Inorganic surface passivation of PbS nanocrystals resulting in strong photoluminescent emission

Strong photoluminescent emission has been obtained from 3 nm PbS nanocrystals in aqueous colloidal solution, following treatment with CdS precursors. The observed emission can extend across the entire visible spectrum and usually includes a peak near 1.95 eV. We show that much of the visible emission results from absorption by higher-lying excited states above 3.0 eV with subsequent relaxation to and emission from states lying above the observed band-edge of the PbS nanocrystals. The fluorescent lifetimes for this emission are in the nanosecond regime, characteristic of exciton recombination.

Investigation of the role of cadmium sulfide in the surface passivation of lead sulfide quantum dots

Surface passivation of PbS nanocrystals (NC), resulting in strong photoluminescence, can be achieved by the introduction of CdS precursors. The role of CdS in the surface passivation of PbS NCs is uncertain, as the crystalline structure of CdS and PbS are different, which should impede effective epitaxial overgrowth. Absorption spectroscopy is used to show that the CdS precursors strongly interact with the PbS NC surface. Electron microscopy reveals that the introduction of CdS precursors results in an increased particle size, consistent with overcoating. However, we also find the process to be highly non-uniform. Nevertheless, evidence for epitaxial growth is found, suggesting that effective surface passivation may be possible.

Surface passivation of crystalline silicon by Cat-CVD amorphous and nanocrystalline thin silicon films

In this work, we study the electronic surface passivation of crystalline silicon with intrinsic thin silicon films deposited by Catalytic CVD. The contactless method used to determine the effective surface recombination velocity was the quasi-steady-state photoconductance technique. Hydrogenated amorphous and nanocrystalline silicon films were evaluated as passivating layers on n- and p-type float zone silicon wafers. The best results were obtained with amorphous silicon films, which allowed effective surface recombination velocities as low as 60 and 130 cms -1 on p- and n-type silicon, respectively. To our knowledge, these are the best results ever reported with intrinsic amorphous silicon films deposited by Catalytic CVD. The passivating properties of nanocrystalline silicon films strongly depended on the deposition conditions, especially on the filament temperature. Samples grown at lower filament temperatures (1600 °C) allowed effective surface recombination velocities of 450 and 600 cms -1 on n- and p-type silicon.

Surface passivation and optical characterization of Al2O3/a-SiCx stacks on c-Si substrates

Postprint (published version)

Surface Passivation of Nanoporous TiO2 via Atomic Layer Deposition of ZrO2 for Solid-State Dye-Sensitized Solar Cell Applications

We report here the utilization of atomid layer deposition to passivate surface map states in mosoporous TiO2 nanoparticles for solid state dye sensitized solar cells based on 9,9'-spirobifluorene (spiro-OMeTAD). By depositing ZrO2 films with angstrom-level precision, coating the mesoporous TiO2 produces over a two-fold enhancement in short-circuit current density, as compared to a control device. Impedance spectroscopy measurements provide evidence that the ZrO2 coating reduces recombination lossed at the TiO2/spiro-OMeTAD interface and passivates localized surface states. Low-frequency negative capacitances, frequently observed in nanocomposite solar cells, have been associated with the surface-state mediated charge transfer from TiO2 to the spiro-OMeTAD.

Polarized photoluminescence from surface-passivated lead sulfide nanocrystals

Effective surface passivation of lead sulfide (PbS) nanocrystals (NCs) in an aqueous colloidal solution has been achieved following treatment with CdS precursors. The resultant photoluminescent emission displays two distinct components, one originating from the absorption band edge and the other from above the absorption band edge. We show that both of these components are strongly polarized but display distinctly different behaviours. The polarization arising from the band edge shows little dependence on the excitation energy while the polarization of the above-band-edge component is strongly dependent on the excitation energy. In addition, time-resolved polarization spectroscopy reveals that the above-band-edge polarization is restricted to the first couple of nanoseconds, while the band edge polarization is nearly constant over hundreds of nanoseconds. We recognize an incompatibility between the two different polarization behaviours, which enables us to identify two distinct types of surface-passivated PbS NC.

Surface InGaAs nanostructures for sensing applications

El desarrollo de sensores está ganando cada vez mayor importancia debido a la concienciación ciudadana sobre el medio ambiente haciendo que su desarrollo sea muy elevado en todas las disciplinas, entre las que cabe destacar, la medicina, la biología y la química. A pesar de la existencia de estos dispositivos, este área está aún por mejorar, ya que muchos de los materiales propuestos hasta el momento e incluso los ya comercializados muestran importantes carencias de funcionamiento, eficiencia e integrabilidad entre otros. Para la mejora de estos dispositivos, se han propuesto diversas aproximaciones basadas en nanosistemas. Quizá, uno de las más prometedoras son las nanoestructuras de punto cuántico, y en particular los semiconductores III-V basados en la consolidada tecnología de los arseniuros, las cuáles ofrecen excelentes propiedades para su uso como sensores. Además, estudios recientes demuestran su gran carácter sensitivo al medio ambiente, la posibilidad de funcionalizar la superficie para la fabricación de sensores interdisciplinares y posibilididad de mejorar notablemente su eficiencia. A lo largo de esta tesis, nos centramos en la investigación de SQD de In0.5Ga0.5As sobre substratos de GaAs(001) para el desarrollo de sensores de humedad. La tesis abarca desde el diseño, crecimiento y caracterización de las muestras hasta la el posterior procesado y caracterización de los dispositivos finales. La optimización de los parámetros de crecimiento es fundamental para conseguir una nanoestructura con las propiedades operacionales idóneas para un fin determinado. Como es bien sabido en la literatura, los parámetros de crecimiento (temperatura de crecimiento, relación de flujos del elemento del grupo V y del grupo I II (V/III), velocidad de crecimiento y tratamiento térmico después de la formación de la capa activa) afectan directamente a las propiedades estructurales, y por tanto, operacionales de los puntos cuánticos (QD). En esta tesis, se realiza un estudio de las condiciones de crecimiento para el uso de In0.5Ga0.5As SQDs como sensores. Para los parámetros relacionados con la temperatura de crecimiento de los QDs y la relación de flujos V / I I I se utilizan los estudios previamente realizados por el grupo. Mientras que este estudio se centrará en la importancia de la velocidad de crecimiento y en el tratamiento térmico justo después de la nucleación de los QDs. Para ello, se establece la temperatura de creciemiento de los QDs en 430°C y la relación de flujos V/III en 20. Como resultado, los valores más adecuados que se obtienen para la velocidad de crecimiento y el tratamiento térmico posterior a la formación de los puntos son, respectivamente, 0.07ML/s y la realización de una bajada y subida brusca de la temperatura del substrato de 100°C con respecto a la temperatura de crecimiento de los QDs. El crecimiento a una velocidad lo suficientemente alta que permita la migración de los átomos por la superficie, pero a su vez lo suficientemente baja para que se lleve a cabo la nucleación de los QDs; en combinación con el tratamiento brusco de temperatura que hace que se conserve la forma y composición de los QDs, da lugar a unos SQDs con un alto grado de homogeneidad y alta densidad superficial. Además, la caracterización posterior indica que estas nanoestructuras de gran calidad cristalina presentan unas propiedades ópticas excelentes incluso a temperatura ambiente. Una de las características por la cual los SQD de Ino.5Gao.5As se consideran candidatos prometedores para el desarrollo de sensores es el papel decisivo que juega la superficie por el mero hecho de estar en contacto directo con las partículas del ambiente y, por tanto, por ser capaces de interactuar con sus moléculas. Así pues, con el fin de demostrar la idoneidad de este sistema para dicha finalidad, se evalúa el impacto ambiental en las propiedades ópticas y eléctricas de las muestras. En un primer lugar, se analiza el efecto que tiene el medio en las propiedades ópticas. Para dicha evaluación se compara la variación de las propiedades de emisión de una capa de puntos enterrada y una superficial en distintas condiciones externas. El resultado que se obtiene es muy claro, los puntos enterrados no experimentan un cambio óptico apreciable cuando se varían las condiciones del entorno; mientras que, la emisión de los SQDs se modifica significativamente con las condiciones del medio. Por una parte, la intensidad de emisión de los puntos superficiales desaparece en condiciones de vacío y decrece notablemente en atmósferas secas de gases puros (N2, O2). Por otra parte, la fotoluminiscencia se conserva en ambientes húmedos. Adicionalmente, se observa que la anchura a media altura y la longitud de onda de emisión no se ven afectadas por los cambios en el medio, lo que indica, que las propiedades estructurales de los puntos se conservan al variar la atmósfera. Estos resultados apuntan directamente a los procesos que tienen lugar en la superficie entre estados confinados y superficiales como responsables principales de este comportamiento. Así mismo, se ha llevado a cabo un análisis más detallado de la influencia de la calidad y composición de la atmósfera en las propiedades ópticas de los puntos cuánticos superficiales. Para ello, se utilizan distintas sustancias con diferente polaridad, composición atómica y masa molecular. Como resultado se observa que las moléculas de menor polaridad y más pesadas causan una mayor variación en la intensidad de emisión. Además, se demuestra que el oxígeno juega un papel decisivo en las propiedades ópticas. En presencia de moléculas que contienen oxígeno, la intensidad de fotoluminiscencia disminuye menos que en atmósferas constituidas por especies que no contienen oxígeno. Las emisión que se observa respecto a la señal en aire es del 90% y del 77%, respectivamente, en atmósferas con presencia o ausencia de moléculas de oxígeno. El deterioro de la señal de emisión se atribuye a la presencia de defectos, enlaces insaturados y, en general, estados localizados en la superficie. Estos estados actúan como centros de recombinación no radiativa y, consecuentemente, se produce un empeoramiento de las propiedades ópticas de los SQDs. Por tanto, la eliminación o reducción de la densidad de estos estados superficiales haría posible una mejora de la intensidad de emisión. De estos experimentos de fotoluminiscencia, se deduce que las interacciones entre las moléculas presentes en la atmósfera y la superficie de la muestra modifican la superficie. Esta alteración superficial se traduce en un cambio significativo en las propiedades de emisión. Este comportamiento se atribuye a la posible adsorción de moléculas sobre la superficie pasivando los centros no radiativos, y como consecuencia, mejorando las propiedades ópticas. Además, los resultados demuestran que las moléculas que contienen oxígeno con mayor polaridad y más ligeras son adsorbidas con mayor facilidad, lo que hace que la intensidad óptica sufra variaciones despreciables con respecto a la emisión en aire. Con el fin de desarrollar sensores, las muestras se procesan y los dispositivos se caracterizan eléctricamente. El procesado consiste en dos contactos cuadrados de una aleación de Ti/Au. Durante el procesado, lo más importante a tener en cuenta es no realizar ningún ataque o limpieza que pueda dañar la superficie y deteriorar las propiedades de las nanostructuras. En este apartado, se realiza un análisis completo de una serie de tres muestras: GaAs (bulk), un pozo cuántico superficial (SQW) de Ino.5Gao.5As y SQDs de Ino.5Gao.5As. Para ello, a cada una de las muestras se le realizan medidas de I-V en distintas condiciones ambientales. En primer lugar, siguiendo los resultados obtenidos ópticamente, se lleva a cabo una comparación de la respuesta eléctrica en vacío y aire. A pesar de que todas las muestras presentan un carácter más resistivo en vacío que en aire, se observa una mayor influencia sobre la muestra de SQD. En vacío, la resistencia de los SQDs decrece un 99% respecto de su valor en aire, mientras que la variación de la muestras de GaAs e Ino.5Gao.5As SQW muestran una reducción, respectivamente, del 31% y del 20%. En segundo lugar, se realiza una evaluación aproximada del posible efecto de la humedad en la resistencia superficial de las muestras mediante la exhalación humana. Como resultado se obtiene, que tras la exhalación, la resistencia disminuye bruscamente y recupera su valor inicial cuando dicho proceso concluye. Este resultado preliminar indica que la humedad es un factor crítico en las propiedades eléctricas de los puntos cuánticos superficiales. Para la determinación del papel de la humedad en la respuesta eléctrica, se somete a las muestras de SQD y SQW a ambientes con humedad relativa (RH, de la siglas del inglés) controlada y se analiza el efecto sobre la conductividad superficial. Tras la variación de la RH desde 0% hasta el 70%, se observa que la muestra SQW no cambia su comportamiento eléctrico al variar la humedad del ambiente. Sin embargo, la respuesta de la muestra SQD define dos regiones bien diferenciadas, una de alta sensibilidad para valores por debajo del 50% de RH, en la que la resistencia disminuye hasta en un orden de magnitud y otra, de baja sensibilidad (>50%), donde el cambio de la resistencia es menor. Este resultado resalta la especial relevancia no sólo de la composición sino también de la morfología de la nanostructura superficial en el carácter sensitivo de la muestra. Por último, se analiza la influencia de la iluminación en la sensibilidad de la muestra. Nuevamente, se somete a las muestras SQD y SQW a una irradiación de luz de distinta energía y potencia a la vez que se varía controladamente la humedad ambiental. Una vez más, se observa que la muestra SQW no presenta ninguna variación apreciable con las alteraciones del entorno. Su resistencia superficial permanece prácticamente inalterable tanto al modificar la potencia de la luz incidente como al variar la energía de la irradiación. Por el contrario, en la muestra de SQD se obtiene una reducción la resistencia superficial de un orden de magnitud al pasar de condiciones de oscuridad a iluminación. Con respecto a la potencia y energía de la luz incidente, se observa que a pesar de que la muestra no experimenta variaciones notables con la potencia de la irradiación, esta sufre cambios significativos con la energía de la luz incidente. Cuando se ilumina con energías por encima de la energía de la banda prohibida (gap) del GaAs (Eg ~1.42 eV ) se produce una reducción de la resistencia de un orden de magnitud en atmósferas húmedas, mientras que en atmósferas secas la conductividad superficial permanece prácticamente constante. Sin embargo, al inicidir con luz de energía menor que Eg, el efecto que se produce en la respuesta eléctrica es despreciable. Esto se atribuye principalmente a la densidad de portadores fotoactivados durante la irradiación. El volumen de portadores excita dos depende de la energía de la luz incidente. De este modo, cuando la luz que incide tiene energía menor que el gap, el volumen de portadores generados es pequeño y no contribuye a la conductividad superficial. Por el contrario, cuando la energía de la luz incidente es alta (Eg), el volumen de portadores activados es elevado y éstos contribuyen significantemente a la conductividad superficial. La combinación de ambos agentes, luz y humedad, favorece el proceso de adsorción de moléculas y, por tanto, contribuye a la reducción de la densidad de estados superficiales, dando lugar a una modificación de la estructura electrónica y consecuentemente favoreciendo o dificultando el transporte de portadores. ABSTRACT Uncapped three-dimensional (3D) nanostructures have been generally grown to assess their structural quality. However, the tremendous growing importance of the impact of the environment on life has become such nanosystems in very promising candidates for the development of sensing devices. Their direct exposure to changes in the local surrounding may influence their physical properties being a perfect sign of the atmosphere quality. The goal of this thesis is the research of Ino.5Gao.5As surface quantum dots (SQDs) on GaAs(001), covering from their growth to device fabrication, for sensing applications. The achievement of this goal relies on the design, growth and sample characterization, along with device fabrication and characterization. The first issue of the thesis is devoted to analyze the main growth parameters affecting the physical properties of the Ino.5Gao.5As SQDs. It is well known that the growing conditions (growth temperature , deposition rate, V/III flux ratio and treatment after active layer growth) directly affect the physical properties of the epilayer. In this part, taking advantage of the previous results in the group regarding Ino.5Gao.5As QD growth temperature and V/III ratio, the effect of the growth rate and the temperature treatment after QDs growth nucleation is evaluated. Setting the QDs growth temperature at 430°C and the V/III flux ratio to ~20, it is found that the most appropriate conditions rely on growing the QDs at 0.07ML/s and just after QD nucleation, rapidly dropping and again raising 100°C the substrate temperature with respect to the temperature of QD growth. The combination of growing at a fast enough growth rate to promote molecule migration but sufficiently slow to allow QD nucleation, together with the sharp variation of the temperature preserving their shape and composition yield to high density, homogeneous Ino.5Gao.5As SQDs. Besides, it is also demonstrated that this high quality SQDs show excellent optical properties even at room temperature (RT). One of the characteristics by which In0.5Ga0.5As/GaAs SQDs are considered promising candidates for sensing applications is the crucial role that surface plays when interacting with the gases constituting the atmosphere. Therefore, in an attempt to develop sensing devices, the influence of the environment on the physical properties of the samples is evaluated. By comparing the resulting photoluminescence (PL) of SQDs with buried QDs (BQDs), it is found that BQDs do not exhibit any significant variation when changing the environmental conditions whereas, the external conditions greatly act on the SQDs optical properties. On one hand, it is evidenced that PL intensity of SQDs sharply quenches under vacuum and clearly decreases under dry-pure gases atmospheres (N2, O2). On the other hand, it is shown that, in water containing atmospheres, the SQDs PL intensity is maintained with respect to that in air. Moreover, it is found that neither the full width at half maximun nor the emission wavelength manifest any noticeable change indicating that the QDs are not structurally altered by the external atmosphere. These results decisively point to the processes taking place at the surface such as coupling between confined and surface states, to be responsible of this extraordinary behavior. A further analysis of the impact of the atmosphere composition on the optical characteristics is conducted. A sample containing one uncapped In0.5Ga0.5As QDs layer is exposed to different environments. Several solvents presenting different polarity, atomic composition and molecular mass, are used to change the atmosphere composition. It is revealed that low polarity and heavy molecules cause a greater variation on the PL intensity. Besides, oxygen is demonstrated to play a decisive role on the PL response. Results indicate that in presence of oxygen-containing molecules, the PL intensity experiments a less reduction than that suffered in presence of nonoxygen-containing molecules, 90% compared to 77% signal respect to the emission in air. In agreement with these results, it is demonstrated that high polarity and lighter molecules containing oxygen are more easily adsorbed, and consequently, PL intensity is less affected. The presence of defects, unsaturated bonds and in general localized states in the surface are proposed to act as nonradiative recombination centers deteriorating the PL emission of the sample. Therefore, suppression or reduction of the density of such states may lead to an increase or, at least, conservation of the PL signal. This research denotes that the interaction between sample surface and molecules in the atmosphere modifies the surface characteristics altering thus the optical properties. This is attributed to the likely adsoption of some molecules onto the surface passivating the nonradiative recombination centers, and consequently, not deteriorating the PL emission. Aiming for sensors development, samples are processed and electrically characterized under different external conditions. Samples are processed with two square (Ti/Au) contacts. During the processing, especial attention must be paid to the surface treatment. Any process that may damage the surface such as plasma etching or annealing must be avoided to preserve the features of the surface nanostructures. A set of three samples: a GaAs (bulk), In0.5Ga0.5As SQDs and In0.5Ga0.5As surface quantum well (SQW) are subjected to a throughout evaluation. I-V characteristics are measured following the results from the optical characterization. Firstly, the three samples are exposed to vacuum and air. Despite the three samples exhibit a more resistive character in vacuum than in air, it is revealed a much more clear influence of the pressure atmosphere in the SQDs sample. The sheet resistance (Rsh) of SQDs decreases a 99% from its response value under vacuum to its value in air, whereas Rsh of GaAs and In0.5Ga0.5As SQW reduces its value a 31% and a 20%, respectively. Secondly, a rough analysis of the effect of the human breath on the electrical response evidences the enormous influence of moisture (human breath is composed by several components but the one that overwhelms all the rest is the high concentration of water vapor) on the I-V characteristics. Following this result, In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW are subjected to different controlled relative humidity (RH) environments (from 0% to 70%) and electrically characterized. It is found that SQW shows a nearly negligible Rsh variation when increasing the RH in the surroundings. However, the response of SQDs to changes in the RH defines two regions. Below 50%, high sensitive zone, Rsh of SQD decreases by more than one order of magnitude, while above 50% the dependence of Rsh on the RH becomes weaker. These results remark the role of the surface and denote the existence of a finite number of surface states. Nevertheless, most significantly, they highlight the importance not only of the material but also of the morphology. Finally, the impact of the illumination is determined by means of irradiating the In0.5Ga0.5As SQDs and In0.5Ga0.5As SQW samples with different energy and power sources. Once again, SQW does not exhibit any correlation between the surface conductivity and the external conditions. Rsh remains nearly unalterable independently of the energy and power of the incident light. Conversely, Rsh of SQD experiences a decay of one order of magnitude from dark-to-photo conditions. This is attributed to the less density of surface states of SQW compared to that of SQDs. Additionally, a different response of Rsh of SQD with the energy of the impinging light is found. Illuminating with high energy light results in a Rsh reduction of one order of mag nitude under humid atmospheres, whereas it remains nearly unchanged under dry environments. On the contrary, light with energy below the bulk energy bandgap (Eg), shows a negligible effect on the electrical properties regardless the local moisture. This is related to the density of photocarriers generated while lighting up. Illuminating with excitation energy below Eg affects a small absorption volume and thus, a low density of photocarriers may be activated leading to an insignificant contribution to the conductivity. Nonetheless, irradiating with energy above the Eg can excite a high density of photocarriers and greatly improve the surface conductivity. These results demonstrate that both illumination and humidity are therefore needed for sensing. The combination of these two agents improves the surface passivation by means of molecule adsorption reducing the density of surface states, thus modifying the electronic structures, and consequently, promoting the carrier motion.

Structural and optical analysis of GaAsP/GaP core-shell nanowires

The structural and optical properties of GaAsP/GaP core-shell nanowires grown by gas source molecular beam epitaxy were investigated by transmission electron microscopy, Raman spectroscopy, photoluminescence (PL), and magneto-PL. The effects of surface depletion and compositional variations in the ternary alloy manifested as a redshift in GaAsP PL upon surface passivation, and a decrease in redshift in PL in the presence of a magnetic field due to spatial confinement of carriers.

Eeny meeny miny moe, catch a transcript by the toe, or how to enumerate eukaryotic transcripts.

In this issue of Genes & Development, Revyakin and colleagues (pp. 1691-1702) measure the relation between individual RNA polymerase II transcription events and transcription factor assembly by counting RNA transcripts retained on the template DNA using single-molecule fluorescence.

The effects of electron-hole separation on the photoconductivity of individual metal oxide nanowires

The responses of individual ZnO nanowires to UV light demonstrate that the persistent photoconductivity (PPC) state is directly related to the electron¿hole separation near the surface. Our results demonstrate that the electrical transport in these nanomaterials is influenced by the surface in two different ways. On the one hand, the effective mobility and the density of free carriers are determined by recombination mechanisms assisted by the oxidizing molecules in air. This phenomenon can also be blocked by surface passivation. On the other hand, the surface built-in potential separates the photogenerated electron¿hole pairs and accumulates holes at the surface. After illumination, the charge separation makes the electron¿hole recombination difficult and originates PPC. This effect is quickly reverted after increasing either the probing current (self-heating by Joule dissipation) or the oxygen content in air (favouring the surface recombination mechanisms). The model for PPC in individual nanowires presented here illustrates the intrinsic potential of metal oxide nanowires to develop optoelectronic devices or optochemical sensors with better and new performances.

Roll-to-roll atomic layer deposition process for flexible electronics applications

Atomic Layer Deposition (ALD) is the technology of choice where very thin and highquality films are required. Its advantage is its ability to deposit dense and pinhole-free coatings in a controllable manner. It has already shown promising results in a range of applications, e.g. diffusion barrier coatings for OLED displays, surface passivation layers for solar panels. Spatial Atomic Layer Deposition (SALD) is a concept that allows a dramatic increase in ALD throughput. During the SALD process, the substrate moves between spatially separated zones filled with the respective precursor gases and reagents in such a manner that the exposure sequence replicates the conventional ALD cycle. The present work describes the development of a high-throughput ALD process. Preliminary process studies were made using an SALD reactor designed especially for this purpose. The basic properties of the ALD process were demonstrated using the wellstudied Al2O3 trimethyl aluminium (TMA)+H2O process. It was shown that the SALD reactor is able to deposit uniform films in true ALD mode. The ALD nature of the process was proven by demonstrating self-limiting behaviour and linear film growth. The process behaviour and properties of synthesized films were in good agreement with previous ALD studies. Issues related to anomalous deposition at low temperatures were addressed as well. The quality of the coatings was demonstrated by applying 20 nm of the Al2O3 on to polymer substrate and measuring its moisture barrier properties. The results of tests confirmed the superior properties of the coatings and their suitability for flexible electronics encapsulation. Successful results led to the development of a pilot scale roll-to-roll coating system. It was demonstrated that the system is able to deposit superior quality films with a water transmission rate of 5x10-6 g/m2day at a web speed of 0.25 m/min. That is equivalent to a production rate of 180 m2/day and can be potentially increased by using wider webs. State-of-art film quality, high production rates and repeatable results make SALD the technology of choice for manufacturing ultra-high barrier coatings for flexible electronics.

Probing the functionalization of gold surfaces and protein adsorption by PM-IRRAS

The control of morphology and coating of metal surfaces is essential for a number of organic electronic devices including photovoltaic cells and sensors. In this study, we monitor the functionalization of gold surfaces with 11-mercaptoundecanoic acid (MUA, HS(CH(2))(10)CO(2)H) and cysteamine, aiming at passivating the surfaces for application in surface plasmon resonance (SPR) biosensors. Using polarization-modulated infrared reflection-absorption spectroscopy (PM-IRRAS), cyclic voltammetry, atomic force microscopy and quartz crystal microbalance, we observed a time-dependent organization process of the adsorbed MUA monolayer with alkyl chains perpendicular to the gold surface. Such optimized condition for surface passivation was obtained with a systematic search for experimental parameters leading to the lowest electrochemical signal of the functionalized gold electrode. The ability to build supramolecular architectures was also confirmed by detecting with PM-IRRAS the adsorption of streptavidin on the MUA-functionalized gold. As the approaches used for surface functionalization and its verification with PM-IRRAS are generic, one may now envisage monitoring the fabrication of tailored electrodes for a variety of applications.

Field dependent transition to the non-linear regime in magnetic hyperthermia experiments: Comparison between maghemite, copper, zinc, nickel and cobalt ferrite nanoparticles of similar sizes

Further advances in magnetic hyperthermia might be limited by biological constraints, such as using sufficiently low frequencies and low field amplitudes to inhibit harmful eddy currents inside the patient's body. These incite the need to optimize the heating efficiency of the nanoparticles, referred to as the specific absorption rate (SAR). Among the several properties currently under research, one of particular importance is the transition from the linear to the non-linear regime that takes place as the field amplitude is increased, an aspect where the magnetic anisotropy is expected to play a fundamental role. In this paper we investigate the heating properties of cobalt ferrite and maghemite nanoparticles under the influence of a 500 kHz sinusoidal magnetic field with varying amplitude, up to 134 Oe. The particles were characterized by TEM, XRD, FMR and VSM, from which most relevant morphological, structural and magnetic properties were inferred. Both materials have similar size distributions and saturation magnetization, but strikingly different magnetic anisotropies. From magnetic hyperthermia experiments we found that, while at low fields maghemite is the best nanomaterial for hyperthermia applications, above a critical field, close to the transition from the linear to the non-linear regime, cobalt ferrite becomes more efficient. The results were also analyzed with respect to the energy conversion efficiency and compared with dynamic hysteresis simulations. Additional analysis with nickel, zinc and copper-ferrite nanoparticles of similar sizes confirmed the importance of the magnetic anisotropy and the damping factor. Further, the analysis of the characterization parameters suggested core-shell nanostructures, probably due to a surface passivation process during the nanoparticle synthesis. Finally, we discussed the effect of particle-particle interactions and its consequences, in particular regarding discrepancies between estimated parameters and expected theoretical predictions. Copyright 2012 Author(s). This article is distributed under a Creative Commons Attribution 3.0 Unported License. [http://dx.doi. org/10.1063/1.4739533]

MOVPE growth of III-V semiconductors on silicon for third generation solar cells

Esta Tesis trata sobre el desarrollo y crecimiento -mediante tecnología MOVPE (del inglés: MetalOrganic Vapor Phase Epitaxy)- de células solares híbridas de semiconductores III-V sobre substratos de silicio. Esta integración pretende ofrecer una alternativa a las células actuales de III-V, que, si bien ostentan el récord de eficiencia en dispositivos fotovoltaicos, su coste es, a día de hoy, demasiado elevado para ser económicamente competitivo frente a las células convencionales de silicio. De este modo, este proyecto trata de conjugar el potencial de alta eficiencia ya demostrado por los semiconductores III-V en arquitecturas de células fotovoltaicas multiunión con el bajo coste, la disponibilidad y la abundancia del silicio. La integración de semiconductores III-V sobre substratos de silicio puede afrontarse a través de diferentes aproximaciones. En esta Tesis se ha optado por el desarrollo de células solares metamórficas de doble unión de GaAsP/Si. Mediante esta técnica, la transición entre los parámetros de red de ambos materiales se consigue por medio de la formación de defectos cristalográficos (mayoritariamente dislocaciones). La idea es confinar estos defectos durante el crecimiento de sucesivas capas graduales en composición para que la superficie final tenga, por un lado, una buena calidad estructural, y por otro, un parámetro de red adecuado. Numerosos grupos de investigación han dirigido sus esfuerzos en los últimos años en desarrollar una estructura similar a la que aquí proponemos. La mayoría de éstos se han centrado en entender los retos asociados al crecimiento de materiales III-V, con el fin de conseguir un material de alta calidad cristalográfica. Sin embargo, prácticamente ninguno de estos grupos ha prestado especial atención al desarrollo y optimización de la célula inferior de silicio, cuyo papel va a ser de gran relevancia en el funcionamiento de la célula completa. De esta forma, y con el fin de completar el trabajo hecho hasta el momento en el desarrollo de células de III-V sobre silicio, la presente Tesis se centra, fundamentalmente, en el diseño y optimización de la célula inferior de silicio, para extraer su máximo potencial. Este trabajo se ha estructurado en seis capítulos, ordenados de acuerdo al desarrollo natural de la célula inferior. Tras un capítulo de introducción al crecimiento de semiconductores III-V sobre Si, en el que se describen las diferentes alternativas para su integración; nos ocupamos de la parte experimental, comenzando con una extensa descripción y caracterización de los substratos de silicio. De este modo, en el Capítulo 2 se analizan con exhaustividad los diferentes tratamientos (tanto químicos como térmicos) que deben seguir éstos para garantizar una superficie óptima sobre la que crecer epitaxialmente el resto de la estructura. Ya centrados en el diseño de la célula inferior, el Capítulo 3 aborda la formación de la unión p-n. En primer lugar se analiza qué configuración de emisor (en términos de dopaje y espesor) es la más adecuada para sacar el máximo rendimiento de la célula inferior. En este primer estudio se compara entre las diferentes alternativas existentes para la creación del emisor, evaluando las ventajas e inconvenientes que cada aproximación ofrece frente al resto. Tras ello, se presenta un modelo teórico capaz de simular el proceso de difusión de fosforo en silicio en un entorno MOVPE por medio del software Silvaco. Mediante este modelo teórico podemos determinar qué condiciones experimentales son necesarias para conseguir un emisor con el diseño seleccionado. Finalmente, estos modelos serán validados y constatados experimentalmente mediante la caracterización por técnicas analíticas (i.e. ECV o SIMS) de uniones p-n con emisores difundidos. Uno de los principales problemas asociados a la formación del emisor por difusión de fósforo, es la degradación superficial del substrato como consecuencia de su exposición a grandes concentraciones de fosfina (fuente de fósforo). En efecto, la rugosidad del silicio debe ser minuciosamente controlada, puesto que éste servirá de base para el posterior crecimiento epitaxial y por tanto debe presentar una superficie prístina para evitar una degradación morfológica y cristalográfica de las capas superiores. En este sentido, el Capítulo 4 incluye un análisis exhaustivo sobre la degradación morfológica de los substratos de silicio durante la formación del emisor. Además, se proponen diferentes alternativas para la recuperación de la superficie con el fin de conseguir rugosidades sub-nanométricas, que no comprometan la calidad del crecimiento epitaxial. Finalmente, a través de desarrollos teóricos, se establecerá una correlación entre la degradación morfológica (observada experimentalmente) con el perfil de difusión del fósforo en el silicio y por tanto, con las características del emisor. Una vez concluida la formación de la unión p-n propiamente dicha, se abordan los problemas relacionados con el crecimiento de la capa de nucleación de GaP. Por un lado, esta capa será la encargada de pasivar la subcélula de silicio, por lo que su crecimiento debe ser regular y homogéneo para que la superficie de silicio quede totalmente pasivada, de tal forma que la velocidad de recombinación superficial en la interfaz GaP/Si sea mínima. Por otro lado, su crecimiento debe ser tal que minimice la aparición de los defectos típicos de una heteroepitaxia de una capa polar sobre un substrato no polar -denominados dominios de antifase-. En el Capítulo 5 se exploran diferentes rutinas de nucleación, dentro del gran abanico de posibilidades existentes, para conseguir una capa de GaP con una buena calidad morfológica y estructural, que será analizada mediante diversas técnicas de caracterización microscópicas. La última parte de esta Tesis está dedicada al estudio de las propiedades fotovoltaicas de la célula inferior. En ella se analiza la evolución de los tiempos de vida de portadores minoritarios de la base durante dos etapas claves en el desarrollo de la estructura Ill-V/Si: la formación de la célula inferior y el crecimiento de las capas III-V. Este estudio se ha llevado a cabo en colaboración con la Universidad de Ohio, que cuentan con una gran experiencia en el crecimiento de materiales III-V sobre silicio. Esta tesis concluye destacando las conclusiones globales del trabajo realizado y proponiendo diversas líneas de trabajo a emprender en el futuro. ABSTRACT This thesis pursues the development and growth of hybrid solar cells -through Metal Organic Vapor Phase Epitaxy (MOVPE)- formed by III-V semiconductors on silicon substrates. This integration aims to provide an alternative to current III-V cells, which, despite hold the efficiency record for photovoltaic devices, their cost is, today, too high to be economically competitive to conventional silicon cells. Accordingly, the target of this project is to link the already demonstrated efficiency potential of III-V semiconductor multijunction solar cell architectures with the low cost and unconstrained availability of silicon substrates. Within the existing alternatives for the integration of III-V semiconductors on silicon substrates, this thesis is based on the metamorphic approach for the development of GaAsP/Si dual-junction solar cells. In this approach, the accommodation of the lattice mismatch is handle through the appearance of crystallographic defects (namely dislocations), which will be confined through the incorporation of a graded buffer layer. The resulting surface will have, on the one hand a good structural quality; and on the other hand the desired lattice parameter. Different research groups have been working in the last years in a structure similar to the one here described, being most of their efforts directed towards the optimization of the heteroepitaxial growth of III-V compounds on Si, with the primary goal of minimizing the appearance of crystal defects. However, none of these groups has paid much attention to the development and optimization of the bottom silicon cell, which, indeed, will play an important role on the overall solar cell performance. In this respect, the idea of this thesis is to complete the work done so far in this field by focusing on the design and optimization of the bottom silicon cell, to harness its efficiency. This work is divided into six chapters, organized according to the natural progress of the bottom cell development. After a brief introduction to the growth of III-V semiconductors on Si substrates, pointing out the different alternatives for their integration; we move to the experimental part, which is initiated by an extensive description and characterization of silicon substrates -the base of the III-V structure-. In this chapter, a comprehensive analysis of the different treatments (chemical and thermal) required for preparing silicon surfaces for subsequent epitaxial growth is presented. Next step on the development of the bottom cell is the formation of the p-n junction itself, which is faced in Chapter 3. Firstly, the optimization of the emitter configuration (in terms of doping and thickness) is handling by analytic models. This study includes a comparison between the different alternatives for the emitter formation, evaluating the advantages and disadvantages of each approach. After the theoretical design of the emitter, it is defined (through the modeling of the P-in-Si diffusion process) a practical parameter space for the experimental implementation of this emitter configuration. The characterization of these emitters through different analytical tools (i.e. ECV or SIMS) will validate and provide experimental support for the theoretical models. A side effect of the formation of the emitter by P diffusion is the roughening of the Si surface. Accordingly, once the p-n junction is formed, it is necessary to ensure that the Si surface is smooth enough and clean for subsequent phases. Indeed, the roughness of the Si must be carefully controlled since it will be the basis for the epitaxial growth. Accordingly, after quantifying (experimentally and by theoretical models) the impact of the phosphorus on the silicon surface morphology, different alternatives for the recovery of the surface are proposed in order to achieve a sub-nanometer roughness which does not endanger the quality of the incoming III-V layers. Moving a step further in the development of the Ill-V/Si structure implies to address the challenges associated to the GaP on Si nucleation. On the one hand, this layer will provide surface passivation to the emitter. In this sense, the growth of the III-V layer must be homogeneous and continuous so the Si emitter gets fully passivated, providing a minimal surface recombination velocity at the interface. On the other hand, the growth should be such that the appearance of typical defects related to the growth of a polar layer on a non-polar substrate is minimized. Chapter 5 includes an exhaustive study of the GaP on Si nucleation process, exploring different nucleation routines for achieving a high morphological and structural quality, which will be characterized by means of different microscopy techniques. Finally, an extensive study of the photovoltaic properties of the bottom cell and its evolution during key phases in the fabrication of a MOCVD-grown III-V-on-Si epitaxial structure (i.e. the formation of the bottom cell; and the growth of III-V layers) will be presented in the last part of this thesis. This study was conducted in collaboration with The Ohio State University, who has extensive experience in the growth of III-V materials on silicon. This thesis concludes by highlighting the overall conclusions of the presented work and proposing different lines of work to be undertaken in the future.

Investigação do mecanismo cinético da reação de redução de oxigênio em solventes não aquosos

O aumento no consumo energético e a crescente preocupação ambiental frente à emissão de gases poluentes criam um apelo mundial favorável para pesquisas de novas tecnologias não poluentes de fontes de energia. Baterias recarregáveis de lítio-ar em solventes não aquosos possuem uma alta densidade de energia teórica (5200 Wh kg-1), o que as tornam promissoras para aplicação em dispositivos estacionários e em veículos elétricos. Entretanto, muitos problemas relacionados ao cátodo necessitam ser contornados para permitir a aplicação desta tecnologia, por exemplo, a baixa reversibilidade das reações, baixa potência e instabilidades dos materiais empregados nos eletrodos e dos solventes eletrolíticos. Assim, neste trabalho um modelo cinético foi empregado para os dados experimentais de espectroscopia de impedância eletroquímica, para a obtenção das constantes cinéticas das etapas elementares do mecanismo da reação de redução de oxigênio (RRO), o que permitiu investigar a influência de parâmetros como o tipo e tamanho de partícula do eletrocatalisador, o papel do solvente utilizado na RRO e compreender melhor as reações ocorridas no cátodo dessa bateria. A investigação inicial se deu com a utilização de sistemas menos complexos como uma folha de platina ou eletrodo de carbono vítreo como eletrodos de trabalho em 1,2-dimetoxietano (DME)/perclorato de lítio (LiClO4). A seguir, sistemas complexos com a presença de nanopartículas de carbono favoreceu o processo de adsorção das moléculas de oxigênio e aumentou ligeiramente (uma ordem de magnitude) a etapa de formação de superóxido de lítio (etapa determinante de reação) quando comparada com os eletrodos de platina e carbono vítreo, atribuída à presença dos grupos laterais mediando à transferência eletrônica para as moléculas de oxigênio. No entanto, foi observada uma rápida passivação da superfície eletrocatalítica através da formação de filmes finos de Li2O2 e Li2CO3 aumentando o sobrepotencial da bateria durante a carga (diferença de potencial entre a carga e descarga > 1 V). Adicionalmente, a incorporação das nanopartículas de platina (Ptnp), ao invés da folha de platina, resultou no aumento da constante cinética da etapa determinante da reação em duas ordens de magnitude, o qual pode ser atribuído a uma mudança das propriedades eletrônicas na banda d metálica em função do tamanho nanométrico das partículas, e estas modificações contribuíram para uma melhor eficiência energética quando comparado ao sistema sem a presença de eletrocatalisador. Entretanto, as Ptnp se mostraram não específicas para a RRO, catalisando as reações de degradação do solvente eletrolítico e diminuindo rapidamente a eficiência energética do dispositivo prático, devido ao acúmulo de material no eletrodo. O emprego de líquido iônico como solvente eletrolítico, ao invés de DME, promoveu uma maior estabilização do intermediário superóxido formado na primeira etapa de transferência eletrônica, devido à interação com os cátions do líquido iônico em solução, o qual resultou em um valor de constante cinética da formação do superóxido de três ordens de magnitude maior que o obtido com o mesmo eletrodo de carbono vítreo em DME, além de diminuir as reações de degradação do solvente. Estes fatores podem contribuir para uma maior potência e ciclabilidade da bateria de lítio-ar operando com líquidos iônicos.