Depth dependence of the tetragonal distortion of a GaN layer on Si(111) studied by Rutherford backscattering/channeling

Rutherford backscattering and channeling have been used to characterize the structure of a GaN layer grown on a Si(111) substrate. The results show that a 1.26 mum GaN epitaxial layer with a rather abrupt interface and a good crystalline quality (chi(min)=3.4%) can be grown on a Si(111) substrate. Using the channeling angular scan around an off-normal <1 (2) over bar 13> axis in the {10 (1) over bar0} plane of the GaN layer, the tetragonal distortion e(T), which is caused by the elastic strain in the epilayer, can be determined. Moreover, the depth dependence of the e(T) can be obtained using this technique. A fully relaxed (e(T)=0) GaN layer for a thickness <2.8 mum is expected. (C) 2002 American Institute of Physics.

Comprehensive analysis of microtwins in the 3C-SiC films on Si(001) substrates

Microtwins in the 3C-SiC films grown on Si(0 0 1) by atmosphere pressure chemical vapor deposition (APCVD) were investigated in detail using X-ray four-circle diffractometry. The Phi scan shows that 3C-SiC films can grow on Si substrates epitaxially and epitaxial relationship is revealed as (0 0 1)(3C) (SiC)parallel to (0 0 1)(Si),[1 1 1](3C-SiC)parallel to [1 1 1](Si). Other diffraction peaks at about 15.8 degrees in x emerged in the pole figures of the (I 1 1) 3C-SiC. We performed the pole figure of (1 0 (1) over bar 0)h-SiC and the reciprocal space mapping from the (1 1 1) reciprocal lattice point of base SiC to the (0 0 2) point of microtwin for the first time, indicating that the diffraction peaks at 15.8 degrees in x result from not hexagonal SiC but microtwins of 3C-SiC, and twin inclusions are estimated to be around 1%. (C) 2001 Published by Elsevier Science B.V.

Investigation of {111}A and {111} planes of c-GaN epilayers grown on GaAs(001) by MOCVD

A determination of {1 1 1}A and {1 1 1}B in cubic GaN(c-GaN) was investigated by X-ray diffraction technique in detail. The c-GaN films are grown on GaAs(0 0 1) substrates by metalorganic chemical vapor deposition(MOCVD). The difference of integrated intensities measured by omega scan for the different order diffractions from {1 1 1}A and {1 1 1}B planes in the four-circle diffractometer gives convincing evidence as to which is the {1 1 1}A and which is the {1 1 1}B planes. The lesser deviation between the ratios of /F-h k l/(2)//F-(h) over bar (k) over bar (l) over bar/(2) and the calculated values after dispersion correction for atomic scattering factor shows that the content of parasitic hexagonal GaN(h-GaN) grown on c-GaN{1 1 1}A planes is higher than that on {1 1 1}B planes. The reciprocal space mappings provide additional proof that the h-GaN inclusions in c-GaN films appear as lamellar structure. (C) 2001 Published by Elsevier Science B.V.

Microtwins and twin inclusions in the 3C-SiC epilayers grown on Si(001) by APCVD

Microtwins in the 3C-SiC films grown on Si(001) by APCVD were analyzed in detail using an X-ray four-circle diffractometer. The empty set scan shows that 3C-SiC films can grow on Si substrates epitaxially and the epitaxial relationship is revealed as (001)(3C-SiC)//(001)(Si), [111](3C-SiC)//[111](Si). Other diffractions emerged in the pole figures of the (111) 3C-SiC. We performed the (10 (1) over bar0) h-SiC and the reciprocal space mapping of the (002) plane of twins for the first time, finding that the diffractions at chi = 15.8 degrees result from not hexagonal SiC but microtwins of 3C-SiC, and twin inclusions are estimated to be 1%.

Analysis of atomic force microscopic results of InAs islands formed by molecular beam epitaxy

Atomic force microscopy (AFM) measurements of nanometer-sized islands formed by 2 monolayers of InAs by molecular beam epitaxy have been carried out and the scan line of individual islands was extracted from raw AFM data for investigation. It is found that the base widths of nanometer-sized islands obtained by AFM are not reliable due to the finite size and shape of the contacting probe. A simple model is proposed to analyze the deviation of the measured value From the real value of the base width of InAs islands. (C) 1998 Elsevier Science B.V. All rights reserved.

AlGaN/GaN/InGaN/GaN DH-HEMTs structure with an AlN interlayer grown by MOCVD

A novel AlGaN/GaN/GaN/GaN double heterojunction high electron mobility transistors (DH-HEMTS) structure with an AlN interlayer on sapphire substrate has been grown by MOCVD. The structure featured a 6-10 nm In0.1Ga0.9N layer inserted between the GaN channel and GaN buffer. And wer also inserted one ultrathin. AlN interlayer into the Al/GaN/GaN interface, which significantly enhanced the mobility of two-dimensional electron gas (2DEG) existed in the GaN channel. AFM result of this structure shows a good surface morphology and a low dislocation density, with the root-mean-square roughness (RMS) of 0.196 nm for a scan area of 5 mu m x 5 mu m. Temperature dependent Hall measurement was performed on this sample, and a mobility as high as 1950 cm(2)/Vs at room temperature (RT) was obtained. The sheet carrier density was 9.89 x10(12) cm(2), and average sheet resistance of 327 Omega/sq was achieved. The mobility obtained in this paper is about 50% higher than other results of similar structures which have been reported. (c) 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

AlGaN/AlN/GaN/InGaN/GaN DH-HEMTs with improved mobility grown by MOCVD

AlGaN/AlN/GaN/InGaN/GaN double heterojunction high electron mobility transistors (DH-HEMTs) structures with improved buffer isolation have been investigated. The structures were grown by MOCVD on sapphire substrate. AFM result of this structure shows a good surface morphology with the root-mean-square roughness (RMS) of 0.196 nm for a scan area of 5 mu mx5 mu m. A mobility as high as 1950 cm(2)/Vs with the sheet carrier density of 9.89x10(12) cm(-2) was obtained, which was about 50% higher than other results of similar structures which have been reported. Average sheet resistance of 327 Omega/sq was achieved. The HEMTs device using the materials was fabricated, and a maximum drain current density of 718.5 mA/mm, an extrinsic transconductance of 248 mS/mm, a current gain cutoff frequency of 16 GHz and a maximum frequency of oscillation 35 GHz were achieved.

Enhanced fiber Bragg grating sensor demodulation technique using cascade wavelength division multiplex couplers

An enhanced technique for interrogating fiber Bragg grating wavelength shift using cascade wavelength division multiplexer (WDM) couplers was proposed and demonstrated. Three WDM couplers which show a linear filter function over the expected wavelength range are employed and cascaded to track Bragg wavelength shifts. Compared with single WDM demodulator. sharper spectral slope is obtained and considerable linear filter range is kept. The static and dynamic strain sensor demodulation experiments demonstrated that the simple passive technique improves the sensitivity approximately two times and keeps 5nm linear demodulation range based on our devices. The cascade WDM coupler demodulation system has high scan rate which can be used to monitor fast vibration.

Design for an IO block array in a tile-based FPGA

A design for an IO block array in a tile-based FPGA is presented.Corresponding with the characteristics of the FPGA, each IO cell is composed of a signal path, local routing pool and configurable input/output buffers.Shared programmable registers in the signal path can be configured for the function of JTAG, without specific boundary scan registers/latches, saving layout area.The local routing pool increases the flexibility of routing and the routability of the whole FPGA.An auxiliary power supply is adopted to increase the performance of the IO buffers at different configured IO standards.The organization of the IO block array is described in an architecture description file, from which the array layout can be accomplished through use of an automated layout assembly tool.This design strategy facilitates the design of FPGAs with different capacities or architectures in an FPGA family series.The bond-out schemes of the same FPGA chip in different packages are also considered.The layout is based on SMIC 0.13μm logic 1P8M salicide 1.2/2.5 V CMOS technology.Our performance is comparable with commercial SRAM-based FPGAs which use a similar process.

An All-E-Beam Lithography Process for the Patterning of 2D Photonic Crystal Waveguide Devices

We present an all-e-beam lithography (EBL) process for the patterning of photonic crystal waveguides.The whole device structures are exposed in two steps. Holes constituting the photonic crystal lattice and defects are first exposed with a small exposure step size (less than 10nm). With the introduction of the additional proximity effect to compensate the original proximity effect, the shape, size, and position of the holes can be well controlled.The second step is the exposure of the access waveguides at a larger step size (about 30nm) to improve the scan speed of the EBL. The influence of write-field stitching error can be alleviated by replacing the original waveguides with tapered waveguides at the joint of adjacent write-fields. It is found experimentally that a higher exposure efficiency is achieved with a larger step size;however,a larger step size requires a higher dose.

MOCVD-Grown AlGaN/AlN/GaN HEMT Structure with High Mobility GaN Thin Layer as Channel on SiC

AlGaN/AlN/GaN high electron mobility transistor (HEMT) structures with a high-mobility GaN thin layer as a channel are grown on high resistive 6H-SiC substrates by metalorganic chemical vapor deposition. The HEMT structure exhibits a typical two-dimensional electron gas (2DEG) mobility of 1944cm2/(V · s) at room temperature and 11588cm2/(V· s) at 80K with almost equal 2DEG concentrations of about 1.03 × 1013 cm-2 High crystal quality of the HEMT structures is confirmed by triple-crystal X-ray diffraction analysis. Atomic force microscopy measurements reveal a smooth AlGaN surface with a root-mean-square roughness of 0. 27nm for a scan area of 10μm × 10μm. HEMT devices with 0.8μm gate length and 1.2mm gate width are fabricated using the structures. A maximum drain current density of 957mA/mm and an extrinsic transconductance of 267mS/mm are obtained.

两种银莲花属植物的化学成分研究

本学位论文由5 章组成。第1 章报道了两头尖中三萜皂苷类化合物的全扫描电喷雾多级质谱分析及银莲花素A 的电喷雾质谱裂解规律；第2 和3 章报道了两种银莲花属药用植物化学成分的研究结果；第4 章报道了银莲花素A 的化学结构修饰及其对一种蛋白酪氨酸磷酸酯酶（PTP-1B）的抑制活性；第5 章综述了电喷雾质谱在皂苷类化合物结构鉴定中的应用进展。 第1 章报道了运用全扫描电喷雾多级质谱对两头尖中三萜皂苷类化合物的快速定性检测，共检测出18 个准分子离子峰，根据多级质谱数据并结合文献报道，对其中的15 个准分子离子峰进行了归属，并区分了一些同分异构体；更有意思的是，发现了3 个未见文献报道的三萜皂苷类化合物。根据它们的多级质谱数据，对其结构分别进行了初步解析。本章同时对银莲花素A 特殊的质谱裂解途径通过衍生物制备及其质谱分析进行了确认。 第2 和3 章，分别报道了两头尖和打破碗花花中水溶性多糖苷的分离纯化和结构鉴定。采用D101 大孔树脂和反复硅胶柱层析等分离手段，从两头尖水溶性部分分离得到8 个三萜皂苷类化合物，通过红外、电喷雾质谱和核磁共振等现代谱学方法，并结合传统的化学手段鉴定了它们的结构，其中4 个化合物为新化合物，分别命名为多被银莲花皂苷19、多被银莲花皂苷20、多被银莲花皂苷21和多被银莲花皂苷22。从打破碗花花水溶性部位分离得到6 个三萜皂苷类化合物，通过现代谱学手段，并结合传统的化学方法对它们进行了鉴定，其中1 个为新化合物，命名为打破碗花花苷H。 第4 章报道了以银莲花素A 及其同系物为先导化合物，进行化学结构修饰并对修饰产物进行广泛的生物活性筛选，发现在银莲花素A 及其同系物的结构中引入一些酸性基团后，其生物活性发生了变化，一些修饰产物显示出很强的PTP-1B 抑制作用，提示这些化合物有可能用于治疗II 型糖尿病。 第5 章综述了电喷雾多级质谱用于皂苷类化合物结构鉴定的研究进展。 This dissertation composes of five chapters. The first chapter elaborates the detection and qualification of the triterpenoidal saponins in Anemone raddeana by positive and negative full scan ESI-MSn. This part also reports the special fragmentation pathway of Raddeanin A by ESI-MS/MS. The second and third chapters present the phytochemical investigation of two medicinal plants from Anemone. The fourth part dwells on the structure modification of Raddeanin A and their inhibitory activity against PTP-1B. The last part is a review on the progress in the application of ESI-MSn in the structure identification of saponins. The first chapter reports the application of full scan ESI-MSn for fast analysis of triterpenoid saponins in Anemone raddeana. Eighteen quasi- molecular ion peaks were detected in the positive full scan ESI-MS and fifteen of them were identified by analysis of their tandem mass spectral data in the negative ion mode. Several isomers were differentiated. More interesting, three unreported triterpenoid saponins in this medicinal plant were detected and their structures were deduced according to the dissociation pathway of the known triterpenoidal saponins. This chapter also confirms the special fragmentation pathway of Raddeanin A by its derivative and the mass spectral analysis. The second and third chapters expatiate on the isolation and identification of the chemical constituents from A. raddeana and A. hupehensis. Eight compounds were isolated from the roots and stems of A. raddeana by methanol extraction and repeated column chromatography (including D101 and silica gel), and their structures were determined on the basis of IR, ESI-MS, NMR and chemical methods (including acid hydrolysis and alkaline saponification). Among them, four are new triterpenoid saponins and named as Raddeanoside R19, Raddeanoside R20, Raddeanoside R21 and Raddeanoside R22. Six compounds were isolated from the whole plants of A. hupehensis by the same methods as above, and their structures were also determined with the same way. One of them was confirmed to be new triterpenoid saponins and named as hupehensis saponin H. In the fourth chapter, in order to look for new active compounds, the structure of Raddeanin A and its analogs were modified. It was found that the modified products exhibited obvious inhibitory activity against PTP-1B when several acid groups were introduced. The fifth chapter summarizes the progress on the application of ESI-MSn in the structure identification of saponins.

自养氨氧化混合种群特性和共存机理初步研究

组特殊自养氨氧化混合种群，表现：无机环境种群生长迅速、生物量高；在一个完全无机的自养生长环境中，不仅保持高氨氧化速率，并出现丰富的异养微生物种群；该种群置于异养、厌氧环境中，迅速表现出产氢特征。对于这样一个特殊的生态体系，研究其共生机理，以及联接这些种群之间的碳源和能源问题，将具有非常重要意义。我们拟从种群特征、细胞表面分泌产物、游离体系产物多糖、蛋白和脂肪酸方面开展研究。 第一部分，自养氨氧化混合种群的基本特征。采用氨氧化培养基，进行种群氨氧化特征研究；采用扫描电镜观察自养混合种群的微观特征；沉降、离心去除微生物种群，分析水相中的总有机碳、糖类等物质；利用LB培养基进行种群的分离、纯化，并采用DGGE手段对微生物种群结构进行分析。结果表明，接入菌种后（2/5000（V/V）），培养液中氨（200mg/L）在3－5天内快速降解；亚硝酸盐与氨氮变化呈负相关趋势，仅有少量硝酸盐含量（< 30mg/L）。氨氧化种群的生物量增长与氨氧化趋势一致，初始生物量7.75 mg/L(蛋白含量)，3-5天后生物量快速增长，并达到最高63.06 mg/L（蛋白含量）。电镜图片显示，种群外包裹一层粘液。离心除去菌体后，检测培养液总有机碳和糖的含量，同样表现出与生物量增长相似的特征，分别由初始的3.73、2.35 mg/L，3－5内天迅速增加，并分别达到最大值35.19、27.45 mg/L。经初步分离、纯化并对纯化菌株进行测序，获得了10株异养微生物分别为布鲁氏菌科苍白杆菌属、纤维单孢菌、类芽孢菌属、黄杆菌属、无色杆菌、鞘脂单胞菌、嗜麦芽寡养单胞菌、噬氢菌属、硫红球菌、假单胞菌；DGGE显示，约有20分条离带，我们对其中的两条优势条带进行切割回收测序，鉴定为欧洲亚硝化单胞菌（Nitrosomonas eur）。 第二部分：混合种群自养-异养菌共生的可能机制。在对微生物种群特征初步分析基础上，针对胞外糖类组分可能被微生物代谢分解，我们重点对微生物细胞蛋白质与糖类进行分析。采用超声结合RIPA裂解液裂解，SDS-PAGE电泳分析混合种群总蛋白种类，并通过氨基酸分析仪及红外光谱法分析氨基酸组成及蛋白红外特征。采用超声破碎结合反复冻融对细胞样品进行处理，提取液采用醇沉、Sevage脱氮白，凝胶过滤方法脱盐和分级分离。对提取物的糖分析包括：紫外扫描，红外光谱，核磁共振，单糖组成分析；扫描电镜观察菌群破裂现象。SDS-PAGE分析结果表明：氨氧化种群不同生长阶段都显示出42kD蛋白表达量很高，d4时42kD蛋白表达已经很强，4-7d内一直持续这种过量表达，直到d8后表达开始减弱。说明42kD蛋白可能与氨氧化密切相关。红外光谱分析显示：细胞提取物的特征峰分布在3427.42cm-1、1718.18 cm-1和1681.72 cm-1、1160.07和1086.74 cm-1，分别对应为OH、 C=O、C－O－C基团，表明具有蛋白的典型特征；氨基酸分析显示蛋白中的Gly,Asp,Ala,Glu含量相对较高。 提取物中胞外多糖分离谱图得到不均一组分，共得到6个收集峰；紫外扫描在201－213 nm处有多糖吸收峰，同样表明多糖成分不均一性；多糖红外光谱特征峰主要分别在3400.49 cm-1、2920.28 cm-1、1154.54和1087.52 cm-1，对应OH、－CH2－ or CH 、C－O－H or C－O－C等多糖特征基团；多糖提取物核磁共振1H d4.3～5.9之间出现强吸收峰，这是1H中，多糖存在的明显证据，1H NMR中，其中O-乙酰基的甲基上的氢信号为d1.1～1.3之间。糖肟全苯甲酸酯衍生物的HPLC测定中，得到单一的单糖峰，由于时间问题，还未进行更深入的试验；电镜图片显示，种群中的细胞有大量的破裂现象。 实验表明，自养氨氧化混合种群显示出快速的氨氧化速率，氨氧化过程生物量和有机质的增加明显。微生物种群包裹粘液层，并分离纯化出大量的异养菌；去除菌体后的游离培养液中存在有机质（包括多糖）说明无机自养生长体系中存在异养菌生长、繁殖的二次碳源；细胞提取物中蛋白条带数目多、种类丰富；细胞多糖提取物具有明显的多糖特征，以及单糖的存在。结合种群的显微特征和游离体系中的有机质的检测结果，我们认为，无机自养生长体系中，种群细胞生长过程中发生的破裂现象可能是导致大量的蛋白、多糖释放到游离胞外，并成为其他异养菌生长的碳源和氮源。这可能是自养体系中，大量异养菌共生的可能机制，至于是什么原因引起种群生长过程中产生的破裂现象，还有待下一步深入研究。 A group of mixed autotrophic ammonia oxidizing populations, having much biological characteristic tested by concerned personnel for pilot test: Performed rapid population growth and obtained high biomass in inorganic environment; Not only maintained a high rate of ammoxidation, promoted a wealth of heterotrophic microbial populations growth in a totally inorganic and autotrophic growth environment; Placed in heterotrophic and anaerobic environment,had the performance characteristics that could rapidly produce hydrogen.For such a special ecological system, Study its symbiotic mechanism and the connection between these populations of carbon and energy issues, will have a very important significance. We intended from the characteristics of the population, the secretion product of cell surface, free substance in the liquid medium like polysaccharide, protein and fatty acids carrying out research. Part I: The basic features of mixed autotrophic ammonia oxidizing populations . Use inorganic liquid medium, processed study for ammonia oxidation characteristics of the population; we used scanning electron microscopy to get micro-features of autotrophic ammonia oxidizing populations .The medium was carried out settlement and centrifugal then removed the microbial populations, after all of that we analysis the water phase for total organic carbon(TOC), carbohydrate and other substances; Solid ammonia oxidizing medium was adopted to separation and purification of population, DGGE means was for structure analysis of microbial population. The results showed that after the inoculum of bacteria (2 / 5000 (V / V)), ammonia in the culture medium (200 mg / L) was rapid degradation in 3-5 days; ammonia and nitrite have the negative correlation between changes in the trend, then only a small amount of nitrate content (<30mg / L). The biomass growth of ammoxidation population in line with the trend of ammonia oxidation, the initial volume of it was 7.75 mg / L (protein content), in 3-5 days upto 63.06 mg / L (protein content). Electron microscope image showed, the populations were wrapped in a layer of mucus, including the a large number ruptted micorbe , Centrifuge to remove bacteria, then detected the medium for total organic carbon and sugar content, result took on the same characteristics with biomass growth, that were from the initial 3.73、2.35 mg / L respectively, in 3-6 days achieved rapid increase in the maximum to 35.19、27.45 mg / L respectively. After initial separation、 purification ,then processed sequencing to strains purified and got the result that there were 10 heterotrophic microorganisms : Brucella Branch pale bacillus, Cellu lomonas, Bacillus species category, a Flavobacterium, colorless Bacteria, Aeromonas sheath fat, little support maltophilia Aeromonas, macrophages species hydrogen, sulphur-MI, Pseudomonas bacteria spores; DGGE display, there were 20 separation bands approximately. Part II: Mixed populations that autotrophic - heterotrophic bacteria symbiotic mechanism. On the basis of preliminary analysis of microbial population characteristics, aiming at extracellular carbohydrate components might be decomposition by microbial, we focused on microbial cell protein and carbohydrate analysis. Using ultrasound combined with RIPA lysis cracking the cells, SDS-PAGE electrophoresis analysis the total protein species of the population, and through the amino acid analyzer studied the compositions of amino acid and infrared spectroscopy analysis of a protein infrared characteristics. Using ultrasound combined with repeatedly freezing and thawing to treated the cell sample, then took the means that alcohol precipitation, deproteinization by Sevage, gel filtration aimed at desalination and grade separation to deal with the lysates . The extraction of sugar analysis included: UV scanning, IR, NMR, single-sugar composition analysis. SDS-PAGE analysis showed that: 42 kD protein expression was very high at different growth stages of mixed autotrophic ammonia oxidizing populations , on the fourth day, 42 kD protein expression had been very strong, 4-7d, it had continued this excessive expression, then started to weaken after 7 days. 42 kD protein that might be closely associated with ammonia oxidation. Infrared spectral analysis showed that: cell extracts with the characteristic that the peak distribution in 3427.42 cm-1、1718.18 cm-1 and 1681.72 cm-1、1160.07 cm-1 and 1086.74 cm-1 corresponding to OH、C = O、C-O-C Groups which had the typical characteristics of protein; and analysis showed that amino acids including Gly, Asp, Ala, Glu ,the content in the protein is relatively high. Exopolysaccharide in the extracts had the separation map that it was uneven, received a total of six collection peaks by the detection mode of phenol-sulphruic acid method ; ultraviolet scan in the 201-213 nm department had polysaccharide absorbing peak, the same ingredients that polysaccharide heterogeneity; infrared polysaccharide spectral characteristics of the main peak at 3400.49 cm-1, 2920.28 cm-1, 1154.54 and 1087.52 cm-1, corresponding OH,-CH2-or CH, C-O-H or C-O-C;and other characteristics of polysaccharide group; 1H NMR of polysaccharide extract appeared absorption peak between d4.3 ~5.9, which is the apparent evidence of polysaccharide, In 1H NMR, the hydrogen signal of one of O-acetyl was between 1.1 to 1.3. The determination of Sugar oxime whole benzoate derivatives by HPLC, there was a single-sugar peak, as a matter of time, yet more in-depth test. Summary: Mixed autotrophic ammonia oxidizing populations show us that it had the ability in ammonia oxidizing and it was great, organic matter and biomass increased significantly in the process of ammonia oxidation. Microbial populations was wrapped up slime layer, the phenomenon of cell breakdown obviously, and there were a lot of separation and purification of the heterotrophic bacteria; a lot of organic matter (including polysaccharides)remined in the medium that removal of cell indicated the inorganic system existed secondary carbon sources that could be used by the heterotrophic bacteria ; there were a large number proteins bands of cell extract, rich variety; cell extracts of polysaccharide had obvious characteristics of polysaccharide, and the existence evidence of single-sugar. Combined population of microscopic characteristics and free of organic matter in the test results, we believe that the health of inorganic system, population growth occurred in the course of the breakdown of the phenomenon is likely to lead to a lot of protein and polysaccharide released into the extracellular free, And other heterotrophic bacteria use them to the growth as carbon and nitrogen. This may be autotrophic system, the large number of heterotrophic bacteria symbiotic mechanism.

Heavy-ion conformal irradiation in the shallow-seated tumor therapy terminal at HIRFL

Basic research related to heavy-ion cancer therapy has been done at the Institute of Modern Physics (IMP), Chinese Academy of Sciences since 1995. Now a plan of clinical trial with heavy ions has been launched at IMP. First, superficially placed tumor treatment with heavy ions is expected in the therapy terminal at the Heavy Ion Research Facility in Lanzhou (HIRFL), where carbon ion beams with energy up to 100 MeV/u can be supplied. The shallow-seated tumor therapy terminal at HIRFL is equipped with a passive beam delivery system including two orthogonal dipole magnets, which continuously scan pencil beams laterally and generate a broad and uniform irradiation field, a motor-driven energy degrader and a multi-leaf collimator. Two different types of range modulator, ripple filter and ridge filter with which Guassian-shaped physical dose and uniform biological effective dose Bragg peaks can be shaped for therapeutic ion beams respectively, have been designed and manufactured. Therefore, two-dimensional and three-dimensional conformal irradiations to tumors can be performed with the passive beam delivery system at the earlier therapy terminal. Both the conformal irradiation methods have been verified experimentally and carbon-ion conformal irradiations to patients with superficially placed tumors have been carried out at HIRFL since November 2006.

Shallow gas in the muddy sediments of Eckernförde Bay, Germany

The seafloor of central Eckernförde Bay is characterised by soft muddy sediments that contain free methane gas. Bubbles of free gas cause acoustic turbidity which is observed with acoustic remote sensing systems. Repeated surveys with subbottom profiler and side scan sonar revealed an annual period both of depth of the acoustic turbidity and backscatter strength. The effects are delayed by 3–4 months relative to the atmospheric temperature cycle. In addition, prominent pockmarks, partly related to gas seepage, were detected with the acoustic systems. In a direct approach gas concentrations were measured from cores using the gas chromatography technique. From different tests it is concluded that subsampling of a core should start at its base and should be completed as soon as possible, at least within 35 min after core recovery. Comparison of methane concentrations of summer and winter cores revealed no significant seasonal variation. Thus, it is concluded that the temperature and pressure influences upon solubility control the depth variability of acoustic turbidity which is observed with acoustic remote sensing systems. The delay relative to the atmospheric temperature cycle is caused by slow heat transfer through the water column. The atmospheric temperature cycle as ‘exiting function’ for variable gas solubility offers an opportunity for modelling and predicting the depth of the acoustic turbidity. In practice, however, small-scale variations of, e.g., salinity, or gas concentration profile in the sediment impose limits to predictions. In addition, oceanographic influences as mixing in the water column, variable water inflow, etc. are further complications that reduce the reliability of predictions.