A simple analysis of the changes during evaporation of a commercial emulsion of unknown composition

Optical microscopy and centrifugation were used to observe the Structural changes during evaporation of a commercial skin lotion of unknown composition. The degree of evaporation was determined from the changed weight of a microscope slide with the emulsion on a defined area and thickness, the evaporation loss versus time being measured by a balance under an infrared lamp. The results revealed not only which parts of the emulsion were most prone to evaporation without chemical analysis, but also gave surprising information as to which kind of structures would appear after extensive evaporation. The importance of these changes for the action of a skin lotion is briefly discussed.

A Comparative Analysis of the Changes During Evaporation of Three Different Commercial Emulsion of Unknown Composition

Optical microscope and centrifugation were used to observe the structure change during evaporation of three different commercial emulsions of unknown composition. The degree of evaporation under an infrared lamp at 70 degrees C was determined from the changed weight of a microscope slide with the emulsion on a defined area and thickness. The results revealed information as to which kind of structure would appear after evaporation.

Refractive index matching applied to fecal smear clearing

Thick smears of human feces can be made adequate for identification of helminth eggs by means of refractive index matching. Although this effect can be obtained by simply spreading a fleck of feces on a microscope slide, a glycerol solution has been routinely used to this end. Aiming at practicability, a new quantitative technique has been developed. To enhance both sharpness and contrast of the images, a sucrose solution (refractive index = 1.49) is used, which reduces the effect of light-scattering particulates. To each slide a template-measured (38.5 mm³) fecal sample is transferred. Thus, egg counts and sensitivity evaluations are easily made.

Citologia aspirativa por agulha fina (CAAF), em testículo de onça pintada (Panthera onca), utilizada como ferramenta no diagnóstico de infertilidade

Técnicas de biópsia, caracterizadas pela remoção de segmentos de órgãos e tecidos para análise histopatológica, não são indicadas no auxílio diagnóstico de alterações testiculares para animais ameaçados de extinção, por não serem totalmente isentas de riscos. Neste sentido, é de grande interesse que se desenvolvam técnicas de biópsia testicular cada vez mais seguras e com o mínimo de conseqüências negativas. Com este intuito três onças pintadas (Panthera onca) foram submetidas a exames de Citologia Aspirativa por Agulha Fina (CAAF). Amostras foram obtidas através da punção aspirativa dos testículos, esfregaços foram confeccionados, corados com Panótico e analisados sob Microscopia Óptica. Simultaneamente foram realizadas coletas de sêmen para avaliação do volume, pH, concentração, motilidade, vigor e morfologia espermáticas. Quanto à avaliação espermática, os animais apresentaram valores semelhantes aos encontrados na literatura quanto ao volume, pH, motilidade, vigor e morfologia espermáticas. Quanto a concentração espermática os animais apresentaram valores abaixo dos encontrados na literatura. Nos exames de CAAF, todas as gerações de células germinativas foram identificadas, indicando espermatogênese normal em todos os animais, com exceção das espermátides finais duplas que ainda não foram relatadas como achados em punções testiculares de outras espécies, o que vem confirmar a elevada porcentagem de células teratológicas encontradas nesses animais. Desta forma, podemos concluir que a CAAF testicular é um método diagnóstico auxiliar importante na detecção de alterações testiculares em casos de sub ou infertilidade, podendo ser utilizados na rotina de investigação do trato reprodutivo masculino, quando o exame histopatológico, por ser um método altamente invasivo, é desaconselhável.

A mechatronic system applied to wear particle analysis

This paper describes the development of a mechatronic system for a predictive maintenance grounded on wear particle analysis. The reckoning of wear particles containing in lubricating industrial oils brings the image acquisition system into being. The ISO 4406:1999 standard is a guide to establish the counting and evaluation processes of particles. The system applied to the acquisition and analysis of the data consists of a digital camera, a monocular microscope and an oil filtering system. A computational program was developed with the application of Visual Microsoft C++ in a way to detain the oil sample image from the microscope slide to the computer screen. Quantitative analyses of the wear debris particles bulk are exploited applying a graphical interface that was developed to render the image processing of the sample test. The implemented system has a reachable cost thus it can be applied for schooling goals and for bolstering laboratories of minor industries and medium size companies.

Relação da ciclooxigenase-2 com VEGF e a caspase-3 nas neoplasias mamárias de cadelas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aceria litchii (Keifer) em lichia: ocorrência sazonal, danos provocados e identificação de possíveis agentes de controle biológico

Pós-graduação em Agronomia - FEIS

Estudo da morfologia funcional reprodutiva e desenvolvimento larval em laboratório de Stenopus hispidus(Olivier, 1811) (Crustacea, Decapoda, Stenopodidea)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of early nutrition on the wnt and bone morphogenic protein pathways in the developing intestine

Infant formula is consumed by the majority of infants in the United States for at least part of the first year of life. Infant formula lacks many of the bioactive compounds that are naturally occurring in breast milk. Because of this, there has been an increased interest by the companies that manufacture infant formula to include additives that would potentially allow formula to more closely mimic breast milk activity. One such ingredient currently being added to infant formula is prebiotics. Prebiotics are non-digestible food ingredients that beneficially affect the host by selectively stimulating the growth of specific healthful bacteria in the colon. It is speculated that prebiotics replicate the activity of breast milk oligosaccharides, which through the production of butyrate by intestinal microbiota, may interact with the Wnt/BMP pathways. The Wnt/BMP pathways regulate intestinal stem cells, which determine the growth, development and maintenance of the intestine. Therefore, the objective of this study was to explore the effects that the addition of prebiotics to formula have on the regulation of the Wnt/BMP pathways when fed to neonatal piglets, a model commonly used in the study of infant nutrition. Piglets (n=5) were randomized into sow-reared (SR), fed control formula (F), or fed formula with added prebiotics (F+P). Fructooligosaccharides (FOS) (2 g/L) and polydextrose (PDX) (2 g/L) were chosen as the prebiotics for this study, because this combination had been less studied than other combinations. Ileum and ascending colon were collected at 7 and 14 days-of-age. Dry matter content, pH, and short chain fatty acid (SCFA) content was measured. The mRNA expression of β-catenin, sFRP3, sFRP4, frizzled 6, DKK1 (Wnt pathway), gremlin (BMP pathway), TNF-a, HNF-4α and osteopontin (OPN) was measured by RT-qPCR. Piglets fed the F+P diet had greater acetate concentration and lower pH in the ileum at day 14 and in the colon at day 7 and day 14 than F piglets. Butyrate concentrations were highest in SR with F+P not differing from F in ileum at day 14 and colon at day 7 and day 14. Effects of age were seen in all genes, with the exception of OPN, sFRP-3 and sFRP-4. On day 7, no effect of diet was observed in the ileum, however, mRNA expression of DKK1 and frizzled 6 were greater in F+P than SR (p≤0.05). On day 14, gremlin expression was lower and OPN was greater in the ileum of SR piglets compared to F and F+P. Also on day 14, HNF-4α mRNA expression was greater in both ileum and colon of F+P piglets and sFRP3 mRNA expression was greater in the colon than F or SR . In summary, differences were observed between gene expression of F+P and SR piglet intestines, but the supplementation of 2 g/L scFOS and 2 g/L PDX to formula did not shift expression of genes in the Wnt/BMP pathways to be more similar to SR than F. As the Wnt/BMP pathway is known to exist in a gradient along the crypt-villus axis, with Wnt expression dominating in the crypt region and BMP expression dominating in the villi, it was possible that pooling whole tissue reduced our ability to detect treatment effects that would be concentrated in either region. A method was therefore developed to remove intestinal epithelial cells along the villus-to-crypt axis. Twenty-five-day-old F and SR piglets were euthanized and ileal tissue was collected and placed in a dissociation buffer in a shaking water bath. Exfoliated cells were removed at increasing time points from 5 to 100 minutes in order to remove cells along the villus-to-crypt axis. After the final incubation, remaining mucosal tissue was removed using a sterile glass microscope slide and pooled with the final exfoliated cell isolation. After each cell collection, a section of tissue was fixed in formalin for histomorphological examination. Expression of genes in the Wnt/BMP pathways, along with crypt marker genes (CDK5 and v-myb), were measured in both whole ileal tissue, pooled epithelial cells, and separate epithelial cell isolations from the same piglet. The expression of β-catenin, HNF-4α, TNF-α, TGF-β and the crypt marker v-myb matched the expected villus-to-crypt pattern in cells collected after 10 (incubation 1), 30 (incubation 2) and 60 (incubation 3) minutes. However, expression of expression in cells collected after 100 minutes (incubation 4) was variable, which may be due to the fact that crypt cells were not efficiently removed and the presence of unwanted non-epithelial tissue. Gremlin, OPN, DKK1, sFRP3 and sFRP4 expression was not statistically different along the villus-to-crypt axis. Frizzled 6 and CDK5 did not express as we had predicted, with expression highest towards the villi. In summary, the epithelial cell collection method used was not entirely successful. While much of the gene data suggests that cells were removed along the villus-to-crypt axis through the first three incubations, the last incubation, which involved scraping the tissue, removed non-epithelial components of the mucosa, while leaving the crypts intact. In conclusion, the addition of 2 g/L PDX and 2 g/L scFOS did not cause gene expression of the Wnt/BMP pathways to mirror either F or SR expression. New isolation methods to extract cells along the crypt-villus axis should be considered, including the use of a laser capture microdissection. While this combination of prebiotics did not yield the intended effects, future research should be done on other combinations, such as the inclusion of galactooligosaccharides (GOS), which is commonly added to food products including infant formula.

Implementation of a virtual correlative light and transmission electron microscope

In the long run, the widespread use of slide scanners by pathologists requires an adaptation of teaching methods in histology and cytology in order to target these new possibilities of image processing and presentation via the internet. Accordingly, we were looking for a tool with the possibility to teach microscopic anatomy, histology, and cytology of tissue samples which would be able to combine image data from light and electron microscopes independently of microscope suppliers. With the example of a section through the villus of jejunum, we describe here how to process image data from light and electron microscopes in order to get one image-stack which allows a correlation of structures from the microscopic anatomic to the cytological level. With commercially available image-presentation software that we adapted to our needs, we present here a platform which allows for the presentation of this new but also of older material independently of microscope suppliers.

Transition From Glass To Digital Slide Microscopy In The Teaching Of Oral Pathology In A Brazilian Dental School.

Several medical and dental schools have described their experience in the transition from conventional to digital microscopy in the teaching of general pathology and histology disciplines; however, this transitional process has scarcely been reported in the teaching of oral pathology. Therefore, the objective of the current study is to report the transition from conventional glass slide to virtual microscopy in oral pathology teaching, a unique experience in Latin America. An Aperio ScanScope® scanner was used to digitalize histological slides used in practical lectures of oral pathology. The challenges and benefits observed by the group of Professors from the Piracicaba Dental School (Brazil) are described and a questionnaire to evaluate the students' compliance to this new methodology was applied. An improvement in the classes was described by the Professors who mainly dealt with questions related to pathological changes instead of technical problems; also, a higher interaction with the students was described. The simplicity of the software used and the high quality of the virtual slides, requiring a smaller time to identify microscopic structures, were considered important for a better teaching process. Virtual microscopy used to teach oral pathology represents a useful educational methodology, with an excellent compliance of the dental students.

Novel method for measuring nanofriction by atomic force microscope

The authors describe a novel approach to the measurement of nanofriction, and demonstrate the application of the method by measurement of the coefficient of friction for diamondlike carbon (DLC) on DLC, Si on DLC, and Si on Si surfaces. The technique employs an atomic force microscope in a mode in which the tip moves only in the z (vertical) direction and the sample surface is sloped. As the tip moves vertically on the sloped surface, lateral tip slipping occurs, allowing the cantilever vertical deflection and the frictional (lateral) force to be monitored as a function of tip vertical deflection. The advantage of the approach is that cantilever calibration to obtain its spring constants is not necessary. Using this method, the authors have measured friction coefficients, for load range 0 < L M 6 mu N, of 0.047 +/- 0.002 for Si on Si, 0.0173 +/- 0.0009 for Si on DLC, and 0.0080 +/- 0.0005 for DLC on DLC. For load range 9 < L < 13 mu N, the DLC on DLC coefficient of friction increased to 0.051 +/- 0.003. (C) 2008 American Vacuum Society.

Scanning tunneling microscope operating as a spin diode

We theoretically investigate spin-polarized transport in a system composed of a ferromagnetic scanning-tunneling-microscope (STM) tip coupled to an adsorbed atom (adatom) on a host surface. Electrons can tunnel directly from the tip to the surface or via the adatom. Since the tip is ferromagnetic and the host surface (metal or semiconductor) is nonmagnetic we obtain a spin-diode effect when the adatom is in the regime of single occupancy. This effect leads to an unpolarized current for direct bias (V > 0) and polarized current for reverse (V < 0) bias voltages, if the tip is nearby the adatom. Within the nonequilibrium Keldysh technique we analyze the interplay between the lateral displacement of the tip and the intra adatom Coulomb interaction on the spin-diode effect. As the tip moves away from the adatom the spin-diode effect vanishes and the currents become polarized for both V > 0 and V < 0. We also find an imbalance between the up and down spin populations in the adatom, which can be tuned by the tip position and the bias. Finally, due to the presence of the adsorbate on the surface, we observe spin-resolved Friedel oscillations in the current, which reflects the oscillations in the calculated local density of states (LDOS) of the subsystem surface + adatom.

Phase-Locked Loop design applied to frequency-modulated atomic force microscope

The atomic force microscope (AFM) introduced the surface investigation with true atomic resolution. In the frequency modulation technique (FM-AFM) both the amplitude and the frequency of oscillation of the micro-cantilever must be kept constant even in the presence of tip-surface interaction forces. For that reason, the proper design of the Phase-Locked Loop (PLL) used in FM-AFM is vital to system performance. Here, the mathematical model of the FM-AFM control system is derived considering high order PLL In addition a method to design stable third-order Phase-Locked Loops is presented. (C) 2010 Elsevier B.V. All rights reserved.

Measuring the interaction forces between protein inclusion bodies and an air bubble using an atomic force microscope

Interaction forces between protein inclusion bodies and an air bubble have been quantified using an atomic force microscope (AFM). The inclusion bodies were attached to the AFM tip by covalent bonds. Interaction forces measured in various buffer concentrations varied from 9.7 nN to 25.3 nN (+/- 4-11%) depending on pH. Hydrophobic forces provide a stronger contribution to overall interaction force than electrostatic double layer forces. It also appears that the ionic strength affects the interaction force in a complex way that cannot be directly predicted by DLVO theory. The effects of pH are significantly stronger for the inclusion body compared to the air bubble. This study provides fundamental information that will subsequently facilitate the rational design of flotation recovery system for inclusion bodies. It has also demonstrated the potential of AFM to facilitate the design of such processes from a practical viewpoint.