MOCVD growth andproperties of GaN and AlGaN layers

In this work GaN and AlGaN layers were grown by metal-organic chemical vapor deposition (MOCVD) on sapphire substrates. The research was carried out at Micro and Nanoscience Laboratory of Helsinki University of Technology. The objective of this thesis is the study of MOCVD technique for the growth of GaN and AlGaN films and optimization of growth parameters in purpose to improve crystal quality of the films. The widely used two-step and the new multistep methods have been used for GaN, AlGaN MOCVD growth on c-plane sapphire. Properties of the GaN and AlGaN layers were studied using in-situ reflectance monitoring during MOCVD growth, atomic force microscopy and x-ray diffraction. Compared to the two step method, the multistep method has produced even better qualities of the GaN and AlGaN layers and significant reduction of threading dislocation density.

High Indium Concentration InGaN/GaN Grown on Sapphire Substrate by MOCVD

The InGaN system provides the opportunity to fabricate light emitting devices over the whole visible and ultraviolet spectrum due to band-gap energies E[subscript g] varying between 3.42 eV for GaN and 1.89 eV for InN. However, high In content in InGaN layers will result in a significant degradation of the crystalline quality of the epitaxial layers. In addition, unlike other III-V compound semiconductors, the ratio of gallium to indium incorporated in InGaN is in general not a simple function of the metal atomic flux ratio, f[subscript Ga]/f[subscript In]. Instead, In incorporation is complicated by the tendency of gallium to incorporate preferentially and excess In to form metallic droplets on the growth surface. This phenomenon can definitely affect the In distribution in the InGaN system. Scanning electron microscopy, room temperature photoluminescence, and X-ray diffraction techniques have been used to characterize InGaN layer grown on InN and InGaN buffers. The growth was done on c-plane sapphire by MOCVD. Results showed that green emission was obtained which indicates a relatively high In incorporation.

The molecular structure of propylene sulphide (methylthiirane) by gas-phase electron diffraction and theoretical calculations: a molecule used in MOCVD

Gas-phase electron-diffraction (GED) data together with results from ab initio molecular orbital calculations have been used to determine the structure of propylene sulphide. Values found for the main structural parameters for the molecule are consistent with those obtained from microwave studies and are compared here with those found for similar sulphur containing rings of general formula S(CH2)n (n = 2–5). A high ring strain enthalpy was calculated for propylene sulphide which is consistent with the small C–S–C angle (48.2(6)degrees) and the relatively long C–S bond lengths (ra = 1.831(2) Å). This is thought to account for the ease of ring opening in propylene sulphide observed in MOCVD reactions and the ready polymerisation of the molecule.

Growth and application of planar III-V semiconductor nanowires grown with MOCVD

The semiconductor nanowire has been widely studied over the past decade and identified as a promising nanotechnology building block with application in photonics and electronics. The flexible bottom-up approach to nanowire growth allows for straightforward fabrication of complex 1D nanostructures with interesting optical, electrical, and mechanical properties. III-V nanowires in particular are useful because of their direct bandgap, high carrier mobility, and ability to form heterojunctions and have been used to make devices such as light-emitting diodes, lasers, and field-effect transistors. However, crystal defects are widely reported for III-V nanowires when grown in the common out-of-plane <111>B direction. Furthermore, commercialization of nanowires has been limited by the difficulty of assembling nanowires with predetermined position and alignment on a wafer-scale. In this thesis, planar III-V nanowires are introduced as a low-defect and integratable nanotechnology building block grown with metalorganic chemical vapor deposition. Planar GaAs nanowires grown with gold seed particles self-align along the <110> direction on the (001) GaAs substrate. Transmission electron microscopy reveals that planar GaAs nanowires are nearly free of crystal defects and grow laterally and epitaxially on the substrate surface. The nanowire morphology is shown to be primarily controlled through growth temperature and an ideal growth window of 470 +\- 10 °C is identified for planar GaAs nanowires. Extension of the planar growth mode to other materials is demonstrated through growth of planar InAs nanowires. Using a sacrificial layer, the transfer of planar GaAs nanowires onto silicon substrates with control over the alignment and position is presented. A metal-semiconductor field-effect transistor fabricated with a planar GaAs nanowire shows bulk-like low-field electron transport characteristics with high mobility. The aligned planar geometry and excellent material quality of planar III-V nanowires may lead to highly integrated III-V nanophotonics and nanoelectronics.

Growth and Characterization of III-V Semiconductor Materials for MOCVD Reactor Qualification and Process Control

Metalorganic chemical vapor deposition is examined as a technique for growing compound semiconductor structures. Material analysis techniques for characterizing the quality and properties of compound semiconductor material are explained and data from recent commissioning work on a newly installed reactor at the University of Illinois is presented.

Low-frequency noise and static analysis of the impact of the TiN metal gate thicknesses on n- and p-channel MuGFETs

The impact of the titanium nitride (TIN) gate electrode thickness has been investigated in n and p channel SOI multiple gate field effect transistors (MuGFETs) through low frequency noise charge pumping and static measurements as well as capacitance-voltage curves The results suggest that a thicker TIN metal gate electrode gives rise to a higher EOT a lower mobility and a higher interface trap density The devices have also been studied for different back gate biases where the GIFBE onset occurs at lower front-gate voltage for thinner TIN metal gate thickness and at higher V(GF) In addition it is demonstrated that post deposition nitridation of the MOCVD HfSiO gate dielectric exhibits an unexpected trend with TIN gate electrode thickness where a continuous variation of EOT and an increase on the degradation of the interface quality are observed (C) 2010 Elsevier Ltd All rights reserved

Synthesis of anatase TiO2 supported on porous solids by chemical vapor deposition

Coating anatase TiO2 onto three different particle supports, activated carbon (AC), gamma -alumina (Al2O3) and silica gel (SiO2), by chemical vapor deposition (CVD) was studied. The effect of the CVD synthesis conditions on the loading rate of anatase TiO2 was investigated. It was found that introducing water vapor during CVD or adsorbing water before CVD was crucial to obtain anatase TiO2 on the surface of the particle supports. The evaporation temperature of precursor, deposition temperature in the reactor, flow rate of carrier gas, and the length of coating time were also important parameters to obtain more uniform and repeatable TiO2 coating. High inflow precursor concentration, high CVD reactor temperature and long coating time tended to cause block problem. Coating TiO2 onto small particles by CVD involved both chemical vapor deposition and particle deposition. It was believed that the latter was the reason for the block problem. In addition, the mechanism of CVD process in this study included two parts, pyrolysis and hydrolysis, and one of them was dominant in the CVD process under different synthesis route. Among the three types of materials, silica gel, with higher surface hydroxyl groups and macropore surface area, was found to be the most efficient support in terms of both anatase TiO2 coating and photocatalytic reaction. (C) 2001 Elsevier Science B.V. All rights reserved.

Optical properties and transport in PLD-GaN

We present structural, optical and transport data on GaN samples grown by hybrid, two-step low temperature pulsed laser deposition. The band gap of samples with good crystallinity has been deduced from optical spectra. Large below gap band tails were observed. In samples with the lowest crystalline quality the PL spectra are quite dependent on spot laser incidence. The most intense PL lines can be attributed to excitons bounded to stacking faults. When the crystalline quality of the samples is increased the ubiquitous yellow emission band can be detected following a quenching process described by a similar activation energy to that one found in MOCVD grown samples. The samples with the highest quality present, besides the yellow band, show a large near band edge emission which peaked at 3.47 eV and could be observed up to room temperature. The large width of the NBE is attributed to effect of a wide distribution of band tail states on the excitons. Photoconductivity data supports this interpretation.

Fabrication and characterisation of ferroelectric lead zirconate titanate and strontium bismuth tantalate thin films

Ferroelectrics, liquid delivery, MOCVD, lead zirconate titanate, strontium bismuth tantalate

MOVPE growth and characterisation of ZnO properties for optoelectronic applications

ZnO, Epitaxy, Metal organic vapor phase epitaxy, MOCVD, CVD, Semiconductor, Optoelectronics, X-ray diffraction, Cathodoluminescence, Microelectronics

Wachstum von Galliumnitrid-basierten Bauelementen auf Silizium(001)-Substraten mittels metallorganischer Gasphasenepitaxie

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2009

Metallorganische Gasphasenepitaxie und Charakterisierung homoepitaktischer ZnO-Schichten

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2009