Influence of substrate temperature on properties of MgF2 coatings

Thermal boat evaporation was employed to prepare MgF2 single-layer coatings upon both JGS1 and UBK7 substrates at different substrate temperatures. Microstructure, transmittance and residual stress of these coatings were measured by X-ray diffraction, spectrophotometer, and optical interferometer, respectively. Measurement of laser induced damage threshold (LIDT) of the samples was performed at 355 nm, 8 ns pulses. The results showed that high substrate temperature was beneficial to crystallization of the film. Above 244 degrees C, the refractive index increased gradually with the substrate temperature rising. Whereas, it was exceptional at 210 degrees C that the refractive index was higher than those deposited at 244 and 277 degrees C. The tensile residual stresses were exhibited in all MgF2 films, but not well correlated with the substrate temperature. In addition, the stresses were comparatively smaller upon JGS1 substrates. A tendency could be seen that the LIDTs reached the highest values at about 244 degrees C, and the films upon JGS1 had higher LIDTs than those upon UBK7 substrates at the same temperature. Meanwhile, the damage morphologies showed that the laser damage of the coating resulted from an absorbing center at the film-substrate interface. The features of the damages were displayed by an absorbing center dominated model. Furthermore, the reason of the difference in LIDT values was discussed in detail. (C) 2007 Elsevier B.V. All rights reserved.

Effects of annealing on laser-induced damage threshold of TiO2/SiO2 high reflectors

The mechanism of improving 1064 nm, 12 ns laser-induced damage threshold (LIDT) of TiO2/SiO2 high reflectors (HR) prepared by electronic beam evaporation from 5.1 to 13.1 J/cm(2) by thermal annealing is discussed. Through optical properties, structure and chemical composition analysis, it is found that the reduced atomic non-stoichiometric defects are the main reason of absorption decrease and LIDT rise after annealing. A remarkable increase of LIDT is found at 300 degrees C annealing. The refractive index and film inhomogeneity rise, physical thickness decrease, and film stress changes from compress stress to tensile stress due to the structure change during annealing. (c) 2007 Elsevier B.V. All rights reserved.

Preparation and characterization of nanostructured ZrO2 thin films by glancing angle deposition

ZrO2 films were prepared by electron beam evaporation with glancing angle deposition (GLAD) technique. The as-deposition and annealed ZrO2 films are all amorphous, different from that deposited at normal incidence. Due to the shadowing effect, a highly orientated structure composed of slanted columns formed, and the obtained films became the mixture of slanted columns and voids. The relationship among the effective refractive index, packing density and flux incident angle was investigated. The refractive index and packing density of ZrO2 films decrease with the increase of the incident angle. The in-plane birefringence of GLAD ZrO2 films was calculated. At the packing density of 0.576, the maximum birefringence is 0.037. (c) 2006 Elsevier B.V. All rights reserved.

三硼酸锂晶体上1064 nm, 532 nm, 355 nm三倍频增透膜的设计

采用矢量法设计了三硼酸锂晶体上1064 nm、532 nm和355 nm三倍频增透膜,结果表明1064 nm、532 nm和355 nm波长的剩余反射率分别为0.0017％、0.0002％和0.0013％。根据误差分析,薄膜制备时沉积速率精度控制在＋5.5％时,1064 nm、532 nm和355 nm波长的剩余反射率分别增加至0.20％、0.84％和1.89％。当材料折射率的变化控制在＋3％时,1064 nm处的剩余反射率增大为0.20％,532 nm和355 nm处分别达0.88％和0.24％。与薄膜

Y_2O_3稳定ZrO_2薄膜的结构和光学特性

用电子束蒸发法制备出四种不同Y2O3含量的Y2O3稳定ZrO2（YSZ）薄膜,用X射线衍射和透射光谱测定薄膜的结构和光学性能.结果表明：随着Y2O3含量的增加,ZrO2薄膜从单斜相向高温相（四方相和立方相）转变,获得了结构稳定的YSZ薄膜;YSZ薄膜的晶粒尺寸都比ZrO2薄膜的大,但随着Y2O3加入量的增加,晶粒尺寸有减小的趋势,薄膜表面也趋向光滑平整.所有YSZ薄膜的透射谱线都与ZrO2薄膜相似,在可见光和红外光区都有较高的透过率.Y2O3的加入还可以改变薄膜的折射率,在一定范围内可得到所需的任意折射率

沉积温度对LaF3薄膜性能的影响

abstract {LaF₃ single-layer coatings were prepared by thermal boat evaporation at the deposition temperatures of 189, 255, 277 and 321°C respectively. The crystal structures of the coatings were characterized by X-ray diffraction (XRD). A spectrophotometer was employed to measure its transmittance. Moreover, refractive index, extinction coefficient and cut-off wavelength were obtained from the measured transmittance spectral curve. The residual stress was evaluated by the Stoney's equation and optical interferometer. Laser induce damage threshold (LIDT) was performed by a tripled Nd:YAG laser system. The results show that the crystallization status becomes better with the deposition temperature increasing. Correspondingly, the grain size also gets larger. Meanwhile, the coatings become more compact and the refractive index increases. However, the absorption of coatings seriously rises and the cut-off wavelength drifts to the long wave. In addition, the residual stress also increases and the intrinsic stress plays a determinant role in the coating. The LIDT of the coating also enhances at high temperature.}

渐变折射率薄膜的分层评价探讨

首先阐述了将渐变折射率薄膜细分为多层均匀薄膜的分层介质理论，接着给出了一种获得最佳分层数目的分层评价方法，最后以线性变化渐变折射率薄膜为例说明了如何优化获得渐变折射率薄膜的分层数目．研究发现：渐变折射率薄膜的分层数目与薄膜的厚度和薄膜的折射率变化快慢有关，在一定的折射率变化范围内，渐变折射率薄膜的分层数目随着薄膜厚度的增加先减小后增大．

沉积速率对热舟蒸发LaF3薄膜性能的影响

用热舟蒸发方法在不同的沉积速率下制备了LaF3单层膜,并对部分单层膜进行了真空退火。分别采用X射线衍射(XRD),Lambda 900 光谱仪和355 nm Nd∶YAG脉冲激光测试了薄膜的晶体结构、透射光谱和激光损伤阈值(LIDT),并通过透射光谱计算得到样品的折射率和消光系数。实验结果表明,增大沉积速率有利于LaF3薄膜的结晶和择优生长,可以提高薄膜的致密性和折射率,但薄膜的抗激光损伤能力有所下降;沉积速率太大,又会恶化薄膜的结晶性能,同时薄膜中产生大量孔洞,薄膜的机械强度降低,导致薄膜的折射率减小和

4H-SiC基底Al_2O_3/SiO_2双层减反射膜的设计和制备

在4H-SiC基底上设计并制备了Al2O3/SiO2紫外双层减反射膜,通过扫描电镜(SEM)和实测反射率谱来验证理论设计的正确性。利用编程计算得到Al2O3和SiO2的最优物理膜厚分别为42.0nm和96.1nm以及参考波长λ=280nm处最小反射率为0.09%。由误差分析可知,实际镀膜时保持双层膜厚度之和与理论值一致有利于降低膜系反射率。实验中应当准确控制SiO2折射率并使Al2O3折射率接近1.715。用电子束蒸发法在4H-SiC基底上淀积Al2O3/SiO2双层膜,厚度分别为42nm和96nm。SEM截面图表明淀积的薄膜和基底间具有较强的附着力。实测反射率极小值为0.33%,对应λ=276nm,与理论结果吻合较好。与传统SiO2单层膜相比,Al2O3/SiO2双层膜具有反射率小,波长选择性好等优点,从而论证了其在4H-SiC基紫外光电器件减反射膜上具有较好的应用前景。

Influence of oxygen plasma treatment on properties of ZrO2 films prepared by e-beam evaporation techniques

Zirconia films were prepared by e-beam evaporation, and oxygen plasma treatment was used to modify film properties. Spectrophotometry, x-ray diffractometry (XRD), and atomic force microscopy were used to characterize refractive index, extinction coefficient, rnicrostructure, and surface roughness, respectively. The experimental results indicate that both refractive index and extinction coefficient of the films were reduced slightly after oxygen plasma treatment, with the decrease of intrinsic stress and surface roughness. From XRD spectra, the intensity decrease of the T(110) diffraction peak was clearly observed after the treatment, which was caused by the restructuring of the film atoms. (C) 2008 Elsevier Ltd. All rights reserved.

低损耗193nm反射膜的设计

采用1/4规整膜系,从电场强度、吸收损耗及散射损耗的分布几个方面,对影响193 nm反射膜性能的因素进行了分析。以分析结果为基础,对低损耗193 nm反射膜的设计进行了探讨。结果表明:在空气侧的外膜层中电场强度较大,随着层数向内过渡,电场强度迅速减小;高折射率材料膜层的吸收损耗明显高于低折射率材料膜层的吸收损耗,而且靠近空气侧最外层的高折射率膜层的吸收损耗最大;按由外层向内层过渡的方向,吸收损耗迅速减小,减小的速度与高低折射率材料折射率的比值相关;表面散射损耗与两种材料的折射率比值成正比,但折射率比值减小后只能通过增加膜层数来获得一定的反射率,而这样又会使表面粗糙度增加,并且引入其它的损耗。因此,选择折射率差值适当大一些的材料对降低散射损耗是有利的。设计了27层膜堆的193 nm反射膜,设计反射率在98%以上。

LiB3O5晶体上四倍频增透膜设计

采用矢量法设计了三硼酸锂（LiB3O5，LBO）晶体上1064nm、532nm、355nm和266nm四倍频增透膜．结果表明，在1064nm、532nm、355nm和266nm波长的剩余反射率分别为0．0019％、0．0031％、0．0061％和0．0047％．根据容差分析，薄膜制备时沉积速率准确度控制在＋6．5％时，基频、二倍频、三倍频和四倍频波长的剩余反射率分别增加至0．24％、0．92％、2．38％和4．37％．当薄膜材料折射率的变化控制在＋3％时，1064nm波长的剩余反射率增大为0．18％，532nm、355nm和266nm波长分别达0．61％，0．59％，0．20％．与薄膜物理厚度相比，膜层折射率对剩余反射率的影响大．对膜系敏感层的分析表明，在1064nm和266nm波长，从入射介质向基底过渡的第二层膜厚度变化对剩余反射率的影响最大，其次是第一膜层．在532nm和355nm波长，从入射介质向基底过渡的第一和第四膜层是该膜系的敏感层．误差分析也表明，薄膜材料的色散对特定波长的剩余反射率具有明显影响，即1064nm、532nm、355nm和266nm波长的剩余反射率分别增加至0．30％、0．23％、0．58％和3．13％．

Investigation on properties of TiO2 thin films deposited at different oxygen pressures

TiO2 thin films were prepared by electron beam evaporation at different oxygen partial pressures. The influences of oxygen partial pressure on optical, mechanical and structural properties of TiO2 thin films were studied. The results showed that with the increase of oxygen partial pressure, the optical transmittance gradually increased, the transmittance edge gradually shifted to short wavelength, and the corresponding refractive index decreased. The residual stresses of all samples were tensile, and the value increased as oxygen partial pressure increasing, which corresponded to the evolutions of the packing densities. The structures of TiO2 thin films all were amorphous because deposition particles did not possess enough energy to crystallize. (C) 2007 Elsevier Ltd. All rights reserved.

SiO_2薄膜折射率的准确拟合分析

精确的光学常数对于设计和制备高品质的光学薄膜非常重要,尤其是那些光学性能对折射率变化敏感的薄膜。SiO_2是一种常用的低折射率材料,因与常用基底折射率相近使其准确拟合有一定难度。实验通过离子束溅射制备了SiO_2单层膜。考虑测量时的误差和基底折射率的影响,采用透射率包络和反射率包络得到了SiO_2的折射率,并用所得折射率进行反演来对这两种途径在实际测量拟合过程中的准确性进行比对。分析表明,剩余反射率在实际的测量过程中误差更小,直接用测量镀膜前后基片的剩余反射率值可以更简便更准确地得到SiO_2的折射率,能达到10~(-2)的精度。

Y2O3 stabilized ZrO2 thin films deposited by electron-beam evaporation: Optical properties, structure and residual stresses

This paper describes the preparation and the characterization Of Y2O3 stabilized ZrO2 thin films produced by electric-beam evaporation method. The optical properties, microstructure, surface morphology and the residual stress of the deposited films were investigated by optical spectroscopy, X-ray diffraction (XRD), scanning probe microscope and optical interferometer. It is shown that the optical transmission spectra of all the YSZ thin films are similar with those of ZrO2 thin film, possessing high transparency in the visible and near-infrared regions. The refractive index of the samples decreases with increasing of Y2O3 content. The crystalline structure of pure ZrO2 films is a mixture of tetragonal phase and monoclinic phase, however, Y2O3 stabilized ZrO2 thin films only exhibit the cubic phase independently of how much the added Y2O3 content is. The surface morphology spectrum indicates that all thin films present a crystalline columnar texture with columnar grains perpendicular to the substrate and with a predominantly open microporosity. The residual stress of films transforms tensile from compressive with the increasing Of Y2O3 molar content, which corresponds to the evolutions of the structure and packing densities. (C) 2008 Elsevier Ltd. All rights reserved.