Repair Welding Effects on the Bending Fatigue Strength of AISI 4130 Aeronautical Steel used in a Critical to the Flight-Safety Structure

The aim of this study was to analyze the effect of successive TIG (tungsten inert gas) welding repairs on the reverse bending fatigue strength of AISI 4130 steel, which is widely used in components critical to the flight-safety. In order to simulate the abrupt maneuvers, wind bursts, motor vibration and helixes efforts, which generate cyclic bending loadings at the welded joints of a specific aircraft component called motor cradle, experimental reverse bending fatigue tests were carried out on specimens made from hot-rolled steel plate, 1.10 mm (0.043 in) thick, by mean of a SCHENK PWS equipment, with load ratio R = -1, under constant amplitude, at 30 Hz frequency and room temperature. It was observed that the bending fatigue strength decreases after the TIG (Tungsten Inert Gas) welding process application on AISI 4130 steel, with subsequent decrease due to re-welding sequence as well. Microstructural analyses and microhardness measurements on the base material, heat-affected zone (HAZ) and weld metal, as well as the effects of the weld bead geometry on the obtained results, have complemented this study.

Effects of several TIG weld repairs on the axial fatigue strength of AISI 4130 aeronautical steel-welded joints

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Fatigue strength of tungsten inert gas-repaired weld joints in airplane critical structures

In this work the effect of Gas Tungsten Arc Welding (GTAW) repairs on the axial fatigue strength of an AISI 4130 steel welded joint used in airframe critical to the flight-safety was investigated. Fatigue tests were performed at room temperature on 0.89 mm thick hot-rolled plates with constant amplitude and load ratio of R = 0.1, at 20 Hz frequency. Monotonic tensile tests, optical metallography and microhardness, residual stress and weld geometric factors measurements were also performed. The fatigue strength decreased with the number of GTAW repairs, and was related to microstructural and microhardness changes, as well as residual stress field and weld profile geometry factors, which gave origin to high stress concentration at the weld toe. (C) 2011 Elsevier B.V. All rights reserved.

Considerations about the welding repair effects on the structural integrity of an airframe critical to the flight-safety

Structures critical to the flight-safety are commonly submitted to several maintenance repairs at the welded joints in order to prolong the in-service life of aircrafts. The aim of this study is to analyze the effects of Tungsten Inert Gas (TIG) welding repair on the structural integrity of the AISI 4130 aeronautical steel by means of experimental fatigue crack growth tests in base-material, heat-affected zone (HAZ) and weld metal. The tests were performed on hot-rolled steel plate specimens, 0.89 mm thick, with load ratio R = 0.1, constant amplitude, at 10 Hz frequency and room temperature. Increase of the fracture resistance was observed in the weld metal but decreasing in the HAZ after repair. The results were associated to microhardness and microstructural changes with the welding sequence. (C) 2010 Published by Elsevier Ltd.

Operator, organizational, and direct support maintenance manual, including repair parts and special tools lists : welding shop, trailer mounted, Libby model unassigned, FSN 3431-935-7821.

"February 1972."

Direct support, general support, and depot maintenance repair parts and special tools lists : welding machine, arc, AC/DC, 300 amp, transformer rectifier, constant current, base mounted (Eutectic Corp. model MD301 FED), FSN 3431-235-4728.

"October 1971."

Organizational, DS, GS, and depot maintenance manual including repair parts : welding machine, arc, generator, electric motor driven, 300-amp DC arc, 220/440-V, 60-cycle, 3-phase, wheel mounted (Harnischfeger model W300 MG), FSN 3431-226-1569).

"April 1965."

Organizational maintenance repair parts and special tools lists : welding set, ARC, inert gas shielded, plastic or metal lined gun; for 3/64 in. wire; DC, 115V., (Linde model SWM-9-A) FSN 3431-972-7672.

"May 1970."

Organizational, direct and general support, and depot maintenance repair parts and special tools list : welding machine, ARC, G.E.D. generator, 300 amp, DC, constant current, consistant potential, skid mounted, (Libby welding model LTO 300), FSN 3431-253-0558.

"March 1971."

Organizational, DS, GS and depot maintenance repair parts and special tools list : welding set, ARC, inert gas shielded, air cooled, metal lined gun for 3/64 in. wire, (Westinghouse model SA-136), FSN 3431-121-5878.

"July 1971."

Organizational, maintenance repair parts, and special tools lists : welding machine, arc, generator, GED, 300 amp, DC (Libby welding models) (model LE-300) FSN 3431-810-9696, (model LEW-300) FSN 3431-991-2961, (model LEB-300) FSN 3431-072-0327.

"January 1971."

Organizational and direct support maintenance repair parts and special tools list : welding set, arc, inert gas shielded, water cooled, aluminum welding, general purpose (Airco model 23511209), FSN 3431-731-4163.

"December 1970."

Operator, organizational, direct support, and general support maintenance manual, including repair parts and special tools list : welding machine, arc, general and inert gas, shielded, transformer-rectifier type, AC and DC, 300 ampere rating at 60% duty cycle (Harnischfeger model DAR-300HFSG), FSN 3431-984-3401, (Harnischfeger model 2100H2007), FSN 3431-926-3746.

Includes index.

Organizational maintenance repair parts and special tools list : welding set, arc, inert gas shielded, plastic or metal lined gun, for 3/64 in. wire, DC, 115V (Westinghouse model SA-135), FSN 3431-879-9709.

Includes index.

Direct and general support and depot maintenance repair parts and special tools list : welding machine, arc, generator, electric motor driven, AC, 220V, 3 phrase [i.e. phase], 60HZ, single operator, remote control, 300 amp DC arc, wheel MTD ....

"December 1968."