Is the concept of a green economy a useful way of framing Policy Discussions and policymaking to promote sustainable development?

In the Viewpoints section, academics, practitioners and experts share their perspectives on policy questions relevant to sustainable development. In this issue, experts address the question: “Is the concept of a green economy a useful way of framing policy discussions and policymaking to promote sustainable development?

Concept of project: learning lessons

The concept of Project encompasses a semantic disparity that involves all areas of professional and nonprofessional activity. In the engineering projects domain, and starting by the etymological roots of the terms, a review of the definitions given by different authors and their relation with sociological trends of the last decades is carried out. The engineering projects began as a tool for the development of technological ideas and have been improved with legal, economic and management parameters and recently with environmental aspects. However, the engineering projects involve people, groups, agents, organizations, companies and institutions. Nowadays, the social implications of projects are taken into consideration but the technology for social integration is not consolidated. This communication provides a new framework based on the experience for the development of engineering projects in the context of "human development", placing people in the center of the project

Towards the foundation of a global modes concept

A contribution is presented, intended to provide theoretical foundations for the ongoing efforts to employ global instability theory for the analysis of the classic boundary-layer flow, and address the associated issue of appropriate inflow/outflow boundary conditions to close the PDE-based global eigenvalue problem in open flows. Starting from a theoretically clean and numerically simple application, in which results are also known analytically and thus serve as a guidance for the assessment of the performance of the numerical methods employed herein, a sequence of issues is systematically built into the target application, until we arrive at one representative of open systems whose instability is presently addressed by global linear theory applied to open flows, the latter application being neither tractable theoretically nor straightforward to solve by numerical means. Experience gained along the way is documented. It regards quantification of the depar- ture of the numerical solution from the analytical one in the simple problem, the generation of numerical boundary layers at artificially truncated boundaries, no matter how far the latter are placed from the region of highest flow gradients and, ultimately the impracti- cally large number of (direct and adjoint) modes necessary to project an arbitrary initial perturbation and follow its temporal evolution by a global analysis approach, a finding which may question the purported robustness reported in the literature of the recovery of optimal perturbations as part of global analyses yielding under-resolved eigenspectra.

EU-CargoXpress: wind propulsion concept

The EU-CargoXpress project suggests the usage of sustainable energies to reduce the fuel consumption. The updated concept consists of hoisting the superstructure and using it as a sail together with the conventional propulsion. This paper presents the study of the sail performance by means of a computational analysis and wind tunnel tests. Moreover, a research of the energy saving in different operational areas has been conducted. It is concluded that there is a significant energy saving by using the superstructure as a sail which leads to a reduction of fossil fuel consumption and consequently, a reduction of greenhouse gas emissions.

Applying concept mapping strategies to improve students’ lifelong learning in physical chemistry

Este artículo ofrece una reflexión sobre el papel de los mapas conceptuales en el actual escenario de la educación In the present paper, we carry out the application of concept mapping strategies to learning Physical Chemistry, in particular, of all aspect of Corrosion. This strategy is an alternative method to supplement examinations: it can show the teacher how much the students knew and how much they didn´t know; and the students can evaluate their own learning. Before giving tile matter on Corrosion, the teachers evaluated the previous knowledge of the students in the field and explained to the students how create the conceptual maps with Cmap tools. When the subject is finished, teachers are assessed the conceptual maps developed by students and therefore also the level of the students learning. Teachers verified that the concept mapping is quite suitable for complicated theorics as Corrosion and it is an appropriate tool for the consolidation of educational experiences and for improvement affective lifelong learning. By using this method we demonstrated that the set of concepts accumulated in the cognitive structure of every student in unique and every student has therefore arranged the concepts from top to bottom in the mapping field in different ways with different linking" phrases, although these are involved in the same learning task.

Towards concept identification using a knowledge-intensive approach

This paper presents a method for identifying concepts in microposts and classifying them into a predefined set of categories. The method relies on the DBpedia knowledge base to identify the types of the concepts detected in the messages. For those concepts that are not classified in the ontology we infer their types via the ontology properties which characterise the type.

Proof of concept of an imaging system demonstrator for PET applications with SiPM

A PET imaging system demonstrator based on LYSO crystal arrays coupled to SiPM matrices is under construction at the University and INFN of Pisa. Two SiPM matrices, composed of 8×8 SiPM pixels, and 1,5 mm pitch, have been coupled one to one to a LYSO crystals array and read out by a custom electronics system. front-end ASICs were used to read 8 channels of each matrix. Data from each front-end were multiplexed and sent to a DAQ board for the digital conversion; a motherboard collects the data and communicates with a host computer through a USB port for the storage and off-line data processing. In this paper we show the first preliminary tomographic image of a point-like radioactive source acquired with part of the two detection heads in time coincidence.

Concept of operations for ATM by managing uncertainty through multiple metering points

This paper presents an operational concept for Air Traffic Management, and in particular arrival management, in which aircraft are permitted to operate in a manner consistent with current optimal aircraft operating techniques. The proposed concept allows aircraft to descend in the fuel efficient path managed mode and with arrival time not actively controlled. It will be demonstrated how the associated uncertainty in the time dimension of the trajectory can be managed through the application of multiple metering points strategically chosen along the trajectory. The proposed concept does not make assumptions on aircraft equipage (e.g. time of arrival control), but aims at handling mixed-equipage scenarios that most likely will remain far into the next decade and arguably beyond.

Proposal for the Conceptual Design of Aeronautical Final Assembly Lines Based on the Industrial Digital Mock-Up Concept

The design of a Final Assembly Line (FAL) is carry out in the product industrialization activity. The phase dealing with the definition of conceptual solutions is characterized by depending heavily on the personnel experience and being time-consuming. To enhance such process, it is proposed a development of a knowledge based software application to assist designers in the definition of scenarios and to generate conceptual FAL alternatives. Both the scenario and the generated FAL solution are part of the industrialization digital mock-up (IDMU). A commercial software application used in the aircraft programmes and supporting the IDMU concepts of: Product, Process and Resource; was selected to implement a software prototype. This communication presents the adopted methodological approach and the architecture of the developed application.

Voltage limitation analysis in strain-balanced InAs/GaAsN quantum dot solar cells applied to the intermediate band concept

Several attempts have been carried out to manufacture intermediate band solar cells (IBSC) by means of quantum dot (QD) superlattices. This novel photovoltaic concept allows the collection of a wider range of the sunlight spectrum in order to provide higher cell photocurrent while maintaining the open-circuit voltage (VOC) of the cell. In this work, we analyze InAs/GaAsN QD-IBSCs. In these cells, the dilute nitrogen in the barrier plays an important role for the strain-balance (SB) of the QD layer region that would otherwise create dislocations under the effect of the accumulated strain. The introduction of GaAsN SB layers allows increasing the light absorption in the QD region by multi-stacking more than 100 QD layers. The photo-generated current density (JL) versus VOC was measured under varied concentrated light intensity and temperature. We found that the VOC of the cell at 20 K is limited by the bandgap of the GaAsN barriers, which has important consequences regarding IBSC bandgap engineering that are also discussed in this work.

The ion beam shepherd: A new concept for asteroid deflection

A novel slow push asteroid deflection strategy has been recently proposed in which an Earth threatening asteroid can be deflected by exploiting the momentum transmitted by a collimated beam of quasi-neutral plasma impinging against the asteroid surface. The beam can be generated with state-of-the art ion engines from a hovering spacecraft with no need for physical attachment or gravitational interaction with the celestial body. The spacecraft, placed at a distance of a few asteroid diameters, would need an ion thruster pointed at the asteroid surface as well as a second propulsion system to compensate for the ion engine reaction and keep the distance between the asteroid and the shepherd satellite constant throughout the deflection phase. A comparison in terms of required spacecraft mass per total imparted deflection impulse shows that the method outperforms the gravity tractor concept by more than one order of magnitude for asteroids up to about 200 m diameter. The two methods would yield comparable performance for asteroids larger than about 2 km

Output Impedance Correction Circuit (OICC): A New Concept to Improve the Dynamic Response of DC/DC Converters with Additional Energy Path

El desarrollo da las nuevas tecnologías permite a los ingenieros llevar al límite el funcionamiento de los circuitos integrados (Integrated Circuits, IC). Las nuevas generaciones de procesadores, DSPs o FPGAs son capaces de procesar la información a una alta velocidad, con un alto consumo de energía, o esperar en modo de baja potencia con el mínimo consumo posible. Esta gran variación en el consumo de potencia y el corto tiempo necesario para cambiar de un nivel al otro, afecta a las especificaciones del Módulo de Regulador de Tensión (Voltage Regulated Module, VRM) que alimenta al IC. Además, las características adicionales obligatorias, tales como adaptación del nivel de tensión (Adaptive Voltage Positioning, AVP) y escalado dinámico de la tensión (Dynamic Voltage Scaling, DVS), imponen requisitos opuestas en el diseño de la etapa de potencia del VRM. Para poder soportar las altas variaciones de los escalones de carga, el condensador de filtro de salida del VRM se ha de sobredimensionar, penalizando la densidad de energía y el rendimiento durante la operación de DVS. Por tanto, las actuales tendencias de investigación se centran en mejorar la respuesta dinámica del VRM, mientras se reduce el tamaño del condensador de salida. La reducción del condensador de salida lleva a menor coste y una prolongación de la vida del sistema ya que se podría evitar el uso de condensadores voluminosos, normalmente implementados con condensadores OSCON. Una ventaja adicional es que reduciendo el condensador de salida, el DVS se puede realizar más rápido y con menor estrés de la etapa de potencia, ya que la cantidad de carga necesaria para cambiar la tensión de salida es menor. El comportamiento dinámico del sistema con un control lineal (Control Modo Tensión, VMC, o Control Corriente de Pico, Peak Current Mode Control, PCMC,…) está limitado por la frecuencia de conmutación del convertidor y por el tamaño del filtro de salida. La reducción del condensador de salida se puede lograr incrementando la frecuencia de conmutación, así como incrementando el ancho de banda del sistema, y/o aplicando controles avanzados no-lineales. Usando esos controles, las variables del estado se saturan para conseguir el nuevo régimen permanente en un tiempo mínimo, así como el filtro de salida, más específicamente la pendiente de la corriente de la bobina, define la respuesta de la tensión de salida. Por tanto, reduciendo la inductancia de la bobina de salida, la corriente de bobina llega más rápido al nuevo régimen permanente, por lo que una menor cantidad de carga es tomada del condensador de salida durante el tránsito. El inconveniente de esa propuesta es que el rendimiento del sistema es penalizado debido al incremento de pérdidas de conmutación y las corrientes RMS. Para conseguir tanto la reducción del condensador de salida como el alto rendimiento del sistema, mientras se satisfacen las estrictas especificaciones dinámicas, un convertidor multifase es adoptado como estándar para aplicaciones VRM. Para asegurar el reparto de las corrientes entre fases, el convertidor multifase se suele implementar con control de modo de corriente. Para superar la limitación impuesta por el filtro de salida, la segunda posibilidad para reducir el condensador de salida es aplicar alguna modificación topológica (Topologic modifications) de la etapa básica de potencia para incrementar la pendiente de la corriente de bobina y así reducir la duración de tránsito. Como el transitorio se ha reducido, una menor cantidad de carga es tomada del condensador de salida bajo el mismo escalón de la corriente de salida, con lo cual, el condensador de salida se puede reducir para lograr la misma desviación de la tensión de salida. La tercera posibilidad para reducir el condensador de salida del convertidor es introducir un camino auxiliar de energía (additional energy path, AEP) para compensar el desequilibrio de la carga del condensador de salida reduciendo consecuentemente la duración del transitorio y la desviación de la tensión de salida. De esta manera, durante el régimen permanente, el sistema tiene un alto rendimiento debido a que el convertidor principal con bajo ancho de banda es diseñado para trabajar con una frecuencia de conmutación moderada para conseguir requisitos estáticos. Por otro lado, el comportamiento dinámico durante los transitorios es determinado por el AEP con un alto ancho de banda. El AEP puede ser implementado como un camino resistivo, como regulador lineal (Linear regulator, LR) o como un convertidor conmutado. Las dos primeras implementaciones proveen un mayor ancho de banda, acosta del incremento de pérdidas durante el transitorio. Por otro lado, la implementación del convertidor computado presenta menor ancho de banda, limitado por la frecuencia de conmutación, aunque produce menores pérdidas comparado con las dos anteriores implementaciones. Dependiendo de la aplicación, la implementación y la estrategia de control del sistema, hay una variedad de soluciones propuestas en el Estado del Arte (State-of-the-Art, SoA), teniendo diferentes propiedades donde una solución ofrece más ventajas que las otras, pero también unas desventajas. En general, un sistema con AEP ideal debería tener las siguientes propiedades: 1. El impacto del AEP a las pérdidas del sistema debería ser mínimo. A lo largo de la operación, el AEP genera pérdidas adicionales, con lo cual, en el caso ideal, el AEP debería trabajar por un pequeño intervalo de tiempo, solo durante los tránsitos; la otra opción es tener el AEP constantemente activo pero, por la compensación del rizado de la corriente de bobina, se generan pérdidas innecesarias. 2. El AEP debería ser activado inmediatamente para minimizar la desviación de la tensión de salida. Para conseguir una activación casi instantánea, el sistema puede ser informado por la carga antes del escalón o el sistema puede observar la corriente del condensador de salida, debido a que es la primera variable del estado que actúa a la perturbación de la corriente de salida. De esa manera, el AEP es activado con casi cero error de la tensión de salida, logrando una menor desviación de la tensión de salida. 3. El AEP debería ser desactivado una vez que el nuevo régimen permanente es detectado para evitar los transitorios adicionales de establecimiento. La mayoría de las soluciones de SoA estiman la duración del transitorio, que puede provocar un transitorio adicional si la estimación no se ha hecho correctamente (por ejemplo, si la corriente de bobina del convertidor principal tiene un nivel superior o inferior al necesitado, el regulador lento del convertidor principal tiene que compensar esa diferencia una vez que el AEP es desactivado). Otras soluciones de SoA observan las variables de estado, asegurando que el sistema llegue al nuevo régimen permanente, o pueden ser informadas por la carga. 4. Durante el transitorio, como mínimo un subsistema, o bien el convertidor principal o el AEP, debería operar en el lazo cerrado. Implementando un sistema en el lazo cerrado, preferiblemente el subsistema AEP por su ancho de banda elevado, se incrementa la robustez del sistema a los parásitos. Además, el AEP puede operar con cualquier tipo de corriente de carga. Las soluciones que funcionan en el lazo abierto suelen preformar el control de balance de carga con mínimo tiempo, así reducen la duración del transitorio y tienen un impacto menor a las pérdidas del sistema. Por otro lado, esas soluciones demuestran una alta sensibilidad a las tolerancias y parásitos de los componentes. 5. El AEP debería inyectar la corriente a la salida en una manera controlada, así se reduce el riesgo de unas corrientes elevadas y potencialmente peligrosas y se incrementa la robustez del sistema bajo las perturbaciones de la tensión de entrada. Ese problema suele ser relacionado con los sistemas donde el AEP es implementado como un convertidor auxiliar. El convertidor auxiliar es diseñado para una potencia baja, con lo cual, los dispositivos elegidos son de baja corriente/potencia. Si la corriente no es controlada, bajo un pico de tensión de entrada provocada por otro parte del sistema (por ejemplo, otro convertidor conectado al mismo bus), se puede llegar a un pico en la corriente auxiliar que puede causar la perturbación de tensión de salida e incluso el fallo de los dispositivos del convertidor auxiliar. Sin embargo, cuando la corriente es controlada, usando control del pico de corriente o control con histéresis, la corriente auxiliar tiene el control con prealimentación (feed-forward) de tensión de entrada y la corriente es definida y limitada. Por otro lado, si la solución utiliza el control de balance de carga, el sistema puede actuar de forma deficiente si la tensión de entrada tiene un valor diferente del nominal, provocando que el AEP inyecta/toma más/menos carga que necesitada. 6. Escalabilidad del sistema a convertidores multifase. Como ya ha sido comentado anteriormente, para las aplicaciones VRM por la corriente de carga elevada, el convertidor principal suele ser implementado como multifase para distribuir las perdidas entre las fases y bajar el estrés térmico de los dispositivos. Para asegurar el reparto de las corrientes, normalmente un control de modo corriente es usado. Las soluciones de SoA que usan VMC son limitadas a la implementación con solo una fase. Esta tesis propone un nuevo método de control del flujo de energía por el AEP y el convertidor principal. El concepto propuesto se basa en la inyección controlada de la corriente auxiliar al nodo de salida donde la amplitud de la corriente es n-1 veces mayor que la corriente del condensador de salida con las direcciones apropiadas. De esta manera, el AEP genera un condensador virtual cuya capacidad es n veces mayor que el condensador físico y reduce la impedancia de salida. Como el concepto propuesto reduce la impedancia de salida usando el AEP, el concepto es llamado Output Impedance Correction Circuit (OICC) concept. El concepto se desarrolla para un convertidor tipo reductor síncrono multifase con control modo de corriente CMC (incluyendo e implementación con una fase) y puede operar con la tensión de salida constante o con AVP. Además, el concepto es extendido a un convertidor de una fase con control modo de tensión VMC. Durante la operación, el control de tensión de salida de convertidor principal y control de corriente del subsistema OICC están siempre cerrados, incrementando la robustez a las tolerancias de componentes y a los parásitos del cirquito y permitiendo que el sistema se pueda enfrentar a cualquier tipo de la corriente de carga. Según el método de control propuesto, el sistema se puede encontrar en dos estados: durante el régimen permanente, el sistema se encuentra en el estado Idle y el subsistema OICC esta desactivado. Por otro lado, durante el transitorio, el sistema se encuentra en estado Activo y el subsistema OICC está activado para reducir la impedancia de salida. El cambio entre los estados se hace de forma autónoma: el sistema entra en el estado Activo observando la corriente de condensador de salida y vuelve al estado Idle cunado el nuevo régimen permanente es detectado, observando las variables del estado. La validación del concepto OICC es hecha aplicándolo a un convertidor tipo reductor síncrono con dos fases y de 30W cuyo condensador de salida tiene capacidad de 140μF, mientras el factor de multiplicación n es 15, generando en el estado Activo el condensador virtual de 2.1mF. El subsistema OICC es implementado como un convertidor tipo reductor síncrono con PCMC. Comparando el funcionamiento del convertidor con y sin el OICC, los resultados demuestran que se ha logrado una reducción de la desviación de tensión de salida con factor 12, tanto con funcionamiento básico como con funcionamiento AVP. Además, los resultados son comparados con un prototipo de referencia que tiene la misma etapa de potencia y un condensador de salida físico de 2.1mF. Los resultados demuestran que los dos sistemas tienen el mismo comportamiento dinámico. Más aun, se ha cuantificado el impacto en las pérdidas del sistema operando bajo una corriente de carga pulsante y bajo DVS. Se demuestra que el sistema con OICC mejora el rendimiento del sistema, considerando las pérdidas cuando el sistema trabaja con la carga pulsante y con DVS. Por lo último, el condensador de salida de sistema con OICC es mucho más pequeño que el condensador de salida del convertidor de referencia, con lo cual, por usar el concepto OICC, la densidad de energía se incrementa. En resumen, las contribuciones principales de la tesis son: • El concepto propuesto de Output Impedance Correction Circuit (OICC), • El control a nivel de sistema basado en el método usado para cambiar los estados de operación, • La implementación del subsistema OICC en lazo cerrado conjunto con la implementación del convertidor principal, • La cuantificación de las perdidas dinámicas bajo la carga pulsante y bajo la operación DVS, y • La robustez del sistema bajo la variación del condensador de salida y bajo los escalones de carga consecutiva. ABSTRACT Development of new technologies allows engineers to push the performance of the integrated circuits to its limits. New generations of processors, DSPs or FPGAs are able to process information with high speed and high consumption or to wait in low power mode with minimum possible consumption. This huge variation in power consumption and the short time needed to change from one level to another, affect the specifications of the Voltage Regulated Module (VRM) that supplies the IC. Furthermore, additional mandatory features, such as Adaptive Voltage Positioning (AVP) and Dynamic Voltage Scaling (DVS), impose opposite trends on the design of the VRM power stage. In order to cope with high load-step amplitudes, the output capacitor of the VRM power stage output filter is drastically oversized, penalizing power density and the efficiency during the DVS operation. Therefore, the ongoing research trend is directed to improve the dynamic response of the VRM while reducing the size of the output capacitor. The output capacitor reduction leads to a smaller cost and longer life-time of the system since the big bulk capacitors, usually implemented with OSCON capacitors, may not be needed to achieve the desired dynamic behavior. An additional advantage is that, by reducing the output capacitance, dynamic voltage scaling (DVS) can be performed faster and with smaller stress on the power stage, since the needed amount of charge to change the output voltage is smaller. The dynamic behavior of the system with a linear control (Voltage mode control, VMC, Peak Current Mode Control, PCMC,…) is limited by the converter switching frequency and filter size. The reduction of the output capacitor can be achieved by increasing the switching frequency of the converter, thus increasing the bandwidth of the system, and/or by applying advanced non-linear controls. Applying nonlinear control, the system variables get saturated in order to reach the new steady-state in a minimum time, thus the output filter, more specifically the output inductor current slew-rate, determines the output voltage response. Therefore, by reducing the output inductor value, the inductor current reaches faster the new steady state, so a smaller amount of charge is taken from the output capacitor during the transient. The drawback of this approach is that the system efficiency is penalized due to increased switching losses and RMS currents. In order to achieve both the output capacitor reduction and high system efficiency, while satisfying strict dynamic specifications, a Multiphase converter system is adopted as a standard for VRM applications. In order to ensure the current sharing among the phases, the multiphase converter is usually implemented with current mode control. In order to overcome the limitation imposed by the output filter, the second possibility to reduce the output capacitor is to apply Topologic modifications of the basic power stage topology in order to increase the slew-rate of the inductor current and, therefore, reduce the transient duration. Since the transient is reduced, smaller amount of charge is taken from the output capacitor under the same load current, thus, the output capacitor can be reduced to achieve the same output voltage deviation. The third possibility to reduce the output capacitor of the converter is to introduce an additional energy path (AEP) to compensate the charge unbalance of the output capacitor, consequently reducing the transient time and output voltage deviation. Doing so, during the steady-state operation the system has high efficiency because the main low-bandwidth converter is designed to operate at moderate switching frequency, to meet the static requirements, whereas the dynamic behavior during the transients is determined by the high-bandwidth auxiliary energy path. The auxiliary energy path can be implemented as a resistive path, as a Linear regulator, LR, or as a switching converter. The first two implementations provide higher bandwidth, at the expense of increasing losses during the transient. On the other hand, the switching converter implementation presents lower bandwidth, limited by the auxiliary converter switching frequency, though it produces smaller losses compared to the two previous implementations. Depending on the application, the implementation and the control strategy of the system, there is a variety of proposed solutions in the State-of-the-Art (SoA), having different features where one solution offers some advantages over the others, but also some disadvantages. In general, an ideal additional energy path system should have the following features: 1. The impact on the system losses should be minimal. During its operation, the AEP generates additional losses, thus ideally, the AEP should operate for a short period of time, only when the transient is occurring; the other option is to have the AEP constantly on, but due to the inductor current ripple compensation at the output, unnecessary losses are generated. 2. The AEP should be activated nearly instantaneously to prevent bigger output voltage deviation. To achieve near instantaneous activation, the converter system can be informed by the load prior to the load-step or the system can observe the output capacitor current, which is the first system state variable that reacts on the load current perturbation. In this manner, the AEP is turned on with near zero output voltage error, providing smaller output voltage deviation. 3. The AEP should be deactivated once the new steady state is reached to avoid additional settling transients. Most of the SoA solutions estimate duration of the transient which may cause additional transient if the estimation is not performed correctly (e.g. if the main converter inductor current has higher or lower value than needed, the slow regulator of the main converter needs to compensate the difference after the AEP is deactivated). Other SoA solutions are observing state variables, ensuring that the system reaches the new steady state or they are informed by the load. 4. During the transient, at least one subsystem, either the main converter or the AEP, should be in closed-loop. Implementing a closed loop system, preferably the AEP subsystem, due its higher bandwidth, increases the robustness under system tolerances and circuit parasitic. In addition, the AEP can operate with any type of load. The solutions that operate in open loop usually perform minimum time charge balance control, thus reducing the transient length and minimizing the impact on the losses, however they are very sensitive to tolerances and parasitics. 5. The AEP should inject current at the output in a controlled manner, thus reducing the risk of high and potentially damaging currents and increasing robustness on the input voltage deviation. This issue is mainly related to the systems where AEP is implemented as auxiliary converter. The auxiliary converter is designed for small power and, as such, the MOSFETs are rated for small power/currents. If the current is not controlled, due to the some unpredicted spike in input voltage caused by some other part of the system (e.g. different converter), it may lead to a current spike in auxiliary current which will cause the perturbation of the output voltage and even failure of the switching components of auxiliary converter. In the case when the current is controlled, using peak CMC or Hysteretic Window CMC, the auxiliary converter has inherent feed-forwarding of the input voltage in current control and the current is defined and limited. Furthermore, if the solution employs charge balance control, the system may perform poorly if the input voltage has different value than the nominal, causing that AEP injects/extracts more/less charge than needed. 6. Scalability of the system to multiphase converters. As commented previously, in VRM applications, due to the high load currents, the main converters are implemented as multiphase to redistribute losses among the modules, lowering temperature stress of the components. To ensure the current sharing, usually a Current Mode Control (CMC) is employed. The SoA solutions that are implemented with VMC are limited to a single stage implementation. This thesis proposes a novel control method of the energy flow through the AEP and the main converter system. The proposed concept relays on a controlled injection of the auxiliary current at the output node where the instantaneous current value is n-1 times bigger than the output capacitor current with appropriate directions. Doing so, the AEP creates an equivalent n times bigger virtual capacitor at the output, thus reducing the output impedance. Due to the fact that the proposed concept reduces the output impedance using the AEP, it has been named the Output Impedance Correction Circuit (OICC) concept. The concept is developed for a multiphase CMC synchronous buck converter (including a single phase implementation), operating with a constant output voltage and with AVP feature. Further, it is extended to a single phase VMC synchronous buck converter. During the operation, the main converter voltage loop and the OICC subsystem capacitor current loop is constantly closed, increasing the robustness under system tolerances and circuit parasitic and allowing the system to operate with any load-current shape or pattern. According to the proposed control method, the system operates in two states: during the steady-state the system is in the Idle state and the OICC subsystem is deactivated, while during the load-step transient the system is in the Active state and the OICC subsystem is activated in order to reduce the output impedance. The state changes are performed autonomously: the system enters in the Active state by observing the output capacitor current and it returns back to the Idle state when the steady-state operation is detected by observing the state variables. The validation of the OICC concept has been done by applying it to a 30W two phase synchronous buck converter with 140μF output capacitor and with the multiplication factor n equal to 15, generating during the Active state equivalent output capacitor of 2.1mF. The OICC subsystem is implemented as single phase PCMC synchronous buck converter. Comparing the converter operation with and without the OICC the results demonstrate that the 12 times reduction of the output voltage deviation is achieved, for both basic operation and for the AVP operation. Furthermore, the results have been compared to a reference prototype which has the same power stage and a fiscal output capacitor of 2.1mF. The results show that the two systems have the same dynamic behavior. Moreover, an impact on the system losses under the pulsating load and DVS operation has been quantified and it has been demonstrated that the OICC system has improved the system efficiency, considering the losses when the system operates with the pulsating load and the DVS operation. Lastly, the output capacitor of the OICC system is much smaller than the reference design output capacitor, therefore, by applying the OICC concept the power density can be increased. In summary, the main contributions of the thesis are: • The proposed Output Impedance Correction Circuit (OICC) concept, • The system level control based on the used approach to change the states of operation, • The OICC subsystem closed-loop implementation, together with the main converter implementation, • The dynamic losses under the pulsating load and the DVS operation quantification, and • The system robustness on the capacitor impedance variation and consecutive load-steps.

Nonlinear normal modes in mechanical systems: concept and computation with numerical continuation

The purpose of this Project is, first and foremost, to disclose the topic of nonlinear vibrations and oscillations in mechanical systems and, namely, nonlinear normal modes NNMs to a greater audience of researchers and technicians. To do so, first of all, the dynamical behavior and properties of nonlinear mechanical systems is outlined from the analysis of a pair of exemplary models with the harmonic balanced method. The conclusions drawn are contrasted with the Linear Vibration Theory. Then, it is argued how the nonlinear normal modes could, in spite of their limitations, predict the frequency response of a mechanical system. After discussing those introductory concepts, I present a Matlab package called 'NNMcont' developed by a group of researchers from the University of Liege. This package allows the analysis of nonlinear normal modes of vibration in a range of mechanical systems as extensions of the linear modes. This package relies on numerical methods and a 'continuation algorithm' for the computation of the nonlinear normal modes of a conservative mechanical system. In order to prove its functionality, a two degrees of freedom mechanical system with elastic nonlinearities is analized. This model comprises a mass suspended on a foundation by means of a spring-viscous damper mechanism -analogous to a very simplified model of most suspended structures and machines- that has attached a mass damper as a passive vibration control system. The results of the computation are displayed on frequency energy plots showing the NNMs branches along with modal curves and time-series plots for each normal mode. Finally, a critical analysis of the results obtained is carried out with an eye on devising what they can tell the researcher about the dynamical properties of the system.

Artefactos energéticos : de Fuller a Piñero (1961-1972) = Energetic artefacts : from Fuller to Piñero (1961-1972)

La obra de Emilio Pérez Piñero que se desarrolla entre los años 1961 y 1972 año en el que muere en un accidente de tráfico volviendo de Figueras, se centra principalmente en artefactos desplegables y desmontables, ejecutando prototipos que en el presente trabajo se han dividido en dos grupos; la cúpula reticular y la infraestructura. No pudo por tanto acudir al Congreso de 1972 de la UIA a recoger el premio Auguste Perret a la innovación tecnológica, que en años anteriores habían recibido Félix Candela, Jean Prouvé, Hans Scharoun o Frei Otto, y que en aquella ocasión tuvo que recoger su viuda. Parámetros como el de la movilidad, indeterminación, intercambiabilidad, obsolescencia y otros que se analizan en el presente trabajo, aparecen a lo largo de toda su obra ya que muchos de sus artefactos están ubicados en no-lugares y tienen un carácter itinerante y por tanto se hace indispensable su rápido montaje y desmontaje, que unas veces se resuelve mediante la desmontabilidad y otras con la plegabilidad de éstos. Aunque pueda parecer Piñero una figura autárquica, lo cierto es que durante la década donde concentra su trabajo se produce una explosión en torno a al arquetipo que será denominado de forma genérica `artefacto´, ligado conceptualmente a los parámetros que aquí se definen. Entendemos artefacto como objeto material realizado por una o varias personas para cumplir una función, es sinónimo de máquina y aparato y deriva de las palabras latinas ars o artis (técnica) y facto (hecho), para designar a los objetos cuya fabricación requiere alguna destreza. El término latino `ars´ engloba a las técnicas y a las artes, lo que no ocurre con el término castellano arte que deriva de él. Los movimientos utópicos que comparte la década con Piñero, utilizan el arquetipo infraestructural, ligero y high tech, para a través de una arquitectura más ligada a la ciencia ficción, realizar una crítica al Movimiento Moderno institucionalizado, todos ellos comparten cierta obsesión por la movilidad, ligada ésta a la idea de espacio flexible, dinámico, nómada. Este concepto de neo-nomadismo, que representa un habitar dinámico, aglutina las nuevas formas de vivir donde la movilidad social y geográfica son habituales. El nomadismo, por otra parte se entiende como sinónimo de democracia y libertad. La arquitectura pasa de ser pesada, estática, permanente a ser un elemento dinámico en continuo movimiento. A veces con connotaciones biológicas se asimilan los artefactos a organismos vivos y les confieren dichas propiedades de crecimiento y autonomía energética, acumulándose en torno a megaestructuras, donde quedan `enchufados´. En este intento de dotar movilidad a lo inmueble, se buscan estructuras vivas y modificables que crecen en una asimilación de las leyes naturales utilizando los parámetros de metamorfosis, simbiosis y cambio. Estos movimientos de vanguardia tienen también ciertas connotaciones políticas y sociales basadas en la libertad y la movilidad y reniegan del consumismo institucionalizado, de la arquitectura como instrumento de consumo, como objeto de usar en la cultura de masas. El carácter político de la autogestión, de la customización como parámetro proyectual, de la autosuficiencia energética, que anticipa la llegada de la crisis energética del año 1973. Objeto de este trabajo será relacionar los conceptos que aparecen fuertemente en el entorno de la década de los años sesenta del siglo XX, en el trabajo de Emilio Pérez Piñero. Parámetros encontrados como conceptos en los grupos de vanguardia y utopía a su vez fuertemente influenciados por las figuras del ingeniero Richard Buckminster Fuller y del arquitecto Konrad Wachsmann. Se analizará que posible influencia tiene la obra de Fuller, principalmente el prototipo denominado cúpula reticular, en la obra de Pérez Piñero y sus coetáneos analizando sus pensamientos teóricos en torno a parámetros como la energía, principalmente en las teorías relativas a Synergetics. El término inventado por Richard B. Fuller es una contracción de otro más largo que en inglés agrupa tres palabras; synergetic-energetic geometry. La definición de sinergia es la cooperación, es decir es el resultado de la acción conjunta de dos o más causas, pero con un efecto superior a la suma de estas causas. El segundo término, energetics geometry, que traducido sería geometría energética hace referencia en primer lugar a la geometría; ya que desarrolla el sistema de referencia que utiliza la naturaleza para construir sus sistemas y en segundo lugar a la energía; ya que además debe ser el sistema que establezca las relaciones más económicas utilizando el mínimo de energía. Por otro lado se analiza la repercusión del prototipo denominado Infraestructura, término acuñado por Yona Friedman y basado estructuralmente y conceptualmente en los desarrollos sobre grandes estructuras de Konrad Wachsmann. El arquitecto alemán divulga su conocimiento en seminarios impartidos por todo el mundo como el que imparte en Tokio y se denomina Wachsmann´s Seminar donde participan algunos de los componentes del grupo Metabolista que sorprenderán al mundo con sus realizaciones en la exposición de Osaka de 1970. El intervalo temporal entre 1961 hasta 1972 hace referencia a la horquilla donde Pérez Piñero realiza su obra arquitectónica, que comienza en 1961 cuando gana el concurso convocado en Londres por la UIA (Unión Internacional de Arquitectos) con el proyecto conocido como Teatro Ambulante, hasta 1972 que es cuando fallece volviendo de Figueras donde está realizando dos encargos de Salvador Dalí; la cubrición del escenario del futuro Teatro-Museo Salvador Dalí y la Vidriera Hipercúbica que debía cerrar la boca de tal escenario. Bajo el título de `Artefactos energéticos. De Fuller a Piñero (1961-1972)´, se presenta esta Tesis doctoral, que tiene la intención de vincular la obra de Emilio Pérez Piñero con la de las neo vanguardias producidas por una serie de arquitectos que operan en el ámbito internacional. Estas vinculaciones se producen de una forma general, donde a través de una serie de estrategias según la metodología que posteriormente se describe se buscan relaciones de la obra del autor español con algunos de los movimientos más significativos que aparecen en dicha década y de manera específica estableciendo relaciones con las obras y pensamientos de los autores que pertenecen a estos movimientos y donde estas relaciones se hacen más evidentes. El objeto del presente trabajo es analizar y explicar la obra del arquitecto Emilio Pérez Piñero, que espacialmente se localiza en el territorio español, desde el punto de vista de estos movimientos para posteriormente poder determinar si existen puntos en común y si el arquitecto español no solo comparte la década temporalmente sino también conceptualmente y por tanto utiliza el ideario que utilizan sus coetáneos que forman parte de las neovanguardias de los años sesenta de siglo XX. ABSTRACT ABSTRACT The Work of Emilio Perez Piñero was developed between the years 1961 and 1972 when he died in a car accident coming back from Figueres, where he was building a geodesic dome to close the building that enclose the Dali’s museum. All his Work is mainly centered in artifact that could be collapsible and removable, taking the two prototypes that are described in this work as a recurrent element in all his creation. These are the reticular dome and the infrastructure that are very influenced by the work from Richard B. Fuller and Konrad Wachsmann. Emilio Pérez Piñero could not receive the Auguste Perret Prize in 1972 awarded by the UIA that years before have received architects as Felix Candela, Jean Prouvé, Hans Scharoun or Frei Otto, and this time Pérez Piñero´s wife will accept it because of his death. Parameters like mobility, changeability, expendability, indetermination and others appear currently in his Work. All the inventions that Piñero had been patented and all of the artifacts that he created are usually located in no-places, because they do have a shifting identity. This kind of building has to be quickly set on site, and this problem has to be solved in term of foldability or demounting. In the decade where his work focuses, an explosion has occurred around this archetype to be generally called artifact that is usually linked to mobility. We understand artifact as a material object made by one or more people to work in a particular way. It is sometimes equated with the terms machinery and apparatus and it is derived from the Latin word `ars´ or `artis´, what means techniques and `facto´ (fact). And we use this term to refer to objects whose manufacture requires the same skill, in fact the Latin word `ars´ covers the techniques and arts, which does not occur with the Castillan term `arte´ that derives from it and means only art. The term neo-nomadic is a relatively new name used for a dynamic life, commonly referred to new forms of life where social and geographical mobility are common. On the other hand nomadic could be understood as a synonymous for democracy and freedom. The architecture is not going to be hard and static anymore but a dynamic element in the move. The Neo-avant-garde movement that shares the decade with Piñero uses this infrastructural archetype, which is light and high-tech, to criticize the institutionalized Modern Movement through architecture linked to science fiction. They all share an obsession with mobility, a concept that is connected to the terms `dynamic´, `nomadic´, `flexibile´, etc. Sometimes, with biological connotations, the utopian assimilate the artifacts to living organisms and give them these properties of growth and energy autonomy, and they apparently grow around megastructures where they are plugged. In this attempt to provide mobility to the inertness, living structures and possibility of change are sought in order to make them grow like a living organism and to assimilate the natural laws of growth. According to a definition from architecture provided by Fernández- Galiano who calls it `exosomatic artifact´, he understand architecture as artifact of the human environment that regulates natural energy flows and channels the energy stored in fuels for the benefit of living beings that inhabit. It is also true that during the sixties a new environmental awareness in public opinion is formed and that is due to the exploitation and disproportionate use of energy resources, acceleration of technological processes and mass consumption. Consequently a new concept is born: energy autonomy, it is very close to rational use of natural energy. Such a concept will be culturally assimilated with the requirement of independence not only in the management but also in the building construction until we arrive at energy autonomy. The individuals become energy consumer, which in turn can enter the energy produced in the system to `life in an eco-mode way´. The objectives of this research are analyzing all of these parameters and concepts that are coming into view in the surrounding of the decade and relate them with the Work of Pérez Piñero. Terms strongly present in the avant-garde movements around the decade, a young architect’s generation strongly influenced by Richard B. Fuller and Konrad Wachsmann. However, it will be analyzed how important the influence of Buckminster Fuller's Work was and his theoretical text about energy on the Work of Pérez Piñero and his fellows of the decade. The term Synergetic was invented by Fuller and came from the words synergy and energetic geometry. Synergy is the cooperation or interaction of two or more agents to produce a greater effect than the sum of their separate effects. Energetic geometry is related to the geometries that the Nature is using to build their construction but always using low energy consumption. On the other hand, the influences from Wachsmann around the prototype called Infrastructure have been analyzed. The German architect has developed knowledge around huge structures that he has spread all around the world through seminars that he has been conducted. One of these was the Wachsmann´s seminar in Tokyo, where same of the members of the Metabolist group were taking part of. Later these young architects will surprise the world with his artifacts at the World Exposition in Osaka in 1970. Between 1961 and 1972 Pérez Piñero produced his architectural work. It began in 1961 when he received the first prize with his project Mobile Theatre in the competition organized by the UIA in London. In 1972 the Auguste Perret Prize was granted by the UIA too. He could not accept it because he died before in a car accident when he was coming from Figueres, when he was designing two projects for Dali. With the title `Energetic Artifacts. From Fuller to Piñero (1961- 1972)´, this thesis relates the Work of Emilio Pérez Piñero with the neo avant-garde made by a young architects’ generation who is sharing the time with him. Several strategies have been used to formed relationships between them. They are described in the present work to set up a method that allows us to relate the work and ideas of the architects of the neo avant-garde with the ones from Piñero. This work is intended to analyze and explained the work of Pérez Piñero from the point of view of the international architects’ generation who is operating at the same time and finally to determinate if Piñero is not sharing the time with them but the concepts, ideas and architectural parameters.

Fluid-solid interaction in arteries incorporating the autoregulation concept in boundary conditions

In pre-surgery decisions in hospital emergency cases, fast and reliable results of the solid and fluid mechanics problems are of great interest to clinicians. In the current investigation, an iterative process based on a pressure-type boundary condition is proposed in order to reduce the computational costs of blood flow simulations in arteries, without losing control of the important clinical parameters. The incorporation of cardiovascular autoregulation, together with the well-known impedance boundary condition, forms the basis of the proposed methodology. With autoregulation, the instabilities associated with conventional pressure-type or impedance boundary conditions are avoided without an excessive increase in computational costs. The general behaviour of pulsatile blood flow in arteries, which is important from the clinical point of view, is well reproduced through this new methodology. In addition, the interaction between the blood and the arterial walls occurs via a modified weak coupling, which makes the simulation more stable and computationally efficient. Based on in vitro experiments, the hyperelastic behaviour of the wall is characterised and modelled. The applications and benefits of the proposed pressure-type boundary condition are shown in a model of an idealised aortic arch with and without an ascending aorta dissection, which is a common cardiovascular disorder.