In-situ synthesis of AlN powders and composite AlN powders with yttrium addition

Using Al-Mg and Al-Mg-Y alloys as raw materials and nitrogen as gas reactants, AIN powders and composite AIN powders by in-situ synthesis method were prepared. AIN lumps prepared by the nitriding of Al-Mg and Al-Mg-Y alloys have porous microstructure, which is favorable for pulverization. They have high purity, containing 1.23 % (mass fraction) oxygen impurity, and consisted of AIN single phase . The average particle size of AIN powders is 6.78 mum. Composite AlN powders consist of AlN phases and rare, earth oxide Y2O3 phase. The distribution of particle size of AIN powders shows two peaks. In view, of packing factor, AIN powders with such size distribution can easily be sintered to high density.

Nanodiamond formation by hot-filament chemical vapor deposition on carbon ions bombarded Si

Nanocrystalline diamond films were grown by a two-step process on Si(1 0 0) substrate, which was first pretreated by pure carbon ions bombardment. The bombarded Si substrate was then transformed into a hot-filament chemical vapor deposition (HFCVD) system for further growth. Using the usual CH4/H-3 feed gas ratio for micro crystalline diamond growth, nanodiamond crystallites were obtained. The diamond nucleation density is comparable to that obtained by biasing the substrate. The uniformly distributed lattice damage is proposed to be responsible for the formation of the nanodiamond. (C) 2002 Elsevier Science B.V. All rights reserved.

Violet/blue emission from hydrogenated amorphous carbon films deposited from energetic CH3+ ions and ion bombardment

Considering the complexity of the general plasma techniques, pure single CH3+ ion beams were selected for the deposition of hydrogenated amorphous (a) carbon films with various ion energies and temperatures. Photoluminescence (PL) measurements have been performed on the films and violet/blue emission has been observed. The violet/blue emission is attributed to the small size distribution of sp(2) clusters and is related to the intrinsic properties of CH3 terminals, which lead to a very high barrier for the photoexcited electrons. Ion bombardment plays an important role in the PL behavior. This would provide further insight into the growth dynamics of a-C:H films. (C) 2002 American Institute of Physics.

Intense room temperature near infrared emission from Al (3+) and Yb3+ ions

Intense near infrared emission was observed from Al3+ and Yb3+ ions co-implanted SiO2 film on silicon. It was found that the addition of Al3+ ions could remarkably improve the photoluminescence efficiency of Yb3+-implanted SiO2 film. No excitation power saturation was observed and trivial temperature quenching factor of 2 was achieved.

Broad-spectrum and long-lifetime emissions of Nd3+ ions in lead fluorosilicate glass

A novel Nd3+-doped lead fluorosilicate glass (NPS glass) is prepared by a two-step melting process. Based on the absorption spectrum a Judd-Ofelt theory analysis is made. The emission line width of NPS glass is 44.2nm. The fluorescence decay lifetime of the 4F3/2 level is 586±20μsec, and the stimulated emission cross-section is 0.87×10-20cm2 at 1056nm. A laser oscillation is occurred at 1062nm when pumped by 808nm Diode Laser. The slope efficiency is 23.7% with a 415mJ threshold. It is supposed that NPS glass is a good candidate for using in ultra-short pulse generation and amplification by the broad emission bandwidth and long fluorescence lifetime.

富钇稀土-铝合金制取的研究Study on Preparation of Yttrium-Rich RE-Al Alloys

我国江西龙南稀土矿是目前世界上储量最大的富钇稀土矿、研制具有多种用途的钇（Y）-铝（Al）或富钇混合稀土（Ymm）-铝中间合金，对于开拓我国龙南稀土矿的应用领域扩大稀土合金出口具有重要意义。基于这一背景并针对目前氟化物体系制取Ymm-Al合金时存在着电解温度高，腐蚀现象严重，电效偏低等缺点，本文系统开展了在氯化物熔盐体系中电解制取Ymm-Al合金的研究工作。本工作由三部分组成：在第一部分工作中，开展了熔盐电解所需要基本原料-无水稀土氯化物制取的工艺研究。利用化学分析和结构分析手段，弄清了干法氯化过程中YmmCl_3水解的机理，提出了减弱水解的措施，即YmmCl_3先在850-900 ℃灼烧1.5 + 0.2hr，脱掉吸附水并将碱式碳酸盐转化为氧化物，增加稀土氧化物的比表面。通过条件试验得到最佳工艺条件为：采用NH_4 Cl:Ymm_2 O_3 = 14:1（摩尔比）的配料比，每次投入氯化装置的原料量为0.26 - 0.36 kg, 在400-450 ℃氯化反应激烈开始后迅速降温至400 ℃以下，待物料粘结现象消失后，再行升温氯化。出料及后期控制温在475 ± 25 ℃。经过3.8 ± 0.2hr氯化，可制得水不溶物小于1%并符合熔盐电解要求的YmmCl_3原料。此新工艺与原有干法工艺相比，流程短，装置简单，不需密闭抽真空，成本低，适于制取任何量的优质熔盐电解所需氯化稀土原料。在第二部分工作中，利用上述YmmCl_3原料，以液态铝为阴极，在氯化物体系中进行熔盐电解，通过试验得出在小型试验规模制取Ymm-Al合金的最隹工艺条件为：电解质组成（重量比）40%YmmCl_3-1%NaF-59%等摩尔的NaCl-KCl；电解温度为790 ± 5 ℃；阴极电流密为0.7 - 0.02A/cm~2；电解电量为333 ± 5库仑/克铝，制得钇铝合金中Ymm含量为10 ± 2%。添加1%的NaF可消除阴极表面生成枝状物，减少合金中夹渣和熔盐中沉渣。在电解工作中，将方差分析应用于试验数据处理，方差分析结果表明，各种试验因素对电效有明显影响，试验数据可靠，试验误差在允许范围以内。在第三部分工作中，利用线性扫描伏安法测定了在最隹电解工艺条件下Y~（3+）和Ymm在液态铝及钼电极上的析出电位。测定结果表明：Y~（3+）和Ymm~（3+）在液态铝阴极上的析出电位比在钼阴极上偏正0.2 ～ 0.8伏，氟离子的加入要比不加氟时析出电位不有同程度的负移，但考虑到氟离了具有消渣作用，加入少量氟比物添加剂对提高电效有利。