Influences of reactor pressure of GaN buffer layers on morphological evolution of GaN grown by MOCVD

The morphological evolution of GaN thin films grown on sapphire by metalorganic chemical vapor deposition was demonstrated to depend strongly on the growth pressure of GaN nucleation layer (NL). For the commonly used two-step growth process, a change in deposition pressure of NL greatly influences the growth mode and morphological evolution of the following GaN epitaxy. By means of atomic force microscopy and scanning electron microscope, it is shown that the initial density and the spacing of nucleation sites on the NL and subsequently the growth mode of FIT GaN epilayer may be directly controlled by tailoring the initial low temperature NL growth pressure. A mode is proposed to explain the TD reduction for NL grown at relatively high reactor pressure. (C) 2003 Elsevier B.V. All rights reserved.

Scattering-parameter measurements of laser diodes

An accurate and simple technique for measuring the input reflection coefficient and the frequency response of semiconductor laser diode chips is proposed and demonstrated. All the packaging parasitics could be obtained accurately using a calibrated probe, and the impedance of the intrinsic diode chip is deduced from the directly measured reflection coefficient. The directly measured impedance of a laser diode is affected strongly by the short bond wire. In the frequency response (S(2)1) measurements of semiconductor laser diode chips, the test fixture consists of a microwave probe, a submount, and a bond wire. The S-parameters of the probe could be determined using the short-open-match (SOM) method. Both the attenuation and the reflection of the test fixture have a strong influence on the directly measured frequency response, and in our proposed technique, the effect of test fixture is completely removed.

Phase uncertainty in calibrating microwave test fixtures

The problem of phase uncertainty arising in calibration of the test fixtures is investigated in this paper, It is shown that the problem exists no matter what kinds of calibration standards are used. It is also found that there is no need to determine the individual S-parameters of the test fixtures. In order to eliminate the problem of phase uncertainty, three different precise (known) reflection standards or one known reflection standard plus one known transmission standard should be used to calibrate symmetrical test fixtures. For the asymmetrical cases, three known standards, including at least one transmission standard, should be used. The thru-open-match (TOM) and thru-short-match (TSM) techniques are the simplest methods, and they have no bandwidth limitation. When the standards are imprecise (unknown), it is recommended to use any suitable technique, such as the thru-reflect-line, line-reflect-line, thru-short-delay, thru-open-delay,line-reflect-match, line-reflect-reflect-match, or multiline methods, to accurately determine the values of the required calibration terms and, in addition, to use the TOM or TSM method with the same imprecise standards to resolve the phase uncertainty.

a backtracking search tool for constructing combinatorial test suites

Combinatorial testing is an important testing method. It requires the test cases to cover various combinations of parameters of the system under test. The test generation problem for combinatorial testing can be modeled as constructing a matrix which has certain properties. This paper first discusses two combinatorial testing criteria: covering array and orthogonal array, and then proposes a backtracking search algorithm to construct matrices satisfying them. Several search heuristics and symmetry breaking techniques are used to reduce the search time. This paper also introduces some techniques to generate large covering array instances from smaller ones. All the techniques have been implemented in a tool called EXACT (EXhaustive seArch of Combinatorial Test suites). A new optimal covering array is found by this tool.

Frequency limitation in calibrating microwave test fixtures

The problem of frequency limitation arising in calibration of the test fixtures is investigated in this paper. It is found that at some frequencies periodically, the accuracy of the methods becomes very low, and. the denominators of the expressions of the required S-parameters approach zero. This conclusion can be drawn whether-the test fixtures, are symmetric or not. A good agreement between theory and experiment is obtained.

Synthesis of chiral stationary phases with radical polymerization reaction of cellulose phenylcarbamate derivatives and vinylized silica gel

Cellulose phenylcarbamate derivatives having methacrylate groups were synthesized with regioselective and non-regioselective procedures. These derivatives were chemically immobilized onto a vinylized silica gel, respectively, via a radical co-polymerization reaction. The immobilization was efficiently attained using a small amount of AIBN. The chiral recognition abilities of the prepared chiral stationary phases (CSPs) were evaluated by HPLC resolution of test enantiomers. It was observed that most of the enantiomers were completely resolved with markedly high column efficiency of 30,000-40,000 plates per metre for the eluted peaks. The effect of the amount of methacrylolyl chloride used for preparation on resolution was investigated. A direct comparison of the chiral recognition ability was made on the regioselectively and non-regioselectively prepared CSPs. In addition, the chemically bonded-type of CSPs were found to be relatively stable with addition of solvents such as tetrahydrofuran (THF) and chloroform into the mobile phase, which can lead to the dissolution of cellulose derivatives on the coated CSPs. Thus the choice of solvents used as the mobile phase is greatly extended and better resolution of several test enantiomers was observed on the prepared CSPs with THF and chloroform as a composition in the mobile phase. The batch-to-batch and run-to-run reproducibility was also discussed on the newly prepared CSPs. (C) 2004 Elsevier B.V. All rights reserved.

automated test program generation for an industrial optimizing compiler

Association for Computing Machinery, ACM; IEEE; IEEE Computer Society; SIGSOFT

Composites of poly(lactide-co-glycolide) and the surface modified carbonated hydroxyapatite nanoparticles

To improve the mechanical properties of the composites of poly(lactide-co-glycolide) (PLGA, LA/GA = 80/20) and the carbonate hydroxyapatite (CHAP) particles, the rice-form or claviform CHAP particles with 30-40 nm in diameter and 100-200 nm in length were prepared by precipitation method. The uncalcined CHAP particles have a coarse surface with a lot of global protuberances, which could be in favor of the interaction of the matrix polymer to the CHAP particles. The nanocomposites of PLGA and surface grafted CHAP particles (g-CHAP) were prepared by solution mixing method. The structure and properties of the composites were subsequently investigated by the emission scanning electron microscopy, the tensile strength testing, and the cell culture. When the contents of g-CHAP were in the range of 2-15 wt %, the PLGA/g-CHAP nanocomposites exhibited an improved elongation at break and tensile strength. At the 2 wt % content of g-CHAP, the fracture strain was increased to 20%) from 4-5% for neat PLGA samples. Especially at g-CHAP content of 15 wt %, the tensile strength of PLGA/g-CHAP composite was about 20% higher than that of neat PLGA materials. The tensile moduli of composites were increased with the increasing of filler contents, so that the g-CHAP particles had both reinforcing and toughening effects on the PLGA composites. The results of biocompatibility test showed that the higher g-CHAP contents in PLGA composite facilitated the adhesion and proliferation properties of osteoblasts on the PLGA/g-CHAP composite film.

Comparative growth and viability of hybrids between two populations of Chinese shrimp (Fennropenaeus chinensis)

Fenneropenaeus chinensis is confined to the Yellow Sea and Bohai Sea in China and the West Coast of the Korean Peninsula. Intra- and intercross populations were produced between Rushany (YP) and Korean (KN) populations. Seven traits were recorded. The heterosis of hybrids was computed and comparison between treatments was performed by ANOVA. At the fourth month after post-larvae, six indexes of growth trait and viability showed a range of heterosis, ranging from 0.514% to 14.950%. At the fifth month after post-larvae, six indexes of growth trait and viability ranged from -9.000% to 19.090%. The negative heterosis was observed in CL, HST and viability. The heterosis of KN female xYP male tended generally to increase as the age of the Chinese shrimp increased while the heterosis of YP female xKN male tended to decrease. The results indicated that the viability of reciprocal hybrids were not significantly different (P > 0.05) from their parents during the experiment. The result of ANOVA indicated that the F1 hybrids were significantly different (P < 0.05) in WST and TW at the fourth month. The multiple comparisons of LSD test indicated that the hybrids of YP female xKN male were significantly different (P < 0.05) from their parents in TW. The hybrids of YP female xKN male were significantly different (P < 0.05) from the other three combinations in WST. At the fifth months, the F1 hybrids had significant difference (P < 0.05) in body weight while other traits showed no significant differences (P > 0.05) from their parents. The multiple comparisons of LSD test indicated that the hybrids of KN female xYP male were significantly different (P < 0.05) from the KN parents in TW. The results indicate that in experimental conditions, the F-1 hybrids created from two populations of Chinese shrimp showed a certain level of heterosis for growth performance and viability. The crossing scheme may improve growth performance and viability in Chinese shrimp, but the improvement may be limited because effective crossbreeding requires the maintenance of pure, preferably inbred, lines and possibly involves specialized sire and dam lines. Therefore, the exploitation of heterosis through single crossbreeding in Chinese shrimp is of limited utility in practical commercial shrimp aquaculture in spite of the potential of significant heterosis. The crossbreeding of different populations can be applied in the establishment of base populations.

广西合山固体废弃物制备地质聚合物胶凝材料

Geopolymer gelatinous material was prepared by ferroalloy slag (signed with NKT in laboratory) and circulating fluidization bed slag (CFB slag, signed with NM in laboratory) produced from Heshan city, Guangxi zhuang autonomous region, China. The mechanical properties of the geopolymer made of high content ferroalloy slag can reach the standard of 42.5# portland blastfurnace-slag cement, and it’s processing technology is more simple and not need of mill and burn and will not produce harmful gas. By means of chemical and XRD analyses, it is concluded that NKT is a kind of acidity water-granulated slag with better activation and fit to be activated by alkali activators. Low-cost industrial gypsum (signed with NG in laboratory), analytic reagent oxide(signed with NH in laboratory) and sulfate(signed with NS in laboratory) were selected as alkali activation in the experiment. The results showed NH is a good alkali activator for NKT. Both NH and NG can activate ferroally slag’s activities, but NS can’t alone. The activation effect of superimposing activation of NH and NG excel by separateness. Based on those experiments, optimization compounds were carried out: (1) NKT: NH: NG = 80: 10: 10 and (2) NM: NKT: NS: NG: NH = 10: 70: 2: 8: 10。. The soundness of the test blocks is good by boiling examination. Through XRD, SEM, IR, NMR analyses of geopolymer, the reaction mechanism of geopolymer prepared by alkalescent activating in solid wastes was discussed in the thesis first. It is point out, there is difference in reaction mechanism between traditional geopolymer preparation and the preparation of alkalescent activating solid wastes because NG is a industry product. There is the similar process of depolymerization and reunion of Si-O bond. The latter preparation process generate new subtance but the former doesn’t. In the experiment, we found a performance of NKT that the water requirement of normal consistency of geopolymer reduces with increasing content of NKT. The result shows NKT has some ability to reduce water requirement. The performance is worthy of further research and utilization. Making use of solid wastes to prepare geopolymer, not only can settle environment problem caused by a great deal of dump of NKT, but also settle the shortage of natural resources. Moreover it could take economic, environmental and social benefits and settle thoroughly contradiction in the environment protection and regional economy development and promote circulation economy development.