目标反射特性对激光测距的影响

针对非合作小目标激光测距系统,目标表面的反射特征对激光回波信号有很大的影响。建立测量表面双向反射分布函数(BRDF)的装置,对常用的两种热控材料——白漆涂层和F36多包层,测量了其在1064 nm波长下的双向反射分布函数。得出了白漆涂层镜面反射很小,散射角较大,利于各方向接收回波信号;而F36多包层镜面反射很强,散射角-2°~2°,不利于探测。通过由表面BRDF与由朗伯散射计算得到的最小接收功率的比较,得出了入射角大于45°入射白漆涂层时,回波信号较小;大于2°入射F36多包层时,没有回波信号。

Temperature characteristics of optical parameters of phthalocyanine LB films and spin-coated films

The LB films and spin-coated films of tetra-neopentoxy phthalocyanine zinc (TNPPcZn) were prepared and annealed at different temperatures. Their refractive index (n) and extinction coefficient (k) were measured by p-polarized reflectance. The similar value of n and k, as well as similar changing tendency of it and k at varied annealing temperatures, was found between LB films and spin-coated films. In addition, the absorption curves of TNPPcZn LB films and spin-coated films in visible range at different annealing temperature were investigated. The results indicate that the changing tendency of the extinction coefficient of two kinds of TNPPcZn films obtained from two methods mentioned above were coincident. When the annealing temperature increased to 150 degrees C, the monomers of TNPPcZn films transformed to aggregates, n(f) and k(f) of the films increased. Further, n(f) and k(f) decreased as aggregates changed back to monomers again at the annealing temperature of 300 degrees C. The experimental results coincide well with the theoretical analysis. (C) 2004 Elsevier B.V. All rights reserved.

Optical and surface properties of hybrid TiO2/ormosil planar waveguide prepared by the sol-gel process

Two kinds of silanes, 3-glycidoxypropyltrimethoxysilane (GLYMO) and 3-trimethoxysililpropylmethacrylate (TMSPM), were used to prepare ormosil waveguide films by the sol-gel method. Thirty percent Ti(OBu)(4) and 70% silane were contained in the precursor sets. The properties of films were measured by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), UV/VIS/NIR spectrophotometer (UV-vis), atomic force microscopy (AFM), m-line and scattering-detection method. The films from GLYMO and TMSPM precursors exhibit similar thickness (2.58 mu m for GLYMO, 2.51 mu m for TMSPM) and refractive index (1.5438 for GLYMO, 1.5392 for TMSPM, lambda=632.8 nm), but the film from TMSPM precursor has higher propagation loss (1.024 dB/cm, lambda=632.8 nm) than the film prepared from GLYMO (0.569 dB/cm, lambda=632.8 nm). Furthermore, the film prepared from TMSPM is easy to be opaque and cracks during coating whereas the same phenomenon was not found for the film prepared with GLYMO. It is confirmed that GLYMO is a better precursor than TMSPM for waveguide film preparation. (C) 2005 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Nd：YAG透明陶瓷的制备与激光输出

成功制备了高质量的Nd：YAG透明陶瓷，激光测试样品的尺寸为3mm×3mm×3mm,双面抛光、未镀膜，最高连续输出能量为1003mW，斜率效率为14％．

水热法生长复合钛宝石激光晶体

水热法生长了复合钛宝石(Al2O3／Ti：Al2O3)激光晶体．对外层Al2O3X射线ω扫描表明其晶体质量很高．外层生长的Al2O3和内部的钛宝石激光棒结合牢固、紧密，因而能适应高强度泵浦所带来的激光介质内部的热应力．复合激光晶体界面层带来的光损耗很小．就我们所知，这是首次用水热法生长复合激光晶体．

高度C轴取向的ZnO膜的低温水热法制备

在预先镀有ZnO纳米层的（0001）蓝宝石衬底上利用低温水热法制备出ZnO薄膜。SEM和XRD显示此ZnO膜是由六棱柱状阵列构成的，基于蓝宝石衬底生长，具有高度的c轴择优取向，且（0004）摇摆曲线的FWHM达到1．8°。并发现了在水热溶液中加入一定量六次甲基四胺可以调节六棱柱状ZnO尺寸比例。

Low-temperature hydrothermal growth of oriented [0001] ZnO film

Well-aligned ZnO films have been successfully prepared by using low-temperature hydrothermal approach on (0001) sapphire substrates that were pre-coated with a ZnO nano-layer by dip-coating. The characterizations of scanning electron microscopy (SEM) and X-ray diffraction (XRD) indicate that the ZnO films consist of hexagonal rods that grow along the c axis based on the sapphire substrates. It is found that the size of ZnO rods can be adjusted by an aqueous solution with some methenamine. (c) 2006 Elsevier B.V. All rights reserved.

基底微缺陷对介质薄膜光学性能影响的理论研究

基于非均匀膜理论提出一种存在微缺陷的介质基底的折射率分层模型，将基底依次分为表面层、亚表面层和体材料层，其中表面层和亚面层分别等效为折射率服从统计分布的非均匀膜，将它们分别再次细分为N1和N2个子层，每一子层均视为均匀介质膜．应用光学薄膜特征矩阵法对其进行理论分析，并对单层介质膜的光学性能进行数值计算．研究结果表明：基底的表面和亚表面微缺陷改变了薄膜和基底的等效折射率，导致了准Brewster角和组合反射率与理想情形的偏离．同时这些微缺陷也改变了光在薄膜和基底中的传播特性，因此反射相移和相位差均偏离理想情

HfO2 膜料中的杂质对薄膜损伤及性能的影响

By analysis of impurity elements in HfO2 coating material, the influence of main impurity elements on the characteristic of coatings were studied. The results indicate that the metal elements and absorptive dielectric elements damage the HfO2 coatings. The more the Zr element content is, the more the absorption is for the coatings in ultraviolet wave. The negative ion element will become the gas source center and form an ejection in the process of evaporation of coating material, so decrease the damage threshold of the coatings.

微缺陷对薄膜滤光片环境稳定性的影响

用热蒸发方法沉积了薄膜滤光片．并将样品分别在去离子水中浸泡10天和30天．通过分光光度计、光学暗场显微镜、及扫描电子显微镜等多种测试手段，对诱导透射滤光片在潮湿环境下的稳定性进行了研究．实验发现，在潮湿环境下滤光片产生的膜层分离都是从薄膜中微缺陷点处开始发生和发展的，微缺陷是影响滤光片环境稳定性的重要原因之一，其中杂质和针孔是滤光片中两种最常见的微缺陷．EDS能谱分析进一步表明，薄膜中杂质缺陷成分即为Al2O3膜料本身，所以不能推测，薄膜沉积中的喷溅可能是微缺陷产生的根本原因，抑制喷溅可以有效提高薄膜滤光

斜角入射沉积法制备渐变折射率薄膜的理论探讨

从理论上分析了单一膜料倾斜入射沉积时的折射率与填充密度的关系，给出了三种不同的表达式；然后从正变和负变、完整周期和存在半周期以及不同的周期数等几个方面探讨了膜层的填充密度按照线性变化时的渐变折射率薄膜的光学特性，并将折射率的不同理论表达式对光学特性的影响进行了对比，最后讨论了单一膜料倾斜入射沉积渐变折射率薄膜的方法、填充密度线性变化时的渐变折射率薄膜的应用及制备中需要进一步解决和处理的问题．

磁控反应溅射法制备渐变折射率薄膜的模型分析

阐述了磁控反应溅射法制备渐变折射率薄膜的机理；探讨了磁控反应溅射法制备渐变折射率薄膜的理论模型，给出了渐变折射率薄膜的折射率与反应气体分压的关系，在一定的沉积参数下，由要得到的膜层折射率随膜层几何厚度的变化规律可推导出反应气体分压比随时间的变化规律；最后以制备折射率线性变化的薄膜为例说明了如何推导得到反应气体分压比随时间的变化规律．

共蒸法制备非均匀膜的速率控制分析

渐变折射率薄膜，又称为非均匀膜。利用德鲁德理论分析了混合介质膜的介电常量与各个膜料的介电常量之间的关系，介绍了共蒸法制备非均匀膜的制备机理。对混合膜的沉积速率为两种膜料的沉积速率之和的情况，分别从两种膜料的单分子体积是否相等和总的沉积速率是否为常数两个方面，探讨了双源共蒸法制备的非均匀膜的折射率分布规律与膜料的沉积速率之间的关系，并给出了几种常见的折射率分布如线性变化、正弦变化、指数变化和双曲变化规律的膜料沉积速率表达式。最后以混合介质膜的总沉积速率为常数、折射率按照线性变化为例进行了说明。

Design and properties analysis of multi-layer dielectric used in pulse compressor gratings

Used in chirped-pulse amplification system and based on multi-layer thin film stack, pulse compressor gratings (PCG) are etched by ion-beam and holographic techniques. Diffraction efficiency and laser-induced damage threshold rely on the structural parameters of gratings. On the other hand, they depend greatly on the design of multi-layer. A theoretic design is given for dielectric multi-layer, which is exposed at 413.1 nm and used at 1053 nm. The influences of coating design on optical characters are described in detail. The analysis shows that a coating stack of H3L (H2L) (boolean AND) 9H0.5L2.01H meets the specifications of PCG well. And there is good agreement of transmission between experimental and the theoretic design. (c) 2005 Elsevier GmbH. All rights reserved.

Laser-induced damage morphology of high-reflective optical coatings

Two different kinds of 1064 nm high-reflective (HR) coatings, with and without SiO2 protective layer, were prepared by electron beam evaporation. Three-dimensional damage morphology, caused by a Nd:YAG pulsed laser, was investigated for these HR coatings. Development of laser-induced damage on HR coatings was revealed by both temperature field calculation and discrete meso-element simulation. Theoretical results met experimental very well. (C) 2004 Elsevier B.V. All rights reserved.