Electrochemical promotion of a platinum catalyst supported on the high-temperature proton conductor La0.99Sr0.01NbO4-δ

The recently discovered, high-temperature proton conductor, La_0.99Sr_0.01NbO_4-δ, was used as a support for the electrochemical promotion of a platinum catalyst. Ethylene oxidation was used as a probe reaction in the temperature range 350-450 °C. Moderate non-Faradaic rate modification, attributable to a protonic promoting species, occurred under negative polarisation; some permanent promotion was also observed. In oxidative atmospheres, both the p_O2 of the reaction mixture and the temperature influenced the type and magnitude of the observed rate modification. Rate-enhancement values of up to ρ = 1.4 and Faradaic-efficiency values approaching Λ = -100 were obtained. Promotion was observed under positive polarisation and relatively dry, oxygen-rich atmospheres suggesting that some oxygen ion conductivity may occur under these conditions. Impedance spectroscopy performed in atmospheres of 4 kPa O₂/N₂ and of 5 kPa H₂/N₂ under dry and slightly humidified (0.3 kPa H₂O) conditions indicated that the electrical resistivity is heavily dominated by the grain-boundary response in the temperature range of the EPOC studies; much lower grain-boundary impedances in the wetter conditions are likely to be attributable to proton transport. © 2009 Elsevier B.V. All rights reserved.

(PEG)(x)NH4ClO4: A new polymeric fast proton conductor

A new polymer electrolyte (PEG)(x) NH4ClO4(x = 5, 10, 15, 20) has been prepared that shows protonic conduction. The room temperature conductivities are of the order of 10(-7) S/cm, and increase with decrease in salt concentration. NMR line width studies indicate fairly low glass transition temperatures of the polymer salt complexes.

Magnetic resonance and conductivity study of gelatin-based proton conductor polymer electrolytes

This work report results from proton nuclear magnetic resonance (NMR), continuous-wave (CW-EPR) and pulsed electron paramagnetic resonance (P-EPR) and complex impedance spectroscopy of gelatin-based polymer gel electrolytes containing acetic acid. cross-linked with formaldehyde and plasticized with glycerol. Ionic conductivity of 2 x 10(-5) S/cm was obtained at room temperature for samples prepared with 33 wt% of acetic acid. Proton ((1)H) line shapes and spin-lattice relaxation times were measured as a function of temperature. The NMR results show that the proton mobility is dependent on acetic acid content in the plasticized polymer gel electrolytes. The CW-EPR spectra, which were carried out in samples doped with copper perchlorate, indicate the presence of the paramagnetic Cu(2+) ions in axially distorted sites. The P-EPR technique, known as electron spin echo envelope modulation (ESEEM), was employed to show the involvement of both, hydrogen and nitrogen atoms, in the copper complexation of the gel electrolyte. (C) 2009 Elsevier Ltd. All rights reserved.

Characterization of a proton conductor based on silicotungstic acid

It was found in this work that silicotungstic acid hydrate could be mixed with phosphoric acid (H₃PO₄, 85%) to make a viscous paste material with high conductivity (10⁻² S/cm at room temperature). The STA/H₃PO₄ paste samples were stable at 80°C in the atmosphere, and at 100°C under constant humidity over 10 days. The conductivity behavior of the paste samples has been investigated under various conditions, and it was found to be dependent on temperature, paste composition, and environment humidity.

Electrical relaxation in proton conductor composites based on (NH4)H2PO4/TiO2

We report on electrical relaxation measurements of (1-x)NH4H2PO4-xTiO(2) (x = 0.1) composites by admittance spectroscopy, in the 40-Hz-5-MHz frequency range and at temperatures between 303 and 563 K. Simultaneous thermal and electrical measurements on the composites identify a stable crystalline phase between 373 and 463 K. The real part of the conductivity, sigma', shows a power-law frequency dependence below 523 K, which is well described by Jonscher's expression sigma' = sigma(0)(1 + (omega/omega(p))(n)), where sigma(0) is the dc conductivity, omega(p)/2 pi = f(p) is a characteristic relaxation frequency, and n is a fractional exponent between 0 and 1. Both sigma(0) and f(p) are thermally activated with nearly the same activation energy in the II region, indicating that the dispersive conductivity originates from the migration of protons. However, activation energies decrease from 0.55 to 0.35 eV and n increases toward 1.0, as the concentration of TiO2 nanoparticles increases, thus, enhancing cooperative correlation among moving ions. The highest dc conductivity is obtained for the composite x = 0.05 concentration, with values above room temperature about three orders of magnitude higher than that of crystalline NH4H2PO4 (ADP), reaching values on the order of 0.1 (Omega cm)(-1) above 543 K.

Sinteractivity, proton conductivity and chemical stability of BaZr 0.7In0.3O3-δ for solid oxide fuel cells (SOFCs)

In3+ was used as dopant for BaZrO3 proton conductor and 30 at%-doped BaZrO3 samples (BaZr0.7In 0.3O3-δ, BZI) were prepared as electrolyte materials for proton-conducting solid oxide fuel cells (SOFCs). The BZI material showed a much improved sinteractivity compared with the conventional Y-doped BaZrO 3. The BZI pellets reached almost full density after sintering at 1600 °C for 10 h, whereas the Y-doped BaZrO3 samples still remained porous under the same sintering conditions. The conductivity measurements indicated that BZI pellets showed smaller bulk but improved grain boundary proton conductivity, when compared with Y-doped BaZrO3 samples. A total proton conductivity of 1.7 × 10-3 S cm -1 was obtained for the BZI sample at 700 °C in wet 10% H 2 atmosphere. The BZI electrolyte material also showed adequate chemical stability against CO2 and H2O, which is promising for application in fuel cells.

Electrochemical promotion of a metal catalyst supported on a mixed-ionic conductor

It has been found that the catalytic activity and selectivity of a metal film deposited on a solid electrolyte could be enhanced dramatically and in a reversible way by applying an electrical current or potential between the metal catalyst and the counter electrode (also deposited on the electrolyte). This phenomenon is know as NEMCA [S. Bebelis, C.G. Vayenas, Journal of Catalysis, 118 (1989) 125-146.] or electrochemical promotion (EP) [J. Prichard, Nature, 343 (1990) 592.] of catalysis. Yttria-doped barium zirconate, BaZr_0.9Y_0.1O_{3 - α} (BZY), a known proton conductor, has been used in this study. It has been reported that proton conducting perovskites can, under the appropriate conditions, act also as oxide ion conductors. In mixed conducting systems the mechanism of conduction depends upon the gas atmosphere that to which the material is exposed. Therefore, the use of a mixed ionic (oxide ion and proton) conducting membrane as a support for a platinum catalyst may facilitate the tuning of the promotional behaviour of the catalyst by allowing the control of the conduction mechanism of the electrolyte. The conductivity of BZY under different atmospheres was measured and the presence of oxide ion conduction under the appropriate conditions was confirmed. Moreover, kinetic experiments on ethylene oxidation corroborated the findings from the conductivity measurements showing that the use of a mixed ionic conductor allows for the tuning of the reaction rate. © 2006 Elsevier B.V. All rights reserved.

Electrochemical promotion of catalysis using solid-state proton-conducting membranes

A solid-state electrochemical reactor with ceramic proton-conducting membrane has been used to study the effect of electrochemically induced hydrogen spillover on the catalytic activity of platinum during ethylene oxidation. Suitable proton-conducting electrolyte membranes (Gd-doped BaPrO ₃ (BPG) and Y-doped BaZrO₃ (BZY)) were fabricated. These materials were chosen because of their protonic conductivity in the operational temperature region of the reaction (400-700 °C). The BZY-based electrochemical cell was used to investigate the open-circuit voltage (OCV) dependence on H₂ partial pressure with comparison being made to the theoretical OCV as predicted by the Nernst equation. Furthermore, the BZY pellets were used to study the effect of proton transfer of the catalytic activity of platinum during ethylene oxidation. The reaction was found to exhibit electrochemical promotion at 400 °C and to be electrophilic in nature, i.e. proton addition to the platinum surface resulted in an increase in reaction rate. At higher temperatures, the rate was not affected, within experimental error, by proton addition or removal. Under similar conditions, AC impedance showed that there was a large overall cell resistance at 400 °C with significantly decreased resistance at higher temperatures. It is possible that there could be a relationship between large cell resistances and the onset of electrochemical promotion in this system but there is, as yet, no conclusive evidence for this. © 2003 Elsevier B.V. All rights reserved.

A new class of proton-conducting ionic plastic crystals based on organic cations and dihydrogen phosphate

Choline dihydrogen phosphate ([N_1.1.1.2OH]DHP) and 1-butyl-3-methylimidazolium dihydrogen phosphate ([C₄mim]DHP) were synthesized as a new class of proton-conducting ionic plastic crystals. Both [N_1.1.1.2OH]DHP and [C₄mim]DHP showed solid–solid phase transition(s) and showed a final entropy of fusion lower than 20 J K⁻¹ mol⁻¹ which is consistent with Timmerman’s criterion for molecular plastic crystals. The ionic conductivity of [N_1.1.1.2OH]DHP was in the range of 10⁻⁶ S cm⁻¹–10⁻³ S cm⁻¹ in the plastic crystalline phase. On the other hand, the ionic conductivity of [C₄mim]DHP showed about 10⁻⁵ S cm⁻¹ in the plastic crystalline phase. [N_1.1.1.2OH]DHP showed one order of magnitude higher ionic conductivity than [C₄mim]DHP in the temperature range where the plastic phase is stable.

NMR and conductivity study of the protonic conductor HPb2Nb3O10 center dot nH(2)O

Electrical conductivity and H-1 Nuclear Magnetic Resonance (NMR) techniques were used to investigate the ion-exchanged layered lead-niobate perovskite HPb2Nb3O10. nH(2)O, over the temperature range 90-350 K. Compounds were synthesized by the sol-gel method and calcinated at 650 degreesC. Analysis of the NMR data gives activation energies for the proton motion in the range 0.14-0.40 eV, which are dependent on the water content. The frequency and temperature dependencies of the proton spin-lattice relaxation times show that the character of the motion of the: water molecules is essentially two-dimensional, reflecting the layered structure of the material. The H-1 line-narrowing transition and the single spin-lattice relaxation rate maximum, observed in the hydrated compounds, are consistent with a Grotthuss-like mechanism for the proton diffusion. (C) 2000 Elsevier B.V. B.V. All rights reserved.

Phosphonic acid-containing molecules as proton conductors and linkers for hybrid materials

In dieser Arbeit werden zwei Arten von nicht-kovalent verknüpften Netzwerkstrukturen vorgestellt, die aus phosphonsäurehaltigen Molekülen aufgebaut sind. Einerseits sollen diese phosphonsäurehaltigen Moleküle als Protonenleiter in Brennstoffzellen eingesetzt werden. Dies ist durch die Möglichkeit des kooperativen Protonentransports in wasserstoffbrückenhaltigen Netzwerken begründet. Auf der anderen Seite sollen die phosphonsäurehaltigen Moleküle unter Einsatz von Metallkationen zur Darstellung ionischer Netzwerke verwendet werden. In diesem Fall fungieren die phosphonierten Moleküle als Linker in porösen organisch-anorganischen Hybridmaterialien, die sich beispielsweise zur Gasspeicherung eignen.rnEine Brennstoffzelle stellt Energie mit hoher Effizienz und geringer Umweltbelastung bereit. Das Herzstück der Brennstoffzelle ist die Elektrolytmembran, die auch als Separator oder Protonenaustauschmembran (PEM) bezeichnet wird. Es wird davon ausgegangen, daß der Schlüssel zur Weiterentwicklung der PEM-Brennstoffzellen in der Entwicklung von Elektrolyten liegt, die ausschließlich und effizient Protonen transportieren und darüber hinaus chemisch (oxidationsbeständig) und mechanisch stabil sind. Die mechanische Stabilität betrifft insbesondere den Betrieb der Brennstoffzelle bei hohen Temperaturen und niedriger relativer Feuchtigkeit. In dieser Arbeit wird ein neuartiger Ansatz zum Erreichen eines hohen Protonentransports im Festkörper vorgestellt, der auf dem Einsatz kleiner Moleküle beruht, die durch Selbstorganisation eine kontinuierliche protonenleitende Phase erzeugen. Bis jetzt stellt Hexakis(p-phosphonatophenyl)benzol das erste Beispiel eines kristallinen Protonenleiters dar, der im festen Zustand eine hohe und konstante Leistung zeigt. Die Modifizierung von Hexakis(p-phosphonatophenyl)benzol, entweder durch Änderung von para- zu meta-Substitution oder die Einführung von Alkylketten, führt zu Verbindungen geringerer Kristallinität und niedriger Protonenleitfähigkeit.rnIm zweiten Teil der Arbeit wurde 1,3,5-Tris(p-phosphonatophenyl)benzol als Linker in der Synthese von offenen Phosphonat-Netzwerken eingesetzt. Es bilden sich aufgrund der ionischen Wechselwirkung zwischen den positiv geladenen Metallkationen und den negativ geladenen Phosphonsäuregruppen hochstabile Feststoffe. Eines der wichtigsten Ergebnisse dieser Arbeit besteht darin, daß 1,3,5-Tris(p-phosphonatophenyl)benzol als Linker zum Aufbau poröser Hybridmaterialien eingesetzt werden kann. Zum ersten Mal wurde ein dreifach phosphoniertes organisches Molekül zum Aufbau mikroporöser offener Phosphonat-Netzwerke verwendet. Zudem konnte gezeigt werden, daß die Porosität mit dem Wachstumsmechanismus dieser Materialien zusammenhängt. Es ist nur dann möglich ein gleichfalls mikroporöses und kristallines ionisches Netzwerk auf der Grundlage phosphonierter Moleküle zu erhalten, wenn Linker und Konnektor die gleiche Geometrie und Funktionalität besitzen.rn

Proton conductivity of mesoporous sol-gel zirconium phosphates for fuel cell applications

Zirconium phosphate has been extensively studied as a proton conductor for proton exchange membrane (PEM) fuel cell applications. Here we report the synthesis of mesoporous, templated sol-gel zirconium phosphate for use in PEM applications in an effort to determine its suitability for use as a surface functionalised, solid acid proton conductor in the future. Mesoporous zirconium phosphates were synthesised using an acid-base pair mechanism with surface areas between 78 and 177 m(2) g(-1) and controlled pore sizes in the range of 2-4 nm. TEM characterisation confirmed the presence of a wormhole like pore structure. The conductivity of such materials was up to 4.1 x 10(-6) S cm(-1) at 22degreesC and 84% relative humidity (RH), while humidity reduction resulted in a conductivity decrease by more than an order of magnitude. High temperature testing on the samples confirmed their dependence on hydration for proton conduction and low hydroscopic nature. It was concluded that while the conductivity of these materials is low compared to Nafion, they may be a good candidate as a surface functionalised solid acid proton conductor due to their high surface area, porous structure and inherent ability to conduct protons.

A NEW HYDROGEN SENSOR WITH RARE-EARTH COMPLEX FLUORIDE

A new type of solid-state galvanic cell for detecting a small amount of hydrogen in air at room temperature is proposed. The sensor cell is a potentiometric cell using Ce0.95Ca0.05F2.95 as solid-state electrolyte. The cell exhibits good sensing properties to hydrogen in air at room temperature.

Magnetic resonance study of a vanadium pentoxide gel

In this work we report results from continuous-wave (CW) and pulsed electron paramagnetic resonance (EPR) and proton nuclear magnetic resonance (NMR) studies of the vanadium pentoxide xerogel V2O5:nH(2)O (n approximate to 1.6). The low temperature CW-EPR spectrum shows hyperfine structure due to coupling of unpaired V4+ electron with the vanadium nucleus. The analysis of the spin Hamiltonian parameters suggests that the V4+ ions are located in tetragonally distorted octahedral sites. The transition temperature from the rigid-lattice low-temperature regime to the high temperature liquid-like regime was determined from the analysis of the temperature dependence of the hyperfine splitting and the V4+ motional correlation time. The Electron Spin Echo Envelope Modulation (ESEEM) data shows the signals resulting from the interaction of H-1 nuclei with V4+ ions. The modulation effect was observed only for field values in the center of the EPR absorption spectrum corresponding to the single crystals orientated perpendicular to the magnetic field direction. At least three protons are identified in the xerogel by our magnetic resonance experiments: (I) the OH groups in the equatorial plane, (ii) the bound water molecules in the axial V=O bond and (iii) the free mobile water molecules between the oxide layers. Proton NMR lineshapes and spin-lattice relaxation times were measured in the temperature range between 150 K and 323 K. Our analysis indicates that only a fraction of the xerogel protons contribute to the measured conductivity.