云雾山本氏针茅群落根系分布特征

为揭示本氏针茅(Stipa bungeana Trin.)群落的生理生态适应机制,采用根系取样器(Φ=9 cm)对宁夏云雾山本氏针茅群落根系分布特征和土壤含水量进行研究。结果表明:本氏针茅群落地下生物量、根长密度、根表面积、比根长均随土壤深度增加而减少,均表现出向表层(0~20 cm)集聚的趋势,且集中分布于0~40 cm土层,最大值均分布在0~20 cm土层,而底层(80~100 cm)最小;所有主要根系分布参数在0~20 cm和20~40 cm土层之间差异显著,以下各层差异不显著;土壤含水量与根生物量和比根长相关性达显著水平(P<0.05),与根表面积、根长密度均呈成正相关;根表面积、根生物量、根长密度和比根长间相关性均达极显著水平(P<0.01)。

不同水分状况下秸秆覆盖量对玉米根、冠生长的影响

在遮雨棚控水条件下,采用盆栽的方式研究了不同秸秆覆盖量对玉米根、冠生长的影响。试验按对照(CK)和秸秆覆盖量0.3 kg/m2(SM0.3)、0.6 kg/m2(SM0.6)、0.9 kg/m2(SM0.9)、1.2 kg/m2(SM1.2)共设5个处理,水分按高水(占田间持水量的90%)和低水(占田间持水量的60%)设两个水平。分别测定了玉米根、茎、叶、穗干重,根系垂直空间分布及叶片叶绿素相对含量等指标。结果表明:秸秆覆盖明显改变了玉米根系和地上部分的生长;高水条件下SM0.6处理玉米根系、茎秆、叶和穗干重均高于其它处理;低水条件下,地上部分干重SM1.2最大,SM0.6次之;根系的垂直空间分布与水分和覆盖条件都有密切的关系,覆盖措施主要影响下层根系的生长和发育。

沙棘的水土保持功能及其在治理和开发黄土高原中的作用(英文)

研究表明 ,5～ 7年生沙棘林冠层可截留降水 8 5%～ 4 9 0 % ,并降低雨滴动能 ;枯枝落叶层重5 4 6t·hm- 2 ,其最大持水量可达 15 31t·hm- 2 ,有 1cm厚枯枝落叶层覆盖地表 ,即可基本控制水土流失 ;根系可以提高土壤的抗冲性和抗蚀性 ,与无根系土壤相比 ,可减少土壤冲刷量 55%～ 88% .据1988～ 1994年雨季径流小区测定 ,沙棘林在栽植后 4～ 5年可充分发挥水土保持作用 ,与农地相比 ,可减少地表径流量 87 1% ,减少土壤流失量 99 0 % .此外 ,它还可以每 4～ 5年提供薪材 10～ 30t·hm- 2 ,提高土壤中有机质和氮素含量 115%和 90 % ,生产沙棘果实 50 0kg·hm- 2 .所有这些表明了沙棘在治理黄土高原水土流失和改善人民生活条件 ,在实现由“恶性循环”向“良性循环”转变等方面 ,具有十分重要的作用 .目前 ,黄土地区已建立起若干利用沙棘固坡、防洪、解决燃料短缺和综合治理小流域的成功典型

根系吸水机理研究进展

植物根系除支撑和固定其地上部这一力学功能外的一个重要功能就是从土壤中吸收水分和养分以满足植物地上部生长所需.表征植物根吸水能力的一个重要的水力学参数是水力导度(用单位时间单位面积的水流速率来表示),可在细胞(细胞水力导度)、单根和整株根系水平上来表达,其中单根导度可分为径向导度和轴向导度,仅径向导度反映了单根吸收水分的能力,而轴向导度则反映了植物根系输导水分的能力,但在整株根系水平上则以通过整个根系的水流通量与根木质部和根表土壤间的水势差之比来表示,既包括径向导度也包括轴向导度.近年来,对植物根系吸水或根水力导度研究已取得了许多重要进展,这对阐明根系吸水机理和地上地下部关系起到了重要作用.下面做一简要综述.1　根系吸收水分的主要部位根系吸水的部位一般认为在距根尖10～100ｍｍ的区域内,这种看法是基于解剖上的证据.从根表面到根中心,依次为根表皮、下表皮、皮层、内皮层、中柱,其中根表皮是有最高吸收活性的根区,但一般仅可存活几天,而内皮层将皮层和中柱分开形成了根内侧的一个界面,老根一般有周皮或栓质化的内皮层,有很强的不透水性(即阻力很大).但Ｓａｎｄｅｒｓｏｎ[1]对大麦的研究发现,虽然老根区内重度栓化的内皮层已...

压力室测定根系导水率方法探讨

用压力室连续测定了玉米根系升压和降压过程的导水率。结果表明 ,降压过程测得的根系导水率显著大于用升压过程的 ,并且前者的相关系数大于后者。这种差异是由于这两个过程中质外体途径细胞壁空间充水量不同造成的。开始升压时 ,由于细胞壁空间含水量低 ,质外体途径阻力大 ,导致非结构阻力 ;随着压力的升高 ,细胞壁空间含水量增大 ,质外体途径导度增大 ,减小甚至可以消除非结构阻力。降压法可以使根系快速复水 ,消除传统方法因长时间复水所致根结构的改变。建议用降压法测定根系导水率

容器苗质量评定指标的研究

In this paper,the assessing indices of container seedlings quality were synthesized in accordance with growth and physiological factors. The results showed that the seedling quality might be determined by the dormancy state of terminal bud,nutrient condition of plant,and the state of root system. The critical quality indices should include stem diameter at soil surface,dry weight of terminal bud,and soluble sugar content. Moreover,some indices such as root system vitality and dry weight of plant were also important.

一种基于排队论的DoS攻防绩效评估方法

提出了一种新的基于排队论的DoS攻防绩效评估方法.针对不同种类DoS攻防手段建立了统一的指标体系和绩效计算方法,基于排队论方法分别建立评估模型,对UDP Flood和SYN Flood攻击的绩效进行不包含主观因素的定量评估,分析不同攻击手段和强度的有效性.针对典型DoS攻防场景,利用网络仿真工具进行模拟,通过实验与模型推导结果对比验证了排队论模型的合理性,并阐述了此方法在不同类型DoS攻防手段中的应用.

Observation and modeling for terrestrial processes in alpine meadow

The water-heat transfer process between land and atmosphere in Haibei alpine meadow area has been systematically observed. A multi-layer coupling model for land-atmosphere interaction was presented with special attention paid to the moisture transfer in leaf stomata under unsaturated condition. A profound investigation on the physical process of turbulent transfer inside the vegetation has been performed with a revised formula of water absorption for root system. The present model facilitates the study of vertically distributed physical variables in detail. Numerical simulation was conducted according to the transfer process of Kinesia humility meadow in the area of Haibei Alpine Meadow Ecosystem Station, CAS. The calculated results agree well with observation.

基于网络的多机器人遥操作系统中的人机交互研究

针对基于网络的智能机器人遥操作系统中人机交互的主要难点和现有方法的不足,结合基于网络的多机器人遥操作系统的特点,应用多模式控制的方法丰富了操作者与机器人系统的交互途径,提高了操作效率.在此基础上,为解决网络时延给多机器人遥操作系统中的人机交互带来的问题,提出了一种带有时间标记的基于事件的方法,在保证系统稳定运行的同时提高了系统的效率和性能.实验证明了所提方法的有效性和优越性.

K1 of Chevalley groups are nilpotent

Abstract Let F be a reduced irreducible root system and R be a commutative ring. Further, let G(F,R) be a Chevalley group of type F over R and E(F,R) be its elementary subgroup. We prove that if the rank of F is at least 2 and the Bass-Serre dimension of R is finite, then the quotient G(F,R)/E(F,R) is nilpotent by abelian. In particular, when G(F,R) is simply connected the quotient K1(F,R)=G(F,R)/E(F,R) is nilpotent. This result was previously established by Bak for the series A1 and by Hazrat for C1 and D1. As in the above papers we use the localisation-completion method of Bak, with some technical simplifications.

Uptake, translocation and transformation of arsenate and arsenite in sunflower (Helianthus annuus):formation of arsenic-phytochelatin complexes during exposure to high arsenic concentrations

The aim of the study was to determine the time-dependent formation of arsenic-phytochelatin (As-PC) complexes in the roots, stems and leaves of an arsenic-nontolerant plant (Helianthus annuus) during exposure to 66 mol l(-1) arsenite (As(III)) or arsenate (As(V)). We used our previously developed method of simultaneous element-specific (inductively coupled plasma mass spectrometry, ICP-MS) and molecular-specific (electrospray-ionization mass spectrometry, ES-MS) detection systems interfaced with a suitable chromatographic column and eluent conditions, which enabled us to identify and quantify As-PC complexes directly. Roots of As-exposed H. annuus contained up to 14 different arsenic species, including the complex of arsenite with two (gamma-Glu-Cys)(2)-Gly molecules [As((III))-(PC(2))(2)], the newly identified monomethylarsonic phytochelatin-2 or (gamma-Glu-Cys)(2)-Gly CH(3)As (MA((III))-PC(2)) and at least eight not yet identified species. The complex of arsenite with (gamma-Glu-Cys)(3)-Gly (As((III))-PC(3)) and the complex of arsenite with glutathione (GSH) and (gamma-Glu-Cys)(2)-Gly (GS-As((III))-PC(2)) were present in all samples (roots, stems and leaves) taken from plants exposed to As. The GS-As((III))-PC(2) complex was the dominant complex after 1 h of exposure. As((III))-PC(3) became the predominant As-PC complex after 3 h, binding up to 40% of the As present in the exposed plants. No As-PC complexes were found in sap (mainly xylem sap from the root system), in contrast to roots, stems and leaves, which is unequivocal evidence that As-PC complexes are not involved in the translocation of As from root to leaves of H. annuus.

Field Measurements of a Full Scale Tidal Device

Field testing studies are required for tidal turbine device developers to determine the performance of their turbines in tidal flows. Full-scale testing of the SCHOTTEL tidal turbine has been conducted at Queen’s University Belfast’s tidal site at Strangford Lough, NI. The device was mounted on a floating barge. Testing was conducted over 48 days, for 288 h, during flood tides in daylight hours. Several instruments were deployed, resulting in an expansive data set. The performance results from this data set are presented here. The device, rated to 50 kW at 2.75 m/s was tested in flows up to 2.5 m/s, producing up to 19 kW, when time-averaged. The thrust on the turbine reached 17 kN in the maximum flow. The maximum system efficiency of the turbine in these flows reached 35%. The test campaign was very successful and further tests may be conducted at higher flow speeds in a similar tidal environment.

Three-port DC-DC Converter for Stand-Alone Photovoltaic Systems

System efficiency and cost effectiveness are of critical importance for photovoltaic (PV) systems. This paper addresses the two issues by developing a novel three-port DC-DC converter for stand-alone PV systems, based on an improved Flyback-Forward topology. It provides a compact single-unit solution with a combined feature of optimized maximum power point tracking (MPPT), high step-up ratio, galvanic isolation and multiple operating modes for domestic and aerospace applications. A theoretical analysis is conducted to analyze the operating modes followed by simulation and experimental work. The paper is focused on a comprehensive modulation strategy utilizing both PWM and phase-shifted control that satisfies the requirement of PV power systems to achieve MPPT and output voltage regulation. A 250 W converter was designed and prototyped to provide experimental verification in term of system integration and high conversion efficiency.

Investigations Into the Performance of a Turbogenerated Biogas Engine During Speed Transients

Turbogenerating is a form of turbocompounding whereby a Turbogenerator is placed in the exhaust stream of an internal combustion engine. The Turbogenerator converts a portion of the expelled energy in the exhaust gas into electricity which can then be used to supplement the crankshaft power. Previous investigations have shown how the addition of a Turbogenerator can increase the system efficiency by up to 9%. However, these investigations pertain to the engine system operating at one fixed engine speed. The purpose of this paper is to investigate how the system and in particular the Turbogenerator operate during engine speed transients. On turbocharged engines, turbocharger lag is an issue. With the addition of a Turbogenerator, these issues can be somewhat alleviated. This is done by altering the speed at which the Turbogenerator operates during the engine’s speed transient. During the transients, the Turbogenerator can be thought to act in a similar manner to a variable geometry turbine where its speed can cause a change in the turbocharger turbine’s pressure ratio. This paper shows that by adding a Turbogenerator to a turbocharged engine the transient performance can be enhanced. This enhancement is shown by comparing the turbogenerated engine to a similar turbocharged engine. When comparing the two engines, it can be seen that the addition of a Turbogenerator can reduce the time taken to reach full power by up to 7% whilst at the same time, improve overall efficiency by 7.1% during the engine speed transient.

Runtime Support for Adaptive Power Capping on Heterogeneous SoCs

Power capping is a fundamental method for reducing the energy consumption of a wide range of modern computing environments, ranging from mobile embedded systems to datacentres. Unfortunately, maximising performance and system efficiency under static power caps remains challenging, while maximising performance under dynamic power caps has been largely unexplored. We present an adaptive power capping method that reduces the power consumption and maximizes the performance of heterogeneous SoCs for mobile and server platforms. Our technique combines power capping with coordinated DVFS, data partitioning and core allocations on a heterogeneous SoC with ARM processors and FPGA resources. We design our framework as a run-time system based on OpenMP and OpenCL to utilise the heterogeneous resources. We evaluate it through five data-parallel benchmarks on the Xilinx SoC which allows fully voltage and frequency control. Our experiments show a significant performance boost of 30% under dynamic power caps with concurrent execution on ARM and FPGA, compared to a naive separate approach.