Challenges in packaging waste management: A case study in the fast food industry

The main research problem of this thesis is to find out the means of promoting the recovery of packaging waste generated in thefast food industry. The recovery of packaging waste generated in the fast food industry is demanded by the packaging waste legislation and expected by the public. The means are revealed by the general factors influencing the recovery of packaging waste, analysed by a multidisciplinary literature review and a case study focusing on the packaging waste managementof McDonald's Oy operating in Finland. The existing solid waste infrastructure does not promote the recovery ofpackaging waste generated in the fast food industry. The theoretical recovery rate of the packaging waste is high, 93 %, while the actual recovery rate is only 29 % consisting of secondary packaging manufactured from cardboard. The total recovery potential of packaging waste is 64 %, resulting in 1 230 tonnes ofrecoverable packaging waste. The achievable recovery potential of 33 %, equalling 647 tonnes of packaging waste could be recovered, but is not recovered mainly because of non-working waste management practises. The theoretical recovery potential of 31 %, equalling 583 tonnes of packaging waste can not be recovered by the existing solid waste infrastructure because of the obscure status of commecial waste, the improper operation ofproducer organisations, and the municipal autonomy. The sorting experiment indicated that it is possible to reach the achievable recovery potential inthe existing solid waste infrastructure. The achievement is promoted by waste producer -oriented waste management practises. The theoretical recovery potential can be reached by increasing the consistency of the solid waste infrastructure through governmental action.

Influence of secondary packing on the freezing time of chiken meat in air blast freezing tunnels

Freezing of poultry cuts in continuous convective air blast tunnels is normally performed with the products protected by Low Density Polyethylene (LDPE) as a primary packaging and using Corrugated Cardboard Boxes (CCB) as secondary packaging. The objective of this work was to investigate the influence of these secondary packaging on the freezing of poultry cuts in continuous convective air blast tunnels. The study was performed by replacing CCB with Perforated Metal Boxes (PMB) in order to remove the packaging thermal resistance. The assays, performed in a industrial plant, demonstrated that CCB used commercially for meat freezing have a high heat transfer resistance. Their replacement with PMB can lead to shorter freezing times and spatially homogeneous freezing. Reductions of up to 45% in the freezing times were observed using PMB. The plateau of the temperature curve, related to the freezing time of free water, was significantly reduced using PMB, which is accepted to lead to better product quality after thawing. As the products were protected by the LDPE films as primary packaging, their appearance were not affected. The results presented in this work indicate that replacing CBB with PMB can be an excellent alternative to reduce freezing time and improve freezing homogeneity in industrial air blast tunnels, which could also be applied to other products.

Current and future trens in the quality control of pharmaceuticals and biopharmaticals : impacts on Cost of Goods Sold (COGS)

[Summary] 2. Roles of quality control in the pharmaceutical and biopharmaceutical industries. - 2.1. Pharmaceutical industry. - 2.2. Biopharmaceutical industry. - 2.3. Policy and regulatory. - 2.3.1. The US Food and Drug Administration (FDA). - 2.3.2. The European Medicine Agency (EMEA). - 2.3.3. The Japanese Ministry of Work, Labor and Welfare (MHLW). - 2.3.4. The Swiss Agency for Therapeutic Products (Swissmedic). - 2.3.5. The International Conference on Harmonization (ICH). - - 3. Types of testing. - 3.1. Microbiological purity tests. - 3.2. Physiochemical tests. - 3.3. Critical to quality steps. - 3.3.1. API starting materials and excipients. - 3.3.2. Intermediates. - 3.3.3. APIs (drug substances) and final drug product. - 3.3.4. Primary and secondary packaging materials fro drug products. - - 4. Manufacturing cost and quality control. - 4.1.1. Pharmaceutical manufacturing cost breakdown. - 4.1.2. Biopharmaceutical manufacturing cost breakdown. - 4.2. Batch failure / rejection / rework / recalls. - - 5. Future trends in the quality control of pharmaceuticals and biopharmaceuticals. - 5.1. Rapid and real time testing. - 5.1.1. Physio-chemicals testing. - 5.1.2. Rapid microbiology methods

Embalagens de medicamentos: diretrizes para o desenvolvimento

Pós-graduação em Design - FAAC

Translation of the flavivirus Kunjin NS3 gene in cis but not its RNA sequence or secondary structure is essential for efficient RNA packaging

Our previous studies using trans-complementation analysis of Kunjin virus (KUN) full-length cDNA clones harboring in-frame deletions in the NS3 gene demonstrated the inability of these defective complemented RNAs to be packaged into virus particles (W. J. Liu, P. L. Sedlak, N. Kondratieva, and A. A. Khromykh, J. Virol. 76:10766-10775). In this study we aimed to establish whether this requirement for NS3 in RNA packaging is determined by the secondary RNA structure of the NS3 gene or by the essential role of the translated NS3 gene product. Multiple silent mutations of three computer-predicted stable RNA structures in the NS3 coding region of KUN replicon RNA aimed at disrupting RNA secondary structure without affecting amino acid sequence did not affect RNA replication and packaging into virus-like particles in the packaging cell line, thus demonstrating that the predicted conserved RNA structures in the NS3 gene do not play a role in RNA replication and/or packaging. In contrast, double frameshift mutations in the NS3 coding region of full-length KUN RNA, producing scrambled NS3 protein but retaining secondary RNA structure, resulted in the loss of ability of these defective RNAs to be packaged into virus particles in complementation experiments in KUN replicon-expressing cells. Furthermore, the more robust complementation-packaging system based on established stable cell lines producing large amounts of complemented replicating NS3-deficient replicon RNAs and infection with KUN virus to provide structural proteins also failed to detect any secreted virus-like particles containing packaged NS3-deficient replicon RNAs. These results have now firmly established the requirement of KUN NS3 protein translated in cis for genome packaging into virus particles.

Liquid Packaging Board Market in China

Tämän diplomityön tavoitteena on määrittää liiketoimintailmapiiri ja markkinapotentiaali Kiinan nestepakkauskartonkimarkkinoilla. Tutkimus tukee nestepakkauskartonkivalmistajan vientitoimintoja. Pääosin käytännön tiedoista koostuva tutkimus suoritettiin keräämällä sekundaääritietoa ja haastattelemalla alan erikoisasiantuntijoita. Suuri ja kasvava väestö sekä nopeasti kehittyvä talous tukee nestepakkauskartonkimarkkinoiden kasvua Kiinassa. Viimeaikainen globalisaatio haittapuolineen saattaa kuitenkin horjuttaa poliittista ja sosiaalista tasapainoa ja tätä kautta ylellisyys hyödykkeiden kuten kartonkipakattujen tuotteiden kysyntää Kiinassa. Tuontirajoitukset Kiinaan ovat laskemassa valtion tämän hetkisen kansainvälistymispolitiikan seurauksena. Kartonki vahvistaa asemaansa kilpailevien pakkausmateriaalien joukossa. Kiinan kokonaisnestepakkauskartonkimarkkinat kasvavat vuosittain 10,7 % ja ovat vuonna 2001 noin 100 000 tonnia.

Pakkaus- ja graafisten kartonkien markkinakartoitus Suomessa. Case: Stora Enso Oyj:n Packaging Boards -tulosyksikön Imatran tehtaiden Kotimaanmyynti

Tutkielman aiheena on kartoittaa pakkaus- ja graafisten kartonkien markkinoita Suo-messa. Tutkimuksen teoriaosassa esitetään kilpailija-analyysi, asiakasanalyysi ja substituutit, joiden avulla yrityksen asemaa markkinoilla voidaan arvioida. Tutkimuksen empiirisessä osassa luotua teoriaa on sovellettu case-yrityksen markkinoiden kartoittamiseen. Tutkimusta varten on kerätty primääritietoa markkinatutkimuksen avulla, sekä hyödynnetty jo olemassa olevaa sekundääritietoa. Saatua materiaalia on arvioitu kvalitatiivisesti. Tutkimuksen tulokseksi saatiin kartoitus Suomen pakkaus- ja graafisten kartonkien markkinarakenteesta, kilpailijoista, asiakkaista ja substituuteista yleisellä tasolla. Samoin saatiin tulokseksi Stora Enso Packaging Boards -tulosyksikön Imatran tehtaiden Kotimaanmyynnin nykyisten ja potentiaalisten asiakkaiden ostokäyttäytymiseen vaikuttavia tekijöitä, sekä asiakkaiden mielipiteitä Kotimaanmyynnin tuotteista ja toiminnasta.

Image and value of product brand in industrial markets: Case Stora Enso Consumer Packaging Boards

TUTKIMUKSEN TAVOITTEET Tutkielman tavoitteena oli luoda ensin yleiskäsitys tuotemerkkimarkkinoinnin roolista teollisilla markkinoilla, sekä suhdemarkkinoinnin merkityksestä teollisessa merkkituotemarkkinoinnissa. Toisena oleellisena tavoitteena oli kuvata teoreettisesti merkkituoteidentiteetin rakenne teollisessa yrityksessä ja sen vaikutukset myyntihenkilöstöön, ja lisäksi haluttiin tutkia tuotemerkkien lisäarvoa sekä asiakkaalle että myyjälle. Identiteetti ja sen vaikutukset, erityisesti imago haluttiin tutkia myös empiirisesti. LÄHDEAINEISTO JA TUTKIMUSMENETELMÄT Tämän tutkielman teoreettinen osuus perustuu kirjallisuuteen, akateemisiin julkaisuihin ja aikaisempiin tutkimuksiin; keskittyen merkkituotteiden markkinointiin, identiteettiin ja imagoon, sekä suhdemarkkinointiin osana merkkituotemarkkinointia. Tutkimuksen lähestymistapa on kuvaileva eli deskriptiivinen ja sekä kvalitatiivinen että kvantitatiivinen. Tutkimus on tapaustutkimus, jossa caseyritykseksi valittiin kansainvälinen pakkauskartonki-teollisuuden yritys. Empiirisen osuuden toteuttamiseen käytettiin www-pohjaista surveytä, jonka avulla tietoja kerättiin myyntihenkilöstöltä case-yrityksessä. Lisäksi empiiristä osuutta laajennettiin tutkimalla sekundäärilähteitä kuten yrityksen sisäisiä kirjallisia dokumentteja ja tutkimuksia. TULOKSET. Teoreettisen ja empiirisen tutkimuksen tuloksena luotiin malli jota voidaan hyödyntää merkkituotemarkkinoinnin päätöksenteon tukena pakkauskartonki-teollisuudessa. Teollisen brandinhallinnan tulee keskittyä erityisesti asiakas-suhteiden brandaukseen – tätä voisi kutsua teolliseksi suhdebrandaukseksi. Tuote-elementit ja –arvot, differointi ja positiointi, sisäinen yrityskuva ja viestintä ovat teollisen brandi-identiteetin peruskiviä, jotka luovat brandi-imagon. Case-yrityksen myyntihenkilöstön tuote- ja yritysmielikuvat osoittautuivat kokonaisuudessaan hyviksi. Paras imago on CKB tuotteilla, kun taas heikoin on WLC tuotteilla. Teolliset brandit voivat luoda monenlaisia lisäarvoja sekä asiakas- että myyjäyritykselle.

Deinking flotation of recycled linerboard for food packaging applications

Brown packaging linerboard, made entirely from recovered pulp, was subjected to deinking flotation for evaluating the possible improvements in its chemical, optical and mechanical properties. The increase in the rate of recovered paper utilisation, along with the tendency towards lower basis weights, in the packaging paper production, has created a growing need for the utilisation of secondary fibers of improved quality. To attain better quality fibers, flotation deinking of brown grades is being considered, along with the addition of primary fibers to recovered paper furnish. Numerous conducted studies, in which the flotation technology was used in the treatment of brown grades, support this idea. Most of them show that the quality of fibers is improved after flotation deinking, resulting in higher mechanical properties of the deinked handsheets and in lower amounts of chemical contaminants. As to food and human health safety, packaging paper has to meet specific requirements, to be classified as suitable for its direct contact with foods. Recycled paper and board may contain many potential contaminants, which, especially in the case of direct food contact, may migrate from packaging materials into foodstuffs. In this work, the linerboard sample selected for deinking was made from recycled fibers not submitted previously to chemical deinking flotation. Therefore, the original sample contained many noncellulosic components, as well as the residues of printing inks. The studied linerboardsample was a type of packaging paper used for contact with food products that are usually peeled before use, e.g. fruits and vegetables. The decrease in the amount of chemical contaminants, after conducting deinking flotation, was evaluated, along with the changes in the mechanical and optical properties of the deinked handsheets. Food contact analysis was done on both the original paper samples and the filter pads and handsheets made before and after deinking flotation. Food contact analysis consisted of migration tests of brightening agents, colorants, PCPs, formaldehydes and metals. Microbiological tests were also performed to determine the possible transfer of antimicrobial constituents

Effects of internationalization on packaging decisions of manufacturing companies

The world has witnessed a great deal of globalization and a rise in international activities in recent years compared to decades ago. This has contributed to an upsurge in competition among manufacturing firms resulting in the use of different marketing strategies to survive. Packaging is one of the tools that has been used by marketers to make products different and appealing to both local and international customers. The purpose of this research work was to investigate more on packaging as a marketing tool and how internationalization affects the decisions management makes in relation to it. To this effect, a qualitative research was conducted using five manufacturing companies as case studies and data collected through semi-structured interviews and also personal observation. Secondary sources were also used in order to get deeper insight into the case companies under study. The study revealed that there are many advantages that internationalization provides firms. The general revelations made by the firms that were researched did not point to a negative impact of internationalization on their packaging decisions. Internationalization has provided positive improvements on their packaging and made them more competitive. This proves that for packaging decisions to improve better, one key enabler will be exposure to the international environment since it provides a wider array of options for package improvements for firms.

The role of product features on buyer-supplier collaboration in packaging industry

The thesis presents the study relative to the collaboration between suppliers and buyers in packaging industry with the impact of product features. The main purpose of this study is to examine the importance of product characteristics on collaboration to develop better packaging and to figure out how buyer-supplier collaboration in the supply chain perspectives is conducted and managed in packaging industry. The theoretical part reviewed some basic frameworks of collaboration including the scopes and levels of collaboration, risks as well as powers of collaboration, relationship and some key factors for successful collaboration. Followed by the overviews of packaging industry with the main issues related to product characteristics in packaging. By using the qualitative method, secondary data consisting of articles, reports, websites and primary data through interviewing some well-known packaging companies and case companies are collected in the thesis. The empirical result emphasized the importance of product features’ analysis in packaging industry since it plays a central role in the materials, design process, production and innovation with the role of collaboration. Collaboration in packaging is vital for packaging companies to survive and grow in the competitive environment. Finally, some key factors for effective collaboration were summarized based on the perspectives of packaging companies. It is highly recommend building a long-run collaboration with their customers due to undeniable benefits With increasingly importance of collaboration in packaging industry, further studies may be conducted.

Multi-Scale Dynamic Study of Secondary Impact During Drop Testing of Surface Mount Packages

This dissertation focuses on design challenges caused by secondary impacts to printed wiring assemblies (PWAs) within hand-held electronics due to accidental drop or impact loading. The continuing increase of functionality, miniaturization and affordability has resulted in a decrease in the size and weight of handheld electronic products. As a result, PWAs have become thinner and the clearances between surrounding structures have decreased. The resulting increase in flexibility of the PWAs in combination with the reduced clearances requires new design rules to minimize and survive possible internal collisions impacts between PWAs and surrounding structures. Such collisions are being termed ‘secondary impact’ in this study. The effect of secondary impact on board-level drop reliability of printed wiring boards (PWBs) assembled with MEMS microphone components, is investigated using a combination of testing, response and stress analysis, and damage modeling. The response analysis is conducted using a combination of numerical finite element modeling and simplified analytic models for additional parametric sensitivity studies.

System innovation and life cycle thinking in packaging value chain: the circularity of plastics.

Compared to other, plastic materials have registered a strong acceleration in production and consumption during the last years. Despite the existence of waste management systems, plastic_based materials are still a pervasive presence in the environment, with negative consequences on marine ecosystem and human health. The recycling is still challenging due to the growing complexity of product design, the so-called overpackaging, the insufficient and inadequate recycling infrastructure, the weak market of recycled plastics and the high cost of waste treatment and disposal. The Circular economy package, the European Strategy for plastics in a circular economy and the recent European Green Deal include very ambitious programmes to rethink the entire plastic value chain. As regards packaging, all plastic packaging will have to be 100% recyclable (or reusable) and 55% recycled by 2030. Regions are consequently called upon to set up a robust plan able to fit the European objectives. It takes on greater importance in Emilia Romagna where the Packaging valley is located. This thesis supports the definition of a strategy aimed to establish an after-use plastics economy in the region. The PhD work has set the basis and the instruments to establish the so-called Circularity Strategy with the aim to turn about 92.000t of plastic waste into profitable secondary resources. System innovation, life cycle thinking and participative backcasting method have allowed to deeply analyse the current system, orientate the problem and explore sustainable solutions through a broad stakeholder participation. A material flow analysis, accompanied by a barrier analysis, has supported the identification of the gaps between the present situation and the 2030 scenario. Eco-design for and from recycling (and a mass _based recycling rate (based on the effective amount of plastic wastes turned into secondary plastics), valorized by a value_based indicator, are the key-points of the action plan.

Hemorrhagic Shock Secondary To Button Battery Ingestion.

Button battery ingestion is a frequent pediatric complaint. The serious complications resulting from accidental ingestion have increased significantly over the last two decades due to easy access to gadgets and electronic toys. Over recent years, the increasing use of lithium batteries of diameter 20 mm has brought new challenges, because these are more detrimental to the mucosa, compared with other types, with high morbidity and mortality. The clinical complaints, which are often nonspecific, may lead to delayed diagnosis, thereby increasing the risk of severe complications. A five-year-old boy who had been complaining of abdominal pain for ten days, was brought to the emergency service with a clinical condition of hematemesis that started two hours earlier. On admission, he presented pallor, tachycardia and hypotension. A plain abdominal x-ray produced an image suggestive of a button battery. Digestive endoscopy showed a deep ulcerated lesion in the esophagus without active bleeding. After this procedure, the patient presented profuse hematemesis and severe hypotension, followed by cardiorespiratory arrest, which was reversed. He then underwent emergency exploratory laparotomy and presented a new episode of cardiorespiratory arrest, which he did not survive. The battery was removed through rectal exploration. This case describes a fatal evolution of button battery ingestion with late diagnosis and severe associated injury of the digestive mucosa. A high level of clinical suspicion is essential for preventing this evolution. Preventive strategies are required, as well as health education, with warnings to parents, caregivers and healthcare professionals.

A Modified Acidic Approach For Dna Extraction From Plant Species Containing High Levels Of Secondary Metabolites.

Purified genomic DNA can be difficult to obtain from some plant species because of the presence of impurities such as polysaccharides, which are often co-extracted with DNA. In this study, we developed a fast, simple, and low-cost protocol for extracting DNA from plants containing high levels of secondary metabolites. This protocol does not require the use of volatile toxic reagents such as mercaptoethanol, chloroform, or phenol and allows the extraction of high-quality DNA from wild and cultivated tropical species.