Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Considerations on corrosion and weld repair effects on the fatigue strength of a steel structure critical to the flight-safety

The aim of this study is to analyze the effects of corrosion and successive tungsten inert gas (TIC) welding repairs on the reverse bending fatigue strength of AISI 4130 steel used in components critical to the flight-safety. The tests were performed on hot-rolled steel plate specimens, 1.10 mm and 1.60 mm thick, by means of a SCHENK PWS equipment, with load ratio R = -1, constant amplitude, 30 Hz frequency and room temperature. It was observed that the reverse bending fatigue strength of AISI 4130 steel decreases due to the corrosion and the TIC welding and re-welding processes. (C) 2010 Elsevier Ltd. All rights reserved.

Variation Guggenheim 3. A Pedestrian Steel Structure

Pedestrian Unique Bridge in prestesed white concrete. Pilar de la Horadada. Alicante.

Influence of laser surface texturing on surface microstructure and mechanical properties of adhesive joined steel sheets

This work discusses the resultant microstructure of laser surface treated galvanised steel and the mechanical properties of adhesively bonded surfaces therein. The surface microstructure obtained at laser intensities between 170 and 1700 MW cm 22 exhibit zinc melting and cavity formation. The wavy surface morphology of the treated surface exhibits an average roughness Ra between 1.0 and 1.5 mu m, and a mean roughness depth R(z) of 8.6 mu m. Atomic force microscopic analyses revealed that the R(z) inside the laser shot cavities increased from 68 to 243 nm when the incident laser intensity was increased from 170 to 1700 MW cm(-2). X-ray fluorescence analyses were used to measure Zn coating thicknesses as a function of process parameters. Both X-ray fluorescence and X-ray diffraction analyses demonstrated that the protective coating remains at the material surface, and the steel structure beneath was not affected by the laser treatment. Tensile tests under peel strength conditions demonstrated that the laser treated adhesively joined samples had resistance strength up to 88 MPa, compared to a maximum of only 23 MPa for the untreated surfaces. The maximum deformation for rupture was also greatly increased from 0.07%, for the original surface, to 0.90% for the laser treated surfaces.

A cost study of common surface finish systems for steel structures

This paper presents part of a study aimed at finding a suitable, yet cost-effective, surface finish for a steel structure subject to the car washing environment and corrosive chemicals. The initial, life cycle and average equivalent annual (AEAC) costs for surface finishing methods were calculated for a steel structure using the LCCC algorithm developed by American Galvanizers Association (AGA). The cost study consisted of 45 common surface finish systems including: hot-dip galvanization (HDG), metallization, acrylic, alkyd and epoxy as well as duplex coatings such as epoxy zinc and inorganic zinc (IOZ). The results show that initial, life cycle and AEAC costs for hot dip galvanization are the lowest among all the other methods, followed by coal tar epoxy painting. The annual average cost of HDG for this structure was estimated about €0.22/m2, while the other cost-effective alternatives were: IOZ, polyurea, epoxy waterborne and IOZ/epoxy duplex coating.

Automated formulation of optimisation models for steel beam structures

Over 70% of the total costs of an end product are consequences of decisions that are made during the design process. A search for optimal cross-sections will often have only a marginal effect on the amount of material used if the geometry of a structure is fixed and if the cross-sectional characteristics of its elements are property designed by conventional methods. In recent years, optimalgeometry has become a central area of research in the automated design of structures. It is generally accepted that no single optimisation algorithm is suitable for all engineering design problems. An appropriate algorithm, therefore, mustbe selected individually for each optimisation situation. Modelling is the mosttime consuming phase in the optimisation of steel and metal structures. In thisresearch, the goal was to develop a method and computer program, which reduces the modelling and optimisation time for structural design. The program needed anoptimisation algorithm that is suitable for various engineering design problems. Because Finite Element modelling is commonly used in the design of steel and metal structures, the interaction between a finite element tool and optimisation tool needed a practical solution. The developed method and computer programs were tested with standard optimisation tests and practical design optimisation cases. Three generations of computer programs are developed. The programs combine anoptimisation problem modelling tool and FE-modelling program using three alternate methdos. The modelling and optimisation was demonstrated in the design of a new boom construction and steel structures of flat and ridge roofs. This thesis demonstrates that the most time consuming modelling time is significantly reduced. Modelling errors are reduced and the results are more reliable. A new selection rule for the evolution algorithm, which eliminates the need for constraint weight factors is tested with optimisation cases of the steel structures that include hundreds of constraints. It is seen that the tested algorithm can be used nearly as a black box without parameter settings and penalty factors of the constraints.

Analysis and guidelines for implementation of EN 1090-2 Standard to assist execution class assignment of steel structures

Finnish design and consulting companies are delivering robust and cost-efficient steel structures solutions to a large number of manufacturing companies worldwide. Recently introduced EN 1090-2 standard obliges these companies to specify the execution class of steel structures for their customers. This however, requires clarifying, understanding and interpreting the sophisticated procedure of execution class assignment. The objective of this research is to provide a clear explanation and guidance through the process of execution class assignment for a given steel structure and to support the implementation of EN 1090-2 standard in Rejlers Oy, one of Finnish design and consulting companies. This objective is accomplished by creating a guideline for designers that elaborates on the four-step process of the execution class assignment for a steel structure or its part. Steps one to three define the consequence class (projected consequences of structure failure), the service category (hazards associated with the service use exploitation of steel structure) and the production category (manufacturing process peculiarities), based on the ductility class (capacity of structure to withstand deformations) and the behaviour factor (corresponds to structure seismic behaviour). The final step is the execution class assignment taking into account results of previous steps. Main research method is indepth literature review of European standards family for steel structures. Other research approach is a series of interviews of Rejlers Oy representatives and its clients, results of which have been used to evaluate the level of EN 1090-2 awareness. Rejlers Oy will use the developed novel coherent standard implementation guideline to improve its services and to obtain greater customer satisfaction.

Steel Pedestrian Bridge to Protect a Unique Tree

This paper describes the “Variation Guggenheim 3: Mirador de la palmera” project, situated in Daya Vieja (Alicante-Spain). This structure is inspired by the Guggenheim museum of New York and is designed to protect a land-mark palm-tree from wind loads. This six – trunk palm tree was declared monument by the Valencian government in 2012. The structure that now protect it appears to fly around de palm tree creating a helicoidally skywalk made of steel, while retrofitting the lateral trunks of the tree to protect them from collapse. An 18 m. long straight beam starts on the top of this helix, and stretches towards a lookout point that offers a view of the whole village and its surroundings. The reduction of the visual impact of the structure on the tree was a major aim for the project design. The structural elements are as slender as possible to avoid the visual obstruction of tree. They are painted white, while the walkway steel corrugated plate is painted green in order to highlight its neat shape among the blur created by the apparent mess of bars of the supporting structure. The two main piles of this pedestrian bridge were designed in steel and geometrically resemble trees. A Ground Penetrating Radar analysis was performed to detect the palm root location and to decide the best foundation system. Slender cast in-situ steel-concrete micropiles along with a concrete pile-cap, raised some centimeters above the ground level, were used to reduce the damage to the roots. The projected pile-cap is a slender, continuous, circular ring; which geometry resembles a concrete bench. This structure has been a finalist in the Architecture Awards for the 2010-2014 best construction projects, held by the Diputación de Alicante.

Structural steel design with BIM technology - interventions on a three buildings block in Deruta (PG)

The aim of this thesis is to use the developments, advantages and applications of "Building Information Modelling" (BIM) with emphasis on the discipline of structural design for steel building located in Perugia. BIM was mainly considered as a new way of planning, constructing and operating buildings or infrastructures. It has been found to offer greater opportunities for increased efficiency, optimization of resources and generally better management throughout the life cycle of a facility. BIM increases the digitalization of processes and offers integrated and collaborative technologies for design, construction and operation. To understand BIM and its benefits, one must consider all phases of a project. Higher initial design costs often lead to lower construction and operation costs. Creating data-rich digital models helps to better predict and coordinate the construction phases and operation of a building. One of the main limitations identified in the implementation of BIM is the lack of knowledge and qualified professionals. Certain disciplines such as structural and mechanical design depend on whether the main contractor, owner, general contractor or architect need to use or apply BIM to their projects. The existence of a supporting or mandatory BIM guideline may then eventually lead to its adoption. To test the potential of the BIM adoption in the steel design process, some models were developed taking advantage of a largely diffuse authoring software (Autodesk Revit), to produce construction drawings and also material schedule that were needed in order to estimate quantities and features of a real steel building. Once the model has been built the whole process has been analyzed and then compared with the traditional design process of steel structure. Many relevant aspect in term of clearness and also in time spent were shown and lead to final conclusions about the benefits from BIM methodology.

Utilização dos eurocódigos na construção metálica

Os Eurocódigos estruturais são um conjunto de normas técnicas que têm como objectivo abranger o projecto e verificação de qualquer tipo de construção para os países membros da União Europeia. O objectivo deste trabalho é sistematizar todos os procedimentos que estão presentes nos Eurocódigos e que são aplicáveis, de uma forma geral, à construção metálica. Foi feito o desenvolvimento de uma solução estrutural para o caso concreto de uma estrutura metálica de uma ponte rolante com o objectivo de se fazer o levantamento dos normativos estabelecidos para o projecto de estruturas metálicas. Este trabalho foi desenvolvido considerando fundamentalmente três Eurocódigos. O Eurocódigo 0 que estabelece o princípio e bases para o projecto de estruturas, o Eurocódigo 1 que define as acções em estruturas e o Eurocódigo 3 que estabelece as regras gerais, de verificação ao fogo, de projecto de ligações e de verificação à fadiga. O trabalho desenvolvido consistiu em projectar a estrutura metálica da ponte rolante considerada e para tal foram feitos os seguintes passos. - Determinação das acções na estrutura e das situações de projecto; - Projecto da estrutura considerando a verificação de cedência ou deformação excessiva dos seus elementos; - Projecto da estrutura considerando a perda de equilíbrio estático da estrutura; - Projecto da estrutura considerando a verificação da sua resistência ao fogo; - Projecto das ligações aparafusadas; - Verificação da resistência à fadiga.

Dimensionamento de um passadiço pedonal em estrutura metálica, com fundações em betão armado

A elaboração deste projecto, integrado no âmbito do Trabalho Final de Mestrado, para a obtenção do grau de Mestre em Engenharia Civil, tem como objectivo o dimensionamento de um passadiço pedonal em estrutura metálica, com fundações em betão armado. Este documento inclui quase todos os elementos necessários ao projecto de execução da referida estrutura. Para o dimensionamento do passadiço pedonal procedeu-se à quantificação das acções e posteriormente à verificação da segurança de todos os elementos estruturais tendo por base os critérios e especificações técnicas preconizados nas Normas Europeias relativas ao projecto estrutural (Eurocódigos estruturais). Tratando-se de um passadiço destinado à circulação de peões e cuja estrutura metálica apresenta um certo grau de flexibilidade devido à esbelteza dos elementos estruturais, esta poderá estar sujeita a acções dinâmicas periódicas provocadas pelas pessoas quando percorrem o passadiço, podendo ocasionar certos níveis de vibração que sob o ponto de vista de segurança estrutural serão pouco relevantes, sendo no entanto excessivos do ponto de vista do conforto humano. Foi por isso efectuado um estudo dinâmico, com o objectivo de caracterizar a resposta dinâmica da estrutura quando solicitada a carregamentos de natureza periódica como é o caso da acção do peão, de modo a garantir que a utilização desta estrutura esteja dentro dos parâmetros de conforto aceitáveis. A modelação da estrutura e consequente discretização geral desta, foi feita recorrendo a programa de elementos finitos, SAP2000, versão 14.0.0. O dimensionamento das ligações constitui outros dos aspectos fundamentais no projecto desta estrutura metálica.

Dimensionamento de um edifício metálico de ensacagem a construir numa instalação industrial

Trabalho de Projeto para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Estruturas

Estrutura metálica do teto falso da sala de comando da central Venda Nova III – acompanhamento da conceção, fabrico e montagem

O primeiro objetivo deste relatório, que adiante se desenvolve, é apresentar o trabalho realizado para a obtenção de conhecimentos que justifiquem a atribuição do grau de mestre em engenharia, no ramo das construções. O estágio, que a este trabalho dá sustentação, foi feito na empresa Metaloviana, onde foi possível acompanhar as várias fases de conceção, fabrico e montagem de um teto falso, designadamente na sala de comando da central Venda Nova III, de aproveitamento hidroelétrico. Tendo Portugal objetivos cada vez mais ambiciosos na utilização de energias renováveis, aproveitando, entre outros, os recursos hídricos para a produção de eletricidade, a EDP Produção fez estudos onde verificou que a realização de reforços de potência em aproveitamento já existentes, seria uma forma economicamente bastante atrativa e ao mesmo tempo responderia às crescentes solicitações energéticas. É neste âmbito que se insere o Reforço de Potência em Venda Nova III. A empresa Metaloviana, com instalações fabris em Viana do Castelo, tem todo um historial e capacidade, reconhecida nacional e internacionalmente. Este, confere a certeza de ter acompanhado um trabalho de ponta, devidamente creditado e fundamentado numa qualidade e mérito, por demais reconhecido.

Projeto de estabilidade de internato masculino

O presente documento corresponde à realização de um projeto de estruturas em betão armado e estrutura metálica. A escolha deste tema teve como propósito aplicar os conhecimentos adquiridos ao longo do percurso académico, sobretudo em disciplinas do ramo de estruturas. O trabalho desenvolvido é um Projeto de Estabilidade de Betão Armado e Estrutura Metálica de um Internato Masculino para Padres em Onameva, Cunene – Angola. A elaboração deste projeto decorre da realização de um estágio formal de 8 meses na empresa CALCULUS, Miguel Barros – Engenharia, LDA, com o objetivo principal de reunir os requisitos necessários à admissão na Ordem dos Engenheiros. No contexto laboral de um gabinete de projetos de engenharia civil, foi feita a integração de forma gradual e sustentada das competências adquiridas ao longo da formação académica e vivenciadas situações reais de trabalho profissional. De entre as atividades desenvolvidas no estágio, foi escolhido o projeto de estabilidade acima referido pela oportunidade de realizar todas as etapas do seu desenvolvimento, desde a análise da arquitetura até à elaboração das peças escritas e desenhadas, dando assim resposta às exigências necessárias para a conclusão do Mestrado em Engenharia Civil, no ramo de Estruturas, pelo Instituto Superior de Engenharia do Porto.

Análise de estabilidade e fundações de equipamentos de sinalização vertical rodoviária

O presente projeto foi realizado no âmbito da unidade curricular Dissertação/Estágio/Projeto, e desenvolve um estudo sobre as estruturas porticadas de sinalização vertical em Autoestradas, ao nível da estrutura metálica e das fundações, com o objetivo de analisar três casos diferentes com características distintas. Dois dos casos em estudo são modelos comuns que se encontram facilmente nas autoestradas. O terceiro tem uma configuração diferente, mais gravoso que o habitual. Com estes três casos obtém-se um estudo completo e abrangente deste tipo de estrutura porticada. Ao longo do projeto é seguida a norma EC3 (Eurocódigo 3 – Projeto de estruturas de aço). Dimensionaram-se as estruturas utilizando secções tubulares, mas é também realizado o dimensionamento de uma solução estrutural alternativa recorrendo a perfis laminados I ou H. As estruturas foram modeladas com recurso ao software de cálculo Autodesk Robot Structural Analysis Professional, obtendo-se os esforços e deformações nos vários pontos da estrutura, que permitem realizar o dimensionamento manual das secções dos perfis estruturais, chumbadouros, chapas de fundação e fundações propriamente ditas. Na parte final do projeto apresenta-se uma apreciação global do mesmo, conclusões gerais sobre os resultados obtidos e possíveis desenvolvimentos futuros.