Microstructural features of flow instability in α-titanium cylinders under high strain rate compression at 25°C to 400°C

Cylindrical specimens of commercial pure titanium have been compressed at strain rates in the range of 0.1 to 100 s-1 and temperatures in the range of 25-degrees-C to 400-degrees-C. At strain rates of 10 and 100 s-1, the specimens exhibited adiabatic shear bands. At lower strain rates, the material deformed in an inhomogeneous fashion. These material-related instabilities are examined in the light of the ''phenomenological model'' and the ''dynamic materials mode.'' It is found that the regime of adiabatic shear band formation is predicted by the phenomenological model, while the dynamic materials model is able to predict the inhomogeneous deformation zone. The criterion based on power partitioning is competent to predict the variations within the inhomogeneous deformation zone.

Coordination modes of 3-aminosalicylic and 3-hydroxyanthranilic acids in palladium(II), platinum(II) and rhenium(V) complexes. The crystal structure of cis-[Pt(HsalNH)(PPh3)(2)] (.) 0.25C(2)H(5)OH

New Pd(II), Pt(II) and Re(V) complexes of 3-aminosalicylic acid (H(2)salNH(2)) and 3-hydroxyantranilic acid (HantOH) have been prepared, cis-[Pt (HsalNH)(PPh3)(2)] center dot 0.25C(2)H(5)OH (1), trans-[PdCl(salNH(2))(PPh3)(2)](2), trans-[ReOI2(HsalNH(2))(PPh3)] center dot (CH3)(2)CO (3), cis-[Pt(HantO)(PPh3)(2)] (4), trans-[PdCl(antOH)(PPh3)(2)] center dot 4H(2)O (5), [PdCl(antOH)(bipy)] center dot C2H5OH (6), [PdCl2(HantOH)(2)] (7) and trans-[ReOI(HantO)(PPh3)(2)] center dot (CH3)(2)CO (8). The crystal structure of complex I was determined showing chelation of HsalNH(2-) through the adjacent nitrogen and oxygen atoms of the amino and phenolate groups. Infrared and H-1 NMR spectroscopic data for the complexes are presented. (c) 2005 Elsevier Ltd. All rights reserved.

A hydrogen gas sensor based on Pt/nanostructured WO3/SiC Schottky diode

Pt/nanostructured WO3/SiC Schottky diodes were fabricated and applied for hydrogen gas sensing applications. The nanostructured WO3 films were synthesized from tungsten coated SiC substrates via an acid-etching method using a 1.5 M HNO3 solution for 1 hr, 2 hrs and 3 hrs duration. Scanning electron microscopy of the developed films revealed platelet crystals with thicknesses in the order of 20-60 nm and lengths between 100-700 nm. X-ray diffraction analysis revealed that the rate of oxidation of tungsten increases as the duration of acid-etching increases. The devices were tested towards hydrogen gas balanced in air at different temperatures from 25°C to 200°C. At 200°C, voltage shifts of 0.45 V, 0.93 V and 2.37 V were recorded for devices acid-etched for 1 hr, 2 hrs and 3 hrs duration, respectively upon exposure to 1% hydrogen, under a constant forward bias current of 500 µA.

Hydrogen gas sensing performance of a Pt/graphene/SiC device

In this work, we present the development of a Pt/graphene/SiC device for hydrogen gas sensing. A single layer of graphene was deposited on 6H-SiC via chemical vapor deposition. The presence of graphene C-C bonds was observed via X-ray photoelectron spectroscopy analysis. Current-voltage characteristics of the device were measured at the presence of hydrogen at different temperatures, from 25°C to 170°C. The dynamic response of the device was recorded towards hydrogen gas at an optimum temperature of 130°C. A voltage shift of 191 mV was recorded towards 1% hydrogen at −1 mA constant current.

Persistent digital hyperthermia over a 48 h period does not induce laminitis in horses

Persistent digital hyperthermia, presumably due to vasodilation, occurs during the developmental and acute stages of insulin-induced laminitis. The objectives of this study were to determine if persistent digital hyperthermia is the principal pathogenic mechanism responsible for the development of laminitis. The potent vasodilator, ATP-MgCl 2 was infused continuously into the distal phalanx of the left forefoot of six Standardbred racehorses for 48h via intra-osseous infusion to promote persistent digital hyperthermia. The right forefoot was infused with saline solution and acted as an internal control. Clinical signs of lameness at the walk were not detected at 0h, 24h or 48h post-infusion. Mean±SE hoof wall temperatures of the left forefoot (29.4±0.25°C) were higher (P<0.05) than those on the right (27.5±0.38°C). Serum insulin (15.0±2.89μIU/mL) and blood glucose (5.4±0.22mM) concentrations remained unchanged during the experiment. Histopathological evidence of laminitis was not detected in any horse. The results demonstrated that digital vasodilation up to 30 °C for a period of 48. h does not trigger laminitis in the absence of hyperinsulinaemia. Thus, although digital hyperthermia may play a role in the pathogenesis of laminitis, it is not the sole mechanism involved.

Methodological challenges when estimating the effects of season and seasonal exposures on birth outcomes

Background Many previous studies have found seasonal patterns in birth outcomes, but with little agreement about which season poses the highest risk. Some of the heterogeneity between studies may be explained by a previously unknown bias. The bias occurs in retrospective cohorts which include all births occurring within a fixed start and end date, which means shorter pregnancies are missed at the start of the study, and longer pregnancies are missed at the end. Our objective was to show the potential size of this bias and how to avoid it. Methods To demonstrate the bias we simulated a retrospective birth cohort with no seasonal pattern in gestation and used a range of cohort end dates. As a real example, we used a cohort of 114,063 singleton births in Brisbane between 1 July 2005 and 30 June 2009 and examined the bias when estimating changes in gestation length associated with season (using month of conception) and a seasonal exposure (temperature). We used survival analyses with temperature as a time-dependent variable. Results We found strong artificial seasonal patterns in gestation length by month of conception, which depended on the end date of the study. The bias was avoided when the day and month of the start date was just before the day and month of the end date (regardless of year), so that the longer gestations at the start of the study were balanced by the shorter gestations at the end. After removing the fixed cohort bias there was a noticeable change in the effect of temperature on gestation length. The adjusted hazard ratios were flatter at the extremes of temperature but steeper between 15 and 25°C. Conclusions Studies using retrospective birth cohorts should account for the fixed cohort bias by removing selected births to get unbiased estimates of seasonal health effects.

GWCarb v1.0: carbonate speciation tool

This spreadsheet calculates carbonate speciation using carbonate equilibrium equations at standard conditions (T=25°C) with ionic strength corrections. The user will typically be able to calculate the different carbonate species by entering total alkalinity and pH. This spreadsheet contains additional tools to calculate the Langelier Index for calcium and the SAR of the water. Note that in this last calculation the potential for calcium precipitation is not taken into account. The last tool presented here is a carbonate speciation tool in open systems (e.g. open to the atmosphere) which takes into account atmospheric pressure.

Layer silicates in a chondritic porous interplanetary dust particle

Analytical electron microscopy on individual grains from a portion of a chondritic porous interplanetary dust particle (aggregate W7029C1 from the NASA Johnson Space Center Cosmic Dust Collection) shows that layer silicates compose 50 percent of the silicate fraction examined. These layer silicates can be classified into two distinct crystallochemical groups: (1) fine-grained, polycrystalline smectite minerals; and (2) well-ordered, single crystals of kaolinite and Mg-poor talc. The layer silicates in this portion of sample W7029(asterisk)A are dissimilar to those described in other chondritic porous aggregates. The predominant layer silicate assemblage in W7029(asterisk)A indicates that heating of the aggregate during atmospheric entry was brief and probably to a temperature less than 300C. Comparison with terrestrial phyllosilicate occurrences suggests that some layer silicates in aggregate W7029(asterisk)A may have been formed by alteratiton from preexisting silicate minerals at low temperatures (less than 25C) after aggregate formation.

Utilization and optimization of a waste stream cellulose culture medium for pigment production by Penicillium spp

Aims This research sought to determine optimal corn waste stream–based fermentation medium C and N sources and incubation time to maximize pigment production by an indigenous Indonesian Penicillium spp., as well as to assess pigment pH stability. Methods and Results A Penicillium spp. was isolated from Indonesian soil, identified as Penicillium resticulosum, and used to test the effects of carbon and nitrogen type and concentrations, medium pH, incubation period and furfural on biomass and pigment yield (PY) in a waste corncob hydrolysate basal medium. Maximum red PY (497·03 ± 55·13 mg l−1) was obtained with a 21 : 1 C : N ratio, pH 5·5–6·0; yeast extract-, NH4NO3-, NaNO3-, MgSO4·7H2O-, xylose- or carboxymethylcellulose (CMC)-supplemented medium and 12 days (25°C, 60–70% relative humidity, dark) incubation. C source, C, N and furfural concentration, medium pH and incubation period all influenced biomass and PY. Pigment was pH 2–9 stable. Conclusions Penicillium resticulosum demonstrated microbial pH-stable-pigment production potential using a xylose or CMC and N source, supplemented waste stream cellulose culture medium. Significance and Impact of the Study Corn derived, waste stream cellulose can be used as a culture medium for fungal pigment production. Such application provides a process for agricultural waste stream resource reuse for production of compounds in increasing demand.

Pt/TiO2 nanotubes/SiC schottky diodes for hydrogen gas sensing applications

Titanium oxide nanotubes Schottky diodes were fabricated for hydrogen gas sensing applications. The TiO2 nanotubes were synthesized via anodization of RF sputtered titanium films on SiC substrates. Two anodization potentials of 5 V and 20 V were used. Scanning electron microscopy of the synthesized films revealed nanotubes with avarage diameters of 20 nm and 75 nm. X-ray diffraction analysis revealed that the composition of the oxide varied with the anodization potential. TiO2 (anatase) being formed preferentially at 5 V and TiO (no anatase) at 20 V. Current-voltage characteristics of the diodes were studied towards hydrogen at temperatures from 25°C to 250°C. At constant current bias of −500 μA and 250°C, the lateral voltage shifts of 800 mV and 520 mV were recorded towards 1% hydrogen for the 5 V and 20 V anodized nanotubes, respectively.

Pt/MoO3 nano-flower/SiC Schottky diode based hydrogen gas sensor

In this paper, we report the development of a novel Pt/MoO3 nano-flower/SiC Schottky diode based device for hydrogen gas sensing applications. The MoO3 nanostructured thin films were deposited on SiC substrates via thermal evaporation. Morphological characterization of the nanostructured MoO3 by scanning electron microscopy revealed randomly orientated thin nanoplatelets in a densely packed formation of nano-flowers with dimensions ranging from 250 nm to 1 μm. Current-voltage characteristics of the sensor were measured at temperatures from 25°C to 250°C. The sensor showed greater sensitivity in a reverse bias condition than in forward bias. Dynamic response of the sensor was investigated towards different concentrations of hydrogen gas in a synthetic air mixture at 250°C and a large voltage shift of 5.7 V was recorded upon exposure to 1% hydrogen.

Graphene-like nano-sheets based LiTaO3 surface acoustic wave NO2 gas sensor

Thin films consisting of graphene-like nano-sheets were deposited onto LiTaO3 surface acoustic wave transducers. A thickness of less than 10 nm and the existence of C-C bond were observed during the characterization of graphene-like nano-sheets. Frequency shift of 18.7 kHz and 14.9 kHz towards 8.5 ppm NO2 at two different operating temperature, 40°C and 25°C, respectively, was observed.

Greenhouse gas emissions from sub-tropical agricultural soils after addition of organic by-products

As the cost of mineral fertilisers increases globally, organic soil amendments (OAs) from agricultural sources are increasingly being used as substitutes for nitrogen. However, the impact of OAs on the production of greenhouse gases (CO2 and N2O) is not well understood. A 60-day laboratory incubation experiment was conducted to investigate the impacts of applying OAs (equivalent to 296 kg N ha−1 on average) on N2O and CO2 emissions and soil properties of clay and sandy loam soils from sugar cane production. The experiment included 6 treatments, one being an un-amended (UN) control with addition of five OAs being raw mill mud (MM), composted mill mud (CM), high N compost (HC), rice husk biochar (RB), and raw mill mud plus rice husk biochar (MB). These OAs were incubated at 60, 75 and 90% water-filled pore space (WFPS) at 25°C with urea (equivalent to 200 kg N ha−1) added to the soils thirty days after the incubation commenced. Results showed WFPS did not influence CO2 emissions over the 60 days but the magnitude of emissions as a proportion of C applied was RB < CM < MB < HC

Effect of fumigation temperature on the efficacy of phosphine against strongly resistant psocids liposcelis bostrychophila (Pscodoptera: Liposcelididae)

Species of Liposcelis psocids have emerged as major pests of stored grain in Australia in recent years. Several populations have been detected with high resistance to phosphine, the major chemical treatment. Highest resistance has been detected in the cosmopolitan species Liposcelis bostrychophila. As part of a national resistance management strategy to maintain the viability of phosphine, we are developing minimum effective dosage regimes (concentration x time) required to control all life stages of resistant L. bostrychophila at a range of grain temperatures. Four concentrations of phosphine, 0.1, 0.17, 0.3 aid 1 mg/L, were evaluated for their effectiveness against strongly resistant L. bostrychophila at a series of fumigation temperatures: 20, 25, 30 and 35°C. Results were recorded as the least number of days taken to achieve population extinction. We found that, at any fixed concentration of phosphine, time to population extinction decreased as fumigation temperature increased from 20 to 30°C. For example, at 0.1 mg/L, it took more than 14 days at 20°C to completely control these insects, whereas at 30°C it took only seven days. Increase in fumigation temperature from 25OC to 30°C dramatically reduced the exposure period needed to achieve population extinction of resistant psocids. For example, a dose of 0.17 mg/L over six days at 30°C completely controlled strongly resistant L. bostrychophila populations that can survive at 1 mg/L and 25°C over the same exposure period. Findings from our study will be used to formulate recommendations for registered dosage rates and fumigation periods for use in Australia.

Storage of Macadamia Nut-In-Shell

The effect of moisture content and storage temperature on the high quality storage life on macadamia nut-in-shell (NIS), and the subsequent influence of NIS storage on the shelf-life of roasted kernel, is being investigated. Macadamia integrifolia 'Keauhou" (HAES 246) NIS is being stored at 5°, 25°C and 40°C with a moisture content of 15.0, 12.5, 10.0, 7.5 and 3.5% for a maximum of 12 months. Preliminary results showed that unacceptable levels of visual mould developed on NIS with 15.0 and 12.5% moisture at 25°C following relatively short periods of storage. Discolouration and the production of an off-flavour in the raw kernel resulted after 1 month's storage of NIS with a moisture content of 10.0% at 40°C. Roasting times were reduced with increased storage duration of NIS with a moisture content of 15.0, 12.5 and 10.0% at 25°C, 15.0 and 12.5% at 5°C and 3.5% at 40°C. The percentage of roasted kernel rejects increased with increased storage duration of NIS with a moisture content of 15.0 and 12.5% at 25°C.