Dielectric relaxation around the nematic-isotropic transition of liquid crystalline polymers

This study is concerned with a series of acrylate based side-chain liquid crystalline (LC) polymers. Previous studies have shown that these LC polymers have a preference for parallel or perpendicular alignment with respect to the polymer chain which depends on the length of the coupling chain joining the mesogenic unit to the polymer backbone. On the other hand, the dielectric relaxation of these side-chain LC polymers shows a strong relaxation associated to the mesogenic unit dynamics. For samples with parallel alignment, it was found that the dielectric relaxation of the nematic is weaker and broader than the relaxation of the isotropic. By contrast, for samples with perpendicular alignment, the isotropic to nematic transition reduces the broadening the relaxation and increases the relaxation strength. These two features are more evident for samples with short coupling units for which the dielectric relaxation observed appears to be strongly coupled with the backbone dynamics.

Water-Based Cellulose Liquid Crystal System Investigated by Rheo-NMR

Water-based cellulose cholesteric liquid crystalline phases at rest can undergo structural changes induced by shear flow. This reflects on the deuterium spectra recorded when the system is investigated by rheo-nuclear magnetic resonance (rheo-NMR) techniques. In this work, the model system hydroxypropylcellulose (HPC)+water is revisited using rheo-NMR to clarify unsettled points regarding its behavior under shear and in relaxation. The NMR spectra allow the identification of five different stable ordering states, within shear and relaxation, which are well integrated in a mesoscopic picture of the system's structural evolution under shear and relaxation. This picture emerging from the large body of studies available for this system by other experimental techniques, accounts well for the NMR data and is in good agreement with the three distinct regions of steady shear flow recognized for some lyotropic LC polymers. Shear rates in between 0.1 and 1.0 s(-1) where investigated using a Taylor-Couette flow and deuterated water was used as solvent for the deuterium NMR (DNMR) analysis.

Liquid crystal polymer brushes and their application as alignment layers in liquid crystal cells

Liquid Crystal Polymer Brushes and their Application as Alignment Layers in Liquid Crystal Cells Polymer brushes with liquid crystalline (LC) side chains were synthesized on planar glass substrates and their nematic textures were investigated. The LC polymers consist of an acrylate or a methacrylate main chain and a phenyl benzoate group as the mesogenic unit which is connected to the main chain via a flexible alkyl spacer composed of six CH2 units. The preparation of the LC polymer brushes was carried out according to the “grafting from” technique: polymerization is carried out from azo-initiators that have been previously self-assembled on the substrate. LC polymer brushes with a thickness from a few nm to 230 nm were synthesized by varying the monomer concentration and the polymerization time. The LC polymer brushes were thick enough to allow for direct observation of the nematic textures with a polarizing microscope. The LC polymer brushes grown on untreated glass substrates exhibited irregular textures (“polydomains”). The domain size is in the range of some micrometers and depends only weakly on the brush thickness. The investigations on the texture-temperature relationship of the LC brushes revealed that the brushes exhibit a surface memory effect, that is, the identical texture reappears after the LC brush sample has experienced a thermal isotropization or a solvent treatment, at which the nematic LC state has been completely destroyed. The surface memory effect is attributed to a strong anchoring of the orientation of the mesogenic units to heterogeneities at the substrate surface. The exact nature of the surface heterogeneities is unknown. The effect was observed for the LC brushes swollen with low molecular weight nematic molecules, as well. Rubbing the glass substrate with a piece of velvet cloth prior to the surface modification with the initiator and the brush growth gives rise to the formation of homogenous alignment of the mesogenic units in the LC polymer side chains. Monodomain textures were obtained for these LC brushes. The mechanism for the homogeneous alignment is based on the transfer of Nylon fibers during the rubbing process. A surfactant was mixed with the azo-initiator in modifying rubbed substrates for subsequent brush generation. Such brushes exhibited biaxial optical properties. Hybrid LC cells made from a substrate modified with biaxial brushes and a rubbed glass substrate show an orientation with a tilt angle of a = –15.6 . This work shows that LC brushes grown on rubbed surfaces fulfill the important criteria for alignment layers: the formation of macroscopic monodomains. First results indicate that by diluting the brush with molecules which are also covalently bound to the surface but induce a different orientation, a system is obtained in which the two conflicting alignment mechanisms can be used to generate a tilted alignment. In order to allow for an application of the alignment layers into a potential product, subsequent work should focus on the questions how easy and in which range the tilt angle can be controlled.

Synthese von flüssigkristallinen Polysiloxanen und Charakterisierung der smektischen Phasen

Gegenstand dieser Arbeit ist die Untersuchung der smektischen Phasen von Polysiloxanen mit flüssigkristallinen Seitengruppen (LC-Polysiloxane). Der erste Teil der vorliegenden Arbeit befasste sich mit der Herstellung verschiedener flüssigkristalliner ferroelektrischer Polysiloxane. Die Polymere wurden in Bezug auf das verwendete Polymerrückgrat (Homo- und Copolysiloxan) sowie durch den zusätzlichen Einbau von vernetzbaren Seitengruppen variiert. Im zweiten Teil der Arbeit wurden die Eigenschaften der smektischen Phasen der hergestellten Substanzen näher untersucht. Ein erster Untersuchungsgegenstand war das Dehnungsverhalten von freistehenden flüssigkristallinen Elastomerfilmen (LCE). Bei der Verwendung eines Polymers, in dem nur ein Teil des Polysiloxanrückgrats mit Seitengruppen substituiert ist, wird die uniaxiale Dehnung des Films parallel zu den smektischen Schichten durch eine gleichmäßige Kontraktion in der Filmebene und parallel zur Schichtnormalen ausgeglichen, was auf einen außergewöhnlich niedrigen smektischen Schichtkompressionsmodul zurückzuführen ist. Im Gegensatz dazu ist dieser Modul bei den Homopolymersystemen so groß, dass praktisch senkrecht zu den smektischen Schichten keine Kontraktion stattfindet. Ein zweiter Untersuchungsgegenstand der Netzwerkbildung bestand in der Bestimmung der dynamisch-mechanischen Eigenschaften der LC-Polysiloxane mittels eines Oszillationsrheometers. Hier erfolgten die Messungen von Speicher- und Verlustmodul in Abhängigkeit vom Polymerrückgrat und von der Vernetzung. Die unvernetzten Systeme zeigten in den smektischen Phasen (oberhalb Tg) noch – im wesentlichen – Festkörpereigenschaften (physikalische Vernetzung) mit einem dominierenden Speichermodul beim LC-Homopolysiloxan. Beim LC-Copolysiloxan haben beide Module eine gleiche Größenordnung. Am Phasenübergang in die isotrope Phase wurden beide Module absolut kleiner, der Verlustmodul aber relativ größer. In der isotropen Phase verhalten sich die LC-Polymere damit überwiegend wie viskose Schmelzen. Außerdem korrelierten die mittels DSC bestimmten Phasenübergangstemperaturen mit einer Änderung der dynamisch-mechanischen Eigenschaften. Nach der Vernetzung dominierte der Speichermodul sowohl beim LC-Homo- als auch beim LC-Copolysiloxan bis in die isotrope Phase, und es war aufgrund der Bildung einer festen Netzwerkstruktur keine Abhängigkeit der Module von Phasenübergängen mehr erkennbar. Als dritter Untersuchungsgegenstand wurde der Phasenübergang zwischen den beiden smektischen Phasen (SmC* nach SmA*) der flüssigkristallinen Polysiloxane näher behandelt. Als wichtigstes Ergebnis ist festzuhalten, dass die verdünnten LC-Polysiloxane an diesem Übergang fast keine Schichtdickenänderung aufweisen. Dazu wurde jeweils die röntgenographisch ermittelte Schichtdicke mit der aus den optischen Tiltwinkeln theoretisch berechneten Schichtdicke verglichen. Dadurch konnte gezeigt werden, dass sich die Phasenübergänge nach dem de Vries-Modell verhalten. Damit konnte zum ersten Mal an Polymersystemen ein de Vries-Verhalten nachgewiesen werden. Im Gegensatz dazu zeigte das Homopolysiloxan mit dem Dreiringmesogen beim Übergang von SmC* nach SmA* einen ausgeprägten Sprung in der Schichtdicke. Wie auch durch DSC-Messungen nachweisbar, lag ein Phasenübergang 1. Ordnung vor. Bei den LC-Copolysiloxanen liegt dagegen ein Phasenübergang 2. Ordnung vor. Schließlich wurde die Schichtdicke unter dem Einfluss der Vernetzung untersucht. Beim LC-Copolysiloxan mit dem Dreiringmesogen und einem Anteil an vernetzbaren Gruppen von 15 % wurde eine Stabilisierung der smektischen Phasen erreicht. Zum einen war die Änderung der Schichtdicke am SmC*-SmA*-Phasenübergang geringer im Vergleich zum unvernetzten System und zum anderen war noch 50 °C über der ursprünglichen Klärtemperatur eine smektische Schichtstruktur röntgenographisch nachzuweisen. Insgesamt ist es mit den verschiedenen Untersuchungsmethoden gelungen, einen systematischen Unterschied zwischen smektischen Homo- und Copolysiloxanen aufzuzeigen, der seinen Ursprung – aller Wahrscheinlichkeit nach – in der Mikrophasenseparation von Mesogenen und Polysiloxanketten findet.

Anisotrope Kolloide aus flüssigkristallinen Polymeren

In dieser Arbeit wird die Synthese, Charakterisierung und Manipulation anisotroper Kolloide aus flüssigkristallinen Polymeren beschrieben. Um Kolloide verschiedener Größe und aus verschiedenen Polymeren zu erhalten, wurden verschiedene Techniken verwendet. Einerseits wurden Kolloide aus nematischen und smektischen Polymeren mit Durchmessern meist im Bereich von 0,5 bis 3,5 Mikrometern hergestellt. Dazu wurden 16 verschiedene Acrylat- und Methacrylatmonomere synthetisiert und mittels Dispersionspolymerisation polymerisiert. Durch Variation der Polymerisationsbedingungen wurden Kolloide verschiedener Größe und Polydispersität erhalten. Durch Saatpolymerisation konnten zudem die Kugelgrößen bei gleichbleibend geringer Polydispersität erhöht werden. Polarisationsmikroskopie zeigt, dass die meisten Kolloide mit einer Größe zwischen ca. 2 bis 4 Mikrometern eine bipolare Direktorkonfiguration haben. Einige dieser Kolloide wurden mit einer optischen Pinzette mit zirkular polarisiertem Licht eingefangen und rotiert. Zum anderen wurden verschiedene flüssigkristalline Polymere (Polysiloxane, Hauptkettenpolymere und Polyacrylate) durch den Miniemulsionsprozess in Kolloide mit Durchmessern im Bereich von ca. 50 bis 300 nm überführt. Durch Variation der Emulgator- und Polymermenge sowie der Art des Emulgators konnte die Kugelgröße beeinflusst werden. Für die Polysiloxankolloide erfolgte die Aufklärung ihrer inneren Struktur mittels TEM und Kryo-TEM, da durch das Silizium im Polymerrückgrat ohne zusätzliches Anfärben ein Kontrast vorhanden ist. Die TEM-Aufnahmen zeigen deutlich die smektische Schichtstruktur innerhalb der Kolloide aus „verdünnten“ Copolysiloxanen und sind somit der erste direkte Beweis für die Mikrophasenseparation zwischen den Mesogenen und Polysiloxanketten, die bisher basierend auf Röntgenmessungen nur indirekt vorhergesagt wurde. Für die Copolysiloxane mit 2-Ring-Mesogenen wurden zwiebelartige Strukturen und für die Copolysiloxane mit 3-Ring-Mesogenen parallele Schichtstrukturen gefunden. Im ersten Fall folgt die smektische Schichtstruktur der Kugelsymmetrie des Kolloids, im zweiten Fall dominiert die Tendenz der smektischen Schichten, sich parallel anzuordnen.

Multilayer thin films by layer-by-layer (LBL) assembly of functional polyelectrolytes

Nanoscience aims at manipulating atoms, molecules and nano-size particles in a precise and controlled manner. Nano-scale control of the thin film structures of organic/polymeric materials is a prerequisite to the fabrication of sophisticated functional devices. The work presented in this thesis is a compilation of various polymer thin films with newly synthesized functional polymers. Cationic and anionic LC amphotropic polymers, p-type and n-type semiconducting polymers with triarylamine, oxadiazole, thiadiazole and triazine moieties are suitable materials to fabricate multilayers by layer-by-layer (LBL) self-assembly with a well defined internal structure. The LBL assembly is the ideal processing technique to prepare thin polymer film composites with fine control over morphology and composition at nano-scale thickness, which may have applications in photo-detectors, light-emitting diodes (LEDs), displays and sensors, as well as in solar cells. The multilayer build-up was investigated with amphotropic LC polymers individually by solution-dipping and spin-coating methods; they showed different internal orders with respect to layering and orientation of the mesogens, as a result of the liquid crystalline phase. The synthesized p-type and n-type semiconducting polymers were examined optically and electrochemically, suggesting that they are favorably promising as hole-(p-type) or electron-(n-type) transport materials in electronic and optoelectronic devices. In addition, we report a successful film deposition of polymers by the vacuum deposition method. The vapor deposition method provides a clean environment; it is solvent free and well suited to sequential depositions in hetero-structured multilayer system. As the potential applications, the fabricated polymer thin films were used as simple electrochromic films and also used as hole transporting layers in LEDs. Electrochemical and electrochromic characterizations of assembled films reveal that the newly synthesized polymers give rise to high contrast ratio and fast switching electrochromic films. The LEDs with vacuum deposited films show dramatic improvements in device characteristics, indicating that the films are promising as hole transporting layers. These are the result of not only the thin nano-scale film structures but also the combination with the high charge carrier mobility of synthesized semiconducting polymers.

Anisotrope Kolloide aus flüssigkristallinen Polymeren

In dieser Arbeit wurden Kolloide aus flüssigkristallinen Polymeren dargestellt und untersucht.rnrnDie Methode der Dispersionspolymerisation zur Darstellung von Kolloiden aus flüssigkristallinen Polyacrylaten wurde in unpolare Lösungsmittel adaptiert, umrneine Manipulierbarkeit anisotroper Kolloide durch elektrische Felder zu erreichen.rnDazu wurden ein Gemisch aus THF und Siliconöl als Reaktionsmischung gewähltrnund polysiloxanbasierte Polymere und Copolymere als Stabilisatoren eingesetzt.rnDabei auftretende unerwartete Auswirkungen auf die Mesogenkonfiguration führtenrnzu einer Untersuchung der Abhängigkeit der Mesogenkonfigurationen von der Oberflächenverankerung der Mesogene. Schließlich wurde eine Kontrolle derrnOberfl¨achenverankerung der Mesogene und somit eine Kontrolle der Mesogenkonfigurationen unter Ausnutzung der Eigenschaften flüssigkristallin/nicht flüssigkristalliner Blockcopolymere erreicht. Zu diesem Zweck wurde auch ein neuer Makroinitiator entwickelt. Kleine Kolloide konnten mittels eines elektrischen Feldes gedreht bzw. zu Linien angeordnet werden.rnrnEinige neue Polysiloxane wurden zum Einbau in flüssigkristalline Kolloide viarnMiniemulsion synthetisiert. Sie wurden charakterisiert und in Kolloide überführt. Aufgrund zu hoher Übergangstemperaturen konnten bei den meisten jedoch keine Strukturen aus phasenseparierten Polysiloxane gefunden werden. Die Ausbildung der Strukturen in solchen Kolloiden konnte aber trotzdem verstanden werden.rnrnAus vernetzten Hauptkettenpolymeren sollten aktuierende Kolloide hergestelltrnwerden. Dazu wurde das entsprechende Hauptkettenpolymer hergestellt, charakterisiert und per Miniemulsion in Kolloide überführt. Die dargestellten Kolloide wurden unter dem TEM geheizt und zeigten Formänderungen, die jedoch nicht kontrolliert und noch irreversibel waren.

Liquid crystal polymers: macromolecular design for enhanced performances

During this work, done mainly in the laboratories of the department of Industrial Chemistry and Materials of the University of Bologna but also in the laboratories of the Carnegie Mellon University in collaboration with prof. K. Matyjaszewski and at the university of Zaragoza in collaboration with prof. J. Barberá, was focused mainly on the synthesis and characterization of new functional polymeric materials. In the past years our group gained a deep knowledge about the photomodulation of azobenzene containing polymers. The aim of this thesis is to push forward the performances of these materials by the synthesis of well defined materials, in which, by a precise control over the macromolecular structures, better or even new functionality can be delivered to the synthesized material. For this purpose, besides the rich photochemistry of azoaromatic polymers that brings to the application, the control offered from the recent techniques of controlled radical polymerization, ATRP over all, gives an enormous range of opportunity for the developing of a new generation of functional materials whose properties are determinate not only by the chemical nature of the functional center (e.g. azoaromatic chromophore) but are tuned and even amplified by a synergy with the whole macromolecular structure. Old materials in new structures. In this contest the work of this thesis was focused mainly on the synthesis and characterization of well defined azoaromatic polymers in order to establish, for the first time, precise structure-properties correlation. In fact a series of well defined different azopolymers, chiral and achiral, with different molecular weight and highly monodisperse were synthesized and their properties were studied, in terms of photoexpansion and photomodulation of chirality. We were then able to study the influence of the macromolecular structure in terms of molecular weight and ramification on the studied properties. The huge amount of possibility offered by the tailoring of the macromolecular structure were exploited for the synthesis of new cholesteric photochromic polymers that can be used as a smart label for the certification of the thermal history of any thermosensitive product. Finally the ATRP synthesis allowed us to synthesize a total new class of material, named molecular brushes: a flat surface covered with an ultra thin layer of polymeric chain covalently bond onto the surface from one end. This new class of materials is of extreme interest as they offer the possibility to tune and manage the interaction of the surface with the environment. In this contest we synthesized both azoaromatic surfaces, growing directly the polymer from the surface, and mixed brushes: surfaces covered with incompatible macromolecules. Both type of surfaces acts as “smart” surfaces: the first it is able to move the orientation of a LC cell by simply photomodulation and, thanks to the robustness of the covalent bond, can be used as a command surface overcoming all the limitation due to the dewetting of the active layer. The second type of surface, functionalized by a grafting-to method, can self assemble the topmost layer responding to changed environmental conditions, exposing different functionality according to different environment.

Synthesis of Macrocyclic Polymers Formed via Intramolecular Radical Trap-Assisted Atom Transfer Radical Coupling

The synthesis of cyclic polystyrene (Pst) with an alkoxyamine functionality has been accomplished by intramolecular radical coupling in the presence of a nitroso radical trap Linear alpha,omega-dibrominated polystyrene, produced by the atom transfer radical polymerization (ATRP) of styrene using a dibrominated initiator, was subjected to chain-end activation via the atom transfer radical coupling (ATRC) process under pseudodilute conditions in the presence of 2-methyl-2-nitrosopropane (MNP). This radical trap-assisted, intramolecular ATRC (RTA-ATRC) produced cyclic polymers in greater than 90% yields possessing < G > values in the 0.8-0.9 range as determined by gel permeation chromatography (GPC). Thermal-induced opening of the cycles, made possible by the incorporated alkoxyamine, resulted in a return to the original apparent molecular weight, further supporting the formation of cyclic polymers in the RTA-ATRC reaction. Liquid chromatography-mass spectrometry (LC-MS) provided direct confirmation of the cyclic architecture and the incorporation of the nitroso group into the macrocycle RTA-ATRC cyclizations carried out with faster rates of polymer addition into the redox active solution and/or in the presence of a much larger excess of MNP (up to a 250:1 ratio of MNP:C-Br chain end) still yielded cyclic polymers that contained alkoxyamine functionality.

A study of methods used to analyze total oil and polycyclic aromatic hydrocarbons in produced water: steps towards the validation of molecularly imprinted polymers for use in marine environmetns

Produced water is a by-product of offshore oil and gas production, and is released in large volumes when platforms are actively processing crude oil. Some pollutants are not typically removed by conventional oil/water separation methods and are discharged with produced water. Oil and grease can be found dispersed in produced water in the form of tiny droplets, and polycyclic aromatic hydrocarbons (PAHs) are commonly found dissolved in produced water. Both can have acute and chronic toxic effects in marine environments even at low exposure levels. The analysis of the dissolved and dispersed phases are a priority, but effort is required to meet the necessary detection limits. There are several methods for the analysis of produced water for dispersed oil and dissolved PAHs, all of which have advantages and disadvantages. In this work, EPA Method 1664 and APHA Method 5520 C for the determination of oil and grease will be examined and compared. For the detection of PAHs, EPA Method 525 and PAH MIPs will be compared, and results evaluated. APHA Method 5520 C Partition-Infrared Method is a liquid-liquid extraction procedure with IR determination of oil and grease. For analysis on spiked samples of artificial seawater, extraction efficiency ranged from 85 – 97%. Linearity was achieved in the range of 5 – 500 mg/L. This is a single-wavelength method and is unsuitable for quantification of aromatics and other compounds that lack sp³-hybridized carbon atoms. EPA Method 1664 is the liquid-liquid extraction of oil and grease from water samples followed by gravimetric determination. When distilled water spiked with reference oil was extracted by this procedure, extraction efficiency ranged from 28.4 – 86.2%, and %RSD ranged from 7.68 – 38.0%. EPA Method 525 uses solid phase extraction with analysis by GC-MS, and was performed on distilled water and water from St. John’s Harbour, all spiked with naphthalene, fluorene, phenanthrene, and pyrene. The limits of detection in harbour water were 0.144, 3.82, 0.119, and 0.153 g/L respectively. Linearity was obtained in the range of 0.5-10 g/L, and %RSD ranged from 0.36% (fluorene) to 46% (pyrene). Molecularly imprinted polymers (MIPs) are sorbent materials made selective by polymerizing functional monomers and crosslinkers in the presence of a template molecule, usually the analytes of interest or related compounds. They can adsorb and concentrate PAHs from aqueous environments and are combined with methods of analysis including GC-MS, LC-UV-Vis, and desorption electrospray ionization (DESI)- MS. This work examines MIP-based methods as well as those methods previously mentioned which are currently used by the oil and gas industry and government environmental agencies. MIPs are shown to give results consistent with other methods, and are a low-cost alternative improving ease, throughput, and sensitivity. PAH MIPs were used to determine naphthalene spiked into ASTM artificial seawater, as well as produced water from an offshore oil and gas operation. Linearity was achieved in the range studied (0.5 – 5 mg/L) for both matrices, with R² = 0.936 for seawater and R² = 0.819 for produced water. The %RSD for seawater ranged from 6.58 – 50.5% and for produced water, from 8.19 – 79.6%.

Thermodynamic Study Of The Micellization Of Zwitterionic Surfactants And Their Interaction With Polymers In Water By Isothermal Titration Calorimetry.

The micellization of a homologous series of zwitterionic surfactants, a group of sulfobetaines, was studied using isothermal titration calorimetry (ITC) in the temperature range from 15 to 65 °C. The increase in both temperature and the alkyl chain length leads to more negative values of ΔGmic(0) , favoring the micellization. The entropic term (ΔSmic(0)) is predominant at lower temperatures, and above ca. 55-65 °C, the enthalpic term (ΔHmic(0)) becomes prevalent, figuring a jointly driven process as the temperature increases. The interaction of these sulfobetaines with different polymers was also studied by ITC. Among the polymers studied, only two induced the formation of micellar aggregates at lower surfactant concentration: poly(acrylic acid), PAA, probably due to the formation of hydrogen bonds between the carboxylic group of the polymer and the sulfonate group of the surfactant, and poly(sodium 4-styrenesulfonate), PSS, probably due to the incorporation of the hydrophobic styrene group into the micelles. The prevalence of the hydrophobic and not the electrostatic contributions to the interaction between sulfobetaine and PSS was confirmed by an increased interaction enthalpy in the presence of electrolytes (NaCl) and by the observation of a significant temperature dependence, the latter consistent with the proposed removal of hydrophobic groups from water.

Triboelectricity In Insulating Polymers: Evidence For A Mechanochemical Mechanism.

Transfer of reaction products formed on the surfaces of two mutually rubbed dielectric solids makes an important if not dominating contribution to triboelectricity. New evidence in support of this statement is presented in this report, based on analytical electron microscopy coupled to electrostatic potential mapping techniques. Mechanical action on contacting surface asperities transforms them into hot-spots for free-radical formation, followed by electron transfer producing cationic and anionic polymer fragments, according to their electronegativity. Polymer ions accumulate creating domains with excess charge because they are formed at fracture surfaces of pulled-out asperities. Another factor for charge segregation is the low polymer mixing entropy, following Flory and Huggins. The formation of fractal charge patterns that was previously described is thus the result of polymer fragment fractal scatter on both contacting surfaces. The present results contribute to the explanation of the centuries-old difficulties for understanding the triboelectric series and triboelectricity in general, as well as the dissipative nature of friction, and they may lead to better control of friction and its consequences.

Polímeros biomiméticos em química analítica. Parte 1: preparo e aplicações de MIP (Molecularly Imprinted Polymers) em técnicas de extração e separação

MIPs are synthetic polymers that are used as biomimetic materials simulating the mechanism verified in natural entities such as antibodies and enzymes. Although MIPs have been successfully used as an outstanding tool for enhancing the selectivity or different analytical approaches, such as separation science and electrochemical and optical sensors, several parameters must be optimized during their synthesis. Therefore, the state-of-the-art of MIP production as well as the different polymerization methods are discussed. The potential selectivity of MIPs in the extraction and separation techniques focusing mainly on environmental, clinical and pharmaceutical samples as applications for analytical purposes is presented.

Polímeros biomiméticos em química analítica. Parte 2: aplicações de MIP (Molecularly Imprinted Polymers) no desenvolvimento de sensores químicos

The aim of this paper is the description of the strategies and advances in the use of MIP in the development of chemical sensors. MIP has been considered an emerging technology, which allows the synthesis of materials that can mimic some highly specific natural receptors such as antibodies and enzymes. In recent years a great number of publications have demonstrated a growth in their use as sensing phases in the construction of sensors . Thus, the MIP technology became very attractive as a promising analytical tool for the development of sensors.

On-line identification of minor flavones from sugarcane juice by LC/UV/MS and post-column derivatization

This work describes the on-line characterization of minor flavones from sugarcane (Saccharum officinarum) juice by high-performance liquid chromatography coupled to diode array UV detection and mass spectrometry (LC/UV/MS) using atmospheric pressure chemical ionization-collision-induced dissociation (APCI-CID-MS/MS) and post-column derivatization using UV shift reagents. HPLC-UV analysis with shift reagents provided information about the substitution pattern in the flavonoid skeleton and, combined with MS data, these techniques allowed for the on-line identification of five "garapa" flavones: luteolin-8-C-glucosyl-7-O-glucuronide; tricin-7-O-neohesperoside-4'-O-rhamnoside; tricin-7-O-methylglucuronate-4'-O-rhamnoside; tricin-7-O-methylglucuronide; swertisin, while four other compounds were partially identified as glycosylflavones. Only swertisin (7-O-methylapigenin-6-C-glucoside) was reported previously in sugarcane molasses.