Near-Infrared Femtosecond Laser for Studying the Strain in Si1-xGex Alloy Films via Second-Harmonic Generation

The second-harmonic generation (SHG) from Si1-xGex alloy films has been investigated by near-infrared femtosecond laser. Recognized by s-out polarized SHG intensity versus rotational angle of sample, the crystal symmetry of the fully strained Si0.83Ge0.17 alloy is found changed from the O-h to the C-2 point group due to the inhomogeneity of the strain. Calibrated by double crystal X-ray diffraction, the strain-induced chi((2)) is estimated at 5.7 x 10(-7) esu. According to the analysis on p-in/s-out SHG, the strain-relaxed Si0.10Ge0.90 alloy film is confirmed to be not fully relaxed, and the remaining strain is quantitatively determined to be around 0.1%.

MULTIPLE PEAK PHOTOLUMINESCENCE OF POROUS SILICON

The photoluminescence (PL) response of porous silicon is usually in the form of a single broad peak. Recently, however, PL response with two peaks has been reported. Here we report the observation of multiple peaks in the PL spectrum of porous silicon. A simple modeling of the line shape indicates that four peaks exist within the response curve, and analysis suggests that the PL of porous silicon is derived from quantum confinement in the silicon crystallites. The line shapes can be due to either minibands within the conduction and valence bands or crystallite size variation or a combination of the two.

New way to enhance the uniformity of self-organized InAs quantum dots

Growth interruption was introduced after the deposition of GaAs cap layer, which is thinner than the mean height of Quantum dots. Uniformity of quantum dots has been enhanced because the full width of half maximum of photoluminescence decrease from 80meV to 27meV in these samples as the interruption time increasing from 0 to 120 second. Meanwhile, we have observed that the peak position of photoluminescence is a function of interruption time. This effect can be used to control the energy level of quantum dots. The phenomena mentioned above can be attributed to the diffusion of In atoms from the top of InAs islands to the top of GaAs cap layer caused by the difference of surface energies between InAs and GaAs.

Dynamic behaviors of mode III interfacial crack under a constant loading rate

In an earlier study on intersonic crack propagation, Gao et al. (J. Mech. Phys. Solids 49: 2113-2132, 2001) described molecular dynamics simulations and continuum analysis of the dynamic behaviors of a mode II dominated crack moving along a weak plane under a constant loading rate. The crack was observed to initiate its motion at a critical time after the onset of loading, at which it is rapidly accelerated to the Rayleigh wave speed and propagates at this speed for a finite time interval until an intersonic daughter crack is nucleated at a peak stress at a finite distance ahead of the original crack tip. The present article aims to analyze this behavior for a mode III crack moving along a bi-material interface subject to a constant loading rate. We begin with a crack in an initially stress-free bi-material subject to a steadily increasing stress. The crack initiates its motion at a critical time governed by the Griffith criterion. After crack initiation, two scenarios of crack propagation are investigated: the first one is that the crack moves at a constant subsonic velocity; the second one is that the crack moves at the lower shear wave speed of the two materials. In the first scenario, the shear stress ahead of the crack tip is singular with exponent -1/2, as expected; in the second scenario, the stress singularity vanishes but a peak stress is found to emerge at a distance ahead of the moving crack tip. In the latter case, a daughter crack supersonic with respect to the softer medium can be expected to emerge ahead of the initial crack once the peak stress reaches the cohesive strength of the interface.

A multi-moment finite volume formulation for shallow water equations on unstructured mesh

A novel and accurate finite volume method has been presented to solve the shallow water equations on unstructured grid in plane geometry. In addition to the volume integrated average (VIA moment) for each mesh cell, the point values (PV moment) defined on cell boundary are also treated as the model variables. The volume integrated average is updated via a finite volume formulation, and thus is numerically conserved, while the point value is computed by a point-wise Riemann solver. The cell-wise local interpolation reconstruction is built based on both the VIA and the PV moments, which results in a scheme of almost third order accuracy. Efforts have also been made to formulate the source term of the bottom topography in a way to balance the numerical flux function to satisfy the so-called C-property. The proposed numerical model is validated by numerical tests in comparison with other methods reported in the literature. (C) 2010 Elsevier Inc. All rights reserved.

A global shallow water model using high order multi-moment constrained finite volume method and icosahedral grid

A novel accurate numerical model for shallow water equations on sphere have been developed by implementing the high order multi-moment constrained finite volume (MCV) method on the icosahedral geodesic grid. High order reconstructions are conducted cell-wisely by making use of the point values as the unknowns distributed within each triangular cell element. The time evolution equations to update the unknowns are derived from a set of constrained conditions for two types of moments, i.e. the point values on the cell boundary edges and the cell-integrated average. The numerical conservation is rigorously guaranteed. in the present model, all unknowns or computational variables are point values and no numerical quadrature is involved, which particularly benefits the computational accuracy and efficiency in handling the spherical geometry, such as coordinate transformation and curved surface. Numerical formulations of third and fourth order accuracy are presented in detail. The proposed numerical model has been validated by widely used benchmark tests and competitive results are obtained. The present numerical framework provides a promising and practical base for further development of atmospheric and oceanic general circulation models. (C) 2009 Elsevier Inc. All rights reserved.

Heat Transfer Problems Induced By Multi-shocks Interaction

Numerical simulations of the multi-shock interactions observable around hypersonic vehicles were carried out by solving Navier-Stokes equations with the AUSMPW scheme and the new type of the IV interaction created by two incident shock waves was investigated in detail. Numerical results show that the intersection point of the second incident shock with the bow shock plays important role on the flow pattern, peak pressures and heat fluxes. In the case of two incident shocks interacting with the bow shock at the same position, the much higher peak pressure and more severe heat transfer rate are induced than the classical IV interaction. The phenomenon is referred to as the multi-shock interaction and higher requirements will be imposed on thermal protection systems.

Study on peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles

The on-way peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles are important data for process safety. Based on carbon monoxide deflagration experiments, the paper presents a multi-zone integration model for calculation of on-way peak overpressure, in which the tube with obstacles is considered as a series of venting explosion enclosures which link each others. The analysis of experimental data indicates that the on-way peak overpressure of gas deflagration can be correlated as an empirical formula with equivalence ratio of carbon monoxide oxidation, expansion ratio, flame path length, etc., and that the on-way peak overpressure exhibits a linear relationship with turbulence factor and flame propagation speed. An empirical formula of flame propagation speed is given.

川西北高寒草甸土壤呼吸研究：季节动态和放牧效应

除植被冠层的光合作用之外，土壤的呼吸作用是陆地生态系统碳收支中最大的通量。土壤呼吸即使发生较小的变化也能显著地减缓或加剧大气中CO2浓度的增加，从而明显影响到全球气候变化。土壤呼吸速率变化与否以及变化的方向可以反映生态系统对环境变化的敏感程度和响应模式。尽管如此，土壤呼吸仍是一个为人们了解不多的生态系统过程。 草地生态系统是陆地生态系统的一个重要组成部分。针对草地土壤呼吸进行野外实验研究和相应方法论的探讨将对区域乃至全球碳源汇性质的准确估算具有重要的科学意义。然而，近几年来关于草地土壤呼吸的主要研究工作都集中在温带草原和部分热带草原，而针对高寒草甸生态系统土壤呼吸的研究报道还很少。 2008年4月至2009年4月期间，我分别在2008年6、8、10、12月和2009年2月和4月分6次对川西北的典型高寒草甸群落的土壤呼吸进行观测，分析了不同类型高寒草甸群落土壤呼吸的季节变化特征以及环境因子和放牧模式对其影响。主要研究结果如下： 1）该地区高寒草甸生态系统在生长季（6月～8月）土壤呼吸速率较大（6.07～9.30μmolCO2¡m-2¡s-1 ） ， 在非生长季（ 12 月～ 2 月） 较小（ 0.16 ～0.49μmolCO2¡m-2¡s-1 ） 。土壤CO2 年累积最大释放量为3963 ～ 5730gCO2¡m-2¡yr-1，其中，生长季土壤CO2的释放量占年总释放量的85%～90%。非生长季占10%～15%。非生长季所占比例略小于冬季积雪覆盖地区的冬季土壤呼吸占年土壤呼吸量的比例（14%～30%）。温度，尤其地温，是影响该地区高寒草甸生态系统土壤呼吸速率的最主要环境因子。土壤呼吸速率与地上生物量和土壤水分之间没有显著相关性，但是土壤含水量过大会导致土壤呼吸速率下降。 2）在观测期内，草丘区的土壤呼吸显著高于对照区的土壤呼吸，其最大土壤呼吸速率为16.77μmolCO2¡m-2¡s-1，土壤CO2 年累积最大释放量为8145gCO2¡m-2¡yr-1，是对照区的近2 倍。由于草丘在高寒草甸中占有较大的面积比例（近30%），因此，它将对高寒草甸生态系统的碳循环起着重要的作用。 3）放牧模式不仅可以影响高寒草甸群落的土壤CO2 排放，而且还可以改变土壤呼吸的温度敏感性（Q10）。本研究表明，在生长季有长期放牧活动干扰时将会增加土壤向大气中释放二氧化碳的速度，促使土壤碳库中碳的流失。禁牧样地的土壤呼吸速率在刚禁牧时先迅速增大，随着禁牧时间的延长土壤呼吸速率将会下降。此外，与其它放牧模式相比，冬季放牧将高寒草甸群落土壤呼吸速率在生长季达到最大值的时间明显向后推迟。不同放牧模式下高寒草甸群落土壤呼吸的Q10 值大小顺序为：禁牧一年群落>冬季放牧群落>禁牧三年群落>夏季放牧群落>自由放牧群落。 4）基于呼吸室技术的观测方法中，测量前的剪草处理可以明显改变该地区高寒草甸群落的土壤温度和土壤呼吸速率。在生长季，剪草处理将使土壤呼吸速率的瞬时响应增加90%左右。由于剪草处理明显增加了剪草样方白天的土壤温度，而土壤温度与土壤呼吸之间存在着极显著的指数相关关系，因而剪草处理导致土壤呼吸速率迅速增加。因此，在高寒地区基于呼吸室技术观测的土壤呼吸应当进行校正。 综上所述，川西北高寒草甸生态系统土壤呼吸速率在生长季较高，而在非生长季较低。土壤温度是影响该地区土壤呼吸的最主要环境因子。在实验观测期，草丘区土壤呼吸速率显著高于对照区的，是对照区土壤呼吸速率的近2倍。由于测量前的剪草处理可以明显改变待测点的土壤呼吸速率，因此，应对在高寒地区基于呼吸室技术观测的土壤呼吸进行校正。 Soil respiration is the second largest component (less than plant phtotosynthesis) of carbon dioxide flux between terrestrial ecosystems and the atmosphere. A minor change in soil respiration rate can significantly slow down or accelerate the increase of atmospheric CO2 concentration that is closely related to global climatic change. In turn, the change in the flux direction and rate of soil respiration may indicate the elasticity and stability of ecosystems to global changes and human disturbance. However, soil respiration is still an ecosystem process that has been poorly understood. Grassland ecosystem is an important component of the terrestrial ecosystem. Accurately estimating the CO2 flux from soil to atmosphere in situ is the key to evaluating the carbon resource and sink regionally or globally. Despite of extensive studies on the temperate and tropic grasslands, the soil respiration of alpine meadows has not substantially been measured. In the current study, soil respiration was measured for an annual cycle from April, 2008 to April, 2009 for the alpine meadow in northwestern Sichuan Province of China to determine the seasonal variation of soil respiration for the typical plant communities. The results are shown as follows: 1) Large seasonal variation of soil respiration was observed in the alpine meadow. The rate of soil respiration was the greatest (6.07～9.30μmolCO2¡m-2¡s-1) in June and the smallest (0.16 ～ 0.49μmolCO2¡m-2¡s-1) occurred from December to February in the non-growing season. The total emission of soil CO2 was estimated as 3963～5730 gCO2¡m-2¡yr-1, 85%~90% of which was released during the growing season, and 10%~15% during the non-growing season which was slightly less than the ratio of winter and annual CO2 flux from soil. Temperature, particularly the soil temperature, was the major environmental factor regulating the soil respiration. Significant and positive relationships were not found between soil respiration and soil moisture and between soil respiration and plant above-ground biomass, but excessive soil water content would decrease in the rate of soil respiration. 2) The rate of soil respiration in grass hummock communities was up to 16.77μmolCO2¡m-2¡s-1, which was about twice as great as in the controls (communities located in low and even sites). Considering the large proportion (about 30% on average) of hummock area in the meadow, it can be concluded that the hummocks played an important role in the carbon cycling of the study ecosystem. 3) Grazing patterns affected the flux of CO2 emission and the temperature sensitivity of soil respiration (Q10) in the alpine meadow. Grazing during growing season increased the rate of soil respiration. The rate of soil respiration increased significantly immediately after the alpine meadow being fenced, but thereafter decreased. In addition, grazing in winter delayed the peak respiration rate relative to the non-grazing mode. The Q10 value was the largest in the non-grazed area for one year, and next came the area with grazing in winter, followed by the non-grazed area for three years, the area with grazing in summer, and the non-limited grazed area. 4) In the chamber-based techniques, clipping manipulation before each measurement increased the transient rate of soil respiration by about 90% in the summer of the alpine meadow. As increase in soil temperature at daytime in the clipped plots by clipping and the exponential relationship between soil respiration and temperature, clipping manipulation led to increase in the rate of soil respiration. This suggested that a correction should be done for the techniques if employed in alpine and cold regions. In summary, the rate of soil respiration in the alpine meadow was the greatest in June and the smallest occurred from ecember to February in the non-growing season. Soil temperature was the major environmental factor regulating the soil respiration. The rate of soil respiration in grass hummock communities was up to 16.77μmolCO2¡m-2¡s-1, which was about twice as great as in the controls. A correction should be done for the techniques if employed in alpine and cold regions, because of the effect of clipping manipulation on soil temperature and respiration.