Genetic improvement on Chinese shrimp (Fenneropenaeus chinensis): growth and viability performance in F1 hybrids of different populations

Fenneropenaeus chinensis distributed in the Yellow Sea and Bohai Sea of China and the west coast of the Korean Peninsula. Different geographical populations represent potentially different genetic resources. To learn further the characteristics of different geographical population, crosses among two wild and three farmed populations were produced. The two wild populations were from the Yellow Sea and Bohai Sea (WYP), and the west coast of the Korean Peninsula and coast (WKN). The three farmed populations included the offspring of first generation of wild shrimp from coast in Korea (FKN), the Huang Hai (the Yellow Sea in Chinese) No.1 (HH1), and JK98. The phenotypes growth and survival rates of these populations were compared to confirm the feasibility for crossbreeding. The body length (BL), carapace length (CL), carapace width (CW), height of the second and third abdominal segment (HST), width of the second and third abdominal segment (WST), length of the first abdominal segment (LF), length of the last abdominal segment (LL), live body weight (BW), and survival rate were measured. Different combinations were statistically performed with ANOVA and Duncan's Multiple Range Test. The results show that the survival rate of JK98(a (TM) Euro)xWKN(a (TM),) was the highest, followed by WYP(a (TM) Euro)xWKN(a (TM),), FKN(a (TM) Euro)xWYP(a (TM),), FKN(a (TM) Euro)xHH1(a (TM),) and WYP(a (TM) Euro)xFKN(a (TM),); the body weight of FKN(a (TM) Euro)sxHH1(a (TM),) was the highest, followed by FKN(a (TM) Euro)xWYP(a (TM),), WYP(a (TM) Euro)xWKN(a (TM),), WYP(a (TM) Euro)xFKN(a (TM),) and JK98(a (TM) Euro)xWKN(a (TM),); the total length had the same ranking as the body weight. All growth traits in hybrids JK98(a (TM) Euro)xWKN(a (TM),) were the lowest among all combinations. F1 hybrids had significant difference (P < 0.05) in BL, CL, HST, LL, and BW; and insignificant difference (P > 0.05) in other growth traits and survival rate. The results of Duncan's Multiple Range Test are that BL and CL of JK98(a (TM) Euro)xWKN(a (TM),) were significantly different from the other combinations; HST different from the combination of FKN(a (TM) Euro)xWYP(a (TM),), FKN(a (TM) Euro)xHH1(a (TM),) and WYP(a (TM) Euro)xWKN(a (TM),); and BW different from FKN(a (TM) Euro)xWYP(a (TM),) and FKN(a (TM) Euro)xHH1(a (TM),). As a whole, the results indicate that the FKN(a (TM) Euro)xHH1(a (TM),) was the best combination in all growth traits. Therefore, hybridization can introduce the variation to base populations. The systematic selection program based on additive genetic performance may be more effective than crossbreeding.

Millstone Hill电离层F层等效风场的气候学研究

Neutral winds and electric fields in the ionospheric F layer play important roles in the variations of the ionosphere, and also affect the thermospheric circulation via the close coupling between the ionosphere and the thermosphere. By now, the neutral winds and electric drifts are generally observed with ground-based Fabry-Perot interferometers (FPI) and incoherent scatter radars (ISR), rockets, and satellite-borne instrument. Based on the servo theory, the ionospheric equivalent winds, which include the information of both the neutral winds and electric fields, can be derived from these characteristic parameters observed by ionosondes. This indirect derivation has potential values in climatological researches and space weather forecast. With the data set of the incoherent scatter radar observations at Millstone Hill, USA, from 1976 to 2006, we statistically analyzed the climatological variations of the vertical component of the equivalent winds (VEWs) over Millstone Hill, which are derived from the ionospheric key parameters (the peak electron number density and peak height of the F2 layer, NmF2 and hmF2) on the basis of the servo theory, Liu's method, and measurements from the ion line-of-sight velocity as well. The main results of this analysis are summarized as follows: (1) The values of VEWs over Millstone Hill during nighttime are stronger than in the daytime, and the upward drift dominates most of the day. In 1993, Hagan found that the component of the neutral winds in the magnetic meridion in daytime is weaker than during nighttime under both solar maximum and minimum conditions; he also found that the equatorward winds dominate most of the day. Both results suggest that the thermosphere in Millstone Hill is modulated by the aurorally driven high-latitude circulation cell; that is, during geomagnetic quiet periods, the average auroral activity is strong enough to drive thermospheric circulation equatorward for most of the day at Millstone Hill. Moreover, since ion drag is the strongest during daytime when F region densities are enhanced by photoionization, the wind speeds are smaller during the daytime than in the nighttime. (2) There is equinoctial symmetry in VEWs at Millstone Hill. The amplitudes and phases of VEWs in spring are quite similar to those in autumn. In contrast, the nighttime upward drift in winter is weaker than in summer and the difference becomes more significant with increasing solar activity. This solstice asymmetry indicates that, the aurorally driven circulation in the northern hemisphere at Millstone Hill latitude is weaker in winter due to arctic darkness, because the subsolar point is in the southern hemisphere. (3) The comparison of the VEWs derived from three methods, i.e., the servo theory, Liu's method, and the ISR ion line-of-sight velocity measurements, indicates that the amplitudes and main phase tendencies of these VEWs accord well with each other during nighttime hours. However, the case in the daytime is relatively worse. This daytime discrepancy can be explained in terms of the effects of photochemical processes and the choices of the servo constants. A larger servo constant gives a stronger plasma drift in daytime. Therefore, this study tells how important to choose a suitable constant for deriving VEWs at Millstone Hill.

Thermoplastic shear localisation in titanium alloys during dynamic deformation

Cylindrical specimens (4 mm diameter and 4 mm height) of titanium alloy bar were given various heat treatments to provide a wide range of microstructures and mechanical parameters. These specimens were then subjected to high plastic strain at a large strain rate (103 s-1 ) during dynamic compression by a split Hopkinson bar at ambient temperature. The microstructures of the localised shear bands were examined by optical and transmission electron microscopy. The results show that there are two types of localised shear bands: deformed and white shear bands. A detailed observation reveals that there is no difference in the nature of the deformed and white shear bands, but they occur at different stages of localised deformation. It is found that there is a burst of strain, corresponding to a critical strain rate at which the white shear band occurs and no phase transformation occurs in the shear bands.

Experimental Study the Flow Pattern in Thermal Capillary Convection

In the present research work, the thermal capillary convection has been investigated and measured by particle image velocimetry (PIV) technique. There is one liquid layer in a rectangular cavity with different temperature’s sidewalls. The cavity is 52mm,42mm,20mm, 4mm in height of the silicon oil liquid layer. A sidewall of the cavity is heated by electro-thermal film, another sidewall is cooled by the semiconductor cooling sheet. The velocity field and the stream lines in cross section in liquid layer have been obtained at different temperature difference. The present experiment demonstrates that the pattern of the convection mainly relates with temperature difference.

Boiling heat transfer enhancement by using micro-pin-finned surface for electronics cooling

For efficiently cooling electronic components with high heat flux, experiments were conducted to study the flow boiling heat transfer performance of FC-72 over square silicon chips with the dimensions of 10 × 10 × 0.5 mm3. Four kinds of micro-pin-fins with the dimensions of 30 × 60, 30 × 120, 50 × 60, 50 × 120 μm2 (thickness, t × height, h) were fabricated on the chip surfaces by the dry etching technique for enhancing boiling heat transfer. A smooth surface was also tested for comparison. The experiments were made at three different fluid velocities (0.5, 1 and 2 m/s) and three different liquid subcoolings (15, 25 and 35 K). The results were compared with the previous published data of pool boiling. All micro-pin-fined surfaces show a considerable heat transfer enhancement compared with a smooth surface. Flow boiling can remarkably decrease wall superheat compared with pool boiling. At the velocities lower than 1 m/s, the micro-pin-finned surfaces show a sharp increase in heat flux with increasing wall superheat. For all surfaces, the maximum allowable heat flux, qmax, for the normal operation of LSI chips increases with fluid velocity and subcooling. For all micro-pin-finned surfaces, the wall temperature at the critical heat flux (CHF) is less than the upper limit for the reliable operation of LSI chips, 85◦C. The largest value of qmax can reach nearly 148 W/cm2 for micro-pin-finned chips with the fin height of 120 μm at the fluid velocity of 2 m/s and the liquid subcooling of 35 K. The perspectives for the boiling heat transfer experiment of the prospective micro-pin-finned sur- faces, which has been planned to be made in the Drop Tower Beijing/NMLC in the future, are also presented.

飞秒激光辐射下微突起结构形成的超快热弹性模拟

本文结合有限元方法和超快热弹性模型对飞秒激光辐射下形成的微突起结构进行了数值模拟研究。模拟结果表明微突起结构的形成与入射飞秒激光的参数以及材料的热弹性质有关。在圆锥状微突起结构的形状和高度方面，实验结果与模拟结果呈现良好的一致性，这也从实验上表明了超快热弹性模型的有效性。本文的研究将有助于利用超快激光对薄膜材料进行纳米构造。

静动结合的化学腐蚀法制备近场光学探针的理论分析

理论上分析了静动结合的化学腐蚀法制备探针的具体机理及过程。在静态腐蚀的过程中, 利用流体力学Young-Laplace方程的一级近似解获得了光纤插入到HF酸中形成的新月形高度。在动态腐蚀过程中, 详细分析了当静态腐蚀时间和动态腐蚀时间分别取不同值时, 光纤移动速度对光纤探针结构的影响。利用此法可制备出尖端锐利、大锥角或多锥体等各种结构的光纤探针。这为实验上制备出性能优良的探针, 为拓宽扫描近场光学显微镜的应用范围奠定基础。将上述理论分析的结果与本文实验中所得初步结果进行了比较, 所得结果一致。

机载激光测深系统中海面波浪影响的改正

针对研制的新型机载激光测深系统的海上飞行试验数据,进行预处理、信息提取、数据同步和坐标转换后,开展波浪改正研究.对海底高程的GPS高程信息无波浪改正、GPS高程信息改正飞机航高变化计算波浪和加速度信息改正飞机航高变化计算波浪三种技术进行了分析.数据处理结果表明,采用加速度信息改正飞机航高变化计算得到的波浪信息的方法,结果较好,可满足研制的机载激光测深系统的要求.

不同类型蒸发源对平面夹具薄膜均匀性的影响

分析了几种可能的实际蒸发源与薄膜均匀性的关系，其中包括扩展的平面蒸发源和曲面蒸发源。通过实验论证了薄膜均匀性对蒸发源尺寸和蒸发特性的依赖关系。得到的分析结果表明：当蒸发源半径和夹具高度的比值小于1／17时，蒸发源可以被视为一个点面源；大于1／10时，应当把蒸发源视为面面源进行考虑。当挖坑深度和蒸发源半径的比值介于0和0．5之间时，挖坑对薄膜均匀性造成的影响基本可以忽略；大于0．6时，挖坑效应明显影响薄膜的均匀性。

Size self-scaling effect in stacked InAs/InAlAs nanowire multilayers

Size self-scaling effect in stacked InAs/In0.52Al0.48As nanowires on InP substrates is revealed, i.e., the base width and height of the InAs nanowires have clear proportional dependence on thickness of the InAlAs spacer layer used in different samples. The photoluminescence wavelength from different samples, which varies between 1.3 and 1.9 mum, is also found closely correlated to the size self-scaling effect. This phenomenon can be well explained in the context of formation mechanism and growth features of the InAs/InAlAs nanowire arrays. The finding illustrates a degree of freedom to control the structural and optical properties of strained self-organized nanostructures. (C) 2004 American Institute of Physics.

Self-organized InAs quantum wires on GaAs (331)A substrates

Self-organized InAs quantum wires (QWRs) were fabricated on the step edges of the GaAs (331)A surface by molecular beam epitaxy. The lateral size of InAs QWRs was saturated by the terrace width (i.e., 90 nm) while the size along the step lines increased with the increasing thicknesses of the InAs layers, up to 1100 nm. The height of InAs QWRs varied from 7.9 nm to 13 nm. The evolution of the morphology of InAs QWRs was attributed to the diffusion anisotropy of In adatoms.

Single-negative negative index metamaterials with broad bandwidth - art. no. 683109

The theoretical method to design negative refractive index metamaterials by single negative permittivity metamaterials is presented. By designing the electric and magnetic response metamaterials separately, the complexity of the design work can be simplified a lot. For the magnetic response metamaterials, the metallic post structure is adopted. Varying the height of the post, the response wavelength can be adjusted linearly. For electric metamaterials, wire-mesh structure is adopted. The effective material parameters, including refractive index, impedance, permittivity and permeability are given. Such a structure has negative refractive index during a broad frequency band and easy to design.

Optimized design on high-power GaN-based Micro-LEDs - art. no. 684108

The structure of micro-LEDs was optimized designed. Optical, electrical and thermal characteristics of micro-LEDs were improved. The optimized design make micro-LEDs suitable for high-power device. The light extraction efficiency of micro-LEDs was analyzed by the means of ray tracing. The results shows that increasing the inclination angle of sidewall and height of mesa, and reducing the absorption of p and n electrode can enhance the light extraction efficiency of micro-LEDs. Furthermore, the total light output power can be boosted by increasing the density of micro-structures on the device. The high-power flip-chip micro-LEDs were fabricated, which has higher quantum efficiency than conventional BALED's. When the number of microstructure in micro-LEDs was increased by 57%, the light output power was enhanced 24%. Light output power is 82.88mW at the current of 350mA and saturation current is up to 800mA, all of these are better than BALED which was fabricated in the same epitaxial wafer. The IN characteristics of micro-LEDs are almost identical to BALED.

Hydrogen sensors based on Pt-AlGN/AIN/GaN Schottky diode - art. no. 68291R

Pt/AlGaN/AlN/GaN Schottky diodes have been fabricated and characterized for H-2 sensing. Platinum (Pt) with a thickness of 20nm was evaporated on the sample to form the Schottky contact. The ohmic contact, formed by evaporated Ti/Al/Ni/Au metals, was subsequently annealed by a rapid thermal treatment at 860 degrees C for 30 s in N-2 ambience. Both the forward and reverse current of the device increased greatly when exposed to H-2 gas. The sensor's responses under different hydrogen concentrations from 500ppm to 10% H-2 in N-2 at 300K were investigated. A shift of 0.45V at 297K is obtained at a fixed forward current for switching from N-2 to 10% H-2 in N-2. Time response of the sensor at a fixed bias of 0.5 V was also measured. The turn-on response of the device was rapid, while the recovery of the sensor at N-2 atmosphere was rather slow. But it recovered quickly when the device was exposed to the air. The decrease in the barrier height of the diode was calculated to be about 160meV upon introduction of 10% H-2 into the ambient. The sensitivity of the sensor is also calculated. Some thermodynamics analyses have been done according to the Langmuir isotherm equation.

Resonance-enhanced group delay times in an asymmetric single quantum barrier

It is shown that transmission and reflection group delay times in an asymmetric single quantum barrier are greatly enhanced by the transmission resonance when the energy of incident particles is larger than the height of the barrier. The resonant transmission group delay is of the order of the quasibound state lifetime in the barrier region. The reflection group delay can be either positive or negative, depending on the relative height of the potential energies on the two sides of the barrier. Its magnitude is much larger than the quasibound state lifetime. These predictions have been observed in microwave experiments. (c) 2005 Elsevier B.V. All rights reserved.