An Experimental Study on Flame Propagation in Cornstarch Dust Clouds

Following the quantitative determination of dust cloud parameters, this study investigates the flame propagation through cornstarch dust clouds in a vertical duct of 780 mm height and 160 x 160 mm square cross section, and gives particular attention to the effect of small scale turbulence and small turbulence intensity on flame characteristics. Dust suspensions in air were produced using an improved apparatus ensuring more uniform distribution and repeatable dust concentrations in the testing duct. The dispersion-induced turbulence was measured by means of a particle image velocimetry (PIV) system, and dust concentrations were estimated by direct weighing method. This quantitative assessment made it possible to correlate observed flame behaviors with the parameters of the dust cloud. Upward propagating dust flames, from both closed/open bottom end to open/closed top end of the duct, were visualized by direct light and shadow photography. From the observation of propagation regimes and the measurements of flame velocity, a critical value of the turbulence intensity can be specified below which laminar flame propagation would be established. This transition condition was determined to be 10 cm/s. Laminar flames propagated with oscillations from the closed bottom end to the open top end of the testing duct, while the turbulent flames accelerated continuously. Both laminar and turbulent flames propagated with steady velocity from the open bottom end to the closed top end of the duct. The measured propagation velocity of laminar flames appeared to be in the range of 0.45-0.56 m/s, and it was consistent with the measurements reported in the literature. In the present experimental study, the influence of dust concentration on flame propagation was also examined, and the flame propagation velocity was found weakly sensitive to the variations in dust concentration. Some information on the flame structure was revealed from the shadow records, showing the typical heterogeneous feature of the dust combustion process.

沿平板可压缩湍流边界层的直接数值模拟

湍流广泛存在于自然界和工程应用中。可压平板湍流是一种典型的壁湍流，对其进行直接数值模拟研究是壁湍流机理研究的基础。本文采用高精度紧致型差分格式求解三维可压N-S方程，利用MPI并行程序，直接数值模拟了来流马赫数为M的＝2．25，雷诺数为Re＝635O00／in．的空间发展的可压缩平板湍流边界层。本文主要研究了如下一些问题。方法研究方面：●针对壁湍流流动的特点，文中提出了与基于非等距网格高精度紧致型差分格式相结合的简化的迭代一隐式时间推进法，建立了可压缩平板湍流边界层直接数值模拟方法。提高了计算效率，并给出了迭代收敛的条件。●研究了不同网格加密方法对数值解分辨率的影响，指出在保证近物面附近物理平面内网格是均匀的条件下，采用坐标变换的方法也可得到近物面高分辨率的数值解，纠正了人们认为只有在基于非等距网格上才能得到高分辨率解的观点。●采用包括前缘在内的二维可压平板层流边界层直接数值模拟结果为三维可压平板湍流边界层计算提供上游边界条件，解决了国外采用的局限性很大的经验公式带来的不相容问题。物理问题的模拟研究：●在国内首次给出了超声速平板边界层从层流经bypass转披直到充分发展湍流的整个过程。所得流场统计特征（如平均速度分布，物面摩阻系数，脉动速度的均方根等）与相关理论和实验符合甚好。这些结果充分证实了本文所建立的数值方法的有效性和所得结果的可靠性。●在此基础上，文中分析了可压平板湍流边界层内的拟序结构的形成过程。研究了初始扰动对平板边界层流动转挨特征的影响，指出上游初始扰动中展向的非对称性是形成bypass转挨的关键因素，且较大的时间扰动频率使得边界层转披位置后移。这些结果为壁湍流控制提供一定依据。●在此基础上研究了可压缩效应对平均流动特征以及湍能的生成和耗散特征的影响，指出在Mc∞=2.25的情况下，Morkovin假设基本成立。但可压缩效应使得边界层内层中过渡层加宽；拟序结构有明显差别。与不可压相比上抛、下扫对不同区域的作用有所不同。在近壁区，湍动能方程中的压力-膨胀项和压力-速度相关项仍是不可忽略的量，这导致声的产生和可压缩效应对湍流的发展所产生的抑制作用。

肝脏中生物流体流动的多重介质渗流模型和数值模拟

本文采用生物渗流理论，建立了肝脏内不同生物流体流动的多重介质渗流模型，采用有限元法求解这种特殊的渗流问题，根据数值计算结果揭示了肝内血液、组织液以及胆汁等的流动规律，并探讨了肝脏血流动力学的一些问题。论文将肝脏内部与生物代谢功能有关的肝血窦和窦周间隙当作两重并存的多孔介质，血液在肝血窦中，以及组织液在窦周间隙中的流动均当作渗流处理，通过Starling公式考虑了两重介质之间的流量交换，从而建立了肝血窦-窦周间隙的双重介质模型。针对肝脏胆汁分泌功能，将肝脏内密布的毛血肝管网当作多孔介质，以受静压及渗透压驱动的流体跨壁流动表示肝汁从肝细胞向毛细肝管的分泌，肝汁在毛细胆管网中的流动作为渗流处理，从而建立了肝汁分泌与输运的双重介质模型。采用有限元法求解了生物流体的双重介质渗流问题，针对非牛顿渗流和两重介质的相互作用，本文发展了一种嵌套迭代方法，即采用直接迭代求解血液在肝血窦中的非线性渗流，采用交替迭代解决双重介质渗流中由跨壁流支引起的相互流体交换，直接迭代嵌套于交替迭代中。这种算法比较有效的解决了包含非牛顿渗流的双重介质渗流问题。根据生物多孔介质中微细管系统的构筑方式以及不同微细管系统之间的联系方式，论文提出将生物多孔介质划分为分级多孔介质和多重多孔介质两种主要类型。基于多相混合物的平均化的理论，论文推导了双重多孔介质中的动量守恒方程、质量守恒方程以及相应的渗流方程，建立了双重多孔介质渗流的平均化模型。基于分级多孔介质渗流的理论，论文将脏器中的血管树按管径分为不同级别的多孔介质，各级血管中和血液流动均作为渗流处理，从而提出了计算脏器整体血流的一种渗流方法。采用这种方法，在论文提出的肝血窦 - 窦周间隙双重介质渗流流模型的基础之上，初步研究了肝脏门静脉系统的血液动力学规律。采用本文提出的肝血窦 - 窦周间隙双重介质模型和胆汁分泌 - 流动的双重介质模型，得到了血液、组织液和胆汁在肝小叶中的压力分布和速度分布，并分析了肝血窦壁的跨壁流动模式，胆汁流量的影响因素，以及窦周间隙中组织液流量与肝血窦中血液流动及肝血窦壁渗透系数等因素的关系，揭示了肝脏内血液、组织液及胆汁等生物流体流动的一般规律。

Detour behavior changes associated with prenatal morphine exposure in 11-day-old chicks

The central nervous system exhibits remarkable plasticity in early life. Prenatal morphine exposure may induce adverse behavioral effects on the neonate and the developing offspring. In the present study, we investigated the effect of prenatal morphine exposure (daily from embryonic days 12-16, 20 mg/kg) on 11-day-old chicks using two forms of spatial paradigms: one trial detour behavior task in which animals must bypass an obstacle to reach the desired goal without any training and detour learning task which required several trials of training to reach the detour criterion. The results showed that, on the condition that chicks could successfully detour in the first trial, morphine exposed chicks exhibited longer detour latency to finish the task, coupled by a preference for turning right versus turning left. In contrast, no significant difference in learning and memory was found in detour learning task between morphine exposed chicks and saline chicks. These findings suggest specific behavioral changes associated with prenatal exposure to opioids during mid to late gestation, also raise attention to the possible health hazard from pregnancy drug use in everyday life. (C) 2010 ISDN. Published by Elsevier Ltd. All rights reserved.

Predominant expression and cellular distribution of fish Agr2 in renal collecting system

Anterior gradient 2 (Agr2) genes encode secretory proteins, and play significant roles in anterior-posterior patterning and tumor metastasis. Agr2 transcripts were shown to display quite diverse tissue distribution in different species, and little was known about the cellular localization of Agr2 proteins. In this study, we identified an Agr2 homologue from gibe[ carp (Carassius auratus gibelio), and revealed the expression patterns and cellular localization during embryogenesis and in adult tissues. The full-length cDNA of CagAgr2 is 803 nucleotides (nt) with an open reading frame of 510 nt encoding 169 amino acids. The Agr2 C-terminus matches to the class I PDZ-interacting motif, suggesting that it might be a PDZ-binding protein. During embryogenesis, CagAgr2 was found to be transcribed in the mucus-secreting hatching gland from tailbud stage and later in the pharynx region, swim bladder and pronephric duct as revealed by RT-PCR and whole mount in situ hybridization. In the adult fish, its transcription was predominantly confined to the kidney, and lower transcription levels were also found in the intestine, ovary and gills. To further localize the Agr2 protein, the anti-CagAgr2 polyclonal antibody was produced and used for immunofluorescence observation. In agreement with mRNA expression data, the Agr2 protein was localized in the pronephric duct of 3dph larvae. In adult fish, Agr2 protein expression is confined to the renal collecting system with asymmetric distribution along the apical-basolateral axis. The data provided suggestive evidence that fish Agr2 might be involved in differentiation and secretory functions of kidney epithelium. (C) 2009 Elsevier Inc. All rights reserved.

Fridericia dianchiensis sp nov (Enchytraeidae, oligochaeta) from Yunnan Province, China

Fridericia dianchiensis, a new enchytraeid species collected from Yunnan Province, is described here. It is characterized by a combination of the following characters: 1) lateral bundles containing maximum 3 chaetae; 2) esophageal appendages with 3-4 simple, terminal branches; 3) dorsal vessel originating in XX-XXIII; 4) sub-neural glands absent; 5) seminal vesicle large, occupying two segments; 6)clitellum girdle-shaped or gland cells absent between bursal slits and pre-middle ventrally; 7) coelomocytes without refractile vesicles, 8) spermatheca without diverticula and both ampullae broadly united; and 9) long spermathecal ectal duct without gland at the orifice.

A taxonomic study of Oconnorella (Enchytraeidae, Oligochaeta) from Changbaishan Mountain, China

We describe three enchytraeid species, including two new species, from Mt. Changbaishan, Jilin Province, northeastern China. Oconnorella cheni sp. nov. is characterized by a simple spermatheca; absence of the oesophageal appendages and seminal vesicle; and nephridia from 6/7, with a distinct funnel and the efferent duct arising from the anterior part of the postseptale. Oconnorella globula sp. nov. is distinguished by a spermatheca with two diverticula; lack of oesophageal appendages and seminal vesicle; and nephridia from 6/7, with distinct funnel and the efferent duct arising from the mid-ventral or posteroventral part of the postseptale. We redescribe Oconnorella changbaishanensis (Xie et al., 2000) from type and live specimens, and amend some characters that cannot be investigated clearly from mounted specimens. We revise the generic diagnosis of Oconnorella.

Fridericia nanningensis, a new terrestrial enchytraeid species (Oligochaeta) from southwestern China

Fridericia nanningensis, a new species from wetland soil of Nanhu Park, Nanning city, the capital of Guangxi Zhuang Autonomous Region in southwest China, is described. It is characterized by 2-4 chaetae per bundle, poorly-developed clitellar glands, slender, unbranched peptonephridia, and spermathecae with 2 ampullar diverticula, a deep constriction in the middle of the ampulla and one large ectal gland. It is closely related to the European species, F. alata Nielsen & Christensen, 1959 and the East European species, F. tubulosa Dozsa-Farkas, 1972 by the shape of peptonephridia and the undeveloped clitellar glands. It differs from F. alata by its shorter body length and fewer chaetae per bundle, its type of coelomocytes (type "c"), its deep constriction in the middle of the spermathecae ampulla and a larger ectal gland, and it differs from F. tubulosa by its pale epidermal glands, its more anterior origin of the dorsal vessel, a deep constriction in the middle of the spermathecae ampulla, shorter ectal duct, and only one ectal gland at the spermathecal orifice.

Monolithic optical gates based on integration of evanescently-coupled uni-traveling-carrier photodiodes and electroabsorption modulators

We report on chip-scale optical gates based on the integration of evanescent waveguide unitraveling-carrier photodiodes (EC-UTC-PDs) and intra-step quantum well electroabsorption modulators (IQW-EAMs) on n-InP substrates. These devices exhibit simultaneously 2.1 GHz and -16.2 dB RF-gain at 21 GHz with a 450 Omega thin-film resistor and a bypass capacitor integrated on a chip.

Density Gradient Ultracentrifugation of Nanotubes: Interplay of Bundling and Surfactants Encapsulation

Density gradient ultracentrifugation (DGU) has emerged as a promising tool to prepare chirality enriched nanotube samples. Here, we assess the performance of different surfactants for DGU. Bile salts (e.g., sodium cholate (SC), sodium deoxycholate (SDC), and sodium taurodeoxycholate (TDC)) are more effective in individualizing Single Wall Carbon Nanotubes (SWNTs) compared to linear chain surfactants (e.g., sodium dodecylbenzene sulfonate (SDBS) and sodium dodecylsulfate (SDS)) and better suited for DGU. Using SC, a narrower diameter distribution (0.69-0.81 nm) is achieved through a single DGU step on CoMoCAT tubes, when compared to SDC and TDC (0.69-0.89 nm). No selectivity is obtained using SDBS. due to its ineffectiveness in debundling. We assign the reduce selectivity of dihydroxy bile salts (S DC and TDC) in comparison with trihydroxy SC to the formation of secondary micelles. This is determined by the number and position of hydroxyl ( OH) groups on the a-side of the steroid backbone. We also enrich CoMoCAT SWNT in the 0.84-0.92 nm range using the Pluronic F98 triblock copolymer. Mixtures of bile salts (SC) and linear chain surfactants (SOS) are used to enrich metallic and semiconducting laser-ablation grown SWNTs. We demonstrate enrichment of a single chirality, (6,5), combining diameter and metallic versus semiconductillg separation on CoMoCAT samples.

交变流动中压力速度之间相位差对突变截面损失的影响分析

从弱非线性热声理论出发,给出交变流动中突变截面阻力系数的定义以及考察方法。通过PIV(粒子成像测速仪)测量与CFD计算结果的对比,验证了CFD计算结果的可靠性。进而利用CFD模拟考察了交变流动中压力与速度之间相位差对突变截面局部损失的影响,观察到产生这种影响的流场内部流动机制。分析表明,阻力特性确实对声场压力与速度之间的相位差存在依赖性,但这种依赖性会随着非线性的增强而减少。

CFD analysis of pneumatic conveying in a double-tube-socket (DTS (R)) pipe

A pipeline with a bypass is widely used for the pneumatic conveying of material. The double-tube-socket (DTS (R)) technology, which uses a special inner bypass, represents the current state of the art. Here, a new methodology is proposed based on the use of computational fluid dynamics (CFD) to predict the energy consumption of DTS conveying. The predicted results are in good agreement with those from pilot-scale experiments. (C) 2010 Elsevier Inc. All rights reserved.

管道内一氧化碳和空气预热混合物的爆燃特性

为了安全回收煤气余热,实验研究了不同初始温度下的一氧化碳和空气混合气体在设置障碍物的管道中的爆燃特性。测量了爆燃压力和火焰速度,分析了化学当量比和温度对爆燃的影响。结果表明:爆燃压力和火焰速度在障碍物段快速提高;一氧化碳当量比为1.1时爆燃的强度最大;初始温度升高后,压力提高逐渐减缓,最大火焰速度下降,但仍大于550 m/s,传播时间先快速增加后平稳。

Enhancements of the simulation method on the edge effect in resin transfer molding processes

In resin transfer molding processes, small clearances exist between the fiber preform and the mold edges, which result in a preferential resin flow in the edge channel and then disrupt the flow patterns during the mold filling stage. A mathematical model including the effect of cavity thickness on resin flow was developed for flow behavior involving the interface between an edge channel and a porous medium. According to the mathematical analysis of momentum equations in a fully developed rectangular duct and formulations of the equivalent edge permeability, comparing with three-dimensional Navier-Stokes equations, the governing equations were modified in the edge channel. The volume of fluid (VOF) method was applied to track the flow front. A simple case is numerically simulated using the modified governing equations. The effects of edge channel width and cavity thickness on flow front and inlet pressure are analyzed, and the evolution characteristics of simulated results are in agreement with the experimental results. (c) 2007 Elsevier B.V. All rights reserved

Direct formation of form I poly(1-butene) single crystals from melt crystallization in ultrathin films

The morphologies and crystalline structures of melt-crystallized ultrathin isotactic poly(1-butene) films have been studied with transmission electron microscopy and electron diffraction. It is demonstrated that a bypass of form II crystallization can be achieved with an increase in its crystallization temperature. Electron microscopy observations show that melt-grown isotactic poly(1-butene) single crystals have a well-shaped hexagonal form, whereas form I crystals converted from form II display the morphologies of their tetragonal precursors. Electron diffraction results indicate that, instead of the twinned hexagonal pattern of the converted form I crystal, the directly formed form I single crystals exhibit an untwinned hexagonal pattern.