Gap acceptance behavior of mobile phone distracted drivers at roundabouts

While mobile phones have become ubiquitous in modern society, the use of mobile phones while driving is increasing at an alarming rate despite the associated crash risks. A significant safety concern is that driving while distracted by a mobile phone is more prevalent among young drivers, a less experienced driving cohort with elevated crash risk. The objective of this study was to examine the gap acceptance behavior of distracted young drivers at roundabouts. The CARRS-Q Advanced Driving Simulator was used to test participants on a simulated gap acceptance scenario at roundabouts. Conflicting traffic from the right approach of a four-legged roundabout were programmed to have a series of vehicles having the gaps between them proportionately increased from two to six seconds. Thirty-two licensed young drivers drove the simulator under three phone conditions: baseline (no phone conversation), hands-free and handheld phone conversations. Results show that distracted drivers started responding to the gap acceptance scenario at a distance closer to the roundabout and approached the roundabout at slower speeds. They also decelerated at faster rates to reduce their speeds prior to gap acceptance compared to non-distracted drivers. Although accepted gap sizes were not significantly different across phone conditions, differences in the safety margins at various gap sizes—measured by Post Encroachment Time (PET) between the driven vehicle and the conflicting vehicle—were statistically significant across phone conditions. PETs for distracted drivers were smaller across different gap sizes, suggesting a lower safety margin taken by distracted drivers compared to non-distracted drivers. The results aid in understanding how cognitive distraction resulting from mobile phone conversations while driving influences driving behavior during gap acceptance at roundabouts.

Critical gap estimation by numerical and statistical highest likelihood search

Many traffic situations require drivers to cross or merge into a stream having higher priority. Gap acceptance theory enables us to model such processes to analyse traffic operation. This discussion demonstrated that numerical search fine tuned by statistical analysis can be used to determine the most likely critical gap for a sample of drivers, based on their largest rejected gap and accepted gap. This method shares some common features with the Maximum Likelihood Estimation technique (Troutbeck 1992) but lends itself well to contemporary analysis tools such as spreadsheet and is particularly analytically transparent. This method is considered not to bias estimation of critical gap due to very small rejected gaps or very large rejected gaps. However, it requires a sufficiently large sample that there is reasonable representation of largest rejected gap/accepted gap pairs within a fairly narrow highest likelihood search band.

Novel methods and the maximum likelihood estimation technique for estimating traffic critical gap

Most unsignalised intersection capacity calculation procedures are based on gap acceptance models. Accuracy of critical gap estimation affects accuracy of capacity and delay estimation. Several methods have been published to estimate drivers’ sample mean critical gap, the Maximum Likelihood Estimation (MLE) technique regarded as the most accurate. This study assesses three novel methods; Average Central Gap (ACG) method, Strength Weighted Central Gap method (SWCG), and Mode Central Gap method (MCG), against MLE for their fidelity in rendering true sample mean critical gaps. A Monte Carlo event based simulation model was used to draw the maximum rejected gap and accepted gap for each of a sample of 300 drivers across 32 simulation runs. Simulation mean critical gap is varied between 3s and 8s, while offered gap rate is varied between 0.05veh/s and 0.55veh/s. This study affirms that MLE provides a close to perfect fit to simulation mean critical gaps across a broad range of conditions. The MCG method also provides an almost perfect fit and has superior computational simplicity and efficiency to the MLE. The SWCG method performs robustly under high flows; however, poorly under low to moderate flows. Further research is recommended using field traffic data, under a variety of minor stream and major stream flow conditions for a variety of minor stream movement types, to compare critical gap estimates using MLE against MCG. Should the MCG method prove as robust as MLE, serious consideration should be given to its adoption to estimate critical gap parameters in guidelines.

Estimating the mean critical gap

The estimation of the critical gap has been an issue since the 1970s, when gap acceptance was introduced to evaluate the capacity of unsignalized intersections. The critical gap is the shortest gap that a driver is assumed to accept. A driver’s critical gap cannot be measured directly and a number of techniques have been developed to estimate the mean critical gaps of a sample of drivers. This paper reviews the ability of the Maximum Likelihood technique and the Probability Equilibrium Method to predict the mean and standard deviation of the critical gap with a simulation of 100 drivers, repeated 100 times for each flow condition. The Maximum Likelihood method gave consistent and unbiased estimates of the mean critical gap. Whereas the probability equilibrium method had a significant bias that was dependent on the flow in the priority stream. Both methods were reasonably consistent, although the Maximum Likelihood Method was slightly better. If drivers are inconsistent, then again the Maximum Likelihood method is superior. A criticism levelled at the Maximum Likelihood method is that a distribution of the critical gap has to be assumed. It was shown that this does not significantly affect its ability to predict the mean and standard deviation of the critical gaps. Finally, the Maximum Likelihood method can predict reasonable estimates with observations for 25 to 30 drivers. A spreadsheet procedure for using the Maximum Likelihood method is provided in this paper. The PEM can be improved if the maximum rejected gap is used.

Microscopic modelling of freeway operations

Freeways are divided roadways designed to facilitate the uninterrupted movement of motor vehicles. However, many freeways now experience demand flows in excess of capacity, leading to recurrent congestion. The Highway Capacity Manual (TRB, 1994) uses empirical macroscopic relationships between speed, flow and density to quantify freeway operations and performance. Capacity may be predicted as the maximum uncongested flow achievable. Although they are effective tools for design and analysis, macroscopic models lack an understanding of the nature of processes taking place in the system. Szwed and Smith (1972, 1974) and Makigami and Matsuo (1990) have shown that microscopic modelling is also applicable to freeway operations. Such models facilitate an understanding of the processes whilst providing for the assessment of performance, through measures of capacity and delay. However, these models are limited to only a few circumstances. The aim of this study was to produce more comprehensive and practical microscopic models. These models were required to accurately portray the mechanisms of freeway operations at the specific locations under consideration. The models needed to be able to be calibrated using data acquired at these locations. The output of the models needed to be able to be validated with data acquired at these sites. Therefore, the outputs should be truly descriptive of the performance of the facility. A theoretical basis needed to underlie the form of these models, rather than empiricism, which is the case for the macroscopic models currently used. And the models needed to be adaptable to variable operating conditions, so that they may be applied, where possible, to other similar systems and facilities. It was not possible to produce a stand-alone model which is applicable to all facilities and locations, in this single study, however the scene has been set for the application of the models to a much broader range of operating conditions. Opportunities for further development of the models were identified, and procedures provided for the calibration and validation of the models to a wide range of conditions. The models developed, do however, have limitations in their applicability. Only uncongested operations were studied and represented. Driver behaviour in Brisbane was applied to the models. Different mechanisms are likely in other locations due to variability in road rules and driving cultures. Not all manoeuvres evident were modelled. Some unusual manoeuvres were considered unwarranted to model. However the models developed contain the principal processes of freeway operations, merging and lane changing. Gap acceptance theory was applied to these critical operations to assess freeway performance. Gap acceptance theory was found to be applicable to merging, however the major stream, the kerb lane traffic, exercises only a limited priority over the minor stream, the on-ramp traffic. Theory was established to account for this activity. Kerb lane drivers were also found to change to the median lane where possible, to assist coincident mergers. The net limited priority model accounts for this by predicting a reduced major stream flow rate, which excludes lane changers. Cowan's M3 model as calibrated for both streams. On-ramp and total upstream flow are required as input. Relationships between proportion of headways greater than 1 s and flow differed for on-ramps where traffic leaves signalised intersections and unsignalised intersections. Constant departure onramp metering was also modelled. Minimum follow-on times of 1 to 1.2 s were calibrated. Critical gaps were shown to lie between the minimum follow-on time, and the sum of the minimum follow-on time and the 1 s minimum headway. Limited priority capacity and other boundary relationships were established by Troutbeck (1995). The minimum average minor stream delay and corresponding proportion of drivers delayed were quantified theoretically in this study. A simulation model was constructed to predict intermediate minor and major stream delays across all minor and major stream flows. Pseudo-empirical relationships were established to predict average delays. Major stream average delays are limited to 0.5 s, insignificant compared with minor stream delay, which reach infinity at capacity. Minor stream delays were shown to be less when unsignalised intersections are located upstream of on-ramps than signalised intersections, and less still when ramp metering is installed. Smaller delays correspond to improved merge area performance. A more tangible performance measure, the distribution of distances required to merge, was established by including design speeds. This distribution can be measured to validate the model. Merging probabilities can be predicted for given taper lengths, a most useful performance measure. This model was also shown to be applicable to lane changing. Tolerable limits to merging probabilities require calibration. From these, practical capacities can be estimated. Further calibration is required of traffic inputs, critical gap and minimum follow-on time, for both merging and lane changing. A general relationship to predict proportion of drivers delayed requires development. These models can then be used to complement existing macroscopic models to assess performance, and provide further insight into the nature of operations.

Analisi di modelli teorico-empirici di capacità per le intersezioni a rotatoria

In questa tesi di laurea si affronta l’analisi di diversi modelli per il calcolo della capacità di un’intersezione a rotatoria: alcuni di questi sono di tipo empirico, altri invece sono di tipo teorico (teoria del gap acceptance). Innanzitutto si descrivono le caratteristiche di tutti i modelli studiati e si esaminano i risultati ottenuti nel calcolo della capacità al variare del flusso circolante, effettuato su un campione di venti rotatorie. In particolare si cerca di confrontare tra loro i vari modelli e di interpretare il significato dei parametri che compaiono nelle diverse formule. Successivamente si amplia l’analisi, utilizzando i dati raccolti come punto di partenza per una serie di altre elaborazioni ed interpolazioni. Alla base di questa seconda parte dello studio c’è l’idea di provare a vedere se sia possibile ricavare un nuovo modello, derivante da quelli studiati, che possa riassumerli in maniera semplice e aiutare a chiarire quali sono i parametri più importanti dai quali dipende il valore di capacità di una rotatoria. Questo nuovo modello dovrebbe eventualmente servire più che altro per interpretare i modelli studiati e per capire se uno di questi si comporti meglio degli altri in situazioni particolari oppure se sia più adatto in determinate condizioni di traffico piuttosto che in altre. Uno degli obiettivi principali di questo studio è infatti quello di provare a capire se la capacità di una rotatoria è influenzata maggiormente da aspetti geometrici, legati quindi alla forma e alle dimensioni della rotatoria stessa, oppure se un ruolo predominante è svolto da fattori comportamentali, legati quindi all’interazione tra i veicoli e ai processi di scelta degli utenti, che devono decidere se immettersi o meno nella rotatoria.

Examination of intersection, left turn across path crashes and potential IVHS countermeasures. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Development and use of a computer simulation model for the evaluation of design and control alternatives for intersections of minor roads with multi-lane rural highways: field studies and model validation. Interim report.

Federal Highway Administration, Washington, D.C.

Development and use of a computer simulation model for the evaluation of design and control alternatives for intersections of minor roads with multi-lane rural highways: model application. Interim report.

Federal Highway Administration, Washington, D.C.

Development and use of a computer simulation model for the evaluation of design and control alternatives for intersections of minor roads with multi-lane rural highways: selection of the simulation model. Interim report.

Federal Highway Administration, Washington, D.C.

Identification of unsafe driving actions and related countermeasures. Final report.

National Highway Traffic Safety Administration, Office of Driver and Pedestrian Research, Washington, D.C.

An investigation of consumer acceptance of M-Banking in Australia

Mobile phone banking (M-Banking) adoption around the world has been slow, and this has been perpetuated by the limited research that has been undertaken in the area. To address this gap, the study developed a model of antecedents to consumers' intention to sue M-Banking using attitudinal theory as a framework. To test the model, a quantitative web-based survey was undertaken with 314 respondents. The findings show that perceived usefulness, compatibility, perceived risk, perceived cost and attitude are primary determinants of consumer acceptance of M-Banking in an Australian context, The research contributes to an enhanced understanding of the multiple antecedents beliefs to customer attitudes and usage intentions that must be considered when introducing technology into the service encounter.

Bridging the gap : developing an innovative online resource for international graduate students

This paper describes the development of an innovative online website for international graduate students studying at universities in Australia. In 2008, the Queensland University of Technology (QUT) in Australia identified as a key goal the development of its profile as a research intensive university. One of the performance indicators in realising this goal was to increase the proportion of international graduate students from 20% to 50% over a five-year period. To support these students, the University Research Students Centre (RSC) decided to develop an innovative interactive website called the ‘Doorway to Research’ to help prepare students for their arrival in Australia, by providing access to information and support between the period of their acceptance to their graduate programs and their arrival into the country.

Public acceptance towards congestion charge : a case study of Brisbane

This paper investigates public acceptance towards congestion charge in Australia by taking Brisbane as a case study. Public acceptance to congestion charge has often been investigated in the literature. However, few were in the context of an Australian city. This paper fills the gap. A face-to-face survey was conducted to solicit public opinions on the congestion charge, should a congestion charge scheme be implemented in the Brisbane City area. The survey data were analysed to pinpoint important factors relevant to people’s attitudes towards congestion charge and to measure their relationships. Main findings from our analysis are: (1) the residents’ attitudes towards congestion charge differ by genders and by user groups of transport modes; (2) for each of the three groups (i.e., the auto users, the transit riders, and the whole participants), a positive and stable correlation was found between a participant’s attitude towards congestion charge and the effectiveness of congestion charge on reducing traffic congestion. A negative and stable correlation was also found for all three groups between a participant’s attitude towards congestion charge and congestion charge’s negative impact on the attractiveness of working in the city; (3) the auto users tended to be more sceptical about the service capacity of existing transit systems in coping with extra passengers induced by the implementation of congestion charge; and (4) for people with high income, introducing the congestion charge may have no impact on their travelling to the city.