磷酸盐激光玻璃凝胶防潮膜和减反膜

采用溶胶-凝胶方法制备（CH3）2Si（OC2H5）2预聚体涂膜液以及掺入SiO2悬胶体涂膜液改性，采用旋转法在掺钕磷酸盐激光玻璃棒端面涂制防潮膜，热处理后膜层固化。SiO2改性的CH3O防潮膜，热处理后的膜层耐摩擦性能明显改善。然后旋转涂制第二层多空性SiO2减反膜，涂膜胶体通过硅酸乙脂碱催化水解缩聚制得，减反膜的折射率为约1．25，玻璃棒涂膜后激光波长1053nm减少表面反射率6．5％-7．5％，双层膜激光破坏阈值12J／cm^2，1053nm／1ns，膜层表面粗糙度（RMS）2．523nm。直径20

磷酸盐激光玻璃的化学机械抛光

从磷酸盐激光玻璃的成分和结构出发,分析了其化学机械抛光(CMP)机制。通过实验验证了磷酸盐激光玻璃对抛光液pH值具有较强的选择性,在微酸性和中性条件下磷酸盐激光玻璃具有较高的抛光效率,在抛光液中添加pH值调节添加剂会保持抛光环境的酸碱性从而影响抛光效率和抛光质量。通过对pH值和抛光剂浓度的控制获得了均方根(RMS)优于0.6 nm的磷酸盐激光玻璃的超光滑表面。

Highly stable, diode-pumped Nd : YLF regenerative amplifier

We present the design and experimental results for a diode pumped Nd:YLF regenerative amplifier applied to amplify a nanosecond laser pulse. Numerical simulation shows that the maximum output energy and the best stability can be obtained when the regenerative amplifier operates in a saturated mode for all pulse duration and temporal profiles. Using extra post-pulse is a good method to decrease the square-pulse distortion caused by gain saturation effect. The amplifier shows output energy of 4.2mJ with a total energy gain of more than 107 and output energy stability of better than 1% rms. When extra post-pulse is added, square-pulse distortion is decreased from 1.33 to 1.17 for the amplifier that is seeded with an optical pulse of 3 ns.

A Q-swicthed all-solid-state single-longitudinal-mode laser with adjustable pulse-width and high repetition rate

A single-longitudinal-mode (SLM) laser-diode pumped Nd: YAG laser with adjustable pulse width is developed by using the techniques of pre-lasing and changing polarization of birefingent crystal. The Q-switching voltage is triggered by the peak of the pre-lasing pulse to achieve the higher stability of output pulse energy. The output energy of more than 1 mJ is obtained with output energy stability of 3% (rms) at 100 Hz. The pulse-width can be adjusted from 30 ns to 300 ns by changing the Q-switching voltage. The probability of putting out single-longitudinal-mode pulses is almost 100%. The laser can be run over four hours continually without mode hopping.

Effect of water content in sol on optical properties of hybrid sol-gel derived TiO2/SiO2/ormosil film

Sol-gel derived TiO2/SiO2/ormosil hybrid planar waveguides have been deposited on soda-lime glass slides and silicon substrates, films were heat treated at 150 degreesC for 2 h or dried at room temperature. Different amounts of water were added to sols to study their impacts on microstructures and optical properties of films. The samples were characterized by m-line spectroscopy, Fourier transform infrared spectroscopy (FT-IR), UV/VIS/NIR spectrophotometer (UV-vis), atomic force microscopy (AFM), thermal analysis instrument and scattering-detection method. The refractive index was found to have the largest value at the molar ratio H2O/OR = 1 in sol (OR means -OCH3, -OC2H5 and -OC4H9 in the sol), whereas the thickest film appears at H2O/OR = 1/2. The rms surface roughness of all the films is lower than 1.1 nm, and increases with the increase of water content in sol. Higher water content leads to higher attenuation of film. (C) 2004 Elsevier B.V. All rights reserved.

Study on the hydrolytic property and thermal stability of LiAlO2 substrate

The hydrolytic property and thermal stability of LiAlO2 (LAO), important factors for its application, were examined by AFM and X-ray rocking curve. We found that H2O may be deleterious for LAO surface polishing when the root mean square (RMS) value is less than 1 nm. However, when the RMS value is more than 1 nm it may be useful for LAO polishing. (100)-plane LAO substrates are annealed in the range of 850-900 degrees C in flux N-2, Slick AlN layer probably is produced on the substrate surface. M-plane GaN layer has grown on the substrate by metal-organic chemical vapor deposition (MOCVD) method. Theses results show that LiAlO2 crystal is a promising substrate of fabricating high-efficiency LEDs by MOCVD. (c) 2006 Elsevier B.V. All rights reserved.

提拉法Ti:LiAlO_2晶体的生长、缺陷及N_2退火研究

本文采用提拉法成功地生长了钛掺杂浓度为0.1%原子分数的LiAlO2单晶体,借助光学显微镜,结合化学腐蚀法,对Ti:LiAlO2晶体(100)面空气退火前后的缺陷特征进行了研究,用AFM观测了(100)面晶片在不同温度下流动N2气氛退火过的表面形貌。结果表明:Ti:LiAlO2晶体(100)面的位错腐蚀坑是底面为平行四边形的锥形坑,位错密度约为5.0×104cm-2,900℃空气退火后晶片表面的位错腐蚀坑变大;N2退火能显著影响晶片的表面形貌,当退火温度为900℃时,晶片的均方根粗糙度(RMS)达到最低值

化学抛光和退火对钛酸锶基片表面改性研究

Atomic force microscopy (AFM) was applied to study the surface morphology of SrTiO3 substrates which were polished by traditional mechanical and chemical mechanical method respectively. The influence of anneal was also studied. Results show that the RMS of CMP STO substrates can be 0.214 nm. Compared the rocking curve of the unannealed STO substrates with the annealed ones, it indicates that anneal can improve the crystal quality.

Structural and optical properties of nonpolar m-plane GaN and GaN-based LEDs on gamma-LiAlO2

We report the structural and optical properties of nonpolar m-plane GaN and GaN-based LEDs grown by MOCVD on a gamma-LiAlO2 (100) substrate. The TMGa, TMIn and NH3 are used as sources of Ga, In and N, respectively. The structural and surface properties of the epilayers are characterized by x-ray diffraction, polarized Raman scattering and atomic force microscopy (AFM). The films have a very smooth surface with rms roughness as low as 2nm for an area of 10 x 10 mu m(2) by AFM scan area. The XRD spectra show that the materials grown on gamma-LiAlO2 (100) have < 1 - 100 > m-plane orientation. The EL spectra of the m-plane InGaN/GaN multiple quantum wells LEDs are shown. This demonstrates that our nonpolar LED structure grown on the gamma-LiAlO2 substrate is indeed free of internal electric field. The current voltage characteristics of these LEDs show the rectifying behaviour with a turn on voltage of 1-3 V.

Investigation on microstructure and optical properties of titanium dioxide coatings annealed at various temperature

TiO2 coatings were prepared on fused silica with conventional electron beam evaporation deposition. After TiO2 thin films were annealed at different temperatures for 4 h, several properties were investigated by X-ray diffraction (XRD), spectrometer.. photoelectron spectroscopy (XPS) and AFM. It was found that with the annealing temperature increasing, the transmittance of TiO2 coatings decreased, and the cutoff wavelength shifted to long wavelength in near ultraviolet band. Especially, when coatings were annealed at high temperature, the optical loss is very serious, which can be attributed to the scattering and the absorption of TiO2 coatings. XRD patterns revealed that only anatase phase was observed in TiO2 coatings regardless of the different annealing temperatures. XPS results indicated that the fine chemical shift of TiO2 2p(1/2) should be attributed to existence of oxygen vacancies around Ti+4 ion. The investigation on surface morphology by AFM showed that the RMS of titania thin films gradually increases from less than 0.40 nm to 5.03 nm and it should be ascribed to the growth of titanium dioxide grain size with the increase of annealing temperature. (C) 2005 Elsevier B.V. All rights reserved.

测量薄膜微粗糙度的总积分散射仪

介绍了一种检测光学薄膜表面总积分散射（TIS）分布的总积分散射仪。对仪器的基本结构、理论基础、测量原理以及系统性能等进行了阐述，提出了抑制系统噪音和提高测量精度的有效措施。利用该仪器对K9基底上的银（Ag）膜和氧化锆（ZrO2）薄膜进行了测量，并根据标量散射理论得到了表面均方根（RMS）粗糙度。利用光学轮廓仪和原子力显微镜（AFM）分别测量了上述Ag膜和ZrO2薄膜的表面均方根粗糙度，并与总积分散射仪所得的粗糙度进行了比较。结果表明，根据测量的薄膜表面总积分散射计算得到的表面均方根粗糙度与光学轮廓仪及原子

电子束蒸发氧化锆薄膜的粗糙度和光散射特性

利用电子束蒸发工艺，以Ag层为衬底，沉积了中心波长为632．8nm的氧化锆（ZrO2）薄膜，膜层厚度在80-480nm范围内变化．研究了不同厚度样品的粗糙度变化规律和表面散射特性．结果发现，随着膜层厚度的逐渐增加．其表面均方根（RMS）粗糙度和总积分散射（TIS）均呈现出先减小后增大的趋势．利用非相关表面粗糙度的散射模型对样品的TIS特性进行了理论计算，所得结果与测量结果相一致．

Annealing effects on electron-beam evaporated Al2O3 films

The effects of post-deposited annealing on structure and optical properties of electron-beam evaporated Al2O3 single layers were investigated. The films were annealed in air for 1.5 h at different temperatures from 250 to 400 degrees C. The optical constants and cut-off wavelength were deduced. Microstructure of the samples was characterized by X-ray diffraction (XRD). Profile and surface roughness measurement instrument was used to determine the rms surface roughness. It was found that the cut-off wavelength shifted to short wavelength as the annealing temperature increased and the total optical loss decreased. The film structure remained amorphous even after annealing at 400 degrees C temperature and the samples annealed at higher temperature had the higher rms surface roughness. The decreasing total optical loss with annealing temperature was attributed to the reduction of absorption owing to oxidation of the film by annealing. Guidance to reduce the optical loss of excimer laser mirrors was given. (c) 2004 Elsevier B.V. All rights reserved.

退火对电子束热蒸发Al2O3薄膜性能影响的实验研究

用电子束热蒸发方法镀制了Al2O3材料的单层膜，对它们在空气中进行了250～400℃的高温退火。对样品的透射率光谱曲线进行了测量，计算了样品的消光系数、折射率和截止波长。通过X射线衍射仪(XRD)测量分析了薄膜的微观结构，采用表面轮廓仪测量了样品的表面均方根粗糙度。结果发现随着退火温度的提高光学损耗下降，薄膜结构在退火温度为400℃时仍然为无定形态，样品的表面粗糙度随退火温度的升高而增加。引起光学损耗下降起主导作用的是吸收而不是散射，吸收损耗的下降主要是由于退火使材料吸收空气中的氧而进一步氧化，从而使薄膜

热舟蒸发LaF_3薄膜的紫外性能研究

研究了沉积温度对热舟蒸发氟化镧薄膜结构和光学性能的影响,沉积温度从200℃上升到350℃,间隔为50℃.采用分光光度计测量了样品的透射率和反射率光谱曲线,并在此基础上进行了光学损耗、光学常数以及带隙和截止波长的计算.采用表面轮廓仪进行了表面形貌和表面粗糙度的标定,采用X射线衍射(XRD)方法测量了不同沉积温度下样品的微结构.发现在短波长波段,随着沉积温度的升高,光学损耗增加,晶粒尺寸增大,表面粗糙度略有增加.不过散射损耗在光学损耗中所占比例均很小,光学损耗的增加主要由吸收损耗引起.随着沉积温度的升高,折射率与消光系数增大,带隙变小,相对应的截止波长向长波方向移动.