Variação da massa específica da madeira de Eucalyptus grandis aos 8 anos de idade em função de diferentes níveis de produtividade

It were analyzed Eucalyptus grandis trees of 8 years old in the forest group of Duraflora S/A, with different annual increments based on volume, to the related studies of specific gravity values based on productivity indexes. The methodology used in analysis of specific gravity was the gamma-ray attenuation technique of Americium-241. The Eucalyptus grandis showed a specific gravity decreasing with the increasing of parcel productivity. For a gain of 3,5 m3 in productivity there was a decreasing of 1% in specific gravity. Nevertheless, it was not observed correlation between specific gravity and basal area in a same parcel. The present work stands out too, some of the difficulties found with relation to wood specific gravity determinations and emphasize the importance of take samples in the form of full rounded plates in three or four relative positions in the tree.

Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial

VARELA, M. L. et al. Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial. Cerâmica, v.55, n.334 p.209-215. 2009.ISSN 0366-6913.Disponível em: . Acesso em: 06 out. 2010.

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Efeito da adição de carbonatos em formulação de massa para revestimento cerâmico utilizando matérias-primas do Piauí

Piauí state is a major producer of traditional red ceramic burning as bricks, tiles and ceramic tiles, with its main production center located in the city of Teresina. The state has large reserves of raw materials that can be used in the ceramic coating as clays, quartz, talc and carbonates. However, in the preparation of ceramic bodies using only a mixture of clays with different characteristics. The study aims to evaluate the effect of adding two types of carbonates in the ceramic semiporous mass coating produced in Piauí and then to verify the potential use of these carbonates as supplementary raw material product manufactured or the feasibility of obtaining a ceramic plate that meets the specifications for the porous coating. For this, were characterized the ceramic Piauí coating mass, a calcitic carbonate and a dolomitic, were made in the levels of 2, 4, 8, 16, and 32%. The masses were formed by pressing and burneds in two environments: a laboratory furnace (1080°C, 1120°C, 1140°C, and 1160°C) and an industrial furnace (1140°C). Then, following tests of linear shrinkage water absorption, apparent porosity, bulk density and flexural strength. Furthermore, the fired specimens were tested for their macrostructure and microstructure. The results showed the possibility of using the carbonate in ceramic mass flooring produced in Piauí, as added in small proportions improved dimensional stability and increased mechanical strength of ceramics pieces. It also proved itself possible to produce porous coating when added in higher levels

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Efeito da introdução de resíduo de cinza de forno cerâmico em massa para cerâmica estrutural

The red ceramics and structural ceramics, as they are known, include ceramic materials made by blocks of seals and structures, bricks, tiles, smail flagstones manacles, rustic floors and ornamental materials. Their fabrication uses raw material such as clay and clay sites, with some content of impurity. It has good durability and mechanical strength to compression, low cost, making it one of the mainly used materials in civil engineering. The incorporation of many industrial activities residue to ceramic products is a technological alternative for reducing the environmental impact caused by its carefree disposal. This incorporation can promote chemical change and inertness of metals from residue, by fixation in the glassy phase of ceramic during the burning stage. The main aim of this project is to study the technical feasibility of the addition of ceramic oven ash into formulations of mass for structural ceramics. In this project two kinds of clay (plastic and non-plastic) were used, as well as the ash from firewood used in the process of burning of structural ceramics. A group of experiments was outlined, which permitted the evaluation of the influence of the burning cycle in different temperatures of the ash content in formulations for ceramic blocks through technological properties, mechanical behavior and microstructure. Five samples were processed of each one of the masses of plastic and non-plastic clay without addition of ash and with addition of ash on the percentages of 10 % and 20 %, for temperatures of 850 °C, 950 °C, 1050 °C and 1150 °C, obtained through sinterization process. Among the studied compositions, the one which presented best performance was the mass of clay with 10 % of ash, at temperature of 1150 °C, with the smallest absorption of water, the smallest apparent porosity, specific apparent mass a bit over the others and greatest mechanical resistance to flexion. The composition made confirmed the technical feasibility of the use of ash in the mass for structural ceramics with maintenance of its necessary characteristics for its purposes

Estudo de formulação de massa para aplicação em placas cerâmicas

The sector of civil construction is strongly related to the red ceramic industry. This sector uses clay as raw material for manufacturing of various products such as ceramic plates. In this study, two types of clay called clay 1 and clay 2 were collected on deposit in Ielmo Marinho city (RN) and then characterized by thermogravimetric analysis (TG/DTG), differential thermal analysis (DTA), X-ray diffraction (XRD), X-ray fluorescence (XRF), rational analysis and particle size distribution and dilatometric analyses. Ceramic plates were manufactured by uniaxial pressing and by extrusion. The plates obtained by pressing were produced from the four formulations called 1, 2, 3 and 4, which presented, respectively, the following proportions by mass: 66.5% clay 1 and 33.5% clay 2, 50% clay 1 and 50% clay 2, 33.5% clay 1 and 66.5% clay 2, 25% clay 1 and 75% clay 2. After firing at 850, 950 and 1050 °C with heating rate of 10 °C/min and soaking time of 30 minutes, the following technological properties were determined: linear firing shrinkage, water absorption, apparent porosity, apparent specific mass and tensile strength (3 points). The formulation containing 25% clay 1 produced plates with most satisfactory results of water absorption and mechanical resistance, because of that it was chosen for manufacturing plates by extrusion. A single firing cycle was established for these plates, which took place as follow: heating rate of 2 °C/min up to 600 ºC with soaking time of 60 minutes, followed by heating using the same rate up to 1050 ºC with soaking time of 30 minutes. After this cycle, the same technological properties investigated in the plates obtained by pressing were determined. The results indicate (according to NRB 13818/1997) that the plates obtained by pressing from the mixture containing 25 wt% clay 1, after firing at 1050 °C, reach the specifications for semi-porous coating (BIIb). On the other hand, the plates obtained by extrusion were classified as semi-stoneware (group AIIa)

Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial

VARELA, M. L. et al. Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial. Cerâmica, v.55, n.334 p.209-215. 2009.ISSN 0366-6913.Disponível em: . Acesso em: 06 out. 2010.

Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial

VARELA, M. L. et al. Influência da adição de resíduo de caulim nas propriedades tecnológicas de uma massa padrão de porcelanato produzido em escala industrial. Cerâmica, v.55, n.334 p.209-215. 2009.ISSN 0366-6913.Disponível em: . Acesso em: 06 out. 2010.

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Efeito da adição de carbonatos em formulação de massa para revestimento cerâmico utilizando matérias-primas do Piauí

Piauí state is a major producer of traditional red ceramic burning as bricks, tiles and ceramic tiles, with its main production center located in the city of Teresina. The state has large reserves of raw materials that can be used in the ceramic coating as clays, quartz, talc and carbonates. However, in the preparation of ceramic bodies using only a mixture of clays with different characteristics. The study aims to evaluate the effect of adding two types of carbonates in the ceramic semiporous mass coating produced in Piauí and then to verify the potential use of these carbonates as supplementary raw material product manufactured or the feasibility of obtaining a ceramic plate that meets the specifications for the porous coating. For this, were characterized the ceramic Piauí coating mass, a calcitic carbonate and a dolomitic, were made in the levels of 2, 4, 8, 16, and 32%. The masses were formed by pressing and burneds in two environments: a laboratory furnace (1080°C, 1120°C, 1140°C, and 1160°C) and an industrial furnace (1140°C). Then, following tests of linear shrinkage water absorption, apparent porosity, bulk density and flexural strength. Furthermore, the fired specimens were tested for their macrostructure and microstructure. The results showed the possibility of using the carbonate in ceramic mass flooring produced in Piauí, as added in small proportions improved dimensional stability and increased mechanical strength of ceramics pieces. It also proved itself possible to produce porous coating when added in higher levels

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Estudo da correlação entre as características da matéria-prima graxa e as propriedades físico-químicas do biodiesel

A possibilidade de utilização de várias matérias graxas na produção do biodiesel nacional é um fator diferencial em relação aos outros países e requer um conhecimento mais profundo das particularidades do biodiesel obtido a partir de matérias-primas tão distintas. Neste contexto, se insere a presente pesquisa, em que se buscou estabelecer correlações entre algumas propriedades do biodiesel e a fonte oleaginosa que lhe deu origem. O biodiesel foi obtido a partir da reação de transesterificação etílica de dez diferentes matérias-primas graxas (óleos refinados de soja, arroz, canola, girassol, milho, oliva, cyclus (mistura contendo óleos de canola, milho e girassol); óleos brutos de mamona e murumuru, além de resíduo de fritura), utilizando etanolato de potássio como agente catalítico, em um reator com sistema de refluxo a 70C durante uma hora. Após purificação, foram determinadas algumas propriedades do biodiesel (massa específica, viscosidade, índice de acidez e índice de iodo) e da matéria-prima (massa específica, viscosidade, índice de acidez, índice de iodo e composição) que lhe deu origem. Os resultados obtidos nas caracterizações geraram gráficos de correlações entre os diversos parâmetros e os dados foram analisados estatisticamente pelo método de correlações canônicas. Para todas as amostras de biodiesel, os valores obtidos nas caracterizações foram compatíveis com as especificações estabelecidas pela ANP para o produto, com exceção do biodiesel de murumuru (índice de acidez elevado e viscosidade baixa) e do biodiesel de mamona (viscosidade e massa específica elevadas). Os dados estatísticos demonstram altas correlações entre o biodiesel (massa específica (87,4%), viscosidade (98,5%) e índice de acidez (82,8%)) e as matérias-primas (massa específica (92,1%) e viscosidade (99,3%)). Além disso, existe uma grande correlação entre o índice de iodo (84,5%) do biodiesel e o índice de iodo (77,2%) e a massa molar dos ésteres na faixa de C16-C18 (MMTG) presentes na matéria-prima (89,1%). Estes resultados estatísticos ratificam as observações analíticas

Microtomografia com Raio X e processamento de imagem na obtenção da porosidade do concreto

O objetivo principal desse trabalho foi utilizar métodos não destrutivos (END), como a microtomografia com Raio X e técnicas de obtenção e processamento de imagens, para obtenção da porosidade do concreto. Foram utilizados dois métodos. Em um método as imagens foram obtidas por meio de microtomografia por Raio X e no outro foi utilizado um escâner comercial para obtenção das imagens. Essas imagens foram processadas por meio de técnicas de processamento de pixel e morfologia matemática. Os resultados obtidos para a porosidade foram comparados com resultado obtido por meio do método proposto pela NBR 9778 (2005) (Absorção de água, índice de vazios e massa específica em argamassa e concreto endurecido). As imagens microtomográficas das amostras de concreto foram obtidas num sistema Skyscan 1172 com 256 tons de cinza, ajustadas em contraste, binarizadas e filtradas. No outro método foi utilizado um Escâner Comercial com resolução de 2400 dpi para adquirir as imagens, sendo também utilizadas técnicas de processamento de pixel e morfologia matemática para processá-las. Os resultados dos valores da porosidade mostraram compatibilidade entre os dois métodos apresentados e o método proposto pela NBR 9778 (2005). Observou-se que os resultados obtidos por microtomografia foram mais confiáveis, mas o método utilizando o escâner comercial se apresentou como um método aceitável por seus resultados e principalmente por seu baixo custo e facilidade de operação.

Medição experimental e previsão de velocidade do som de componentes de biocombustíveis

A velocidade do som é uma propriedade que vem sendo cada vez mais utilizada em diferentes áreas tecnológicas. Além disso, a velocidade do som é uma propriedade termodinâmica que está associada a outras propriedades do meio como a compressibilidade isentrópica e isotérmica, entre outras. Neste contexto, muitos estudos foram realizados a fim de obter modelos precisos que possam representar fielmente a velocidade do som, sendo observados desvios absolutos médios entre 0,13 e 24,8%. Neste trabalho, um banco de dados de velocidade do som e massa específica à pressão atmosférica de n-alcanos, alcanos ramificados, n-alcenos, aromáticos, alcoóis, éteres e ésteres, foram compilados da literatura aberta. Utilizando estes dados e baseando-se no modelo de Wada por contribuição de grupo recentemente proposto, foi desenvolvido um novo modelo por contribuição atômica para predizer a velocidade do som de todas as famílias dos compostos investigados neste trabalho. É mostrado que o modelo proposto é capaz de prever a velocidade do som para os compostos destas famílias com desvios próximos da incerteza experimental calculada a partir de diferentes dados da literatura. Este trabalho também discute o efeito da ramificação das cadeias na constante Wada, ressaltando a importância de novas medições para este tipo de compostos. Além disso, observou-se que a literatura necessita de mais dados experimentais de velocidade do som, à pressão atmosférica e diferentes temperaturas para substâncias puras presentes em biodiesel e bio-óleo de pirólise rápida. Neste contexto, o presente trabalho fornece novos dados experimentais de velocidade do som e massa específica de cinco ésteres metílicos de ácidos graxos, também conhecidos como FAMEs, (caprilato de metila, caprato de metila, palmitato de metila, estearato de metila e linoleato de metila), e sete componentes puros presentes em bio-óleo de pirólise à pressão atmosférica, de vários fenóis (fenol, o-, m- e p-cresol), dois éteres fenólicos (2-metoxifenol e eugenol) e um éster fenólico (salicilato de metila), a temperaturas de (288,15-343,15) K. O modelo preditivo de Wada atômico foi utilizado para calcular a velocidade do som dos FAMEs estudados neste trabalho, e os desvios foram comparados com o modelo de Wada por contribuição de grupo. O modelo atômico de Wada foi utilizado para prever a velocidade do som dos componentes puros presentes no bio-óleo de pirólise rápida experimentalmente estudados nesta dissertação. Além disso, os dados de massa específica e velocidade de som foram correlacionados com o modelo de Prigogine-Flory-Patterson (PFP). As propriedades foram bem representadas pelo modelo PFP, no entanto, para a velocidade do som o modelo apresenta desvios sistemáticos na dependência com a temperatura. O desempenho do modelo preditivo de Wada atômico foi considerado satisfatório, devido os desvios observados serem compatíveis ou até menores do que os desvios típicos obtidos na literatura com outros modelos correlativos para o cálculo da velocidade do som de outras substâncias