Equilateral-Triangle and Square Resonator Semiconductor Microlasers

The characteristics of equilateral-triangle resonator (ETR) and square resonator microlasers are reported, which are potential light sources in the photonic integrations. Based on the numerical simulations, we find that high-efficiency directional emission can be achieved for the triangle and square microlasers by directly connecting an output waveguide to the resonators. The electrically injected InP/InGaAsP ETR and square resonator microlasers with a 2-mu m-wide output waveguide were fabricated by standard photolithography and inductively coupled plasma etching techniques. Room-temperature continuous-wave (CW) operations were achieved for the ETR microlasers with the side length from 10 to 30 mu m and the square resonator microlasers with the side length of 20 mu m. The output power versus CW injection current and the laser spectra are presented for an ETR microlaser up to 310 K and a square resonator microlaser to 305 K. The lasing spectra with mode wavelength intervals as that of whispering-gallery-type modes and Fabry-Perot modes are observed for two square lasers, which can lase at low temperature and room temperature, respectively.

Design and realization of a microracetrack resonator based polarization splitter in silicon-on-insulator

An efficient polarization splitter based on a microracetrack resonator in silicon-on-insulator has been designed and realized using electron beam lithography and inductively coupled plasma etching. Polarization-dependent waveguides and the microracetrack resonator are combined and exploited to split two orthogonal polarizations. Rib waveguides are employed to enhance the coupling efficiency for the transverse-electric mode and endow the resonator with high performance for both polarizations. In experiments, a splitting ratio has been achieved of about 20 dB at the drop port around 1550 nm for each extracted polarization, in good agreement with the prediction.

Investigation of mode coupling in a microdisk resonator for realizing directional emission

Mode coupling between the whispering-gallery modes (WGMs) is numerically investigated for a two-dimensional microdisk resonator with an output waveguide. The equilateral-polygonal shaped mode patterns can be constructed by mode coupling in the microdisk, and the coupled modes can still keep high quality factors (Q factors). For a microdisk with a diameter of 4.5 mu m and a refractive index of 3.2 connected to a 0.6-mu m-wide output waveguide, the coupled mode at the wavelength of 1490 nm has a Q factor in the order of 10(4), which is ten times larger than those of the uncoupled WGMs, and the output efficiency defined as the ratio of the energy flux confined in the output waveguide to the total radiation energy flux is about 0.65. The mode coupling can be used to realize high efficiency directional-emission microdisk lasers. (C) 2009 Optical Society of America

Mode Analysis for Equilateral-Triangle-Resonator Microlasers with Metal Confinement Layers

Mode characteristics are analyzed for electrically injected equilateral-triangle-resonator (ETR) semiconductor microlasers, which are laterally confined by insulating barrier SiO2 and electrode metals Ti-Au. For the ETR without metal layers, the totally confined mode field patterns are derived based on the reflection phase shifts, and the Q-factors are calculated from the far-field emission of the analytical near field distribution, which are agreement very well with the numerical results of the finite-difference time-domain (FDTD) simulation. The polarization dependence reflections for light rays incident on semiconductor-SiO2 -Ti-Au multi-layer structures are accounted in considering the confinement of TE and TM modes in the ETR with the metal layers. The reflectivity will greatly reduce with a Ti layer between SiO2 and Au for light rays with incident angle less than 30 especially for the TE mode, even the thickness of the Ti layer is only 10 nm. If the ETR is laterally confined by SiO2-Au layers without the Ti layer, the Fabry-Perot type modes with an incident angle of zero on one side of the ETR can also have high Q-factor. The FDTD simulation for the ETR confined by metal layers verifies the above analysis based on multi-layer reflections. The output spectra with mode intervals of whispering-gallery modes and Fabry-Perot type modes are observed from different ETR lasers with side length of 10 m, respectively.

Analysis of modes in a freestanding microsquare resonator by 3-D finite-difference time-domain

Modes in a microsquare resonator slab with strong vertical waveguide consisting of air/semiconductor/air are analyzed by three-dimensional (3-D) finite-difference time-domain simulation, and compared with that of two-dimensional (2-D) simulation under effective index approximation. Mode frequencies and field distributions inside the resonator obtained by the 3-D simulation are in good agreement with those of the 2-D approximation. However, field distributions at the boundary of the resonator obtained by 3-D simulation are different from that of the 2-D simulation, especially the vertical field distribution near the boundary is great different from that of the slab waveguide, which is used in the effective index approximation. Furthermore the quality factors obtained by 3-D simulation are much larger. than that by 2-D simulation for the square resonator slab with the strong vertical waveguide.

Room-temperature continuous-wave electrically injected InP-GaInAsP equilateral-triangle-resonator lasers

Equilateral-triangle-resonator (ETR) microlasers with an output waveguide connected to one of the vertices of the ETR are suitable to be a light source for photonic integrated circuits. InP-GaInAsP ETR lasers with side length from 10 to 30 pm and the output-waveguide width of 1 or 2 pm are fabricated using standard photolithography and inductively coupled-plasma etching techniques. Continuous-wave electrically injected 1520-nm ETR laser with 20-mu m sides is realized with the maximum output power 0.17 and 0.067 mW and the threshold current 34 and 43 mA at 290 K and 295 K, respectively.

Equilateral-triangle-resonator injection lasers with directional emission

Equilateral-triangle-resonator (ETR) lasers with an output waveguide jointed at one vertex of the resonator are fabricated on (100) GaInAsP-InP wafers using photolithography and a two-step inductively coupled plasma (ICP) etching technique. Distinct peaks with the mode spacing of longitudinal mode intervals are observed in the luminescence spectra at room temperature. Furthermore, some minor peaks appear in the middle of the main peaks, which can be attributed to the first-order transverse modes as predicted in the theoretical results. CW directional lasing emissions are achieved for ETR lasers with side lengths ranging from 15 to 30 pm up to 200 K. The temperature dependences of the threshold current and lasing wavelength are measured for an ETR laser with the side length of 20 mu m from 80 to 200 K. The observed threshold current rapidly increases as temperature increases over 170 K.

Analysis of semiconductor microlasers with an equilateral triangle resonator by rate equations

Semiconductor microlasers with an equilateral triangle resonator (ETR) are analyzed by rate equations with the mode lifetimes calculated by the finite-difference time-domain technique and the Pade approximation. A gain spectrum based on the relation of the gain spectrum and the spontaneous emission spectrum is proposed for considering the mode selection in a wide wavelength span. For an ETR microlaser with the side length of about 5 mum, we find that single fundamental mode operation at about 1.55 mum can be obtained as the side length increases from 4.75 to 5.05 mum. The corresponding wavelength tuning range is 93 nm, and the threshold current is about 0.1 to 0.4 mA.

Analysis and numerical simulation of eigenmode characteristics for semiconductor lasers with an equilateral triangle micro-resonator

The eigenmodes confined in the equilateral triangle resonator (ETR) are analyzed by deriving the eigenvalues and the mode field distributions and by the finite difference time domain (FDTD) technique. The analytical results show that the one-period-length for the mode light rays inside the ETR is the perimeter of the ETR, and the number of transverse modes is limited by the condition of total internal reflection. In addition, the sum of the longitudinal mode index and the transverse mode index should be an even number, which limits the number of confined modes again. Based on the FDTD technique and the Pade approximation, we calculate the mode resonant frequencies and the quality factors from the local maximum and the width of the spectral distribution of the intensity The numerical results of mode frequencies agree very well with the analytical results, and the quality factor of the fundamental mode is usually higher than that of the higher order transverse modes. The results show that the ETR is suitable to realize single-made operation as semiconductor microcavity lasers.

Influence of output waveguide on mode quality factor in semiconductor microlasers with an equilateral triangle resonator

Semiconductor microlasers with an equilateral triangle resonator (ETR) and an output waveguide are proposed and analyzed by the finite-difference time-domain technique and the Pade approximation. The numerical results show that microlasers with an output waveguide still have a high-quality factor (Q factor) and are suitable to realize directional emission. For the ETR with a 0.46-mum-width opening in one of the vertices connected to the output waveguide, we have the Q factor of 1.5x10(3) and 2.5x10(2) for the TM fundamental mode at the wavelength of 1.55 mum, as the side length of the ETR is 5 and 3 mum. The simulated intensity distributions are presented for the fundamental mode in the ETR with a side length of 3 mum and an opening of 0.23 mum. (C) 2000 American Institute of Physics. [S0003-6951(00)01749-6].

Polarization-Independent Micro-Ring Resonator on Silicon-on-Insulator

Polarization-independent laterally-coupled micro-ring resonator has been designed and demonstrated. The origin of the polarization-sensitivity of the photonic wire waveguide (PWW) was analyzed. A polarization-insensitive PWW structure was designed and a polarization-insensitive MRR based on this PWW structure was designed by finite difference time-domain method and was fabricated on an 8-inch silicon-on-insulator wafer. The offset between the resonant wavelengths of the quasi-TE mode and the quasi-TM mode is smaller than 0.15 nm. The FSR is about 17 nm, extinction ratio about 10 dB and Q about 620.

High Q microring resonator in silicon-on-insulator rib waveguides - art. no. 68380J

A high quality (Q) factor microring resonator in silicon-on-insulator rib waveguides was fabricated by electron beam lithography, followed by inductively coupled plasma etching. The waveguide dimensions were scaled down to submicron, for a low bending loss and compactness. Experimentally, the resonator has been realized with a quality factor as high as 21,200, as well as a large extinction ratio 12.5dB at telecommunication wavelength near 1550nm. From the measured results, propagation loss in the rib waveguide is determined as low as 6.900/cm. This high Q microring resonator is expected to lead to high speed optical modulators and bio-sensing devices.

In-situ Boron-doped Low-stress LPCVD Polysilicon for Micromechanical Disk Resonator

Polycrystalline silicon (polysilicon) has been used as an important structural material for microelectro-mechnical systems (MEMS) because of its compatibility with standard integrated circuit (IC) processes. As the structural layer of micromechanical high resonance frequency (high-f) and high quality factor (high-Q) disk resonators, the low residual stress and low resistivity are desired for the polysilicon thin films. In the present work, we investigate the effect of deposition and annealing conditions on the residual stress and resistivity for in-situ deposited low pressure chemical vapor deposition (LPCVD) polysilicon films. Low residual stress (-100 MPa) was achieved in in-situ boron-doped polysilicon films deposited at 570 degrees C and annealed at 1000 degrees C for 4 hr. The as-deposited amorphous polysilicon films were crystallized by the rapid thermal annealing and have the (111)-preferred orientation, the low tensile residual stress is expected for this annealed film, the detailed description on this work will be reported soon. The controllable residual stress and resistivity make these films suitable for high-Q and bigh-f micro-mechanical disk resonators.

Continuous-wave electrically injected InP/GaInAsP equilateral-triangle-resonator lasers

Equilateral-triangle-resonator (ETR) microlasers with an output waveguide connected to one of the vertices of the ETR are fabricated using standard photolithography and inductively-coupled-plasma etching techniques. Continuous-wave electrically injected 1550 nm ETR laser with side length ranged from 15 to 30 tm are realized at room temperature.

Heavily doped polycrystalline 3C-SiC growth on SiO2/Si(100) substrates for resonator applications

3C-SiC is a promising material for the development of microelectromechanical systems (MEMS) applications in harsh environments. This paper presents the LPCVD growth of heavily nitrogen doped polycrystalline 3C-SiC films on Si wafers with 2.0 mu m-thick silicon dioxide (SiO2) films for resonator applications. The growth has been performed via chemical vapor deposition using SiH4 and C2H4 precursor gases with carrier gas of H-2 in a newly developed vertical CVD chamber. NH3 was used as n-type dopant. 3C-SiC films were characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), secondary ion mass spectroscopy (SIMS), and room temperature Hall Effect measurements. It was shown that there is no voids at the interface between 3C-SiC and SiO2. Undoped 3C-SiC films show n-type conduction with resisitivity, Hall mobility, and carrier concentration at room temperature of about 0.56 Omega center dot cm, 54 cm(2)/Vs, and 2.0x 10(17) cm(-3), respectively. The heavily nitrogen doped polycrystalline 3C-SiC with the resisitivity of less than 10(-3) Omega center dot cm was obtained by in-situ doping. Polycrystalline SiC resonators have been fabricated preliminarily on these heavily doped SiC films with thickness of about 2 mu m. Resonant frequency of 49.1 KHz was obtained under atmospheric pressure.