Implementing sustainable farming practices in the Herbert: The Oakleigh Farming Company experience

The Oakleigh Farming Company has been progressively changing its farming practices on its property at Cordelia in the Herbert River District. During the last ten years the changes have included the adoption of raised beds at 1.8m row spacing, controlled traffic and dual row planting using double disc opener planters. This paper describes some of the changes that have been made to the farming system and examines their impact on farm productivity and economic performance. Since changing to the current farming system, the farm gross margin has increased from $789/ha to $897/ha. In addition to the numerous cost savings, the new farming system has reduced the time spent on tractors by 54% across the whole farm. Return on investment on the 1997 farming system was 1.6% versus 2.7% on their current farming system. The farming company is continually looking for new ways to improve profitability and believes that innovation is critical for the long term sustainability of the sugar industry.

Long-term Ingham and Mackay farming system experiments: comparisons between permanent non-tilled beds and re-formed beds

Experiments involving row spacing and tillage, originally established in Mackay and Ingham in 2001, were planted to a second cycle of sugarcane in 2006 following a soybean break. Despite large yield differences, economic analysis indicated that there would be little difference in gross margins because of the much higher costs of the tilled system. It is concluded that without GPS guidance, as was the case with these experiments, cane yields are likely to be reduced with no tillage but these problems may well be overcome by implementing minimum strategic tillage to remove compaction from the planting row.

A case study on the economics of overhead irrigation in the lower Burdekin

Converting from an existing irrigation system is often seen as high risk by the land owner. The significant financial investment and the long period over which the investment runs is also complicated by the uncertainty associated with long term input costs (such as energy), crop production, and the continually evolving natural resource management rules and policy. Irrigation plays a pivotal part in the Burdekin sugarcane farming system. At present the use of furrow irrigation is by far the most common form due to the ease of use, relatively low operating cost and well established infrastructure currently in place. The Mulgrave Area Farmer Integrated Action (MAFIA) grower group, located near Clare in the lower Burdekin region, identified the need to learn about sustainable farming systems with a focus on the environment, social and economic implications. In early 2007, Hesp Faming established a site to investigate the use of overhead irrigation as an alternative to furrow irrigation and its integration with new farming system practices, including Green Cane Trash Blanketing (GCTB). Although significant environmental and social benefits exist, the preliminary investment analysis indicates that the Overhead Low Pressure (OHLP) irrigation system is not adding financial value to the Hesp Farming business. A combination of high capital costs and other offsetting factors resulted in the benefits not being fully realised. A different outcome is achieved if Hesp Farming is able to realise value on the water saved, with both OHLP irrigation systems displaying a positive NPV. This case study provides a framework to further investigate the economics of OHLP irrigation in sugarcane and it is anticipated that with additional data a more definitive outcome will be developed in the future.

Economic evaluation of precision controlled traffic farming in the Australian sugar industry: a case study of an early adopter

Controlled traffic has been identified as the most practical method of reducing compaction-related soil structural degradation in the Australian sugarcane industry. GPS auto-steer systems are required to maximize this potential. Unfortunately there is a perception that little economic gain will result from investing in this technology. Regardless, a number of growers have made the investment and are reaping substantial economic and lifestyle rewards. In this paper we assess the cost effectiveness of installing GPS guidance and using it to implement Precision Controlled Traffic Farming (PCTF) based on the experience of an early adopter. The Farm Economic Analysis Tool (FEAT) model was used with data provided by the grower to demonstrate the benefits of implementing PCTF. The results clearly show that a farming system based on PCTF and the minimum tillage improved farm gross margin by 11.8% and reduced fuel usage by 58%, compared to producers' traditional practice. PCTF and minimum tillage provide sugar producers with a tool to manage the price cost squeeze at a time of low sugar prices. These data provide producers with the evidence that investment in PCTF is economically prudent.

Lexicon for the Sensory Description of Australian Native Plant Foods and Ingredients

Understanding and describing Australian flavor has proved to be a challenge for marketers of native foods because of the diversity of unique flavor signatures exhibited. Descriptive analysis techniques were applied, using a panel of 11 experienced judges, to define and articulate the sensory properties of 18 key commercial Australian native plant foods and ingredients including fruits, herbs and spices. Quantitative descriptive data were transformed into concise and accurate verbal descriptions for each of the species. The sensory language developed during the vocabulary development panel sessions was combined, categorized and ordered to develop a sensory lexicon specific for the genre. The language developed to describe the foods and ingredients was diverse and distinctly Australian including aromas such as musk, rosella, citrus and spiced tea to eucalypt, bush scrub, fresh beetroot and wheat biscuit. Practical Applications This work provides a clear, useful means of characterizing and accurately describing the flavors of Australian native plant foods and ingredients. This information has been communicated to the native food industry, chefs, formulators, food technologists and flavor experts, and provides knowledge that will assist the wider food industry to successfully develop flavor blends and produce food products from native food ingredients. It is anticipated that extension of this information to both the local and international food markets will stimulate a renewed interest in Australian native ingredients and open new market opportunities for the industry. The data developed by this research have also formed the basis of quality control targets for emerging native foods and ingredients.

Sugarcane productivity response to different fallow and soybean residue management practices in the Bundaberg district

GRAIN LEGUME ROTATIONS underpin the sustainability of the Australian sugarcane farming system, offering a number of soil health and environmental benefits. Recent studies have highlighted the potential for these breaks to exacerbate nitrous oxide (N2O) emissions. An experiment was implemented in 2012 to evaluate the impact of two fallow management options (bare fallow and soybean break crop) and different soybean residue management practices on N2O emissions and sugarcane productivity. The bare fallow plots were conventionally tilled, whereas the soybean treatments were either tilled, not tilled, residue sprayed with nitrification inhibitor (DMPP) prior to tillage or had a triticale ‘catch crop’ sown between the soybean and sugarcane crops. The fallow plots received either no nitrogen (N0) or fully fertilised (N145) whereas the soybean treatments received 25 kg N/ha at planting only. The Fallow N145 treatment yielded 8% more cane than the soybean tilled treatment. However there was no statistical difference in sugar productivity. Cane yield was correlated with stalk number that was correlated to soil mineral nitrogen status in January. There was only 30% more N/ha in the above-ground biomass between the Fallow N145 and the Fallow N0 treatment; highlighting poor fertiliser nitrogen use efficiency. Supplying adequate nitrogen to meet productivity requirements without causing environmental harm remains a challenge for the Australian sugar industry. The soybean direct drill treatment significantly reduced N2O emissions and produced similar yields and profitability to the soybean tilled treatment (outlined in a companion paper by Wang et.al. in these proceedings). Furthermore, this study has highlighted that the soybean direct drill technique provides an opportunity to enable grain legume cropping in the sugarcane farming system to capture all of the soil health/environmental benefits without exacerbating N2O emissions from Australian sugarcane soils.

Soybean rotation and crop residue management to reduce nitrous oxide emissions from sugarcane soils

NITROUS OXIDE (N2O) IS a potent greenhouse gas and the predominant ozone-depleting substance in the atmosphere. Agricultural nitrogenous fertiliser use is the major source of human-induced N2O emissions. A field experiment was conducted at Bundaberg from October 2012 to September 2014 to examine the impacts of legume crop (soybean) rotation as an alternative nitrogen (N) source on N2O emissions during the fallow period and to investigate low-emission soybean residue management practices. An automatic monitoring system and manual gas sampling chambers were used to measure greenhouse gas emissions from soil. Soybean cropping during the fallow period reduced N2O emissions compared to the bare fallow. Based on the N content in the soybean crop residues, the fertiliser N application rate was reduced by about 120 kg N/ha for the subsequent sugarcane crop. Consequently, emissions of N2O during the sugarcane cropping season were significantly lower from the soybean cropped soil than those from the conventionally fertilised (145 kg N/ha) soil following bare fallow. However, tillage that incorporated the soybean crop residues into soil promoted N2O emissions in the first two months. Spraying a nitrification inhibitor (DMPP) onto the soybean crop residues before tillage effectively prevented the N2O emission spikes. Compared to conventional tillage, practising no-till with or without growing a nitrogen catch crop during the time after soybean harvest and before cane planting also reduced N2O emissions substantially. These results demonstrated that soybean rotation during the fallow period followed with N conservation management practices could offer a promising N2O mitigation strategy in sugarcane farming. Further investigation is required to provide guidance on N and water management following soybean fallow to maintain sugar productivity.

Evaluation of mud filtrate clarification to improve factory performance

Clarification performance and flocculant dosage is strongly linked to the mud solids loading in the feed entering the clarifier. The recycle of filtrate can represent an extra ~10-15% mud solids loading on the clarifier, thereby reducing its effective capacity. Filtrate recycling may cause significant increase in turbidity, complexed calcium ion formation, phosphate, proteins and polysaccharides in mixed juice that impact on evaporator scale formation and molasses exhaustion. The paper details the results obtained from laboratory, pilot scale and factory trials of filtrate clarification using both sedimentation and flotation methods. Clarified filtrate could be produced of similar quality to ESJ. Filtrate clarification was able to significantly remove insoluble solids, turbidity, phosphate, and polysaccharides content with slight reductions in minerals content of the filtrate. On the basis of improved filtrate quality, the clarified filtrate could be directed to ESJ, instead of the normal practice of directing the mud filtrate to mixed juice. The potential impacts of implementing filtrate clarification are discussed in respect to improved performance and throughput of the clarification station.

Microbial oil production from sugarcane bagasse hydrolysates by oleaginous yeast and filamentous fungi

This study investigated the potential use of sugarcane bagasse as a feedstock for oil production through microbial cultivation. Bagasse was subjected to dilute acid pretreatment with 0.4 wt% H2SO4 (in liquid) at a solid/liquid ratio of 1:6 (wt/wt) at 170 °C for 15 min, followed by enzymatic hydrolysis of solid residue. The liquid fractions of the pretreatment process and the enzymatic hydrolysis process were detoxified and used as liquid hydrolysate (SCBLH) and enzymatic hydrolysate (SCBEH) for the microbial oil production by oleaginous yeast (Rhodotorula mucilaginosa) and filamentous fungi (Aspergillus oryzae and Mucor plumbeus). The results showed that all strains were able to grow and produce oil from bagasse hydrolysates. The highest oil concentrations produced from bagasse hydrolysates were by M. plumbeus at 1.59 g/L (SCBLH) and 4.74 g/L (SCBEH). The microbial oils obtained have similar fatty acid compositions to vegetable oils, indicating that the oil can be used for the production of second generation biodiesel. On the basis of oil yields obtained by M. plumbeus, from 10 million t (wet weight) of bagasse generated annually from sugar mills in Australia, it is estimated that the total biodiesel that could be produced would be equivalent to about 9% of Queensland’s diesel consumption.

Scheduling tools to reduce the cost of cane railway transport

Cane railway systems provide empty bins for harvesters to fill and full bins of cane for the factory to process. These operations need to be conducted in a timely fashion to minimise delays to harvesters and the factory and to minimise the cut-to-crush delay, while also minimising the cost of providing this service. A range of tools has been provided over the years to assist in this process. This paper reviews the objectives of the cane transport system and the tools available to achieve those objectives. The facilities within these tools to assist in the control of costs are highlighted.

Carotenoids In 3 Stages Of Ripening Of Mango

The distribution of carotenoids, both qualitative and quantitative, during 3 stages of ripening of mango has been studied using chromatographic, spectroscopic and chemical methods. There was an increase in content as well as in number of carotenoids during ripening. The present study showed there were 15, 14 and 17 different carotenoids in the unripe, partially ripe and fully ripe mangoes, respectively. Even though phytofluene (39.26%) was the major carotenoid in the partially ripe mango, β-carotene constituted the major carotenoid in the unripe (37.47%) and fully ripe mango (50.64%). cis-β-Carotene was present only in the fully ripe mango. Only the unripe mango contained ζ-carotene, whereas γ-carotene was present in all the 3 stages of ripening. The major xanthophyll present in the unripe mango was mutatoxanthin (9.44%), whereas auroxanthin constituted the major hydroxylated carotenoid of the partially ripe (5.07%) and fully ripe (10.40%) mangoes. The percent of cryptoxanthin dropped to lower levels during ripening. As ripening proceeded, lutein completely is appeared. There were significant quantities of eaxanthin in the partially ripe and fully ripe mango. Epoxy carotenoids such as 5,6-monoepoxy-β-carotene, mutatochrome, cis-violaxanthin, luteoxanthin, mutatoxanthin and auroxanthin were observed in all 3 stages of ripening.

Rauhan atomi, sodan koodi : Suomalaisen atomivoimaratkaisun teknopolitiikka 1955-1970

This dissertation investigates the atomic power solution in Finland between 1955 - 1970. During these years a national arrangement for atomic energy technology evolved. The foundations of the Finnish atomic energy policy; the creation of basic legislation and the first governmental bodies, were laid between 1955 - 1965. In the late 1960's, the necessary technological and political decisions were made in order to purchase the first commercial nuclear reactor. A historical narration of this process is seen in the international context of "atoms for peace" policies and Cold War history in general. The geopolitical position of Finland made it necessary to become involved in the balanced participation in international scientific-technical exchange and assistive nuclear programs. The Paris Peace Treaty of 1947 categorically denied Finland acquisition of nuclear weapons. Accordingly, from the "Geneva year" of 1955, the emphasis was placed on peaceful purposes for atomic energy as well as on the education of national professionals in Finland. An initiative for the governmental atomic energy commission came from academia but the ultimate motive behind it was an anticipated structural change in the supply of national energy. Economically exploitable hydro power resources were expected to be built within ten years and atomic power was seen as a promising and complementing new energy technology. While importing fuels like coal was out of the question, because of scarce foreign currency, domestic uranium mineral deposits were considered as a potential source of nuclear fuel. Nevertheless, even then nuclear energy was regarded as just one of the possible future energy options. In the mid-1960 s a bandwagon effect of light water reactor orders was witnessed in the United States and soon elsewhere in the world. In Finland, two separate invitations for bids for nuclear reactors were initiated. This study explores at length both their preceding grounds and later phases. An explanation is given that the parallel, independent and nearly identical tenders reflected a post-war ideological rivalry between the state-owned utility Imatran Voima and private energy utilities. A private sector nuclear power association Voimayhdistys Ydin represented energy intensive paper and pulp industries and wanted to have free choice instead of being associated themselves with "the state monopoly" in energy pricing. As a background to this, a decisive change had started to happen within Finnish energy policy: private and municipal big thermal power plants became incorporated into the national hydro power production system. A characteristic phenomenon in the later history is the Soviet Union s effort to bid for the tender of Imatran Voima. A nuclear superpower was willing to take part in competition but not on a turnkey basis as Imatran Voima had presumed. As a result of many political turns and four years of negotiations the first Finnish commercial light water reactor was ordered from the East. Soon after this the private nuclear power group ordered its reactors from Sweden. This work interprets this as a reasonable geopolitical balance in choosing politically sensitive technology. Conceptually, social and political dimensions of new technology are emphasised. Negotiations on the Finnish atomic energy program are viewed as a cooperation and a struggle, where state-oriented and private-oriented regimes pose their own macro level views and goals (technopolitical imaginaries) and defend and advance their plans and practical modes of action (schemata). Here, not only technologists but even political actors are seen to contribute to technopolitical realisations.

BIMODAL NANOINDENTATION RESPONSE OF THE (001) FACE IN CRYSTALLINE SODIUM SACCHARIN DIHYDRATE

The nanoindentation response of the (001) face of sodium saccharin dihydrate is examined. The structure can be demarcated into regular and irregular regions or domains. The regular domains have solid-like and the irregular ones have liquid-like characteristics. Therefore, these domains impart a microstructure to the crystal. The indent face (001) is prominently developed in this crystal and unambiguously presents the regular and irregular regions to nanoindention. Average values of elastic modulus and hardness show a distinct bimodal mechanical response. Such a response has been observed in the case of intergrown polymorphs of aspirin and felodipine. We examine two possible reasons as to why the responses could be for bimodal in this crystal. The first possibility could be that the two domains correspond to regions of the original dihydrate and a lower hydrate that is obtained by the loss of some water. The second possibility could be that these responses correspond to regular and irregular regions in the structure. Nanoindentation is a very useful technique in the characterization of molecular solids, as a complementary technique to X-ray crystallography, because it samples different length scales.

Meeting der WEFTA in Galway, Ireland

Die WEFTA (West European Fish Technologists Association – gegründet 1970) ist ein Zusammenschluß von Europäischen Instituten, die auf dem Gebiet Fischerei, Fischqualität und –verarbeitung arbeiten und forschen. Ziele der WEFTA sind der Informationsaustausch zwischen Wissenschaftlern und Fischindustrie auf Jahrestreffen und Arbeitsgruppen sowie die Ausweitungund Verbesserung der Zusammenarbeit unterschiedlicher Interessengruppen und Instituten in Projekten. Weitere Informationen können der Homepage der WEFTA (www.wefta.nl) zu entnommen werden.