Non-resorbable glass fibre-reinforced composite with porous surface as bone substitute material: Experimental studies in vitro and in vivo focused on bone-implant interface

The development of load-bearing osseous implant with desired mechanical and surface properties in order to promote incorporation with bone and to eliminate risk of bone resorption and implant failure is a very challenging task. Bone formation and resoption processes depend on the mechanical environment. Certain stress/strain conditions are required to promote new bone growth and to prevent bone mass loss. Conventional metallic implants with high stiffness carry most of the load and the surrounding bone becomes virtually unloaded and inactive. Fibre-reinforced composites offer an interesting alternative to metallic implants, because their mechanical properties can be tailored to be equal to those of bone, by the careful selection of matrix polymer, type of fibres, fibre volume fraction, orientation and length. Successful load transfer at bone-implant interface requires proper fixation between the bone and implant. One promising method to promote fixation is to prepare implants with porous surface. Bone ingrowth into porous surface structure stabilises the system and improves clinical success of the implant. The experimental part of this work was focused on polymethyl methacrylate (PMMA) -based composites with dense load-bearing core and porous surface. Three-dimensionally randomly orientated chopped glass fibres were used to reinforce the composite. A method to fabricate those composites was developed by a solvent treatment technique and some characterisations concerning the functionality of the surface structure were made in vitro and in vivo. Scanning electron microscope observations revealed that the pore size and interconnective porous architecture of the surface layer of the fibre-reinforced composite (FRC) could be optimal for bone ingrowth. Microhardness measurements showed that the solvent treatment did not have an effect on the mechanical properties of the load-bearing core. A push-out test, using dental stone as a bone model material, revealed that short glass fibre-reinforced porous surface layer is strong enough to carry load. Unreacted monomers can cause the chemical necrosis of the tissue, but the levels of leachable resisidual monomers were considerably lower than those found in chemically cured fibre-reinforced dentures and in modified acrylic bone cements. Animal experiments proved that surface porous FRC implant can enhance fixation between bone and FRC. New bone ingrowth into the pores was detected and strong interlocking between bone and the implant was achieved.

Non conventional biological treatment based on Trametes versicolor for the elimination of recalcitrant anticancer drugs in hospital wastewater

This work presents a study about the elimination of anticancer drugs, a group of pollutants considered recalcitrant during conventional activated sludge wastewater treatment, using a biological treatment based on the fungus Trametes versicolor. A 10-L fluidized bed bioreactor inoculated with this fungus was set up in order to evaluate the removal of 10 selected anticancer drugs in real hospital wastewater. Almost all the tested anticancer drugs were completely removed from the wastewater at the end of the batch experiment (8 d) with the exception of Ifosfamide and Tamoxifen. These two recalcitrant compounds, together with Cyclophosphamide, were selected for further studies to test their degradability by T. versicolor under optimal growth conditions. Cyclophosphamide and Ifosfamide were inalterable during batch experiments both at high and low concentration, whereas Tamoxifen exhibited a decrease in its concentration along the treatment. Two positional isomers of a hydroxylated form of Tamoxifen were identified during this experiment using a high resolution mass spectrometry based on ultra-high performance chromatography coupled to an Orbitrap detector (LTQ-Velos Orbitrap). Finally the identified transformation products of Tamoxifen were monitored in the bioreactor run with real hospital wastewater

Sensory and Non-sensory Factors Behind the Liking and Choice of Healthy Food Products

A healthy and balanced diet can reduce health problems, such as overweight and metabolic syndrome. In general, people have a considerably good knowledge of what constitutes a healthy diet and how they could achieve it with their food choices. Besides, people argue that health is among their top five food choice motives. Nevertheless, the prevalence of overweight is increasing and other food choice motives, such as taste, seem to conflict with the health. Liking for food does not necessarily determine acceptance alone, thus several non-sensory factors, such as brand, country of origin and nutrition claim, can also influence. Moreover, consumers are individuals in how they prioritize sensory and nonsensory factors of foods, but e.g. increasing age, female gender and health concern have been connected to a more health-oriented dietary behaviour. To sum up, identifying different factors that can increase the liking and consumption of healthy food is essential in order to develop more attractive healthful food products. Adding vitamins, minerals, fibre or other ingredients to a food product can be used to enrich the nutritional quality of the products. However, this may be difficult in practice as regards the sensory quality and pleasantness of the foods. Generally, consumers are not willing to compromise on taste in food. On the other hand, consumers are very heterogeneous in their likings, and their personal values and attitudes may interact with preferences for specific sensory characteristics. The aims of this study were to investigate the effects of intrinsic product characteristics on sensory properties and hedonic responses; to determine the impact of few non-sensory factors; and to examine the interaction between sensory and non-sensory factors with consumers’ demographics, values and attitudes in liking of healthy model foods. The results showed that product composition influenced sensory quality and had an effect on hedonic responses. Adding flaxseed to bakery products showed a significant improvement in the nutritional quality without negative effects on sensory properties. On the other hand, the fortification of wellness beverages with vitamins and minerals may impart off-flavours. In general, sweetness of yoghurts, freshness of wellness beverages and low intensity of rye bread flavour appealed to consumers. Information about the domestic origin of yoghurts and claiming a specific function for wellness beverages enhanced liking. However, consumers who were more concerned about their health and considered natural content as an important food choice motive, rated sourer and less sweet yoghurts and wellness beverages as more pleasant. In addition, interest in health increased the consumption of rye breads and other whole grain breads among adolescents. The results showed that the optimal product quality in terms of intrinsic and extrinsic factors differs between individual consumers, and personal values and food choice motives can be connected to preferences for specific sensory characteristics of foods. This indicates that each food product needs to be considered in relation to its specific market niche, and to which segment of consumer will respond most positively to its characteristics.

Utilization of retention chemicals in non-wood containing furnishes

The usage of the non-wood pulps in furnishes for various paper grades is the real alternative for substitution of wood fibres in the papermaking. This is especially important now, when the prices for wood are increasing and forest resources are depleting in many regions of our planet. However, there are several problems associated with utilization of such pulps. In terms of the papermaking process one of the main problems is the poor dewatering of the non-wood pulps. This problem can be partially solved by means of retention aids. In the literature part were described technological features of the non-wood pulps as the raw materials for paper production. Moreover, overviews of the retention chemicals and methods for retention measurement were done; special attention was paid to the mechanisms of retention and drainage. Finally, factors affecting on the drainage and retention of non-wood pulps were considered holistically. Particular emphasis was put on the possibility of enzyme treatment for drainage improvement. It was stated that retention aids can significantly improve dewatering of non-wood pulps. In the experimental part the goal was to investigate influence of various microparticle retention aids on the drainage, retention and formation of furnish containing wheat straw pulp, obtained by novel pulping process (Formico™Fib). The parallel test were performed with reference furnish containing only wood pulps. It was found that Bentonite-CPAM retention aid can significantly improve drainage and retention; however formation seems be suffer from such additives. It was stated that performance of the Silica-Starch retention aid significantly depends on the starch dosing sequence and wet-end conditions; this system have shown better formation than other tested retention aids. Silica-CPAM retention aid have provided comparable results in retention and drainage with Bentonite-CPAM, while Silica-starch did not improve dewatering and yielded in lowest filler retention among other aids. Ultimately, optimal dosages for the tested retention chemicals have been suggested.

Enhancing absorptive capacity in a non-research and development. An action research approach to converting individual observations into organisational awareness

The ability to recognize potential knowledge and convert it into business opportunities is one of the key factors of renewal in uncertain environments. This thesis examines absorptive capacity in the context of non-research and development innovation, with a primary focus on the social interaction that facilitates the absorption of knowledge. It proposes that everyone is and should be entitled to take part in the social interaction that shapes individual observations into innovations. Both innovation and absorptive capacity have been traditionally related to research and development departments and institutions. These innovations need to be adopted and adapted by others. This so-called waterfall model of innovations is only one aspect of new knowledge generation and innovation. In addition to this Science–Technology–Innovation perspective, more attention has been recently paid to the Doing–Using–Interacting mode of generating new knowledge and innovations. The amount of literature on absorptive capacity is vast, yet the concept is reified. The greater part of the literature links absorptive capacity to research and development departments. Some publications have focused on the nature of absorptive capacity in practice and the role of social interaction in enhancing it. Recent literature on absorptive capacity calls for studies that shed light on the relationship between individual absorptive capacity and organisational absorptive capacity. There has also been a call to examine absorptive capacity in non-research and development environments. Drawing on the literature on employee-driven innovation and social capital, this thesis looks at how individual observations and ideas are converted into something that an organisation can use. The critical phases of absorptive capacity, during which the ideas of individuals are incorporated into a group context, are assimilation and transformation. These two phases are seen as complementary: whereas assimilation is the application of easy-to-accept knowledge, transformation challenges the current way of thinking. The two require distinct kinds of social interaction and practices. The results of this study can been crystallised thus: “Enhancing absorptive capacity in practicebased non-research and development context is to organise the optimal circumstances for social interaction. Every individual is a potential source of signals leading to innovations. The individual, thus, recognises opportunities and acquires signals. Through the social interaction processes of assimilation and transformation, these signals are processed into the organisation’s reality and language. The conditions of creative social capital facilitate the interplay between assimilation and transformation. An organisation that strives for employee-driven innovation gains the benefits of a broader surface for opportunity recognition and faster absorption.” If organisations and managers become more aware of the benefits of enhancing absorptive capacity in practice, they have reason to assign resources to those practices that facilitate the creation of absorptive capacity. By recognising the underlying social mechanisms and structural features that lead either to assimilation or transformation, it is easier to balance between renewal and effective operations.

Linear-quadratic optimal control of descriptor systems

In recent years the analysis and synthesis of (mechanical) control systems in descriptor form has been established. This general description of dynamical systems is important for many applications in mechanics and mechatronics, in electrical and electronic engineering, and in chemical engineering as well. This contribution deals with linear mechanical descriptor systems and its control design with respect to a quadratic performance criterion. Here, the notion of properness plays an important role whether the standard Riccati approach can be applied as usual or not. Properness and non-properness distinguish between the cases if the descriptor system is exclusively governed by the control input or by its higher-order time-derivatives additionally. In the unusual case of non-proper systems a quite different problem of optimal control design has to be considered. Both cases will be solved completely.

Control of Structures with Cubic and Quadratic Non-Linearities with Time Delay Consideration

This paper studies the effect of time delay on the active non-linear control of dynamically loaded flexible structures. The behavior of non-linear systems under state feedback control, considering a fixed time delay for the control force, is investigated. A control method based on non-linear optimal control, using a tensorial formulation and state feedback control is used. The state equations and the control forces are expressed in polynomial form and a performance index, quadratic in both state vector and control forces, is used. General polynomial representations of the non-linear control law are obtained and implemented for control algorithms up to the fifth order. This methodology is applied to systems with quadratic and cubic non-linearities. Strongly non-linear systems are tested and the effectiveness of the control system including a delay for the application of control forces is discussed. Numerical results indicate that the adopted control algorithm can be efficient for non-linear systems, chiefly in the presence of strong non-linearities but increasing time delay reduces the efficiency of the control system. Numerical results emphasize the importance of considering time delay in the project of active structural control systems.

Extreme Observables and Optimal Measurements in Quantum Theory

Optimization of quantum measurement processes has a pivotal role in carrying out better, more accurate or less disrupting, measurements and experiments on a quantum system. Especially, convex optimization, i.e., identifying the extreme points of the convex sets and subsets of quantum measuring devices plays an important part in quantum optimization since the typical figures of merit for measuring processes are affine functionals. In this thesis, we discuss results determining the extreme quantum devices and their relevance, e.g., in quantum-compatibility-related questions. Especially, we see that a compatible device pair where one device is extreme can be joined into a single apparatus essentially in a unique way. Moreover, we show that the question whether a pair of quantum observables can be measured jointly can often be formulated in a weaker form when some of the observables involved are extreme. Another major line of research treated in this thesis deals with convex analysis of special restricted quantum device sets, covariance structures or, in particular, generalized imprimitivity systems. Some results on the structure ofcovariant observables and instruments are listed as well as results identifying the extreme points of covariance structures in quantum theory. As a special case study, not published anywhere before, we study the structure of Euclidean-covariant localization observables for spin-0-particles. We also discuss the general form of Weyl-covariant phase-space instruments. Finally, certain optimality measures originating from convex geometry are introduced for quantum devices, namely, boundariness measuring how ‘close’ to the algebraic boundary of the device set a quantum apparatus is and the robustness of incompatibility quantifying the level of incompatibility for a quantum device pair by measuring the highest amount of noise the pair tolerates without becoming compatible. Boundariness is further associated to minimum-error discrimination of quantum devices, and robustness of incompatibility is shown to behave monotonically under certain compatibility-non-decreasing operations. Moreover, the value of robustness of incompatibility is given for a few special device pairs.

A comparison of self-determined motivational experiences between participants and non-participants following the physical activity component of the CATCH Kid Club

The CATCH Kids Club (CKC) is an after-school intervention that has attempted to address the growing obesity and physical inactivity concerns publicized in current literature. Using Self-Determination Theory (SDT: Deci & Ryan, 1985) perspective, this study's main research objective was to assess, while controlling for gender and age, i f there were significant differences between the treatment (CKC program participants) and control (non- eKC) groups on their perceptions of need satisfaction, intrinsic motivation and optimal challenge after four months of participation and after eight months of participation. For this study, data were collected from 79 participants with a mean age of9.3, using the Situational Affective State Questionnaire (SASQ: Mandigo et aI., 2008). In order to determine the common factors present in the data, a principal component analysis was conducted. The analysis resulted in an appropriate three-factor solution, with 14 items loading onto the three factors identified as autonomy, competence and intrinsic motivation. Initially, a multiple analysis of co-variance (MANCOY A) was conducted and found no significant differences or effects (p> 0.05). To further assess the differences between groups, six analyses of co-variance (ANeOY As) were conducted, which also found no significant differences (p >0 .025). These findings suggest that the eKC program is able to maintain the se1fdetermined motivational experiences of its participants, and does not thwart need satisfaction or self-determined motivation through its programming. However, the literature suggests that the CKe program and other P A interventions could be further improved by fostering participants' self-determined motivational experiences, which can lead to the persistence of healthy PA behaviours (Kilpatrick, Hebert & Jacobsen, 2002).

The Alberta Dilemma: Optimal Sharing of a Water Resource by an Agricultural and an Oil Sector

The purpose of this paper is to characterize the optimal time paths of production and water usage by an agricultural and an oil sector that have to share a limited water resource. We show that for any given water stock, if the oil stock is sufficiently large, it will become optimal to have a phase during which the agricultural sector is inactive. This may mean having an initial phase during which the two sectors are active, then a phase during which the water is reserved for the oil sector and the agricultural sector is inactive, followed by a phase during which both sectors are active again. The agricultural sector will always be active in the end as the oil stock is depleted and the demand for water from the oil sector decreases. In the case where agriculture is not constrained by the given natural inflow of water once there is no more oil, we show that oil extraction will always end with a phase during which oil production follows a pure Hotelling path, with the implicit price of oil net of extraction cost growing at the rate of interest. If the natural inflow of water does constitute a constraint for agriculture, then oil production never follows a pure Hotelling path, because its full marginal cost must always reflect not only the imputed rent on the finite oil stock, but also the positive opportunity cost of water.

On the Optimal Order of Natural Resource Use When the Capacity of the Inexhaustible Substitute is Limited.

Consider a general equilibrium framework where the marginal cost of extraction from several deposits of an exhaustible resource is constant in terms of an inexhaustible perfect substitute and differs between deposits. the instantaneous rate of production form the inexhaustible resource is subject to a capacity constraint.

L'élastographie ultrasonore dynamique vasculaire : une nouvelle modalité d'imagerie non-invasive pour la caractérisation mécanique de la thrombose veineuse

L’accident thromboembolique veineux, tel que la thrombose veineuse profonde (TVP) ou thrombophlébite des membres inférieurs, est une pathologie vasculaire caractérisée par la formation d’un caillot sanguin causant une obstruction partielle ou totale de la lumière sanguine. Les embolies pulmonaires sont une complication mortelle des TVP qui surviennent lorsque le caillot se détache, circule dans le sang et produit une obstruction de la ramification artérielle irriguant les poumons. La combinaison d’outils et de techniques d’imagerie cliniques tels que les règles de prédiction cliniques (signes et symptômes) et les tests sanguins (D-dimères) complémentés par un examen ultrasonographique veineux (test de compression, écho-Doppler), permet de diagnostiquer les premiers épisodes de TVP. Cependant, la performance de ces outils diagnostiques reste très faible pour la détection de TVP récurrentes. Afin de diriger le patient vers une thérapie optimale, la problématique n’est plus basée sur la détection de la thrombose mais plutôt sur l’évaluation de la maturité et de l’âge du thrombus, paramètres qui sont directement corrélées à ses propriétés mécaniques (e.g. élasticité, viscosité). L’élastographie dynamique (ED) a récemment été proposée comme une nouvelle modalité d’imagerie non-invasive capable de caractériser quantitativement les propriétés mécaniques de tissus. L’ED est basée sur l’analyse des paramètres acoustiques (i.e. vitesse, atténuation, pattern de distribution) d’ondes de cisaillement basses fréquences (10-7000 Hz) se propageant dans le milieu sondé. Ces ondes de cisaillement générées par vibration externe, ou par source interne à l’aide de la focalisation de faisceaux ultrasonores (force de radiation), sont mesurées par imagerie ultrasonore ultra-rapide ou par résonance magnétique. Une méthode basée sur l’ED adaptée à la caractérisation mécanique de thromboses veineuses permettrait de quantifier la sévérité de cette pathologie à des fins d’amélioration diagnostique. Cette thèse présente un ensemble de travaux reliés au développement et à la validation complète et rigoureuse d’une nouvelle technique d’imagerie non-invasive élastographique pour la mesure quantitative des propriétés mécaniques de thromboses veineuses. L’atteinte de cet objectif principal nécessite une première étape visant à améliorer les connaissances sur le comportement mécanique du caillot sanguin (sang coagulé) soumis à une sollicitation dynamique telle qu’en ED. Les modules de conservation (comportement élastique, G’) et de perte (comportement visqueux, G’’) en cisaillement de caillots sanguins porcins sont mesurés par ED lors de la cascade de coagulation (à 70 Hz), et après coagulation complète (entre 50 Hz et 160 Hz). Ces résultats constituent les toutes premières mesures du comportement dynamique de caillots sanguins dans une gamme fréquentielle aussi étendue. L’étape subséquente consiste à mettre en place un instrument innovant de référence (« gold standard »), appelé RheoSpectris, dédié à la mesure de la viscoélasticité hyper-fréquence (entre 10 Hz et 1000 Hz) des matériaux et biomatériaux. Cet outil est indispensable pour valider et calibrer toute nouvelle technique d’élastographie dynamique. Une étude comparative entre RheoSpectris et la rhéométrie classique est réalisée afin de valider des mesures faites sur différents matériaux (silicone, thermoplastique, biomatériaux, gel). L’excellente concordance entre les deux technologies permet de conclure que RheoSpectris est un instrument fiable pour la mesure mécanique à des fréquences difficilement accessibles par les outils actuels. Les bases théoriques d’une nouvelle modalité d’imagerie élastographique, nommée SWIRE (« shear wave induced resonance dynamic elastography »), sont présentées et validées sur des fantômes vasculaires. Cette approche permet de caractériser les propriétés mécaniques d’une inclusion confinée (e.g. caillot sanguin) à partir de sa résonance (amplification du déplacement) produite par la propagation d’ondes de cisaillement judicieusement orientées. SWIRE a également l’avantage d’amplifier l’amplitude de vibration à l’intérieur de l’hétérogénéité afin de faciliter sa détection et sa segmentation. Finalement, la méthode DVT-SWIRE (« Deep venous thrombosis – SWIRE ») est adaptée à la caractérisation de l’élasticité quantitative de thromboses veineuses pour une utilisation en clinique. Cette méthode exploite la première fréquence de résonance mesurée dans la thrombose lors de la propagation d’ondes de cisaillement planes (vibration d’une plaque externe) ou cylindriques (simulation de la force de radiation par génération supersonique). DVT-SWIRE est appliquée sur des fantômes simulant une TVP et les résultats sont comparés à ceux donnés par l’instrument de référence RheoSpectris. Cette méthode est également utilisée avec succès dans une étude ex vivo pour l’évaluation de l’élasticité de thromboses porcines explantées après avoir été induites in vivo par chirurgie.

Pharmacothérapie de la douleur chronique non cancéreuse chez des patients suivis en première ligne

Introduction : La douleur chronique non cancéreuse (DCNC) est prévalente, notamment en première ligne où l’on traite la plupart des maladies chroniques. Cette étude de cohorte vise à décrire l’usage des analgésiques, la prévalence et le traitement des effets secondaires des analgésiques utilisés, la satisfaction ainsi que les croyances et attitudes face à la douleur et son traitement chez des patients souffrant de DCNC et suivis en première ligne. Méthodologie : Des patients souffrant de DCNC (douleur qui dure depuis six mois et plus), ressentie au minimum deux fois par semaine avec une intensité d’au moins 4 sur une échelle de 0 à 10 (10 = la pire douleur possible) et qui possèdent une ordonnance active d’un médecin de famille pour un médicament contre la douleur, ont été recrutés à travers le Québec. Ils ont complété une entrevue téléphonique et un questionnaire auto-administré afin de documenter les caractéristiques de leur douleur, son impact psychosocial et émotionnel ainsi que leur satisfaction et croyances face à la douleur et son traitement. L’information concernant la pharmacothérapie reçue a été collectée en utilisant les banques de données administratives de la Régie d’assurance maladie du Québec et les dossierspatients des pharmacies communautaires. Résultats : Les 486 patients qui ont participé à l’étude avaient une moyenne d’âge de 58,4 ans. Ils ont rapporté une douleur qui dure en moyenne depuis 11,7 ans évaluée à 6,5 sur une échelle de 0 à 10. Sur la période d’une année, 52,9% des patients ont reçu des analgésiques prescrits par deux ou trois médecins de famille. Les analgésiques les plus dispensés étaient les anti-inflammatoires non stéroïdiens (72,2%) et les opioïdes (65,6%). Bien que 90% des patients ont rapporté des effets gastro-intestinaux, les proportions de ceux n’ayant pas reçu de médicaments pour soulager la constipation ou les nausées et/ou vomissements étaient respectivement 36,4% et 54,4%. Le niveau de satisfaction était faible, notamment face à l’information reçue concernant la douleur et son traitement. La peur des effets néfastes des analgésiques constitue la barrière face à l’optimisation de la pharmacothérapie de la douleur la plus souvent rapportée par les patients. Conclusion : En première ligne, la prise en charge de la douleur chronique non cancéreuse modérée à sévère paraît sous-optimale. Elle implique différents médecins de famille suggérant un manque de cohérence et de continuité. Les effets secondaires aux analgésiques sont prévalents et souvent non traités; la satisfaction est faible et les patients paraissent réticents à prendre les médicaments contre la douleur. Ces résultats indiquent clairement la nécessité d’optimiser la pharmacothérapie de ces patients.

Le développement de l'identité professionnelle en formation infirmière par l'enseignement optimal des conceptions infirmières

Travail dirigé présenté à la Faculté des Sciences Infirmières En vue de l’obtention du grade de Maîtrise ès Sciences (M. Sc.) Option formation en sciences infirmière.

Positionnement optimal de l'activité physique pour profiter de l'effet anorexigène

La balance énergétique (dépense énergétique et ingestion calorique) est au centre du contrôle de la masse corporelle. L’activité physique peut par ailleurs réduire l’appétit et l’ingestion calorique, un phénomène qu’on appelle aussi l’effet anorexigène de l’activité physique. Cependant, l’hormone orexigénique, liée à une diminution de l’appétit, diminue pendant l’exercice pour remonter rapidement après l’effort. Le but de ce mémoire était de déterminer si l’ingestion calorique est réduite quand l’exercice précède immédiatement le repas comparativement à une condition où il y a une pause entre l’exercice et le repas. Pour ce faire, douze garçons non obèses (15-20 ans) ont pris part à l’étude. Chaque participant était évalué individuellement pour les deux tâches suivantes, et ce, dans un ordre aléatoire : 1) Ex = 30 minutes d’exercice (70% VO2max) suivi immédiatement par un buffet à volonté à midi; 2) Expause = 30 minutes d’exercice (70% VO2max) suivi d’une pause de 135 minutes et d’un buffet à volonté à midi. Les visites étaient précédées par un déjeuner standard et complétées avec une collation à volonté durant l’après-midi et un souper type buffet à volonté pour souper. Alors que les résultats ont révélé que la faim était similaire en tout temps, l’ingestion calorique au diner était plus basse pour la condition Ex que pour la condition Expause (5 072 vs 5 718 kJ; p < 0,05). Aucune différence significative n’a été notée pour la collation de l’après-midi et le souper. Chose intéressante, l’ingestion calorique des lipides était plus basse au diner avec une ingestion de 1 604 kJ pour la condition Ex versus 2 085 kJ pour la condition Expause (p < 0,05). Cette étude est la première à investiguer l’effet du positionnement optimal de l’activité physique pour réduire l’ingestion calorique et elle révèle qu’être actif physiquement juste avant le repas joue un rôle sur la diminution de l’ingestion calorique indépendamment des sensations d’appétit. L’absence d’une compensation durant le reste de la journée suggère de plus qu’une balance énergétique négative, incluant une réduction de la consommation de lipides, peut être plus facilement atteinte en positionnant l’activité physique juste avant un repas.