Regrouping unfamiliar animals in the weeks prior to slaughter has few effects on physiology and meat quality in Bos taurus feedlot steers

The response of cattle to alterations in social groupings can lead to physiological changes that affect meat quality. Feedlot practices frequently lead to a proportion of cattle in a pen being drafted for slaughter with the balance retained for a further period until they meet market specifications. An ability to regroup such retained cattle for short periods without consequences for meat quality would facilitate efficient use of feedlot pen space. The current experiment examined the impact on physiological variables and meat quality of regrouped British breed steers 4, 2 or 1 week before dispatch for slaughter. There was little effect of regrouping cattle on physiological variables associated with stress responses. Physical assessment of meat quality indicated that regrouping steers 1 week before slaughter led to higher compression and a tendency for higher peak force values in animals from one genotype than in their respective controls (1.89 v. 1.71 ± 0.05 kg, P = 0.017); however, these assessments were not matched by changes in sensory perception of meat quality. Average daily gain during feedlot finishing was negatively related to the temperament measure and flight time. It was also associated with breed, white cell count, plasma cortisol and haemoglobin at the midpoint of the 70-day finishing period. The results confirm the impact of flight time on growth rate during feedlot finishing and that regrouping cattle less than 2 weeks before slaughter may reduce meat quality.

Using rowers’ perceptions of on-water stroke success to evaluate sculling catch efficiency variables via a boat instrumentation system

Aim An effective catch in sculling is a critical determinant of boat velocity. This study used rowers’ performance-based judgments to compare three measures of catch slip efficiency. Two questions were addressed: (1) would rower-judged Yes strokes be faster than No strokes? and (2) which method of quantifying catch slip best reflected these judgements? Methods Eight single scullers performed two 10-min blocks of sub maximal on-water rowing at 20 strokes per minute. Every 30 s, rowers reported either Yes or No about the quality of their stroke at the catch. Results It was found that Yes strokes identified by rowers had, on average, a moderate effect advantage over No strokes with a standardised effect size of 0.43. In addition, a quicker time to positive acceleration best reflected the change in performance; where the standardised mean difference score of 0.57 for time to positive acceleration was larger than the scores of 0.47 for time to PowerLine force, and 0.35 for time to 30% peak pin force catch slip measures. For all eight rowers, Yes strokes corresponded to time to positive acceleration occurring earlier than No strokes. Conclusion Rower judgements about successful strokes was linked to achieving a quicker time to positive acceleration, and may be of the most value in achieving a higher average boat velocity.

Commercial application of polychaete sand filters for wastewater remediation and broodstock feeds

Summary Prototype sand-worm filtration beds were constructed at two prawn farms and one fish farm to assess and demonstrate their polychaete (marine worm) production and wastewater remediation capacities at semi-commercial scale. Wastewater treatment properties were monitored and worms produced were assessed and either sold for bait or used by the farms’ hatcheries as broodstock (prawn or fish breeder) feed. More than 34 megalitres of prawn- and fish-pond water was beneficially treated in the 116-319-d trial. The design of the polychaete-assisted sand filters (PASFs) constructed at each farm affected their water handling rates, which on average ranged from 315 to 1000 L m-2 d-1 at the three farms. A low profile design incorporating shallow bunded ponds made from polyethylene liner and timber stakes provided the easiest method of construction. This simple design applied at broad scale facilitated the highest quantities of treated water and the greatest worm production. Designs with higher sides increased the head pressure above the sand bed surface, thus increasing the amount of water that could be treated each day. Most water qualities were affected in a similar way to that demonstrated in the previous tank trials: dissolved oxygen, pH, total suspended solids and chlorophyll a levels were all consistently significantly lowered as pond water percolated through the sand bed, and dissolved forms of nitrogen and phosphorus were marginally increased on several occasions. However, unlike the previous smaller-scale tank trials, total nitrogen (TN) and total phosphorus (TP) levels were both significantly lowered by these larger-scale PASFs. The reasons for this are still unclear and require further research. Maximum TN and TP removals detected in the trial were 48.8% and 67.5%, respectively, and average removals (in unfed beds) at the three farms ranged from 20.0 to 27.7% for TN and from 22.8 to 40.8% for TP. Collectively, these results demonstrate the best suspended solids, chlorophyll and macronutrient removal capacities so far reported for any mariculture wastewater treatment methodology to date. Supplemental feeding of PASFs with fish meal was also investigated at one farm as a potential means of increasing their polychaete biomass production. Whilst fed beds produced higher biomass (152 ± 35 g m-2) compared with unfed beds (89 ± 17 g m-2) after 3.7 months of operation, the low number of replicates (2) prevented statistically significant differences from being demonstrated for either growth or survival. At harvest several months later, worm biomass production was estimated to be similar to, or in slight excess of, previously reported production levels (300-400 g m-2). Several qualities of filtered water appear to have been affected by supplemental feeding: it appeared to marginally lower dissolved oxygen and pH levels, and increased the TN and TP levels though not so much to eliminate significant beneficial water treatment effects. Periodic sampling during an artificial-tide demonstrated the tendency for treated-water quality changes during the first hour of filtration. Total nitrogen and ammonia peaked early in the tidal flow and then fell to more stable levels for the remainder of the filtration period. Other dissolved nutrients also showed signs of this sand-bed-flushing pattern, and dissolved oxygen tended to climb during the first hour and become more stable thereafter. These patterns suggest that the routine sampling of treated water undertaken at mid-inflow during the majority of the wider study would likely have overestimated the levels of TN and dissolved nutrients discharged from the beds, and hence underestimated the PASFs treatment efficacies in this regard. Analyses of polychaete biomass collected from each bed in the study revealed that the worms were free from contamination with the main prawn viruses that would create concerns for their feeding to commercial prawn broodstock in Australia. Their documented proximal and nutritional contents also provide a guide for hatchery operators when using live or frozen stock. Their dry matter content ranged from 18.3 to 22.3%, ash ranged from 10.2 to 14.0%, gross energy from 20.2 to 21.5 MJ kg-1, and fat from 5.0 to 9.2%. Their cholesterol levels ranged from 0.86 to 1.03% of dry matter, whilst total phospholipids range from 0.41 to 0.72%. Thirty-one different fatty acids were present at detectable (≥0.005% of dry matter) levels in the sampled worm biomass. Palmitic acid was by far the most prevalent fatty acid detected (1.21 ± 0.18%), followed by eicosapentaenoic (EPA) (0.48 ± 0.03%), stearic (0.46 ± 0.04%), vaccenic (0.38 ± 0.05%), adrenic (0.35 ± 0.02%), docosadienoic (0.28 ± 0.02%), arachidonic (AA) (0.22 ± 0.01%), palmitoleic (0.20 ± 0.04%) and 23 other fatty acids with average contents of less than 0.2% of dry matter. Supplemental feeding with fish meal at one farm appeared to increase the docosahexaenoic acid (DHA) content of the worms considerably, and modify the average AA : EPA : DHA from 1.0 : 2.7 : 0.3 to 1.0 : 2.0 : 1.1. Consistent with previous results, the three most heavily represented amino acids in the dry matter of sampled worms were glutamic acid (8.5 ± 0.2%), aspartic acid (5.5 ± 0.1%) and glycine (4.9 ± 0.5%). These biomass content results suggest that worms produced in PASF systems are well suited to feeding to prawn and fish broodstock, and provide further strong evidence of the potential to modify their contents for specific nutritional uses. The falling wild-fishery production of marine bloodworms in Queensland is typical of diminishing polychaete resources world-wide and demonstrates the need to develop sustainable production methods here and overseas. PASF systems offer the dual benefits of wastewater treatment for environmental management and increased productivity through a valuable secondary crop grown exclusively on waste nutrients.

Role of Native Fish in Integrated Aquatic Weed and Water Quality Management within the Burdekin Irrigation Area

This report summarises work conducted by the QDPI, in partnership with the South Burdekin Water Board (SBWB) and the Burdekin Shire Council (BSC) between 2001 and 2003. The broad aim of the research was to assess the potential of native fish as biocontrol agents for noxious weeds, as part of an integrated program for managing water quality in the Burdekin Irrigation Area. A series of trials were conducted at, or using water derived from, the Sandy Creek Diversion near Groper Creek (lower Burdekin delta). Trials demonstrated that aquatic weeds play a positive role in trapping transient nutrients, until such time that weed growth becomes self-shading and weed dieback occurs, which releases stored nutrients and adversely affects water quality. Transient nutrient levels (av. TN<0.5mg/L; av. TP<0.1mg/L) found in the irrigation channel during the course of this research were substantially lower than expected, especially considering the intensive agriculture and sewage effluent discharge upstream from the study site. This confirms the need to consider the control of weeds rather than complete weed extermination when formulating management plans. However, even when low nutrient levels are available, there is competitive exploitation of habitat variables in the irrigation area leading to succession and eventual domination by certain weed species. During these trials, we have seen filamentous algae, phytoplankton, hyacinth and curled pondweed each hold competitive advantage at certain points. However without intervention, floating weeds, especially hyacinth, ultimately predominate in the Burdekin delta due to their fast propagation rate and their ability to out-shade submerged plants. We have highlighted the complexity of interactions in these highly disturbed ecosystems in that even if the more prevalent noxious weeds are contained, other weed species will exploit the vacant niche. This complexity places stringent requirements on the type of native fish that can be used as biocontrol agents. Of the seven fish species identified with herbivorous trophic niches, most target plankton or algae and do not have the physical capacity to directly eat the larger macrophytes of the delta. We do find however that following mechanical weed harvesting, inoculative releases of fish can slow the rate of hyacinth recolonisation. This occurs by mechanisms in addition to direct weed consumption, such as disturbing growth surfaces by grazing on attached biofilms. Predation by birds and water rats presents another impediment to the efficacy of large-scale releases of fish. However, alternative uses of fish in water quality management in the Burdekin irrigation area are discussed.

Wastewater remediation options for prawn farms - Aquaculture Industry Development Initiative 2002-04.

There are many potential bioremediation approaches that may be suitable for prawn farms in Queensland. Although most share generally accepted bioremediation principles, advocacy for different methods tends to vary widely. This diversity of approach is particularly driven by the availability and knowledge of functional species at different localities around the world. In Australia, little is known about the abilities of many native species in this regard, and translocation and biosecurity issues prevent the use of exotic species that have shown potential in other countries. Species selected must be tolerant of eutrophic conditions and ecological shifts, because prawn pond nutrient levels and pathways can vary with different assemblages of autotrophic and heterotrophic organisms. Generally, they would be included in a constructed ecosystem because of their functional contributions to nutrient cycling and uptake, and to create nutrient sinks in forms of harvestable biomass. Wide salinity, temperature and water quality tolerances are also valuable attributes for selected species due to the sometimes-pronounced effects of environmental extremes, and to provide over-wintering options and adequate safety margins in avoiding mass mortalities. To practically achieve these bioremediation polycultures on a large scale, and in concert with the operations of a prawn farm, methods involving seed production, stock management, and a range of other farm engineering and product handling systems need to be reliably achievable and economically viable. Research funding provided by the Queensland Government through the Aquaculture Industry Development Initiative (AIDI) 2002-04 has enabled a number of technical studies into biological systems to treat prawn farm effluent for recirculation and improved environmental sustainability. AIDI bioremediation research in southern Queensland was based at the Bribie Island Aquaculture Research Centre (BIARC), and was conducted in conjunction with AIDI genetics and selection research, and a Natural Heritage Trust (NHT) funded program (Coast and Clean Seas Project No.717757). This report compilation provides a summary of some of the work conducted within these programs.

Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Effect of water quality and season on the population dynamics of Cabomba caroliniana in subtropical Queensland, Australia

Cabomba caroliniana is a submersed aquatic macrophyte that originates from the Americas and is currently invading temperate, subtropical, and tropical freshwater habitats around the world. Despite being a nuisance in many countries, little is known about its ecology. We monitored C. caroliniana populations in three reservoirs in subtropical Queensland, Australia, over 5.5 years. Although biomass, stem length, and plant density of the C. caroliniana stands fluctuated over time, they did not exhibit clear seasonal patterns. Water depth was the most important environmental factor explaining C. caroliniana abundance. Plant biomass was greatest at depths from 2–4 m and rooted plants were not found beyond 5 m. Plant density was greatest in shallow water and decreased with depth, most likely as a function of decreasing light and increasing physical stress. We tested the effect of a range of water physico-chemical parameters. The concentration of phosphorus in the water column was the variable that explained most of the variation in C. caroliniana population parameters. We found that in subtropical Australia, C. caroliniana abundance does not appear to be affected by seasonal conditions but is influenced by other environmental variables such as water depth and nutrient loading. Therefore, further spread will more likely be governed by local habitat rather than climatic conditions.

Effect of water quality and season on the population dynamics of Cabomba caroliniana in subtropical Queensland, Australia

Cabomba caroliniana is a submersed aquatic macrophyte that originates from the Americas and is currently invading temperate, subtropical, and tropical freshwater habitats around the world. Despite being a nuisance in many countries, little is known about its ecology. We monitored C. caroliniana populations in three reservoirs in subtropical Queensland, Australia, over 5.5 years. Although biomass, stem length, and plant density of the C. caroliniana stands fluctuated over time, they did not exhibit clear seasonal patterns. Water depth was the most important environmental factor explaining C. caroliniana abundance. Plant biomass was greatest at depths from 2–4 m and rooted plants were not found beyond 5 m. Plant density was greatest in shallow water and decreased with depth, most likely as a function of decreasing light and increasing physical stress. We tested the effect of a range of water physico-chemical parameters. The concentration of phosphorus in the water column was the variable that explained most of the variation in C. caroliniana population parameters. We found that in subtropical Australia, C. caroliniana abundance does not appear to be affected by seasonal conditions but is influenced by other environmental variables such as water depth and nutrient loading. Therefore, further spread will more likely be governed by local habitat rather than climatic conditions.

Polybridge Technical Report

This study examined the physical and chemical properties of a novel, fully-recirculated prawn and polychaete production system that incorporated polychaete-assisted sand filters (PASF). The aims were to assess and demonstrate the potential of this system for industrialisation, and to provide optimisations for wastewater treatment by PASF. Two successive seasons were studied at commercially-relevant scales in a prototype system constructed at the Bribie Island Research Centre in Southeast Queensland. The project produced over 5.4 tonnes of high quality black tiger prawns at rates up to 9.9 tonnes per hectare, with feed conversion of up to 1.1. Additionally, the project produced about 930 kg of high value polychaete biomass at rates up to 1.5 kg per square metre of PASF, with the worms feeding predominantly on waste nutrients. Importantly, this closed production system demonstrated rapid growth of healthy prawns at commercially relevant production levels, using methods that appear feasible for application at large scale. Deeper (23 cm) PASF beds provided similar but more reliable wastewater treatment efficacies compared with shallower (13 cm) beds, but did not demonstrate significantly greater polychaete productivity than (easier to harvest) shallow beds. The nutrient dynamics associated with seasonal and tidal operations of the system were studied in detail, providing technical and practical insights into how PASF could be optimised for the mitigation of nutrient discharge. The study also highlighted some of the other important advantages of this integrated system, including low sludge production, no water discharge during the culture phase, high ecosystem health, good prospects for biosecurity controls, and the sustainable production of a fishery-limited resource (polychaetes) that may be essential for the expansion of prawn farming industries throughout the world. Regarding nutrient discharge from this prototype mariculture system, when PASF was operating correctly it proved feasible to have no water (or nutrient) discharge during the entire prawn growing season. However, the final drain harvest and emptying of ponds that is necessary at the end of the prawn farming season released 58.4 kg ha-1 of nitrogen and 6 kg ha-1 of phosphorus (in Season 2). Whilst this is well below (i.e., one-third to one-half of) the current load-based licencing conditions for many prawn farms in Australia, the levels of nitrogen and chlorophyll a in the ponds remained higher than the more-stringent maximum limits at the Bribie Island study site. Zero-net-nutrient discharge was not achieved, but waste nutrients were low where 5.91 kg of nitrogen and 0.61 kg of phosphorus was discharged per tonne of prawns produced. This was from a system that deployed PASF at 14.4% of total ponded farm area which treated an average of 5.8% of pond water daily and did not use settlement ponds or other natural or artificial water remediation systems. Four supplemental appendices complement this research by studying several additional aspects that are central to the industrialisation of PASF. The first details an economic model and decision tool which allows potential users to interactively assess construction and operational variables of PASF at different scales. The second provides the qualitative results of a prawn maturation trial conducted collaboratively with the Commonwealth Scientific and Industrial Research Organisation (CSIRO) to assess dietary inclusions of PASF-produced worms. The third provides the reproductive results from industry-based assessments of prawn broodstock produced using PASF. And the fourth appendix provides detailed elemental and nutritional analyses of bacterial biofilm produced by PASF and assesses its potential to improve the growth of prawns in recirculated culture systems.

An imprecise fuzzy risk approach for water quality management of a river system

Uncertainty plays an important role in water quality management problems. The major sources of uncertainty in a water quality management problem are the random nature of hydrologic variables and imprecision (fuzziness) associated with goals of the dischargers and pollution control agencies (PCA). Many Waste Load Allocation (WLA)problems are solved by considering these two sources of uncertainty. Apart from randomness and fuzziness, missing data in the time series of a hydrologic variable may result in additional uncertainty due to partial ignorance. These uncertainties render the input parameters as imprecise parameters in water quality decision making. In this paper an Imprecise Fuzzy Waste Load Allocation Model (IFWLAM) is developed for water quality management of a river system subject to uncertainty arising from partial ignorance. In a WLA problem, both randomness and imprecision can be addressed simultaneously by fuzzy risk of low water quality. A methodology is developed for the computation of imprecise fuzzy risk of low water quality, when the parameters are characterized by uncertainty due to partial ignorance. A Monte-Carlo simulation is performed to evaluate the imprecise fuzzy risk of low water quality by considering the input variables as imprecise. Fuzzy multiobjective optimization is used to formulate the multiobjective model. The model developed is based on a fuzzy multiobjective optimization problem with max-min as the operator. This usually does not result in a unique solution but gives multiple solutions. Two optimization models are developed to capture all the decision alternatives or multiple solutions. The objective of the two optimization models is to obtain a range of fractional removal levels for the dischargers, such that the resultant fuzzy risk will be within acceptable limits. Specification of a range for fractional removal levels enhances flexibility in decision making. The methodology is demonstrated with a case study of the Tunga-Bhadra river system in India.

Health-Related Quality of Life, Costs and Treatment of Inflammatory Rheumatic Diseases in Routine Practice : With special emphasis on biological drugs

Rheumatoid arthritis (RA) and other chronic inflammatory joint diseases already begin to affect patients health-related quality of life (HRQoL) in the earliest phases of these diseases. In treatment of inflammatory joint diseases, the last two decades have seen new strategies and treatment options introduced. Treatment is started at an earlier phase; combinations of disease-modifying anti-rheumatic drugs (DMARDs) and corticosteroids are used; and in refractory cases new drugs such as tumour necrosis factor (TNF) inhibitors or other biologicals can be started. In patients with new referrals to the Department of Rheumatology of the Helsinki University Central Hospital, we evaluated the 15D and the Stanford Health Assessment Questionnaire (HAQ) results at baseline and approximately 8 months after their first visit. Altogether the analysis included 295 patients with various rheumatic diseases. The mean baseline 15D score (0.822, SD 0.114) was significantly lower than for the age-matched general population (0.903, SD 0.098). Patients with osteoarthritis (OA) and spondyloarthropathies (SPA) reported the poorest HRQoL. In patients with RA and reactive arthritis (ReA) the HRQoL improved in a statistically significant manner during the 8-month follow-up. In addition, a clinically important change appeared in patients with systemic rheumatic diseases. HAQ score improved significantly in patients with RA, arthralgia and fibromyalgia, and ReA. In a study of 97 RA patients treated either with etanercept or adalimumab, we assessed their HRQoL with the RAND 36-Item Health Survey 1.0 (RAND-36) questionnaire. We also analysed changes in clinical parameters and the HAQ. With etanercept and adalimumab, the values of all domains in the RAND-36 questionnaire increased during the first 3 months. The efficacy of each in improving HRQoL was statistically significant, and the drug effects were comparable. Compared to Finnish age- and sex-matched general population values, the HRQoL of the RA patients was significantly lower at baseline and, despite the improvement, remained lower also at follow-up. Our RA patients had long-standing and severe disease that can explain the low HRQoL also at follow-up. In a pharmacoeconomic study of patients treated with infliximab we evaluated medical and work disability costs for patients with chronic inflammatory joint disease during one year before and one year after institution of infliximab treatment. Clinical and economic data for 96 patients with different arthritis diagnoses showed, in all patients, significantly improved clinical and laboratory variables. However, the medical costs increased significantly during the second period by 12 015 (95% confidence interval, 6 496 to 18 076). Only a minimal decrease in work disability costs occurred mean decrease 130 (-1 268 to 1 072). In a study involving a switch from infliximab to etanercept, we investigated the clinical outcome in 49 patients with RA. Reasons for switching were in 42% failure to respond by American College of Rheumatology (ACR) 50% criteria; in 12% adverse event; and in 46% non-medical reasons although the patients had responded to infliximab. The Disease Activity Score with 28 joints examined (DAS28) allowed us to measure patients disease activity and compare outcome between groups based on the reason for switching. In the patients in whom infliximab was switched to etanercept for nonmedical reasons, etanercept continued to suppress disease activity effectively, and 1-year drug survival for etanercept was 77% (95% CI, 62 to 97). In patients in the infliximab failure and adverse event groups, DAS28 values improved significantly during etanercept therapy. However, the 1-year drug survival of etanercept was only 43% (95% CI, 26 to 70) and 50% (95% CI, 33 to 100), respectively. Although the HRQoL of patients with inflammatory joint diseases is significantly lower than that of the general population, use of early and aggressive treatment strategies including TNF-inhibitors can improve patients HRQoL effectively. Further research is needed in finding new treatment strategies for those patients who fail to respond or lose their response to TNF-inhibitors.

Dynamic simulation of activated sludge based wastewater treatment processes: Case studies with Titagarh Sewage Treatment Plant, India

STOAT has been extensively used for the dynamic simulation of an activated sludge based wastewater treatment plant in the Titagarh Sewage Treatment Plant, near Kolkata, India. Some alternative schemes were suggested. Different schemes were compared for the removal of Total Suspended Solids (TSS), b-COD, ammonia, nitrates etc. A combination of IAWQ#1 module with the Takacs module gave best results for the existing scenarios of the Titagarh Sewage Treatment Plant. The modified Bardenpho process was found most effective for reducing the mean b-COD level to as low as 31.4 mg/l, while the mean TSS level was as high as 100.98 mg/l as compared to the mean levels of TSS (92 62 mg/l) and b-COD (92.0 mg/l) in the existing plant. Scheme 2 gave a better scenario for the mean TSS level bringing it down to a mean value of 0.4 mg/l, but a higher mean value for the b-COD level at 54.89 mg/l. The Scheme Final could reduce the mean TSS level to 2.9 mg/l and the mean b-COD level to as low as 38.8 mg/l. The Final Scheme looks to be a technically viable scheme with respect to the overall effluent quality for the plant. (C) 2009 Elsevier B.V. All rights reserved.

Turbulent vertical fluxes and air quality measured in urban air in Helsinki

There is a growing need to understand the exchange processes of momentum, heat and mass between an urban surface and the atmosphere as they affect our quality of life. Understanding the source/sink strengths as well as the mixing mechanisms of air pollutants is particularly important due to their effects on human health and climate. This work aims to improve our understanding of these surface-atmosphere interactions based on the analysis of measurements carried out in Helsinki, Finland. The vertical exchange of momentum, heat, carbon dioxide (CO2) and aerosol particle number was measured with the eddy covariance technique at the urban measurement station SMEAR III, where the concentrations of ultrafine, accumulation mode and coarse particle numbers, nitrogen oxides (NOx), carbon monoxide (CO), ozone (O3) and sulphur dioxide (SO2) were also measured. These measurements were carried out over varying measurement periods between 2004 and 2008. In addition, black carbon mass concentration was measured at the Helsinki Metropolitan Area Council site during three campaigns in 1996-2005. Thus, the analyzed dataset covered far, the most comprehensive long-term measurements of turbulent fluxes reported in the literature from urban areas. Moreover, simultaneously measured urban air pollution concentrations and turbulent fluxes were examined for the first time. The complex measurement surrounding enabled us to study the effect of different urban covers on the exchange processes from a single point of measurement. The sensible and latent heat fluxes closely followed the intensity of solar radiation, and the sensible heat flux always exceeded the latent heat flux due to anthropogenic heat emissions and the conversion of solar radiation to direct heat in urban structures. This urban heat island effect was most evident during winter nights. The effect of land use cover was seen as increased sensible heat fluxes in more built-up areas than in areas with high vegetation cover. Both aerosol particle and CO2 exchanges were largely affected by road traffic, and the highest diurnal fluxes reached 109 m-2 s-1 and 20 µmol m-2 s-1, respectively, in the direction of the road. Local road traffic had the greatest effect on ultrafine particle concentrations, whereas meteorological variables were more important for accumulation mode and coarse particle concentrations. The measurement surroundings of the SMEAR III station served as a source for both particles and CO2, except in summer, when the vegetation uptake of CO2 exceeded the anthropogenic sources in the vegetation sector in daytime, and we observed a downward median flux of 8 µmol m-2 s-1. This work improved our understanding of the interactions between an urban surface and the atmosphere in a city located at high latitudes in a semi-continental climate. The results can be utilised in urban planning, as the fraction of vegetation cover and vehicular activity were found to be the major environmental drivers affecting most of the exchange processes. However, in order to understand these exchange and mixing processes on a city scale, more measurements above various urban surfaces accompanied by numerical modelling are required.

Sedimentary zooplankton remains as indicators of lake ecological quality and trophic structure

To protect and restore lake ecosystems under threats posed by the increasing human population, information on their ecological quality is needed. Lake sediments provide a data rich archive that allows identification of various biological components present prior to anthropogenic alterations as well as a constant record of changes. By providing a longer dimension of time than any ongoing monitoring programme, palaeolimnological methods can help in understanding natural variability and long-term ecological changes in lakes. As zooplankton have a central role in the lake food web, their remains can potentially provide versatile information on past trophic structure. However, various taphonomic processes operating in the lakes still raise questions concerning how subfossil assemblages reflect living communities. This thesis work aimed at improving the use of sedimentary zooplankton remains in the reconstruction of past zooplankton communities and the trophic structure in lakes. To quantify interspecific differences in the accumulation of remains, the subfossils of nine pelagic zooplankton taxa in annually laminated sediments were compared with monitoring results for live zooplankton in Lake Vesijärvi. This lake has a known history of eutrophication and recovery, which resulted from reduced external loading and effective fishing of plankti-benthivorous fish. The response of zooplankton assemblages to these known changes was resolved using annually laminated sediments. The generality of the responses observed in Lake Vesijärvi were further tested with a set of 31 lakes in Southern Finland, relating subfossils in surface sediments to contemporary water quality and fish density, as well as to lake morphometry. The results demonstrated differential preservation and retention of cladoceran species in the sediment. Daphnia, Diaphanosoma and Ceriodaphnia were clearly underrepresented in the sediment samples in comparison to well-preserved Bosmina species, Chydorus, Limnosida and Leptodora. For well-preserved species, the annual net accumulation rate was similar to or above the expected values, reflecting effective sediment focusing and accumulation in the deepest part of the lake. The decreased fish density and improved water quality led to subtle changes in zooplankton community composition. The abundance of Diaphanosoma and Limnosida increased after the reduction in fish density, while Ceriodaphnia and rotifers decreased. The most sensitive indicator of fish density was the mean size of Daphnia ephippia and Bosmina (E.) crassicornis ephippia and carapaces. The concentration of plant-associated species increased, reflecting expanding littoral vegetation along with increasing transparency. Several of the patterns observed in Lake Vesijärvi could also be found within the set of 31 lakes. According to this thesis work, the most useful cladoceran-based indices for nutrient status and planktivorous fish density in Finnish lakes were the relative abundances of certain pelagic taxa, and the mean size of Bosmina spp. carapaces, especially those of Bosmina (E.) cf. coregoni. The abundance of plant-associated species reflected the potential area for aquatic plants. Lake morphometry and sediment organic content, however, explained a relatively high proportion of the variance in the species data, and more studies are needed to quantify lake-specific differences in the accumulation and preservation of remains. Commonly occurring multicollinearity between environmental variables obstructs the cladoceran-based reconstruction of single environmental variables. As taphonomic factors and several direct and indirect structuring forces in lake ecosystems simultaneously affect zooplankton, the subfossil assemblages should be studied in a holistic way before making final conclusions about the trophic structure and the change in lake ecological quality.

Interest in university studies : Its role and relation to other motivational variables

This dissertation empirically explored interest as a motivational force in university studies, including the role it currently plays and possible ways of enhancing this role as a student motivator. The general research questions were as follows: 1) What role does interest play in university studies? 2) What explains academic success if studying is not based on interest? 3) How do different learning environments support or impede interest-based studying? Four empirical studies addressed these questions. Study 1 (n=536) compared first-year students explanations of their disciplinary choices in three fields: veterinary medicine, humanities and law. Study 2 (n=28) focused on the role of individual interest in the humanities and veterinary medicine, fields which are very different from each other as regards their nature of studying. Study 3 (n=52) explored veterinary students motivation and study practices in relation to their study success. Study 4 (n=16) explored veterinary students interest experience in individual lectures on a daily basis. By comparing different fields and focusing on one study field in more detail, it was possible to obtain a many-sided picture of the role of interest in different learning environments. Questionnaires and quantitative methods have often been used to measure interest in academic learning. The present work is based mostly on qualitative data, and qualitative methods were applied to add to the previous research. Study 1 explored students open-ended answers, and these provided a basis for the interviews in Study 2. Study 3 explored veterinary students portfolios in a longitudinal setting. For Study 4, a diary including both qualitative and quantitative measures was designed to capture veterinary students interest experience. Qualitative content analysis was applied in all four studies, but quantitative analyses were also added. The thesis showed that university students often explain their disciplinary choices in terms of interest. Because interest is related to high-quality learning, the students seemed to have a good foundation for successful studies. However, the learning environments did not always support interest-based studying; Time-management and coping skills were found to be more important than interest in terms of study success. The results also indicated that interest is not the only motivational variable behind university studies. For example, future goals are needed in order to complete a degree. Even so, the results clearly indicated that it would be worth supporting interest-based studying both in professionally and generally oriented study fields. This support is important not only to promote high-quality learning but also meaningful studying, student well-being, and life-long learning.