Ottimizzazione del consumo dei grassi durante esercizio fisico: studio di un test per il target mirato di allenamento individuale

Il primo studio ha verificato l'affidabilità del software Polimedicus e gli effetti indotti d'allenamento arobico all’intensità del FatMax. 16 soggetti sovrappeso, di circa 40-55anni, sono stati arruolati e sottoposti a un test incrementale fino a raggiungere un RER di 0,95, e da quel momento il carico è stato aumentato di 1 km/ h ogni minuto fino a esaurimento. Successivamente, è stato verificato se i valori estrapolati dal programma erano quelli che si possono verificare durante a un test a carico costante di 1ora. I soggetti dopo 8 settimane di allenamento hanno fatto un altro test incrementale. Il dati hanno mostrato che Polimedicus non è molto affidabile, soprattutto l'HR. Nel secondo studio è stato sviluppato un nuovo programma, Inca, ed i risultati sono stati confrontati con i dati ottenuti dal primo studio con Polimedicus. I risultati finali hanno mostrato che Inca è più affidabile. Nel terzo studio, abbiamo voluto verificare l'esattezza del calcolo del FatMax con Inca e il test FATmaxwork. 25 soggetti in sovrappeso, tra 40-55 anni, sono stati arruolati e sottoposti al FATmaxwork test. Successivamente, è stato verificato se i valori estrapolati da INCA erano quelli che possono verificarsi durante un carico di prova costante di un'ora. L'analisi ha mostrato una precisione del calcolo della FatMax durante il carico di lavoro. Conclusione: E’ emersa una certa difficoltà nel determinare questo parametro, sia per la variabilità inter-individuale che intra-individuale. In futuro bisognerà migliorare INCA per ottenere protocolli di allenamento ancora più validi.

Análise do comportamento de estruturas através de ensaios de carga

A engenharia civil, rege-se pela garantia de segurança e de funcionalidade das obras que projeta e executa. Para cumprir tais requisitos, é necessário durante a sua vida útil, no final da construção, reforço ou reabilitação, proceder à avaliação da conformidade entre o comportamento real da estrutura e os pressupostos subjacentes ao projeto. Esta dissertação tem como objetivo a compreensão e análise do comportamento estrutural da Ponte sobre o Rio Sorraia, através da realização de ensaios de carga apoiados pela conceção de um modelo numérico devidamente calibrado, capaz de simular a resposta da estrutura, o mais próximo possível do observável na realidade. Para alcançar o objetivo pré definido elencam-se as metodologias relevantes, descrevem-se os tipos de ensaios de carga realizados em pontes/viadutos e faz-se referência aos aparelhos de medição que estão na base da instrumentação aplicada em obras. Esta introdução foca-se ainda na modelação numérica, permitindo o conhecimento básico necessário para a criação e atualização de modelos numéricos de pontes. Relativamente ao caso de estudo expõe-se a realização do ensaio de carga, descrevendo todo o processo, bem como os resultados obtidos ao nível das grandezas de medição estudadas. Aqui é concebido um modelo numérico base da ponte, alvo de discussão ao nível do comportamento estrutural, baseada na validação dos resultados obtidos por via experimental, através da comparação com os obtidos por via numérica. Por fim, o estudo e seleção de diversos parâmetros da modelação, facultando a calibração do modelo numérico da ponte. Os resultados obtidos neste modelo comprovam o seu elevado potencial, no apoio à observação e compreensão do comportamento de estruturas através da realização de ensaios de carga. O sucesso da realização de uma análise do comportamento de estruturas, através de ensaios de carga, depende assim fundamentalmente, da correta execução do ensaio, da correta conceção e atualização do modelo numérico e da interligação entre os resultados experimentais e numéricos.

Diagnóstico e ensaio de carga de asnas tradicionais de madeira

Dissertação de mestrado Integrado em Engenharia Civil

Composite Precast Prestressed Concrete Bridge Slabs, HR-310, 1991

Precast prestressed concrete panels have been used as subdecks in bridge construction in Iowa and other states. To investigate the performance of these types of composite slabs at locations adjacent to abutment and pier diaphragms in skewed bridges, a research prcject which involved surveys of design agencies and precast producers, field inspections of existing bridges, analytical studies, and experimental testing was conducted. The survey results from the design agencies and panel producers showed that standardization of precast panel construction would be desirable, that additional inspections at the precast plant and at the bridge site would be beneficial, and that some form of economical study should be undertaken to determine actual cost savings associated with composite slab construction. Three bridges in Hardin County, Iowa were inspected to observe general geometric relationships, construction details, and to note the visual condition of the bridges. Hairline cracks beneath several of the prestressing strands in many of the precast panels were observed, and a slight discoloration of the concrete was seen beneath most of the strands. Also, some rust staining was visible at isolated locations on several panels. Based on the findings of these inspections, future inspections are recommended to monitor the condition of these and other bridges constructed with precast panel subdecks. Five full-scale composite slab specimens were constructed in the Structural Engineering Laboratory at Iowa State University. One specimen modeled bridge deck conditions which are not adjacent to abutment or pier diaphragms, and the other four specimens represented the geometric conditions which occur for skewed diaphragms of 0, 15, 30, and 40 degrees. The specimens were subjected to wheel loads of service and factored level magnitudes at many locations on the slab surface and to concentrated loads which produced failure of the composite slab. The measured slab deflections and bending strains at both service and factored load levels compared reasonably well with the results predicted by simplified Finite element analyses of the specimens. To analytically evaluate the nominal strength for a composite slab specimen, yield-line and punching shear theories were applied. Yield-line limit loads were computed using the crack patterns generated during an ultimate strength test. In most cases, these analyses indicated that the failure mode was not flexural. Since the punching shear limit loads in most instances were close to the failure loads, and since the failure surfaces immediately adjacent to the wheel load footprint appeared to be a truncated prism shape, the probable failure mode for all of the specimens was punching shear. The development lengths for the prestressing strands in the rectangular and trapezoidal shaped panels was qualitatively investigated by monitoring strand slippage at the ends of selected prestressing strands. The initial strand transfer length was established experimentally by monitoring concrete strains during strand detensioning, and this length was verified analytically by a finite element analysis. Even though the computed strand embedment lengths in the panels were not sufficient to fully develop the ultimate strand stress, sufficient stab strength existed. Composite behavior for the slab specimens was evaluated by monitoring slippage between a panel and the topping slab and by computation of the difference in the flexural strains between the top of the precast panel and the underside of the topping slab at various locations. Prior to the failure of a composite slab specimen, a localized loss of composite behavior was detected. The static load strength performance of the composite slab specimens significantly exceeded the design load requirements. Even with skew angles of up to 40 degrees, the nominal strength of the slabs did not appear to be affected when the ultimate strength test load was positioned on the portion of each slab containing the trapezoidal-shaped panel. At service and factored level loads, the joint between precast panels did not appear to influence the load distribution along the length of the specimens. Based on the static load strength of the composite slab specimens, the continued use of precast panels as subdecks in bridge deck construction is recommended.

Heavy Agricultural Loads on Pavements and Bridges, HR-1073, 1999

During the harvest season in Iowa, it is common to have single axle loads on secondary roads and bridges that are excessive (typical examples are grain carts) and well beyond normal load limits. Even though these excessive loads occur only during a short time of the year, they may do significant damage to pavements and bridges. In addition, the safety of some bridges may be compromised because of the excessive loads, and sometimes there may be little indication to the users that damage may be imminent. At this time there are no Iowa laws regulating axle loads allowed for agricultural equipment. This study looks at the potential problems this may cause on secondary roads and timber stringer bridges. Both highway pavement and timber bridges are evaluated in this report. A section (panel) of Iowa PCC paved county road was chosen to study the effects of heavy agricultural loads on pavements. Instrumentation was applied to the panel and a heavily loaded grain cart was rolled across. The collected data were analyzed for any indication of excessive stresses of the concrete. The second study, concerning excessive loads on timber stringer bridges, was conducted in the laboratory. Four bridge sections were constructed and tested. Two of the sections contained five stringers and two sections had three stringers. Timber for the bridges came from a dismantled bridge, and deck panels were cut from new stock. All timber was treated with creosote. A hydraulic load was applied at the deck mid-span using a foot print representing a tire from a typical grain cart. Force was applied until failure of the system resulted. The collected data were evaluated to provide indications of load distribution and for comparison with expected wheel loads for a typical heavily loaded single axle grain cart. Results of the pavement tests showed that the potential of over-stressing the pavement is a possibility. Even though most of the tension stress levels recorded were below the rupture strength of the concrete, there were a few instances where the indicated tension stress level exceeded the concrete rupture strength. Results of the bridge tests showed that when the static ultimate load capacity of the timber stringer bridge sections was reached, there was sudden loss of capacity. Prior to reaching this ultimate capacity, the load sharing between the stringers was very uniform. The failure was characterized by loss of flexural capacity of the stringers. In all tests, the ultimate test load exceeded the wheel load that would be applied by an 875 bushel single axle grain cart.

Caracterització del temps de vol en relació amb variables biomecàniques de l’estirada en l’arrencada d’halterofília

L’objecte del present estudi és caracteritzar el temps de vol (Tv) de la fase aèria en l’exercici d’arrencada en halterofília. Es descriu el seu comportament en funció de l’increment progressiu de la càrrega i en relació a variables biomecàniques de l’estirada, així com la seva evolució en un cicle d’entrenament. Es va fer un test màxim de càrregues progressives amb set halterofilistes (n = 7) de competició. Mitjançant els sistemes de valoració Musclelab i Chronojump es van registrar els valors de: força (F), potència (P), velocitat (V), pic de velocitat (pV) i alçada relativa (Hrel ) de la barra en l’estirada, al costat del Tv del desplaçament dels peus de l’aixecador a l’entrada sota la barra. Es va observar una moderada correlació negativa (r = –0,561; p < 0,01) entre el Tv i la càrrega màxima del test (%1RMT). No es van trobar correlacions significatives per al Tv respecte a la resta de variables analitzades. El Tv disminuïa amb l’increment de la càrrega en rangs submàxims, i era de natura aleatòria amb l’ocupació de càrregues màximes. En un subgrup de la mostra (n = 4) es van valorar les mateixes variables passades vuit setmanes. El Tv, la Pmàx i el pV suggereixen ser variables suficientment sensibles per monitoritzar els canvis generats per l’entrenament en vuit setmanes, encara que la reduïda dimensió mostral no va permetre aconseguir diferències significatives. Aquests resultats destaquen la possibilitat de considerar el Tv i la P com a mesures de control en l’entrenament d’halterofilistes, preferentment en l’ús de càrregues submàximes.

Quantifying the residual creep life of polyester mooring ropes

This paper assesses the ARELIS (Assured Residual Life Span) method for estimating residual creep life of polyester rope used in deepwater mooring lines. A statistical model has been developed to quantify the uncertainties in the method, such as the scatter in creep rupture test data and load sharing between sub-ropes. This model can be used to determine the required test load, duration and number of ARELIS tests, in order to guarantee a minimum creep life for a mooring line at its service load. Creep rupture tests have been performed to provide input for the statistical model.

Next Generation Catalogs (NGCs) : Meeting User Needs with Metadata and Search Technology

Recommendations • Become a beta partner with vendor • Test load collections before going live • Update cataloging codes to benefit your community • Don’t expect to drastically change cataloging practices

Experimental characterization of the out-of-plane performance of regular stone masonry walls, including test setups and axial load influence

Stone masonry is one of the oldest and most worldwide used building techniques. Nevertheless, the structural response of masonry structures is complex and the effective knowledge about their mechanical behaviour is still limited. This fact is particularly notorious when dealing with the description of their out-of-plane behaviour under horizontal loadings, as is the case of the earthquake action. In this context, this paper describes an experimental program, conducted in laboratory environment, aiming at characterizing the out-of-plane behaviour of traditional unreinforced stone masonry walls. In the scope of this campaign, six full-scale sacco stone masonry specimens were fully characterised regarding their most important mechanic, geometric and dynamic features and were tested resorting to two different loading techniques under three distinct vertical pre-compression states; three of the specimens were subjected to an out-of-plane surface load by means of a system of airbags and the remaining were subjected to an out-of-plane horizontal line-load at the top. From the experiments it was possible to observe that both test setups were able to globally mobilize the out-of-plane response of the walls, which presented substantial displacement capacity, with ratios of ultimate displacement to the wall thickness ranging between 26 and 45 %, as well as good energy dissipation capacity. Finally, very interesting results were also obtained from a simple analytical model used herein to compute a set of experimental-based ratios, namely between the maximum stability displacement and the wall thickness for which a mean value of about 60 % was found.

Comparing different methods to measure biofilm thickness: the techniques are: optical coherence tomography, confocal laser scanning microscopy and low load compression test

Dissertação de mestrado integrado em Engenharia Biomédica (área de especialização em Engenharia Clínica)

Spectral analysis of the electromyograph of the erector spinae muscle before and after a dynamic manual load-lifting test

The aim of the present study was to assess the spectral behavior of the erector spinae muscle during isometric contractions performed before and after a dynamic manual load-lifting test carried out by the trunk in order to determine the capacity of muscle to perform this task. Nine healthy female students participated in the experiment. Their average age, height, and body mass (± SD) were 20 ± 1 years, 1.6 ± 0.03 m, and 53 ± 4 kg, respectively. The development of muscle fatigue was assessed by spectral analysis (median frequency) and root mean square with time. The test consisted of repeated bending movements from the trunk, starting from a 45º angle of flexion, with the application of approximately 15, 25 and 50% of maximum individual load, to the stand up position. The protocol used proved to be more reliable with loads exceeding 50% of the maximum for the identification of muscle fatigue by electromyography as a function of time. Most of the volunteers showed an increase in root mean square versus time on both the right (N = 7) and the left (N = 6) side, indicating a tendency to become fatigued. With respect to the changes in median frequency of the electromyographic signal, the loads used in this study had no significant effect on either the right or the left side of the erector spinae muscle at this frequency, suggesting that a higher amount and percentage of loads would produce more substantial results in the study of isotonic contractions.

An investigation of pile diameter influence in the bearing capacity on Dynamic Load Test (DLT)

During the construction of five residential buildings in the city of Taubate, State of São Paulo, it was possible to carry out one comprehensive investigation of the behavior of precast concrete piles in clay shales. This paper describes the results of Dynamic Load Tests (DLT's) executed in three piles with different diameters and with the same embedded length. The tests were monitored using the PDA(R) (Pile Driving Analyzer) and the pile top displacement was measured by pencil and paper procedure. From the curves of RMX versus DMX resulted from CASE(R) method, CAPWAPC(R) analyses were made for signals where the maximum mobilized soil resistance was verified. The results were compared with the predicted bearing capacity using the semi-empirical method of Decourt & Quaresma (1978) and Decourt (1982) based on SPT values and the description of the soil profile. Some comments related to the values of quake and damping used for clay shales in the analyses are also presented.

Experience gained and difficulties in performing dynamic load test in composite piles made with steel rails

The results of dynamic instrumentation in two construction sites that used steel rails as pile foundation are presented in this paper. The first dynamic load tests were executed in piles made by single steel rails of the type TR32 and TR37. In the second group of dynamic tests, the piles were made by a composition of two and three steel rails of the same type TR37. The difficulties in placing the sensors, the effect of hammer blow eccentricity and the influence of the non-uniform welding along the pile length are presented in detail and discussed.