The importance of pre-treatment of spent hydrotreating catalysts on metals recovery

This work describes a three-step pre-treatment route for processing spent commercial NiMo/Al2O3 catalysts. Extraction of soluble coke with n-hexane and/or leaching of foulant elements with oxalic acid were performed before burning insoluble coke under air. Oxidized catalysts were leached with 9 mol L-1 sulfuric acid. Iron was the only foulant element partially leached by oxalic acid. The amount of insoluble matter in sulfuric acid was drastically reduced when iron and/or soluble coke were previously removed. Losses of active phase metals (Ni, Mo) during leaching with oxalic acid were compensated by the increase of their recovery in the sulfuric acid leachate.

Hydrometallurgical recovery of valuable metals from secondary raw materials

Wastes and side streams in the mining industry and different anthropogenic wastes often contain valuable metals in such concentrations their recovery may be economically viable. These raw materials are collectively called secondary raw materials. The recovery of metals from these materials is also environmentally favorable, since many of the metals, for example heavy metals, are hazardous to the environment. This has been noticed in legislative bodies, and strict regulations for handling both mining and anthropogenic wastes have been developed, mainly in the last decade. In the mining and metallurgy industry, important secondary raw materials include, for example, steelmaking dusts (recoverable metals e.g. Zn and Mo), zinc plant residues (Ag, Au, Ga, Ge, In) and waste slurry from Bayer process alumina production (Ga, REE, Ti, V). From anthropogenic wastes, waste electrical and electronic equipment (WEEE), among them LCD screens and fluorescent lamps, are clearly the most important from a metals recovery point of view. Metals that are commonly recovered from WEEE include, for example, Ag, Au, Cu, Pd and Pt. In LCD screens indium, and in fluorescent lamps, REEs, are possible target metals. Hydrometallurgical processing routes are highly suitable for the treatment of complex and/or low grade raw materials, as secondary raw materials often are. These solid or liquid raw materials often contain large amounts of base metals, for example. Thus, in order to recover valuable metals, with small concentrations, highly selective separation methods, such as hydrometallurgical routes, are needed. In addition, hydrometallurgical processes are also seen as more environmental friendly, and they have lower energy consumption, when compared to pyrometallurgical processes. In this thesis, solvent extraction and ion exchange are the most important hydrometallurgical separation methods studied. Solvent extraction is a mainstream unit operation in the metallurgical industry for all kinds of metals, but for ion exchange, practical applications are not as widespread. However, ion exchange is known to be particularly suitable for dilute feed solutions and complex separation tasks, which makes it a viable option, especially for processing secondary raw materials. Recovering valuable metals was studied with five different raw materials, which included liquid and solid side streams from metallurgical industries and WEEE. Recovery of high purity (99.7%) In, from LCD screens, was achieved by leaching with H2SO4, extracting In and Sn to D2EHPA, and selectively stripping In to HCl. In was also concentrated in the solvent extraction stage from 44 mg/L to 6.5 g/L. Ge was recovered as a side product from two different base metal process liquors with Nmethylglucamine functional chelating ion exchange resin (IRA-743). Based on equilibrium and dynamic modeling, a mechanism for this moderately complex adsorption process was suggested. Eu and Y were leached with high yields (91 and 83%) by 2 M H2SO4 from a fluorescent lamp precipitate of waste treatment plant. The waste also contained significant amounts of other REEs such as Gd and Tb, but these were not leached with common mineral acids in ambient conditions. Zn was selectively leached over Fe from steelmaking dusts with a controlled acidic leaching method, in which the pH did not go below, but was held close as possible to, 3. Mo was also present in the other studied dust, and was leached with pure water more effectively than with the acidic methods. Good yield and selectivity in the solvent extraction of Zn was achieved by D2EHPA. However, Fe needs to be eliminated in advance, either by the controlled leaching method or, for example, by precipitation. 100% Pure Mo/Cr product was achieved with quaternary ammonium salt (Aliquat 336) directly from the water leachate, without pH adjustment (pH 13.7). A Mo/Cr mixture was also obtained from H2SO4 leachates with hydroxyoxime LIX 84-I and trioctylamine (TOA), but the purities were 70% at most. However with Aliquat 336, again an over 99% pure mixture was obtained. High selectivity for Mo over Cr was not achieved with any of the studied reagents. Ag-NaCl solution was purified from divalent impurity metals by aminomethylphosphonium functional Lewatit TP-260 ion exchange resin. A novel preconditioning method, named controlled partial neutralization, with conjugate bases of weak organic acids, was used to control the pH in the column to avoid capacity losses or precipitations. Counter-current SMB was shown to be a better process configuration than either batch column operation or the cross-current operation conventionally used in the metallurgical industry. The raw materials used in this thesis were also evaluated from an economic point of view, and the precipitate from a waste fluorescent lamp treatment process was clearly shown to be the most promising.

Industrial ecology applied to ELV management. Material and energy recovery from ASR

This PhD thesis reports on car fluff management, recycling and recovery. Car fluff is the residual waste produced by car recycling operations, particularly from hulk shredding. Car fluff is known also as Automotive Shredder Residue (ASR) and it is made of plastics, rubbers, textiles, metals and other materials, and it is very heterogeneous both in its composition and in its particle size. In fact, fines may amount to about 50%, making difficult to sort out recyclable materials or exploit ASR heat value by energy recovery. This 3 years long study started with the definition of the Italian End-of-Life Vehicles (ELVs) recycling state of the art. A national recycling trial revealed Italian recycling rate to be around 81% in 2008, while European Community recycling target are set to 85% by 2015. Consequently, according to Industrial Ecology framework, a life cycle assessment (LCA) has been conducted revealing that sorting and recycling polymers and metals contained in car fluff, followed by recovering residual energy, is the route which has the best environmental perspective. This results led the second year investigation that involved pyrolysis trials on pretreated ASR fractions aimed at investigating which processes could be suitable for an industrial scale ASR treatment plant. Sieving followed by floatation reported good result in thermochemical conversion of polymers with polyolefins giving excellent conversion rate. This factor triggered ecodesign considerations. Ecodesign, together with LCA, is one of the Industrial Ecology pillars and it consists of design for recycling and design for disassembly, both aimed at the improvement of car components dismantling speed and the substitution of non recyclable material. Finally, during the last year, innovative plants and technologies for metals recovery from car fluff have been visited and tested worldwide in order to design a new car fluff treatment plant aimed at ASR energy and material recovery.

Recuperação de metais de catalisadores usados de hidrotratamento (NiMo E CoMo/AL2O3)

This work presents a detailed study of the leaching behavior of deactivated hydrotreating catalysts (CoMo, NiMo/Al2O3) in presence of oxalate and NH4+ ions in various media. The yield of metals recovery may be optimized by adjusting several experimental parameters (time, temperature, etc). Leaching is limited by physical factors (diffusional effects caused by coke) and by the existence of silicate/spinel-like species which are poorly soluble in leaching solutions. Coke may be eliminated by an oxidation step at temperatures between 300-400ºC. Above 400ºC, solubilization of Ni and Co is drastically reduced. 50-90% wt of sulphate species and 15-30% wt of phosphate ions are solubilized during leaching. Silicon (as SiO2) is not solubilized. The best Ni-Co-Mo recoveries are in the 70-90% wt range; Fe recovery may be quantitative, whereas Al leaching may be lower than 5% wt.

Gerenciamento de resíduos laboratoriais: recuperação de elementos e preparo para descarte final

This work shows some laboratory waste management developed in order to recover some elements or to prepare the waste for a correct final disposal. The 25 elements chosen cover basically all chemical behaviors found for the metals in the Periodic Table. The treatments adopted were based on the classical behavior in aqueous solution (wet chemistry) but an important condition for a full success was the previous knowledge of the qualitative composition of the wastes treated. Some general trends were found: the final liquid waste was always saline and normally presented a higher volume than the original waste; most original wastes were acid in nature; steps such as solid-liquid separation, washing, evaporating and calcining were currently performed. This work was also a very good experience in chemistry in solution for students and showed them the need of treating wastes for a better environment.

Recuperação de metais de catalisadores mássicos e monometálicos

This work presents a study on the dissolution of some commercial monometallic and non-supported deactivated catalysts in HF + H2O2 mixtures (and, eventually, other media) under mild experimental conditions, after a previous oxidation step. The samples were neither crushed nor grinded. The best experimental conditions were dependent on the nature of the support and of the active phase. For example, the Pt/Al2O3 catalyst was dissolved in about 10 minutes, without agitation and heating; however, dissolution of the Pd/Al2O3, Ni/Al2O3, Ni/SiO2, Cu/Al2O3 and V2O5 samples required a temperature of 60 ºC and an agitation of 400 rpm. A careful addition of a NaOH solution allowed a quantitative precipitation of aluminium as criolite (Na3AlF6) or precipitation of Si as Na2SiF6; NaF was obtained as a by-product. As expected, processing of Pd/C, V2O5 and CuO.Cr2O3 samples was relatively simple. Metals recovery from catalysts reached a quantitative level in all samples studied; it is particularly interesting that platinum and palladium could be easily recovered in a single step process, thus separing them from aluminium.

Processamento de pilhas Li/MnO2 usadas

This work presents two recycling processes for spent Li/MnO2 batteries. After removal of the solvent under vacuum the cathode + anode + electrolyte was submitted to one of the following procedures: (a) it was calcined (500 ºC, 5 h) and the calcined solid was submitted to solvent extraction with water in order to recover lithium salts. The residual solid was treated with sulfuric acid containing hydrogen peroxide. Manganese was recovered as sulfate; (b) the solid was treated with potassium hydrogeno sulfate (500 ºC, 5 h). The solid was dissolved in water and the resulting solution was added dropwise to sodium hydroxide. Manganese was recovered as dioxide. The residual solution was treated with potassium fluoride in order to precipitate lithium fluoride.

Recuperação de chumbo, mercúrio e elementos dos grupos 4 a 7 da tabela periódica de seus resíduos

This work shows routes to recover some elements from their laboratory wastes and broken apparatus (thermometers and densimeters). Most elements chosen present a chemical behavior in aqueous solution which is not currently studied in the ordinary experimental classes. The routes were based on the previous knowledge of the qualitative composition of the wastes treated. Wastes containing chromium were the most difficult to treat. The elements were recovered in good yields and can be reused in new experiments. This work was a very good experience in chemistry for students and shows the need of managing wastes for a better environment.

Processamento de placas de circuito impresso de equipamentos eletroeletrônicos de pequeno porte

A hydrometallurgical process applicable to printed circuit boards of small electrical and electronic devices was developed. This involved three leaching steps (60 ºC, 2 h): 6 mol L-1 NaOH, 6 mol L-1 HCl and aqua regia. NaOH removed the resin and flame retardant that covered the circuit boards. HCl dissolved the most electropositive metals and a small amount of copper (~0.3 wt%). Aqua regia dissolved the noble metals. Silver precipitated as AgCl. Gold and platinum were quantitatively extracted with pure methyl-isobutylketone and Alamine 336 (10 % vol. in kerosene), respectively. Slow evaporation of the raffinate crystallized CuCl2.4H2O (89% yield).

Estudo eletroquímico da recuperação de metais de pilhas e de baterias descartadas após o uso

O objetivo da pesquisa é recuperar os principais metais presentes em um lote com uma mistura de diversos tipos de pilhas e de baterias descartadas após o uso, lote obtido em um posto de coleta. Para esse estudo, o resíduo das pilhas e das baterias foi moído, reduzido em forno elétrico, submetido à separação magnética e lixiviado. A composição química, após a lixiviação, foi reproduzida em uma solução sintética, que foi submetida à extração por solventes e reextração sendo que as soluções obtidas, após as reextrações, foram utilizadas como eletrólitos. Manganês, cobre, cobalto e níquel são recuperados na forma metálica após um tratamento que inclui as etapas pirometalúrgica, hidrometalúrgica e eletroquímica. Estudos anteriores definiram os parâmetros das etapas pirometalúrgica, lixiviação e extração por solventes que proporcionaram separação mais seletiva dos íons metálicos que se pretende recuperar. A contribuição do presente estudo é encontrar um processo que trate de todos os tipos de pilhas e de baterias juntos e recuperar seus metais mais importantes, evitando, assim, a etapa de separação prévia das baterias. Os filmes foram analisados quanto à sua espessura e composição.

Reciclagem de resíduos eletroeletrônicos: um estudo cinético da lixiviação ácida de ferro de placas de circuito impresso de microcomputadores.

O aumento no consumo mundial de novos aparelhos eletroeletrônicos aliado à redução no tempo de vida útil destes equipamentos tem como principal consequência ao meio ambiente a geração de resíduos. No Brasil, com a instituição da Política Nacional de Resíduos Sólidos, criou-se a obrigatoriedade legal da responsabilidade dos fabricantes pela logística reversa dos equipamentos eletroeletrônicos, incentivando pesquisas para o desenvolvimento dos métodos de reciclagem e tratamento dos materiais descartados. O processo de lixiviação foi avaliado como alternativa à etapa de separação magnética presente nas atuais rotas hidrometalúrgicas para recuperação de metais valiosos de placas de circuito impresso. Para avaliar a composição das placas, foi realizado ensaio de dissolução em água régia. As amostras foram moídas e submetidas a ensaios de lixiviação com ácido sulfúrico nas concentrações de 1 e 2mol/L, às temperaturas de 75ºC, 85ºC e 95ºC, durante 24 horas. Com ácido sulfúrico 2mol/L a 95ºC, o tempo necessário para se obter 100% de extração do ferro foi de 2 horas. Nestas condições, não foi detectada a presença de cobre dissolvido. A cinética da reação é controlada por reação química e obedece a equação .=1(1)3. A energia de ativação aparente do processo equivale a 90kJ/mol.

Sustainability analysis in the mining sector: a case study on new recycling technologies for sulphidic mine residues valorisation

Research has demonstrated that mining activities can cause serious impacts on the environment, as well as the surrounding communities, mainly due to the unsafe storage of mine tailings. This research focuses on the sustainability assessment of new technologies for the recovery of metals from mine residues. The assessment consists in the evaluation of the environmental, economic, and social impacts through the Life Cycle based methods: Life Cycle Assessment (LCA), Life Cycle Costing (LCC), and Social Life Cycle Assessment (SLCA). The analyses are performed on the Mondo Minerals bioleaching project, which aim is to recover nickel and cobalt from the Sotkamo and Vuonos mine tailings. The LCA demonstrates that the project contributes to the avoided production of nickel and cobalt concentrates from new resources, hence reducing several environmental impacts. The LCC analysis shows that the company’s main costs are linked to the bioleaching process, caused by electricity consumption and the chemicals used. The SLCA analyses the impacts on three main stakeholder categories: workers, local community, and society. The results demonstrated that a fair salary (or the absence of it) impacts the workers the most, while the local community stakeholder category impacts are related to the access to material resources. The health and safety category is the most impacted category for the society stakeholder. The environmental and economic analyses demonstrate that the recovery of mine tailings may represents a good opportunity for mine companies both to reduce the environmental impacts linked to mine tailings and to increase the profitability. In particular, the project helps reduce the amounts of metals extracted from new resources and demonstrates that the use of the bioleaching technology for the extraction of metals can be economically profitable.

Spent NiMH batteries-The role of selective precipitation in the recovery of valuable metals

The production of electronic equipment, such as computers and cell phones, and, consequently, batteries, has increased dramatically. One of the types of batteries whose production and consumption has increased in recent times is the nickel metal hydride (NiMH) battery. This study evaluated a hydrometallurgical method of recovery of rare earths and a simple method to obtain a solution rich in Ni-Co from spent NiMH batteries. The active materials from both electrodes were manually removed from the accumulators and leached. Several acid and basic solutions for the recovery of rare earths were evaluated. Results showed that more than 98 wt.% of the rare earths were recovered as sulfate salts by dissolution with sulfuric acid, followed by selective precipitation at pH 1.2 using sodium hydroxide. The complete process. precipitation at pH 1.2 followed by precipitation at pH 7, removed about 100 wt.% of iron and 70 wt.% of zinc from the leaching solution. Results were similar to those found in studies that used solvent extraction. This method is easy, economic, and does not pose environmental threats of solvent extraction. (C) 2009 Elsevier B.V. All rights reserved.

Waste recovery into activated carbon for water purification from heavy metals

Dissertação apresentada para obtenção do Grau de Doutor em Engenharia Química Pela Universidade Nova de Lisboa,Faculdade de Ciências e Tecn

Roasting and Leaching Bulk Copper-Zinc Sulfide Concentrates with the Subsequent Recovery of the Metals by Electrolysis

The aim of this research was to investigate the possibilities of roasting and leaching a bulk copper-zinc sulfide concentrate, and the subsequent separation of the metals from the leach solution by electro­lytic deposition.