assessed at an operating surface water treatment plant. Large phytoplankton, cyanobacterial hepatotoxins, endotoxins and cultivable heterotrophic bacteria were efficiently reduced to low concentrations, often below the detection limits. In contrast, small planktonic cells, including also possible bacterial cells, regularly passed though the water treatment. The passing cells may contribute to biofilm formation within the water distribution system, and therefore lower the obtained drinking water quality. The bacterial strains of this study offer a rich source of isolated strains for examining interactions between cyanobacteria and the heterotrophic bacteria associated with them. The degraders of cyanobacterial hepatotoxins could perhaps be utilized to assist the removal of the hepatotoxins during water treatment, whereas inhibitors of cyanobacterial growth might be useful in controlling cyanobacterial water blooms. The putative pathogenicity of the strains suggests that the health risk assessment of the cyanobacterial blooms should also cover the heterotrophic bacteria.

Food and Indoor Air Isolated Bacillus Non-Protein Toxins: : Structures, Physico-Chemical Properties and Mechanisms of Effects on Eukaryotic Cells

We report here the structures and properties of heat-stable, non-protein, and mammalian cell-toxic compounds produced by spore-forming bacilli isolated from indoor air of buildings and from food. Little information is available on the effects and occurrence of heat-stable non-protein toxins produced by bacilli in moisture-damaged buildings. Bacilli emit spores that move in the air and can serve as the carriers of toxins, in a manner similar to that of the spores of toxic fungi found in contaminated indoor air. Bacillus spores in food cause problems because they tolerate the temperatures applied in food manufacture and the spores later initiate growth when food storage conditions are more favorable. Detection of the toxic compounds in Bacillus is based on using the change in mobility of boar spermatozoa as an indicator of toxic exposure. GC, LC, MS, and nuclear magnetic resonance NMR spectroscopy were used for purification, detection, quantitation, and analysis of the properties and structures of the compounds. Toxicity and the mechanisms of toxicity of the compounds were studied using boar spermatozoa, feline lung cells, human neural cells, and mitochondria isolated from rat liver. The ionophoric properties were studied using the BLM (black-lipid membrane) method. One novel toxin, forming ion channels permeant to K+ > Na+ > Ca2+, was found and named amylosin. It is produced by B. amyloliquefaciens isolated from indoor air of moisture-damaged buildings. Amylosin was purified with an RP-HPLC and a monoisotopic mass of 1197 Da was determined with ESI-IT-MS. Furthermore, acid hydrolysis of amylosin followed by analysis of the amino acids with the GS-MS showed that it was a peptide. The presence of a chromophoric polyene group was found using a NMR spectroscopy. The quantification method developed for amylosin based on RP-HPLC-UV, using the macrolactone polyene, amphotericin B (MW 924), as a reference compound. The B. licheniformis strains isolated from a food poisoning case produced a lipopeptide, lichenysin A, that ruptured mammalian cell membranes and was purified with a LC. Lichenysin A was identified by its protonated molecules and sodium- and potassium- cationized molecules with MALDI-TOF-MS. Its protonated forms were observed at m/z 1007, 1021 and 1035. The amino acids of lichenysin A were analyzed with ESI-TQ-MS/MS and, after acid hydrolysis, the stereoisomeric forms of the amino acids with RP-HPLC. The indoor air isolates of the strain of B. amyloliquefaciens produced not only amylosin but also lipopeptides: the cell membrane-damaging surfactin and the fungicidal fengycin. They were identified with ESI-IT-MS observing their protonated molecules, the sodium- and potassium-cationized molecules and analysing the MS/MS spectra. The protonated molecules of surfactin and fengycin showed m/z values of 1009, 1023, and 1037 and 1450, 1463, 1493, and 1506, respectively. Cereulide (MW 1152) was purified with RP-HPLC from a food poisoning strain of B. cereus. Cereulide was identified with ESI-TQ-MS according to the protonated molecule observed at m/z 1154 and the ammonium-, sodium- and potassium-cationized molecules observed at m/z 1171, 1176, and 1192, respectively. The fragment ions of the MS/MS spectrum obtained from the protonated molecule of cereulide at m/z 1154 were also interpreted. We developed a quantification method for cereulide, using RP-HPLC-UV and valinomycin (MW 1110, which structurally resembles cereulide) as the reference compound. Furthermore, we showed empirically, using the BLM method, that the emetic toxin cereulide is a specific and effective potassium ionophore of whose toxicity target is especially the mitochondria.

L-rhamnose-1-dehydrogenase gene and L-rhamnose catabolism in the yeast Pichia stipitis

The purpose of this work was to identify some of the genes of the catabolic route of L-rhamnose in the yeast Pichia stipitis. There are at least two distinctly different pathways for L-rhamnose catabolism. The one described in bacteria has phosphorylated intermediates and the enzymes and the genes of this route have been described. The pathway described in yeast does not have phosphorylated intermediates. The intermediates and the enzymes of this pathway are known but none of the genes have been identified. The work was started by purifying the L-rhamnose dehydrogenase, which oxidates L-rhamnose to rhamnonic acid-gamma-lactone. NAD is used as a cofactor in this reaction. A DEAE ion exchange column was used for purification. The active fraction was further purified using a non-denaturing PAGE and the active protein identified by zymogram staining. In the last step the protein was separated in a SDS-PAGE, the protein band trypsinated and analysed by MALDI-TOF MS. This resulted in the identification of the corresponding gene, RHA1, which was then, after a codon change, expressed in Saccharomyces cerevisiae. Also C- or N-terminal histidine tags were added but as the activity of the enzyme was lost or strongly reduced these were not used. The kinetic properties of the protein were analysed in the cell extract. Substrate specifity was tested with different sugars; L-rhamnose, L-lyxose and L-mannose were oxidated by the enzyme. Vmax values were 180 nkat/mg, 160 nkat/mg and 72 nkat/mg, respectively. The highest affinity was towards L-rhamnose, the Km value being 0.9 mM. Lower affinities were obtained with L-lyxose, Km 4.3 mM, and L-mannose Km 25 mM. Northern analysis was done to study the transcription of RHA1 with different carbon sources. Transcription was observed only on L-rhamnose suggesting that RHA1 expression is L-rhamnose induced. A RHA1 deletion cassette for P. stipitis was constructed but the cassette had integrated randomly and not targeted to delete the RHA1 gene. Enzyme assays for L-lactaldehyde dehydrogenase were done similarly to L-rhamnose dehydrogenase assays. NAD is used as a cofactor also in this reaction where L-lactaldehyde is oxidised to L-lactate. The observed enzyme activities were very low and the activity was lost during the purification procedures.

Stretching single DNA-molecules with temperature-stabilized optical tweezers

This thesis consists of two parts; in the first part we performed a single-molecule force extension measurement with 10kb long DNA-molecules from phage-λ to validate the calibration and single-molecule capability of our optical tweezers instrument. Fitting the worm-like chain interpolation formula to the data revealed that ca. 71% of the DNA tethers featured a contour length within ±15% of the expected value (3.38 µm). Only 25% of the found DNA had a persistence length between 30 and 60 nm. The correct value should be within 40 to 60 nm. In the second part we designed and built a precise temperature controller to remove thermal fluctuations that cause drifting of the optical trap. The controller uses feed-forward and PID (proportional-integral-derivative) feedback to achieve 1.58 mK precision and 0.3 K absolute accuracy. During a 5 min test run it reduced drifting of the trap from 1.4 nm/min in open-loop to 0.6 nm/min in closed-loop.

F-18 Labelling Synthesis, Radioanalysis and Evaluation of A Dopamine Transporter and A Hypoxia Tracer

Positron emission tomography (PET) is an imaging technique in which radioactive positron-emitting tracers are used to study biochemical and physiological functions in humans and in animal experiments. The use of PET imaging has increased rapidly in recent years, as have special requirements in the fields of neurology and oncology for the development of syntheses for new, more specific and selective radiotracers. Synthesis development and automation are necessary when high amounts of radioactivity are needed for multiple PET studies. In addition, preclinical studies using experimental animal models are necessary for evaluating the suitability of new PET tracers for humans. For purification and analysing the labelled end-product, an effective radioanalytical method combined with an optimal radioactivity detection technique is of great importance. In this study, a fluorine-18 labelling synthesis method for two tracers was developed and optimized, and the usefulness of these tracers for possible prospective human studies was evaluated. N-(3-[18F]fluoropropyl)-2β-carbomethoxy-3β-(4-fluorophenyl)nortropane ([18F]β-CFT-FP) is a candidate PET tracer for the dopamine transporter (DAT), and 1H-1-(3-[18F]fluoro-2-hydroxypropyl)-2-nitroimidazole ([18F]FMISO) is a well-known hypoxia marker for hypoxic but viable cells in tumours. The methodological aim of this thesis was to evaluate the status of thin-layer chromatography (TLC) combined with proper radioactivity detection measurement systems as a radioanalytical method. Three different detection methods of radioactivity were compared: radioactivity scanning, film autoradiography, and digital photostimulated luminescence (PSL) autoradiography. The fluorine-18 labelling synthesis for [18F]β-CFT-FP was developed and carbon-11 labelled [11C]β-CFT-FP was used to study the specificity of β-CFT-FP for the DAT sites in human post-mortem brain slices. These in vitro studies showed that β-CFT-FP binds to the caudate-putamen, an area rich of DAT. The synthesis of fluorine-18 labelled [18F]FMISO was optimized, and the tracer was prepared using an automated system with good and reproducible yields. In preclinical studies, the action of the radiation sensitizer estramustine phosphate on the radiation treatment and uptake of [18F]FMISO was evaluated, with results of great importance for later human studies. The methodological part of this thesis showed that radioTLC is the method of choice when combined with an appropriate radioactivity detection technique. Digital PSL autoradiography proved to be the most appropriate when compared to the radioactivity scanning and film autoradiography methods. The very high sensitivity, good resolution, and wide dynamic range of digital PSL autoradiography are its advantages in detection of β-emitting radiolabelled substances.

Ionic Liquids and Microwaves in Promotion of Organic Synthesis : Friedel-Crafts reaction, deuterolabelling and O-Demethylation

The use of ionic liquids in chemical research has gained considerable interest and activity in recent years. Due to their unique and varied physicochemical properties, in comparison to molecular solvents, the potential applications for ionic liquids are enormous. The use of microwave irradiation, as a powerful dielectric heating technique, in synthetic organic chemistry has been known since 1986. Since then, it has gained significant recognition for its research and application in both academia and industry. The use of either ionic liquids or microwave irradiation in synthetic organic chemistry has been known to afford improved, alternative or complimentary selectivities, in comparison to traditional processes. In this study, the use of ionic liquids as solvents, co-solvents and catalytic media was explored in Friedel-Crafts, deuterolabelling and O-demethylation reactions. Alternative methods for the production of a variety of aromatic ketones using the Friedel-Crafts acylation methodology were investigated using ionic liquid catalyst or ionic liquid acidic additive systems. The disclosed methods, i.e. metal bistriflamides and chloroindate ionic liquids systems, possessed good catalytic activity in the synthesis of typical benzophenones. These catalytic systems were also recyclable. Microwave irradiation was found to be useful in the synthesis of various polyhydroxydeoxybenzoins and arylpropanones as synthetic precursors to naturally occurring or potentially bioactive compounds. Under optimized condition, the reaction occurred in only four minutes using systems such as [bmim][NTf2]/HNTf2 and [bmim][BF4]/BF3·OEt2. Naturally occurring polyphenols, such as isoflavones, can possess various types of biological or pharmacological activity. In particular, some are noted for their beneficial effects on human health. Isotopically labelled analogues of polyphenols are valuable as analytical standards in the quantification of these compounds from biological matrices. A new strategy for deuterolabelling of polyphenols was developed using ionic liquids as co-solvents and 35% DCl/D2O, as a cheap deuterium source, under microwave irradiation. Under these conditions, perdeuterated compounds were achieved in short reaction times, in high isotopic purity and in excellent yields. An O-demethylation reaction was developed, using an ionic liquid reaction medium with BBr3 for the deprotection of a variety methyl protected polyphenolic compounds, such as isoflavons and lignans. This deprotection procedure was found to be very practical as the reaction occurred under mild reaction conditions and in short reaction times. The isolation and purification steps were particularly straightforward and high yielding, in comparison to traditional methods.

Pyhä Teresa ja keskiajan mystiikan teoriat

In my dissertation I have studied St Teresa (1515-1582) in the light of medieval mystical theories. I have two main levels in my research: historical and theological. On the historical level I study St Teresa s personal history in the context of her family and the Spanish society. On the theological level I study both St Teresa s mysticism and her religious experience in the light of medieval mysticism. St Teresa wrote a book called Life , which is her narrative autobiography and story about her mystical spiritual formation. She reflected herself through biblical texts interpreting them in the course of the biblical hermeneutics like allegory, typology, tropology and anagogy. In addition to that she read others life stories from her period of time, but reflected herself only slightly through the sociological point of view. She used irony as a means to gain acceptance to her authority and motive to write. Her position has been described as a double bind because of writing at the request of educated men and to the non-educated women as she herself was uneducated. She used irony as a means to achieve valuation to women, to gain negative attributes connected to them and to gain authority to teach them mystical spirituality, the Bible and prayer. In this ironic tendency she was a feminist writer. In order to understand medieval mysticism I have written in the first chapter a review of the main trends in medieval mysticism in connection with the classical emotional theories. Two medieval mystical theories show an important role in St Teresa s mysticism. One is love mysticism and the other is the three partite way of mysticism (purification, illumination and union). The classic-philosophical emotional theories play a role in both patterns. The theory of love mysticism St Teresa interpreted in the traditional way stressing the spiritual meaning of love in connexion with God and neighbors. Love is an emotion, which is bound with other emotions, but all objects of love don t strengthen spiritual love. In the three partite way of mysticism purification means to find biblical values in life and to practice meditative self-knowledge theologically interpreted. In illumination human understanding has to be illuminated by God and united to mystical knowledge from God. St Teresa considered illumination a way to learn things. Illumination has also psychological aspects like recognition of many trials and pains, which come from life on earth. Theologically interpreted in illumination one should die to oneself, let oneself be transformed and renewed by God. I have also written a review of the modern philosophical discussion on personal identity where memory and mental experiences are important creators of personal identity. St Teresa bound medieval mystical teaching together with her personal religious experience. Her personal identity is by its character based on her narrative life story where mental experiences play important role. Previous researchers have labelled St Teresa as an ecstatic person whose experiences produced ecstatic phenomena to the mysticism. These phenomena combined with visions have in one respect made of her a person who has brought physical and visionary tendencies to theology. In spite of that she also represents a modern tendency trying to give words to experiences, which at first seem to be exceptional and extreme and which are easily interpreted as one-sided either physical or sexual or unsaid. In other respect I have stressed the personality of St Teresa that was represented as both strong and weak. The strong personality for her is demonstrated by religious faith and in its practice. The weak personality was for her a natural personal identity. St Teresa saw a unifying aspect in almost all. Firstly, her mysticism was aimed towards union with God and secondly, the unifying aspects and common rules in human relations in community life were central. Union with God is based on the fact that in a soul God is living in its centre, where God is present in the Trinitarian way. The picture of God in ourselves is a mirror but to get to know God better is to recognize his/her presence in us. When the soul recognizes itself as a dwelling place of God, it knows itself as God knows him/herself. There is equality between God and the soul. To be a Christian means to participate in God in his Trinitarian being. The participation to God is a process of divinization that puts a person into transformation, change and renewal. The unitive aspect concludes also knowledge of opposites between experience of community and solitude as well as community and separateness. As a founder of monasteries St Teresa practiced theology of poverty. She renewed the monastic life founding a rule called discalced that stressed ascetic tendencies. Supporters of her work were after the difficulties in the beginning both society and churchly leaders. She wrote about the monasteries including in her description at times seriousness at times humor and irony. Her stories are said to be picaresque histories that contain stories of ordinary laymen and many unexpected occasions. She exercised a kind of Bakhtinian dialogue in her letters. St Teresa stressed the virtues like sacrifice, determination and courage in the monastic life. Most of what she taught of virtues is based on biblical spirituality but there are also psychological tendencies in her writings. The theological pedagogical advice is mixed with psychology, but she herself made no distinction between different aspects in her teaching. To understand St Teresa and her mysticism is to recognize that she mixes her personal religious experience and mysticism, which widens mysticism to religious experience in a new way, although this corresponds also the very definition of mysticism. St Teresa concentrated on mental-spiritual experiences and the aim of her mystical teaching was to produce a human mind well cured like a garden that has God as its gardener.

DNA Packaging and Host Cell Lysis: Late Events in Bacteriophage PRD1 Infection

The object of this study is a tailless internal membrane-containing bacteriophage PRD1. It has a dsDNA genome with covalently bound terminal proteins required for replication. The uniqueness of the structure makes this phage a desirable object of research. PRD1 has been studied for some 30 years during which time a lot of information has accumulated on its structure and life-cycle. The two least characterised steps of the PRD1 life-cycle, the genome packaging and virus release are investigated here. PRD1 shares the main principles of virion assembly (DNA packaging in particular) and host cell lysis with other dsDNA bacteriophages. However, this phage has some fascinating individual peculiarities, such as DNA packaging into a membrane vesicle inside the capsid, absence of apparent portal protein, holin inhibitor and procapsid expansion. In the course of this study we have identified the components of the DNA packaging vertex of the capsid, and determined the function of protein P6 in packaging. We managed to purify the procapsids for an in vitro packaging system, optimise the reaction and significantly increase its efficiency. We developed a new method to determine DNA translocation and were able to quantify the efficiency and the rate of packaging. A model for PRD1 DNA packaging was also proposed. Another part of this study covers the lysis of the host cell. As other dsDNA bacteriophages PRD1 has been proposed to utilise a two-component lysis system. The existence of this lysis system in PRD1 has been proven by experiments using recombinant proteins and the multi-step nature of the lysis process has been established.

Characterization of New Viruses from Hypersaline Environments

Viruses of Archaea are the least studied group of viruses. Fewer than 50 archaeal viruses have been reported which constitutes less than one percent of all the isolated prokaryotic viruses. Only about one third of the isolated archaeal viruses infect halophiles. The diversity of haloviruses, virus ecology in highly saline environments and the interactions of haloviruses with their hosts have been little studied. The exiguous knowledge available on halophilic systems is not only due to inadequate sampling but also reflects the extra challenge highly saline systems set on biochemical studies. In this study six new haloviruses were isolated and characterized. Viruses included four archaeal viruses and two bacteriophages. All of the other isolates exhibited head-tail morphology, except SH1 which was the first tailless icosahedral virus isolated from a high salt environment. Production and purification procedures were set up for all of these viruses and they were subjected to stability determinations. Archaeal virus SH1 was studied in more detail. Biochemical studies revealed an internal membrane underneath the protein capsid and a linear dsDNA genome. The overall structure of SH1 resembles phages PRD1, PM2 and Bam35 as well as an archaeal virus STIV. SH1 possesses about 15 structural proteins that form complexes under non-reducing conditions. Quantitative dissociation provided information about the positions of these proteins in the virion. The life cycle of SH1 was also studied. This lytic virus infects Haloarcula hispanica. Adsorption to the host cells is fairly inefficient and the life cycle rather long. Finally, virus responses in a variety of ionic conditions were studied. It was discovered that all of the studied viruses from low salt, marine and high salt environments tolerated larger range of salinities than their bacterial or archaeal hosts. The adsorption efficiency was not determined by the natural environment of a virus. Even though viruses with the slowest binding kinetics were among the haloviruses, fast binders were observed in viruses from all environments. When the salinity was altered, the virus adsorption responses were diverse. Four different behavioral patterns were observed: virus binding increased or decreased in increasing salinity, adsorption maximum was at a particular salt concentration or the salinity did not affect the binding. The way the virus binding was affected did not correlate with the environment, virus morphology or the organism the virus infects.