Heterojunction solar cells with n-type nanocrystalline silicon emitters on p-type c-Si wafers

Hydrogenated nanocrystalline silicon (nc-Si:H) n-layers have been used to prepare heterojunction solar cells on flat p-type crystalline silicon (c-Si) wafers. The nc-Si:H n-layers were deposited by radio-frequency (RF) plasma enhanced chemical vapor deposition (PECVD), and characterized using Raman spectroscopy, optical transmittance and activation energy of dark-conductivity. The nc-Si:H n-layers obtained comprise fine grained nanocrystallites embedded in amorphous matrix, which have a wider bandgap and a smaller activation energy. Heterojunction solar cells incorporated with the nc-Si n-layer were fabricated using configuration of Ag (100 nm)/1T0 (80 nm)/n-nc-Si:H (15 nm)/buffer a-Si:H/p-c-Si (300 mu m)/Al (200 nm), where a very thin intrinsic a-Si:H buffer layer was used to passivate the p-c-Si surface, followed by a hydrogen plasma treatment prior to the deposition of the thin nanocrystalline layer. The results show that heterojunction solar cells subjected to these surface treatments exhibit a remarkable increase in the efficiency, up to 14.1% on an area of 2.43 cm(2). (c) 2006 Elsevier B.V. All rights reserved.

Growth and characterization of 0.8-mu m gate length AlGaN/GaN HEMTs on sapphire substrates

AlGaN/GaN high electron mobility transistor (HEMT) structures were grown on 2 inch sapphire substrates by MOCVD, and 0.8-mu m gate length devices were fabricated and measured. It is shown by resistance mapping that the HEMT structures have an average sheet resistance of approximately 380 Omega/sq with a uniformity of more than 96%. The 1-mm gate width devices using the materials yielded a pulsed drain current of 784 mA/mm at V-gs=0.5 V and V-ds=7 V with an extrinsic transconductance of 200 mS/mm. A 20-GHz unity current gain cutoff frequency (f(T)) and a 28-GHz maximum oscillation frequency (f(max)) were obtained. The device with a 0.6-mm gate width yielded a total output power of 2.0 W/mm (power density of 3.33 W/mm) with 41% power added efficiency (PAE) at 4 GHz.

Structural and optical characterization of Zn1-xCdxO thin films deposited by dc reactive magnetron sputtering

Zn1-xCdxO crystal thin films with different compositions were prepared on silicon and sapphire substrates by the dc reactive magnetron sputtering technique. X-ray diffraction measurements show that the Zn1-xCdxO films are of completely (002)-preferred orientation for x less than or equal to 0.6. For x = 0.8, the Elm is a mixture of ZnO hexagonal wurtzite crystals and CdO cubic crystals. For pure CdO, it is highly (200) preferential-oriented. Photoluminescence spectrum measurement shows that the Zn1-xCdxO (x = 0.2) thin film has a redshift of 0.14 eV from that of ZnO reported previously.

Ultrafast low-temperature grown AlGaAs/GaAs photorefractive quantum wells using point defects as capture centers

At a medium substrate temperature of 400 degrees C and a lower As flux, we have grown an ultrafast AlGaAs/GaAs photorefractive multiple quantum well (MQW) structure by molecular beam epitaxy. The as-grown sample exhibits strong photorefractive effect under the transverse Frantz-Keldysh geometry. A peak electroabsorption of 2100 cm(-1) is measured in the as-grown sample in an 11 kV/cm dc electric field, and the peak photorefractive diffraction efficiency can be 1.2%. After postgrowth annealing, the photorefractive effect becomes weak and disappears in samples annealed above 700 degrees C. Using optical transient current spectroscopy, deep levels are measured in these samples. It is found that deep levels are stable against annealing until 700 degrees C. Using a pump-probe technique, carrier lifetimes are measured at room temperature. We find that the as-grown sample has a lifetime of 20 ps, while the 700 degrees C annealed sample has a lifetime of more than 200 ps. The ultrafast lifetime in the as-grown sample is caused by point defects, not by As clusters. Our result show that AlGaAs/GaAs MQW structure grown around 400 degrees C has better performance of the photorefractive effect. (C) 1999 American Institute of Physics. [S0003-6951(99)04036-X].

中国材料工程大典—信息功能材料工程

本书是《中国材料工程大典》中的卷目之一。 信息功能材料是信息科学技术和信息产业发展的基础和先导。21世纪将是以信息产业为核心的知识经济时代，对信息技术和信息资源的竞争将更加激烈。我国电子信息行业2004年完成产品销售收入达26500亿元，多年来已居外贸出口首位，并继续以高出工业发展速度10％的速度发展，已成为世界信息产业大国。加快由信息产业大国向信息产业强国迈进的步伐，是我们广大从事信息技术，特别是信息功能材料工作者义不容辞的责任。希望《中国材料工程大典》中《信息功能材料工程》卷的出版，将有力推动我国信息技术和信息产业的健康发展。 《信息功能材料工程》分上、中、下卷，共设20篇，约600万字。它涉及到信息的获取、传输、存储、显示和处理等主要技术用的材料与器件，是目前我国该领域比较完整的专业工具书。参加这部书编写的有中科院、高校和部分企业的专家教授近200名。参加编写的主要单位有中科院半导体研究所、中科院物理研究所、中科院微电子研究所、中科院上海精密光学机械研究所、中科院上海红外技术物理研究所、中科院长春应用化学研究所、中科院合肥固体物理所、南京大学、清华大学、西安理工大学、北京有色金属研究总院、武汉邮电科学研究院等。历时近3年完稿。由王占国、陈立泉、屠海令任主编并统稿。 本卷各篇不仅全面系统地反映了国外信息功能材料研究领域的现状、最新进展和发展趋势，而且也特别注重我国在该领域的研发和产业化方面取得的成果，力图使其具有实用性、先进性和权威性。本书适合于从事信息功能材料的科研工作者和工程技术人员查阅使用，也可供有关师生参考。

Heterojunction solar cells with n-type nanocrystalline silicon emitters on p-type c-Si wafers

Hydrogenated nanocrystalline silicon (nc-Si:H) n-layers have been used to prepare heterojunction solar cells on flat p-type crystalline silicon (c-Si) wafers. The nc-Si:H n-layers were deposited by radio-frequency (RF) plasma enhanced chemical vapor deposition (PECVD), and characterized using Raman spectroscopy, optical transmittance and activation energy of dark-conductivity. The nc-Si:H n-layers obtained comprise fine grained nanocrystallites embedded in amorphous matrix, which have a wider bandgap and a smaller activation energy. Heterojunction solar cells incorporated with the nc-Si n-layer were fabricated using configuration of Ag (100 nm)/1T0 (80 nm)/n-nc-Si:H (15 nm)/buffer a-Si:H/p-c-Si (300 mu m)/Al (200 nm), where a very thin intrinsic a-Si:H buffer layer was used to passivate the p-c-Si surface, followed by a hydrogen plasma treatment prior to the deposition of the thin nanocrystalline layer. The results show that heterojunction solar cells subjected to these surface treatments exhibit a remarkable increase in the efficiency, up to 14.1% on an area of 2.43 cm(2). (c) 2006 Elsevier B.V. All rights reserved.

Selective and lithography-independent fabrication of 20 nm nano-gap electrodes and nano-channels for nanoelectrofluidics applications

A new method has been developed to selectively fabricate nano-gap electrodes and nano-channels by conventional lithography. Based on a sacrificial spacer process, we have successfully obtained sub-100-nm nano-gap electrodes and nano-channels and further reduced the dimensions to 20 nm by shrinking the sacrificial spacer size. Our method shows good selectivity between nano-gap electrodes and nano-channels due to different sacrificial spacer etch conditions. There is no length limit for the nano-gap electrode and the nano-channel. The method reported in this paper also allows for wafer scale fabrication, high throughput, low cost, and good compatibility with modern semiconductor technology.

A 20.1 W Solid-State Laser Pumped by 887 nm with High Efficiency and TEM00 Mode

High efficiency, TEM00 mode, high repetition rate laser pumped by 887 nm is reported. 20.1 W output laser emitting at 1064 nm is achieved in a 0.3 at % Nd-doped Nd:YVO4, which absorbs pumping light of 30.7 W at 887 nm. The opto-optic efficiency and the slope efficiency are 65.5 and 88.5%, respectively. The stable Q-switching operation worked well at 100 kHz and the beam quality is near diffraction-limit with M-2 factor measured as M-2 approximate to 1.2. And the pulse waveform is analyzed in this paper.

Geomagnetic paleointensity dating of South China Sea sediments for the last 130 kyr

Relative paleointensity records from the northern South China Sea, northwest Pacific Ocean were studied in two gravity piston cores. Continuous mineral magnetic and paleomagnetic measurements were made using discrete sediment samples. Detailed rock magnetic parameters, such as thermomagnetic and high-field hysteresis data, indicate that pseudo-single domain magnetite in a narrow range of grain-size and concentration is the main contributor to the remanent magnetization. The uniform magnetic mineralogy meets the commonly accepted criteria for establishing relative paleointensity records. The relative paleointensity (RPI) curves were constructed by normalizing the natural remanent magnetization (NRM) with isothermal remanent magnetization (IRM), both in the 20-60 mT demagnetization state. Dating constraints have been provided by radiocarbon ages in the upper 400 cm of both cores. Furthermore, we have correlated our paleointensity records with NAPIS-75, S.Atlantic-1089, Sint-200 and NOPAPIS-250 to determine the chronological RPI framework for the South China Sea (SCS-PIS). Although some temporal offsets of paleointensity features between the different records have been recognized, their similar shape suggests that relative paleointensity on the 10(3)-10(4) year scale is globally coherent and can provide an age framework for sediments independent of delta O-18 ages.

Methane hydrate growth velocity in seepage system of Qiongdongnan Basin, South China Sea

The occurrences of diapirs, gas-filled zones and gas plumes in seawater in Qiongdongnan Basin of South China Sea indicate that there may exist seepage system gas-hydrate reservoirs. Assuming there has a methane venting zone of 1500 m in diameter, and the methane flux is 1000 kmol/a, and the temperature of methane hydrate-bearing sediments ranges from 3 degrees C to 20 degrees C, then according to the hydrate film growth theory, by numerical simulation, this paper computes the temperatures and velocities in 0 mbsf, 100 mbsf, 200 mbsf, 425 mbsf over discrete length, and gives the change charts. The results show that the cementation velocity in sediments matrix of methane hydrate is about 0.2 nm/s, and the seepage system will evolve into diffusion system over probably 35000 years. Meanwhile, the methane hydrate growth velocity in leakage system is 20 similar to 40 times faster than in diffusion system.

Yb3+-doped 200 mu m diameter core, gain guided index-antiguided fiber

The lasing in an end-pumped gain guided index-antiguided (GG-IAG) Yb3+-doped silicate glass fiber with a 200 mu m diameter core is demonstrated. Laser beams with similar beam propagation factors M (2) and mode field diameters W (0) (> 160 mu m) were observed at the output end of the GG-IAG fibers under different pump powers, which indicated that single mode behavior and excellent beam quality were achieved during propagation. Furthermore, the laser amplifier characteristics in the present Yb3+-doped GG-IAG fiber were also evaluated.

地肤根系的力学性质及对道路侵蚀的影响

基于黄土高原植物路防蚀对适宜植物的需要,对多年生草本植物地肤根系的抗剪切强度进行了测试,并在野外生长有地肤坡面的径流小区进行了冲刷试验。结果表明:相同试验条件下含有单株地肤根系的土样比不含地肤根系的土样,在100、200、300、400 kPa共4种不同垂直荷载压力下,其抗剪切强度分别提高了9.51%、14.42%、17.03%、7.35%;坡面冲刷单宽流量为1.67×10-4m3/(s.m)且坡面地肤覆盖度为0、20%、40%、60%、80%时,裸坡的侵蚀量分别是地肤坡面的2、7、12倍及29倍左右,这说明地肤对于提高土壤抗侵蚀性能有显著效果,是一种适宜栽培于黄土高原道路的植被品种。

黄土高原丘陵沟壑区不同土地利用模式对土壤氮素淋溶的影响

通过对黄土高原丘陵沟壑区不同土地利用模式土壤剖面NO-3-N、NH+4-N、有机质和全氮分布的测定,论述黄土高原丘陵沟壑区不同土地利用模式对土壤氮素淋溶的影响,对当地农业发展提出建议。结果表明:在200 cm内土壤NO-3-N最大值都出现在200 cm处,其中日光温室最大为20.36 mg/kg。土壤NH+4-N在200 cm内是较均匀的分布在10~25 mg/kg。不同土地利用模式对土壤剖面土壤NH+4-N、有机质和全氮分布没有影响。随着深度的变化对土壤NH+4-N分布也没有影响。土壤有机质和全氮在土壤剖面的分布是,随着深度的增加而减少,60 cm以下有机质保持在1.07~5.95 g/kg,全氮保持在0.12~0.35 g/kg。根据试验结果得出,土壤氮素淋溶的主要成分是NO-3-N,土壤NO-3-N淋溶程度与降雨、灌溉、施肥量呈正比,在坡地的淋溶较少。