Effects of sapphire substrate annealing on ZnO epitaxial films grown by MOCVD

The annealing effects of sapphire substrate on the quality of epitaxial ZnO films grown by metalorganic chemical vapor deposition (MOCVD) were studied. The atomic steps formed on (0 0 0 1) sapphire (alpha-Al2O3) substrate surface by annealing at high temperature was analyzed by atomic force microscopy (AFM). The annealing effects of sapphire substrate on the ZnO films were examined by X-ray diffraction (XRD), AFM and photoluminescence (PL) measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface., The optimum annealing temperature of sapphire substrates is given. (c) 2006 Elsevier B.V. All rights reserved.

Growth and properties of ZnO thin film on beta-Ga2O3(100) substrate by pulsed laser deposition

Zinc oxide (ZnO) thin films were grown on the beta-Ga2O3 (100) substrate by pulsed laser deposition (PLD). X-ray diffraction (XRD) indicated that the ZnO films are c-axis oriented. The optical and electrical properties of the films were investigated. The room temperature Photoluminescence (PL) spectrum showed a near band emission at 3.28 eV with two deep level emissions. Optical absorption indicated a visible exciton absorption at room temperature. The as-grown films had good electrical properties with the resistivities as low as 0.02 Omega cm at room temperature. Thus, beta-Ga2O3 (100) substrate is shown to be a suitable substrate for fabricating ZnO film. (c) 2006 Elsevier B.V. All rights reserved.

Optical properties of ZnO thin film on gamma-LiAlO2 substrate grown by pulsed laser deposition

Optical properties were investigated of ZnO thin films grown oil (100) gamma-LiAlO2 (LAO) substrates by pulsed laser deposition method. C-axis oriented ZnO film was grown oil (100) LAO substrate at the substrate temperature of 550 degrees C. The transmittances of the films were over 85%. Peaks attributed to excitons were seen in the absorption spectra, indicating that the thin films have high crystallinity. Photoluminescence spectra were observed at room temperature; the peak at 550 urn is ascribed to oxygen vacancies in the ZnO films caused by the diffusion of Li from the substrate into the film during deposition. (c) 2005 Elsevier B.V. All rights reserved.

Study on the hydrolytic property and thermal stability of LiAlO2 substrate

The hydrolytic property and thermal stability of LiAlO2 (LAO), important factors for its application, were examined by AFM and X-ray rocking curve. We found that H2O may be deleterious for LAO surface polishing when the root mean square (RMS) value is less than 1 nm. However, when the RMS value is more than 1 nm it may be useful for LAO polishing. (100)-plane LAO substrates are annealed in the range of 850-900 degrees C in flux N-2, Slick AlN layer probably is produced on the substrate surface. M-plane GaN layer has grown on the substrate by metal-organic chemical vapor deposition (MOCVD) method. Theses results show that LiAlO2 crystal is a promising substrate of fabricating high-efficiency LEDs by MOCVD. (c) 2006 Elsevier B.V. All rights reserved.

Composite substrate LiGaO2(001)/beta-Ga2O3(100) fabricated by vapor transport equilibration

Highly (001) orientation LiGaO2 layers have been successfully fabricated on (100) beta-Ga2O3 surface by vapor transport equilibration (VTE) technique. The temperature is very important for the WE treatment. At low temperature (800 degrees C), LiGaO(2)layers are textured. As the temperature was raised to 1100 C the layer becomes highly oriented in the [100] direction. It shows that the best temperature for WE treatment is 1100 degrees C. This technique is promising to fabricate small lattice mismatch composite substrate of LiGaO2 (001)//beta-Ga2O3 (100) for GaN films. (c) 2006 Elsevier B.V. All rights reserved.

Study on growth and properties of novel gamma-LiAlO2 substrate

Transparent gamma-LiAlO2 single crystal has been grown by Temperature Gradient technique. The surface of the wafer annealed in O-2-atmosphere at 1100 degrees C for 70 h became opaque and Li-poor phase (LiAl5O8); while, that annealed in Li-rich atmosphere kept transparent and smooth. The full-width at half maximum value dropped to 30 arcsecs when the wafer was annealed in Li-rich atmosphere. That annealed in O-2-atmosphere increased to 78 arcsec. Compared with absorption spectra, we can conclude that the 196 nm absorption peak was caused by Li vacancies and the 736 nm peak was caused by O vacancies.

Formation of arrayed holes on metal foil and metal film by multibeam interfering femtosecond laser beams

We report on an optical interference method to fabricate arrayed holes on metal nickel foil and aluminum film deposited on glass substrate by means of five-beam interference of femtosecond laser pulses. Optical microscope and scanning electron microscope observations revealed that arrayed holes of micrometre-order were fabricated on both metal foil and metal film. The present technique allows one-step, large-area, micrometric processing of metal materials for potential industrial applications.

Structural, morphological and optical properties of ZnO thin films grown on gamma-LiAlO2 substrate by pulsed laser deposition

ZnO thin films were deposited on the substrates of (100) gamma-LiAlO2 at 400, 550 and 700 degrees C using pulsed laser deposition (PLD) with the fixed oxygen pressure of 20 Pa, respectively. When the substrate temperature is 400 degrees C, the grain size of the film is less than 1 mu m observed by Leitz microscope and measured by X-ray diffraction (XRD). As the substrate temperature increases to 550 degrees C, highly-preferred c-orientation and high-quality ZnO film can be attained. While the substrate temperature rises to 700 degrees C, more defects appears on the surface of film and the ZnO films become polycrystalline again possibly because more Li of the substrate diffused into the ZnO film at high substrate temperature. The photoluminescence (PL) spectra of ZnO films at room temperature show the blue emission peaks centered at 430 nm. We suggest that the blue emission corresponds to the electron transition from the level of interstitial Zn to the valence band. Meanwhile, the films grown on gamma-LiAlO2 (LAO) exhibit green emission centered at 540 nm, which seemed to be ascribed to excess zinc and/or oxygen vacancy in the ZnO films caused by diffusion of Li. from the substrates into the films during the deposition.

Deposition of ZnO thin films on (100) γ-LiAlO2 substrate

Optical properties for ZnO thin films grown on (100) γ-LiAlO2 (LAO) substrate by pulsed laser deposition method were investigated. The c-axis oriented ZnO films were grown on (100) γ-LiAlO2 substrates at the substrate temperature of 550 Celsius degrees. The transmittance of the films was over 85%. Peaks attributed to excitons were shown in absorption spectra, which indicated that thin films had high crystallinity. Photoluminescence spectra with the maximum peak at 540 nm were observed at room temperature, which seemed to be ascribed to oxygen vacancy in the ZnO films caused by diffusion of Li from the substrates into the films during the deposition.

Annealing effects of sapphire substrate on properties of ZnO films grown by magnetron sputtering

The annealing effects of sapphire substrates on the quality of epitaxial ZnO films grown by dc reactive magnetron sputtering were studied. The atomic steps formed on (0001) sapphire (alpha-Al2O3) substrates surface by annealing at high temperature were analyzed by atomic force microscopy. Their influence on the growth of ZnO films was examined by X-ray diffraction and photoluminescence measurements. Experimental results indicate that the film quality is strongly affected by annealing treatment of the sapphire substrate surface. The optimum annealing temperature of sapphire substrates for ZnO grown by magnetron sputtering is 1400 degrees C for 1 h in air.

Characterization of m-plane ZnO thin film on gamma-LiAlO2 (100) substrate by metal-organic chemical vapor deposition

Non-polar (1 (1) over bar 00)m-plane ZnO thin film has been prepared on gamma-LiAlO2 (100)substrate via the low pressure metal organic chemical vapor deposition. Obvious intensity variation of the E-2 mode in the polarized Raman spectra and the absorption edge shift in the polarized optical transmission spectra indicate that the m-plane film exhibits optical anisotropy, which have applications in certain optical devices, such as the UV modulator and polarization-dependent beam switch. From the atomic force microscopy images, highly-oriented uniform-sized grains of rectangular shape were observed. (c) 2008 Elsevier B.V. All rights reserved.

Simulation of growth process of thin film on non-planar substrate

In (2 + 1) dimension, growth process of thin film on non-planar substrate in Kuramoto-Sivashinsky model is studied with numerical simulation approach. 15 x 15 semi-ellipsoids arranged orderly on the surface of substrate are used to represent initial rough surface. The results show that at the initial stage of growth process, the surface morphology of thin film appears to be grid-structure, and the interface width constantly decreases with the growth time, then reaches minimum. However, the grid-structure becomes ambiguous, and granules of different sizes distribute evenly on the surface of thin film with the increase of growth time. Thereafter, the average size of granules and the interface width gradually increase, and the surface morphology of thin film presents fractal properties. The numerical results of height-height correlation functions of thin film verify the surface morphology of thin film to be fractal for a longer growth time. By fitting of the height-height correlation functions of thin film with different growth times, the growth process is described quantitatively. (c) 2004 Elsevier B.V. All rights reserved.

Modelling analysis of influence of substrate surface defect on optical characteristics of single-layer coating

A simple and practical model is used to analyse the influence of substrate surface defect on the optical characteristics of a single-layer coating. A single-layer coating is prepared and its optical properties are fitted. Some explanations for the origin of the transition layer are presented. It is concluded that there is a transition layer forming between the substrate and coating, which is attributed to substrate surface defects, and its refractive index change is nearly of linearity.