Application of rare earths in thermal barrier coating materials

Rare earths are a series of minerals with special properties that make them essential for applications including miniaturized electronics, computer hard disks, display panels, missile guidance, pollution controlling catalysts, H-2-storage and other advanced materials. The use of thermal barrier coatings (TBCs) has the potential to extend the working temperature and the life of a gas turbine by providing a layer of thermal insulation between the metallic substrate and the hot gas. Yttria (Y2O3), as one of the most important rare earth oxides, has already been used in the typical TBC material YSZ (yttria stabilized zirconia). In the development of the TBC materials, especially in the latest ten years, rare earths have been found to be more and more important. All the new candidates of TBC materials contain a large quantity of rare earths, such as R2Zr2O7 (R=La, Ce, Nd, Gd), CeO2-YSZ, RMeAl11O19 (R=La, Nd; Me=Mg, Ca, Sr) and LaPO4. The concept of double-ceramic-layer coatings based on the rare earth materials and YSZ is effective for the improvement of the thermal shock life of TBCs at high temperature.

White polymeric light-emitting diodes with high color rendering index

The efficient white polymeric light-emitting diodes based on a white emissive polymer doped with a red phosphorescent dopant were fabricated by spin-coating method. The emission spectrum of the device is broadened to cover the full visible region by doping the red phosphorescent dye and thereby realizes white emission with high color-rendering index (CRI). By controlling the contents of the doped electron-transporting 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole and the red phosphorescent dopant, a luminous efficiency as high as 5.3 cd/A and a power efficiency of 3 lm/W were obtained with a CRI of 92.

The thermal cycling behavior of Lanthanum-Cerium Oxide thermal barrier coating prepared by EB-PVD

Bulk material and coatings of Lanthanum-Cerium Oxide (La2Ce2O7) with a fluorite structure were studied as a candidate material for thermal barrier coating (TBC). It has been showed that such material has the properties of low thermal conductivity about four times lower than YSZ, the difference in the thermal expansion coefficient between La2Ce2O7 and bond coat is smaller than that of YSZ in TBC systems, high phase stability between room temperature and 1673 K, about 300 K higher than that of the YSZ. The coating prepared by electron beam physical vapor deposition (EB-PVD) showed that it has good thermal cycling behavior, implying that Such material can be a promising thermal barrier coating material. The deviation of coating composition from ingot can be overcome by the addition of excess La2O3 during ingot preparation and/or by adjusting the process parameters.

High-efficiency spin-coated organic light-emitting diodes based on a europium complex

An organic light-emitting diode fabricated by doping a europium, complex tris(dibiphenoylmethane)-mono (phenanthroline)-europium (Eu(DBPM)(3) (Phen)) into polymer poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene) and poly(N-carbazole) was realized by spin coating. Comparison with other europium complexes, due to the existence of a larger spectral overlap between Eu(DBPM)(3)(Phen) and poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4phenylene), a high efficiency red emission was achieved. The device showed a turn-on voltage of 5.2 V The maximum efficiency reached 0.47 cd/A at luminance of 50 cd/m(2). The maximum luminance can reach 150 cd/m(2) at 95 mA/cm(2). To the best of our knowledge, this is one of the best results based on europium complexes by spin-casting method.

Improving Photovoltaics with High Luminescence Efficiency Quantum Dot Layers

A solar cell relies on its ability to turn photons into current. Because short wavelength photons are typically absorbed near the top surface of a cell, the generated charge carriers recombine before being collected. But when a layer of quantum dots (nanoscale semiconductor particles) is placed on top of the cell, it absorbs short wavelength photons and emits them into the cell at longer wavelengths, which enables more efficient carrier collection. However, the resulting power conversion efficiency of the system depends critically on the quantum dot luminescence efficiency – the nature of this relationship was previously unknown. Our calculations suggest that a quantum dot layer must have high luminescence efficiency (at least 80%) to improve the current output of existing photovoltaic (PV) cells; otherwise, it may worsen the cell’s efficiency. Our quantum dot layer (using quantum dots with over 85% quantum yield) slightly reduced the efficiency of our PV cells. We observed a decrease in short circuit current of a commercial-grade cell from 0.1977 A to 0.1826 A, a 7.6% drop, suggesting that improved optical coupling from the quantum dot emission into the solar cell is needed. With better optical coupling, we predict current enhancements between ~6% and ~8% for a solar cell that already has an antireflection coating. Such improvements could have important commercial impacts if the coating could be deployed in a scalable fashion.

Conformal oxide coating of carbon nanotubes

The International Roadmap for Ferroelectric Memories requires three-dimensional integration of high-dielectric materials onto metal interconnects or bottom electrodes by 2010. Here, we demonstrate the possibility of conformally coating carbon nanotubes with high-dielectric oxide as a first step toward ultrahigh integration density of three-dimensional ferroelectric random access memories.

Comparison of techniques to screen and characterize bacteria-specific hybridomas for high-quality monoclonal antibodies selection

Antibodies are are very important materials for diagnostics. A rapid and simple hybridoma screening method will help in delivering specific monoclonal antibodies. In this study, we systematically developed the first antibody array to screen for bacteria-specific monoclonal antibodies using Listeria monocytogenes as a bacteria model. The antibody array was developed to expedite the hybridoma screening process by printing hybridoma supernatants on a glass slide coated with an antigen of interest. This screening method is based on the binding ability of supernatants to the coated antigen. The bound supernatants were detected by a fluorescently labeled anti-mouse immunoglobulin. Conditions (slide types, coating, spotting, and blocking buffers) for antibody array construction were optimized. To demonstrate its usefulness, antibody array was used to screen a sample set of 96 hybridoma supernatants in comparison to ELISA. Most of the positive results identified by ELISA and antibody array methods were in agreement except for those with low signals that were undetectable by antibody array. Hybridoma supernatants were further characterized with surface plasmon resonance to obtain additional data on the characteristics of each selected clone. While the antibody array was slightly less sensitive than ELISA, a much faster and lower cost procedure to screen clones against multiple antigens has been demonstrated. (C) 2011 Elsevier Inc. All rights reserved.

Alternative method for producing organic fertiliser from anaerobic digestion liquor and limestone powder:High Shear wet granulation

Generally, the solid and liquid fractions (digestate) from Anaerobic Digestion (AD) energy production are considered as waste. This has a negative impact on the sustainability of AD processes because of the financial outlay required to treat digestate before being discharged into municipal water treatment plants or natural water bodies. The main aim of this research was to investigate feasibility of producing an organic fertiliser using anaerobic digestate and limestone powders as the raw materials employing a high shear granulation process. Two-level factorial experimental design was used to determine the influence of granulation process variables on, the strength, resistance to attrition and yield of the granules. It was concluded from the study that it is technically feasible to produce organic fertiliser granules of acceptable strength and product yield. Increasing the liquid-to-solid ratio during granulation leads to increased granule strength and better product yield. Although the strength of the granules produced was lower than typical strength of commercial synthetic fertiliser granules (about 5 to 7. MPa), this could be improved by mixing the digestate with a polymeric binder or coating the particles post granulation. © 2012 Elsevier B.V.

The influence of high-temperature sintering on microstructure and mechanical properties of free-standing APS CeO-YO -ZrO coatings

In this study, ceria-yttria co-stabilized zirconia (CYSZ) free-standing coatings, deposited by air plasma spraying (APS), were isothermally annealed at 1315 °C in order to explore the effect of sintering on the microstructure and the mechanical properties (i.e., hardness and Young's modulus). To this aim, coating microstructure, before and after heat treatment, was analyzed using scanning electron microscopy, and image analysis was carried out in order to estimate porosity fraction. Moreover, Vickers microindentation and depth-sensing nanoindentation tests were performed in order to study the evolution of hardness and Young's modulus as a function of annealing time. The results showed that thermal aging of CYSZ coatings leads to noticeable microstructural modifications. Indeed, the healing of finer pores, interlamellar, and intralamellar microcracks was observed. In particular, the porosity fraction decreased from ~10 to ~5% after 50 h at 1315 °C. However, the X-ray diffraction analyses revealed that high phase stability was achieved, as no phase decomposition occurred after thermal aging. In turn, both the hardness and Young's modulus increased, in particular, the increase in stiffness (with respect to "as produced" samples) was equal to ~25%, whereas the hardness increased to up to ~60%. © 2010 Springer Science+Business Media, LLC.

Development of a Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) Cell for the In Situ Analysis of Co-Electrolysis in a Solid Oxide Cell

Co-electrolysis of carbon dioxide and steam has been shown to be an efficient way to produce syngas, however further optimisation requires detailed understanding of the complex reactions, transport processes and degradation mechanisms occurring in the solid oxide cell (SOC) during operation. Whilst electrochemical measurements are currently conducted in situ, many analytical techniques can only be used ex situ and may even be destructive to the cell (e.g. SEM imaging of microstructure). In order to fully understand and characterise co-electrolysis, in situ monitoring of the reactants, products and SOC is necessary. Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) is ideal for in situ monitoring of co-electrolysis as both gaseous and adsorbed CO and CO2 species can be detected, however it has previously not been used for this purpose. The challenges of designing an experimental rig which allows optical access alongside electrochemical measurements at high temperature and operates in a dual atmosphere are discussed. The rig developed has thus far been used for symmetric cell testing at temperatures from 450[degree]C to 600[degree]C. Under a CO atmosphere, significant changes in spectra were observed even over a simple Au|10Sc1CeSZ|Au SOC. The changes relate to a combination of CO oxidation, the water gas shift reaction and carbonate formation and decomposition processes, with the dominant process being both potential and temperature dependent.

Assessment of the Activity of Photocatalytic Paint Using a Simple Smart Ink Designed for High Activity Surfaces

The use of an acid violet 7 (AV7) smart ink to assess the activity of photocatalytic paint is demonstrated. A linear correlation is established between the change in oxidized dye concentration, as measured by diffuse reflectance, and the change in the green component of the RGB color values, obtained using a portable hand-held scanner, suggesting that such tests can be monitored easily using an inexpensive piece of hand-held office equipment, as opposed to an expensive lab-based instrument, such as a diffuse reflectance UV/vis spectrophotometer. The bleaching of the AV7 follows first order kinetics, at a rate that is linearly dependent upon the UVA irradiance (0.30–3.26 mW cm–2). A comparison of relative rate of bleaching of the AV7 ink with the relative rate of removal of NOx, as determined using the ISO test (ISO 22197-1:2007), established a linear relationship between the two sets of results and the relevance of this correlation is discussed briefly.

Facile synthesis of nanocrystalline LiFePO4/graphene composite as cathode material for high power lithium ion batteries

We describe a simple strategy, which is based on the idea of space confinement, for the synthesis of carbon coating on LiFePO₄ nanoparticles/graphene nanosheets composites in a water-in-oil emulsion system. The prepared composite displayed high performance as a cathode material for lithium-ion battery, such as high reversible lithium storage capacity (158 mA h g^-1 after 100 cycles), high coulombic efficiency (over 97%), excellent cycling stability and high rate capability (as high as 83 mA h g ^-1 at 60 C). Very significantly, the preparation method employed can be easily adapted and be extended as a general approach to sophisticated compositions and structures for the preparation of highly dispersed nanosized structure on graphene. 

Zero-Reflectance Metafilms for Optimal Plasmonic Sensing

An ultrathin layer of metasurface that almost completely annihilates the reflection of light (>99.5%) over a wide range of incident angles (>80°) is experimentally demonstrated. Such zero-reflectance metafilms exhibit optimal performance for plasmonic sensing, since their sensitivity to changes of local refractive index is far superior to films of nonzero reflectance. Since both main detection mechanisms tracking intensity changes and wavelength shifts are improved, zero-reflectance metafilms are optimal for localized surface plasmon resonance molecular sensing. Such nanostructures have significant opportunities in many areas, including enhanced light harvesting as well as in developing high-performance molecular sensors for a wide range of chemical and biomedical applications.

Preparation of new materials by heterogeneous modification of cellulose

O presente trabalho teve como principal objectivo estudar a modificação química heterogénea controlada de fibras de celulose com diferentes reagentes de modo a alterar as suas propriedades de superfície, em especial em termos da criação de um carácter hidrofóbico e lipofóbico, preservando, sempre que possível, as suas propriedades mecânicas e, consequentemente, abrindo novas perspectivas de aplicação. O desenvolvimento do trabalho envolveu três abordagens principais, envolvendo, em cada caso, o estudo de diferentes condições reaccionais. Na primeira abordagem foram utilizados como reagentes de modificação compostos perfluorados, nomeadamente o anidrido trifluoroacético (TFAA), o cloreto de 2,3,4,5,6-pentafluorobenzoílo (PFBz) e o cloreto de 3,3,3- trifluoropropanoílo (TFP), para promover a acilação heterogénea da superfície das fibras. A segunda estratégia usada consistiu na preparação de híbridos de celulose do tipo orgânico-inorgânico classe-II, através da modificação das fibras de celulose com o (3-isocianatopropil)trietoxissilano (ICPTEOS), um reagente organossilano bifuncional. A ligação às fibras de celulose foi efectuada através das funções isocianato e, posteriormente, os grupos etoxissilano foram sujeitos a tratamentos de hidrólise ácida, como tal ou na presença de outros siloxanos, nomeadamente o tetraetoxissilano (TEOS) e o 1H,1H,2H,2Hperfluorodeciltrietoxissilano (PFDTEOS). Finalmente, a última abordagem foi baseada na modificação das fibras com triclorometilssilano (TCMS), através de uma reacção gás-sólido, que dispensou assim o uso de solventes orgânicos. A ocorrência de modificação química foi em cada caso confirmada por Espectroscopia de Infravermelho com Transformada de Fourier e Reflectância Total Atenuada (FTIR-ATR), Análise Elementar (EA) e determinação de ângulos de contacto. Adicionalmente, e dependendo de cada caso específico, diversas outras técnicas foram empregues na caracterização aprofundada dos materiais preparados, nomeadamente Ressonância Magnética Nuclear CPMAS no Estado Sólido (RMN), Espectroscopia de Difracção de Raios-X (XRD), Análise Termogravimétrica (TGA), Espectrometria de Massa de Iões Secundários com Análise de Tempo de Vôo (ToF-SIMS), Espectroscopia Fotoelectrónica de Raios-X (XPS) e Microscopia Electrónica de Varrimento (SEM). Relativamente à acilação das fibras de celulose com reagentes perfluorados, o sucesso da reacção foi comprovado por FTIR-ATR, EA, XPS e ToF-SIMS. Neste contexto, obtiveram-se fibras modificadas possuindo graus de substituição (DS) compreendidos entre 0.006 e 0.39. Verificou-se por XRD que, em geral, mesmo para os valores de DS mais elevados, a cristalinidade das fibras não foi afectada, indicando que a modificação foi limitada às camadas mais superficiais das mesmas ou a regiões amorfas das suas camadas mais internas. Adicionalmente, observou-se por ToF-SIMS que a distribuição dos grupos perfluorados à superfície das fibras foi, de facto, bastante heterogénea. Todos os derivados de celulose perfluorados apresentaram elevada hidrofobicidade e lipofobicidade, tendo-se atingido ângulos de contacto com água e diiodometano de 126º e 104º, respectivamente. Um aspecto interessante relativo a estes materiais é que a elevada omnifobicidade foi observada mesmo para valores de DS muito reduzidos, não se mostrando significativamente afectada pelo aumento dos mesmos. Em consonância, verificou-se por XPS que a cobertura da superfície das fibras de celulose com grupos perfluorados aumentou apenas ligeiramente com o aumento do DS, apontando para a esterificação de camadas mais internas das fibras, associada, neste caso, predominantemente aos seus domínios amorfos. No que diz respeito à estabilidade hidrolítica destes derivados, obtiveram-se dois tipos distintos de comportamento. Por um lado, as fibras de celulose trifluoroacetiladas são facilmente hidrolisáveis em meio neutro, e, por outro, as fibras pentafluorobenzoiladas e trifluoropropanoiladas mostram-se bastante resistentes face a condições de hidrólise em meio neutro e ácido (pH 4), podendo, contudo, ser facilmente hidrolisadas em meio alcalino (pH 9 e 12, para derivados do PFBz e do TFP, respectivamente). Na segunda abordagem verificou-se a ocorrência de reacção por FTIR-ATR e EA. Em geral, a modificação química com ICPTEOS ocorre predominantemente nas zonas mais superficiais das fibras de celulose ou em regiões amorfas. Contudo, em condições reaccionais mais severas (maior quantidade de reagente e tempo de reacção), esta atingiu também regiões cristalinas, afectando, consequentemente, a estrutura cristalina das fibras, como verificado por XRD. Por RMN de 29Si observou-se que após reacção com o ICPTEOS já existiam indícios de alguma hidrólise dos grupos etoxissilano, e que a sua subsequente condensação parcial tinha levado à formação de uma película inorgânica em redor das fibras (verificado por SEM), constituída maioritariamente por estruturas lineares, com uma contribuição mais modesta de estruturas “diméricas” e outras mais ramificadas. Consequentemente, este revestimento inorgânico transformou as fibras de celulose em materiais híbridos com elevada hidrofobicidade (ângulos de contacto com água entre 103-129º). A hidrólise ácida dos restantes grupos etoxissilano, como tal ou na presença de TEOS, originou híbridos de celulose com elevada hidrofilicidade, sendo impossível medirem-se os ângulos de contacto com água dos produtos finais, devido à presença maioritária de grupos silanol (Si-OH) e ligações Si-O-Si à superfície, os quais contribuíram para o consequente aumento de energia de superfície. No entanto, quando a hidrólise foi realizada na presença de PFDTEOS, obtiveram-se materiais híbridos com elevada hidrofobicidade e lipofobicidade (ângulos de contacto com água e diiodometano de 140º e 134º, respectivamente), devido à combinação da presença de grupos perfluorados e micro- e nano-rugosidades na superfície das fibras de celulose, conforme confirmado por SEM. Finalmente, a última abordagem permitiu preparar materiais derivados de celulose altamente hidrofóbicos e lipofóbicos (ângulos de contacto com água e diiodometano de 136º e 109º, respectivamente) por um processo simples, envolvendo tempos de tratamento tão curtos como 0.5 min. Este comportamento omnifóbico foi gerado pelo efeito sinergético entre a diminuição de energia de superfície das fibras, devido à presença de grupos metilo dos resíduos de TCMS ligados a estas, e a condensação dos resíduos de TCMS na forma de micro- e nano-partículas inorgânicas, que levou à criação de um revestimento rugoso à superfície das fibras, conforme observado por RMN de 29Si e SEM, respectivamente. A pré-humidificação das fibras de celulose demonstrou desempenhar um importante papel de “acelerador” dos processos de hidrólise e condensação das moléculas de TCMS. Nestas condições, o tempo de tratamento foi um dos parâmetros mais relevantes, pois para tempos de tratamento muito curtos (0.5 min) os materiais resultantes não apresentaram quaisquer diferenças a nível de propriedades físico-químicas em relação ao substrato de partida (a humidade em excesso consumiu todo o TCMS antes que este conseguisse reagir com os grupos hidroxilo das fibras de celulose), possuindo, por exemplo, valores de ângulos de contacto com água idênticos. Para tempos de tratamento mais longos, como 30 min, os materiais finais apresentaram a maior quantidade de componentes inorgânicos, tal como verificado por EA e TGA. Assim, o controlo da humidade das fibras é imperativo para se poder moldar as propriedades finais dos produtos. Esta última abordagem é particularmente promissora uma vez que tem como base um sistema simples e “verde” que pode ser facilmente implementado. Em conclusão, este trabalho permitiu demonstrar que a modificação química heterogénea controlada das fibras de celulose representa uma iniciativa promissora para a preparação de novos materiais obtidos a partir de recursos renováveis, com propriedades interessantes e passíveis de ser potencialmente aplicados em diferentes áreas. Para além do mais, as estratégias de modificação estudadas podem também ser precursoras de novos estudos que possam vir a ser desenvolvidos dentro do mesmo âmbito.

Far infrared reflectance and optical properties of organic superconductor (TMTSF)2ClO4 /

Polarized reflectance measurements of the quasi I-D charge-transfer salt (TMTSFh CI04 were carried out using a Martin-Puplett-type polarizing interferometer and a 3He refrigerator cryostat, at several temperatures between 0.45 K and 26 K, in the far infrared, in the 10 to 70 cm- 1 frequency range. Bis-tetramethyl-tetraselena-fulvalene perchlorate crystals, grown electrochemically and supplied by K. Behnia, of dimensions 2 to 4 by 0.4 by 0.2 mm, were assembled on a flat surface to form a mosaic of 1.5 by 3 mm. The needle shaped crystals were positioned parallel to each other along their long axis, which is the stacking direction of the planar TMTSF cations, exposing the ab plane face (parallel to which the sheets of CI04 anions are positioned). Reflectance measurements were performed with radiation polarized along the stacking direction in the sample. Measurements were carried out following either a fast (15-20 K per minute) or slow (0.1 K per minute) cooling of the sample. Slow cooling permits the anions to order near 24 K, and the sample is expected to be superconducting below 1.2 K, while fast cooling yields an insulating state at low temperatures. Upon the slow cooling the reflectance shows dependence with temperature and exhibits the 28 cm- 1 feature reported previously [1]. Thermoreflectance for both the 'slow' and 'fast' cooling of the sample calculated relative to the 26 K reflectance data indicates that the reflectance is temperature dependent, for the slow cooling case only. A low frequency edge in the absolute reflectance is assigned an electronic origin given its strong temperature dependence in the relaxed state. We attribute the peak in the absolute reflectance near 30 cm-1 to a phonon coupled to the electronic background. Both the low frequency edge and the 30 cm-1 feature are noted te shift towards higher frequcncy, upon cntering the superconducting state, by an amount of the order of the expected superconducting energy gap. Kramers-Kronig analysis was carried out to determine the optical conductivity for the slowly cooled sample from the measured reflectance. In order to do so the low frequency data was extrapolated to zero frequency using a Hagen-Ru bens behaviour, and the high frequency data was extended with the data of Cao et al. [2], and Kikuchi et al. [3]. The real part of the optical conductivity exhibits an asymmetric peak at 35 cm-1, and its background at lower frequencies seems to be losing spectral weight with lowering of the temperature, leading us to presume that a narrow peak is forming at even lower frequencies.