A 10-GHz Bandwidth Electroabsorption Modulated Laser by Ultra-Low-Pressure Selective Area Growth

A novel integration technique has been developed using band-gap energy control of InGaAsP/InGaAsP multiquantum-well (MQW) structures during simultaneous ultra-low-pressure (22 mbar) selective-area-growth (SAG) process in metal-organic chemical vapour deposition. A fundamental study of the controllability of band gap energy by the SAG method is performed. A large band-gap photoluminescence wavelength shift of 83nm is obtained with a small mask width variation (0-30μm). The method is then applied to fabricate an MQW distributed-feedback laser monolithically integrated with an electroabsorption modulator. The experimental results exhibit superior device characteristics with low threshold of 19mA, over 24 dB extinction ratio when coupled into a single mode fibre. More than 10 GHz modulation bandwidth is also achieved, which demonstrates that the ultra-low-pressure SAG technique is a promising approach for high-speed transmission photonic integrated circuits.

A double wavelength DFB laser with an identical active area for CWDM

A novel distribute feedback (DFB) laser which gave two different wavelengths under two distinct work conditions was fabricated. The laser consists of two Bragg gratings with different periods corresponding to wavelength spacing of 20 nm in an identical active area. When driving current was injected into one of the different sections separately, two different wavelengths at 1542.4 and 1562.5 nm were realized. The side mode suppression ratio (SMSR) of 45 dB or more both for the two Bragg wavelengths were achieved. The fabricating process of the laser was just the same as that of traditional DFB laser diode. This device can be potentially used in coarse wavelength division multiplexer (CWDM) as a promising light source and the technology idea can be used to enlarge the transmission capacity in metro area network (MAN).

Selective Area Growth InGaAsP by MOVPE

The wide stripe (ISjum) selective area growth (SAG) of InGaAsP by low pressure MOVPE is systematically investigated. The characteristics of the growth ratios,thickness enhancement factors .bandgap modulation,and composition modulation vary with the growth conditions such as mask width,growth pressure. Flux of III-group precursors are outlined and the rational mechanism behind SAG MOVPE is explained. In addition,the surface spike of the SAG InGaAsP is shown and the course of it is given by the variation of V /III .

1.5μm Self-Aligned Spotsize Converter Integrated DFB Fabricated by Selective Area Grown MOVPE

High performance 1.57μm spotsize converter monolithically integrated DFB is fabricated by the technique of self-aligned selective area growth. The upper optical confinement layer and the butt-coupled tapered thickness waveguide are regrown simultaneously, which not only offeres the separated optimization of the active region and the integrated spotsize converter, but also reduces the difficulty of the butt-joint selective regrowth. The threshold current is as low as 4.4mA. The output power at 49mA is 10.1mW. The side mode suppression ratio (SMSR) is 33.2dB. The vertical and horizontal far field divergence angles are as small as 9° and 15° respectively, the 1dB misalignment tolerance are 3.6μm and 3.4μm.

Spotsize Converter Integrated DFB Laser Diode Using Selective Area Growth of MOCVD

The characteristics of thickness enhancement factor and bandgap wavelength of selectively grown In-GaAsP are investigated. A high thickness enhancement factor of 2.9 is obtained. Spotsize converter integrated DFB lasers are fabricated by using the technique of SAG. The threshold current is as low as 10.8mA. The output power is 10m W at 60mA without coating and the SMSR is 35.8dB. The vertical far field angle (FWHM) is decreased from 34 °to 9 °. The tolerance of 1dBm misalignment is 3.4μm vertically.

Monolithic Integration of DFB Laser Diode and Electroabsorption Modulator by Selective Area Growth Technology

国家863计划

Multi-Wavelength InGaAsP Lasers Grown by LP-MOCVD Selective Area Growth

国家863计划

Microorganisms linked to Neoproterozoic microspar carbonate sedimentation in the Jilin-Liaoning area

Molar-tooth carbonate refers to a sort of rock that has ptygmatical folded structure comparable to the ivory. This kind of carbonate exists in a special time range (from Middle to Neoproterozoic). Its origin and the possibility to use it in stratigraphic correlation of the paleocontinent is the key task of the IGCP447, a project on Proterozoic molar tooth carbonates and the evolution of the earth (2001-2005). The importance lies in that the molar-tooth structure is the key to solving problems related to Precambrian biological and global geochemical events. The molar-tooth structure is associated with microorganisms. Development and recession of such carbonates have relations with the evolution process of early lives and abrupt changes in sea carbonate geochemistry. In recent years, based on researches on petrology, geochemistry and Sr isotope of molar-tooth carbonate in the Jilin-Liaoning and Xuzhou-Huaiyang area, the authors hold that it can be used as a marker for stratigraphic sequence and sedimentary facies analyses.