高真空室中的水蒸气对HfO2薄膜性能的影响

本文研究了在镀膜过程中真空室内水蒸气的含量对HfO2薄膜物理性能的影响。用电子束蒸发和光电极值监控的方法在BK7基底上制备HfO2薄膜。利用残余气体分析仪在线监测了真空室内的残余气氛组成。分别用Lambda 900光谱仪、X射线衍射方法、表面热透镜技术和1064nm的激光器测试了薄膜的光学性能、微结构、吸收和激光损伤阈值。实验发现，附加冷阱装置有助于我们有效控制镀膜过程中的水汽含量，且在水蒸气含量较少的真空室内镀制的薄膜具有较高的折射率，较小的晶粒尺寸，较低的弱吸收值和较高的损伤阈值。

真空中有机污染物对TiO2/SiO2介质膜损伤阈值的影响

本文主要研究了真空中有机污染物对薄膜阈值的影响。采用电子枪蒸镀的方式制备了由TiO2/SiO2两种材料组合而成的1064nm高反膜，分别在大气和真空中对其损伤阈值进行了测量。发现在真空中污染物易黏附于光学元件表面，导致损伤；真空中的氧分子会加速损伤过程，根据破斑形貌的分析认为是由于在激光作用下氧分子与有机污染物发生反应造成的；真空中的有机污染物被去除后，真空和大气中的损伤阈值差别不大，破斑形貌相似。结果表明有机污染物是真空中损伤阈值降低的主要原因。

用于掺钛蓝宝石激光系统的高反膜的激光损伤

用电子束蒸发制备了用于掺钛蓝宝石啁啾脉冲放大激光系统的TiO2/HfO2/SiO2高反膜，其带宽约为176nm（R>98%, λ0=800nm），激光损伤阈值（LIDT）为2.4 J/cm2。通过TiO2和HfO2单层膜的透过光谱计算了这两种材料的折射率和消光系数。高反膜的性能主要由高折射率材料决定：折射率越高，反射带越宽；消光系数越小，薄膜吸收越小，LIDT越高。最后，讨论了高反膜的激光损伤机制。

Ta2O5膜在532, 800 和 1064 nm波长的n-on-1体系下的激光损伤阈值研究

Ta2O5膜采用传统的电子束蒸发方法制备，并在氧气中673 K的条件下进行了退火12 h处理。首先在1-on-1体系下对Ta2O5膜进行了532和1064 nm波长下的激光损伤阈值（LIDT） 研究，然后在n-on-1体系下分别对532，800和1064 nm三种波长下的激光损伤阈值进行了研究。结果表明在n-on-1体系下Ta2O5膜在532和1064 nm波长下的阈值均高于1-on-1体系下的阈值。此外，在n-on-1体系下，薄膜的阈值随波长增加而增大。同时发现，在氧气中进行退火对Ta2O5膜的光学性能

Comparison of TiO2 and ZrO2 films deposited by electron-beam evaporation and by sol-gel process

TiO2 and ZrO2 films are deposited by electron-beam (EB) evaporation and by sol-gel process. The film properties are characterized by visible and Fourier-transform infrared spectrometry, x-ray diffraction analysis, surface roughness measure, absorption and laser-induced damage threshold (LIDT) test. It is found that the sol-gel Elms have lower refractive index, packing density and roughness than EB deposited films due to their amorphous structure and high OH group concentration in the film. The high LIDT of sol-gel films is mainly due to their amorphous and porous structure, and low absorption. LIDT of EB deposited film is considerably affected by defects in the Elm, and LIDT of sol-gel deposited film is mainly effected by residual organic impurities and solvent trapped in the film.

Characteristics of high reflection mirror with an SiO2 top layer for multilayer dielectric grating

The high reflection (HR) mirror composed of dielectric stacks with excellent spectrum characteristics and high damage resistant ability is critical for fabricating multilayer dielectric (MLD) grating for pulse compressor. The selection of the SiO2 material as the top layer of the HR mirror for grating fabrication is beneficial for improving the laser-induced damage threshold of MLD grating as well as minimizing the standing-wave effect in the photoresist during the exposure process. Based on an (HLL) H-9 design comprising quarter-waves of HfO2 ( H) and half-waves of SiO2 ( L), we obtain an optimal design of the HR mirror for MLD grating, the SiO2 top layer of which is optimized with a merit function including both the diffraction efficiency of the MLD grating and the electric field enhancement in the grating. Dependence of the performance of the MLD grating on the fabrication error of the dielectric mirror is analysed in detail. The HR mirror is also fabricated by E-beam evaporation, which shows good spectral characteristics at the exposure wavelength of 413 nm and at the operation wavelength of 1053 nm and an average damage threshold of 10 J cm(-2) for a 12 ns pulse.

Influence of substrate temperature on properties of MgF2 coatings

Thermal boat evaporation was employed to prepare MgF2 single-layer coatings upon both JGS1 and UBK7 substrates at different substrate temperatures. Microstructure, transmittance and residual stress of these coatings were measured by X-ray diffraction, spectrophotometer, and optical interferometer, respectively. Measurement of laser induced damage threshold (LIDT) of the samples was performed at 355 nm, 8 ns pulses. The results showed that high substrate temperature was beneficial to crystallization of the film. Above 244 degrees C, the refractive index increased gradually with the substrate temperature rising. Whereas, it was exceptional at 210 degrees C that the refractive index was higher than those deposited at 244 and 277 degrees C. The tensile residual stresses were exhibited in all MgF2 films, but not well correlated with the substrate temperature. In addition, the stresses were comparatively smaller upon JGS1 substrates. A tendency could be seen that the LIDTs reached the highest values at about 244 degrees C, and the films upon JGS1 had higher LIDTs than those upon UBK7 substrates at the same temperature. Meanwhile, the damage morphologies showed that the laser damage of the coating resulted from an absorbing center at the film-substrate interface. The features of the damages were displayed by an absorbing center dominated model. Furthermore, the reason of the difference in LIDT values was discussed in detail. (C) 2007 Elsevier B.V. All rights reserved.

三倍频分光膜在1064 nm的破斑特性研究

采用电子束蒸发方式制备了两种不同材料组合的分光膜,分别对其在波长1064 nm激光辐照下的损伤阈值进行了测试,用Alpha-Step 500台阶仪对破斑进行了深度测量。实验结果表明,破斑呈现出表面层的剥落和深坑破坏两种形态。表面层的剥落深度在一定范围内不随能量密度的变化而变化；深坑破坏深浅不一,是膜内缺陷融化、汽化及喷发的综合作用的结果,是损伤阈值降低的主要原因。

两种后处理方法对HfO2薄膜性能的影响

利用电子束蒸发和光电极值监控技术制备了氧化铪薄膜，并分别用两种后处理方法（空气中退火和氧等离子体轰击）对样品进行了处理．然后，对样品的透过率、吸收和抗激光损伤阈值进行了测试分析．实验结果表明，两种后处理方法都能不同程度地降低了氧化铪薄膜的吸收损耗、提高了抗激光损伤阈值．实验结果还表明，氧等离子体轰击的后处理效果明显优于热退火，样品的吸收平均值在氧等离子体后处理前后分别为34．8ppm和9．0ppm，而基频（1 064nm）激光损伤阈值分别为10．0J／cm^2和21．4J／cm^2．

氧离子束辅助沉积氧化铪薄膜的激光损伤阈值研究

电子枪蒸发制备了氧化铪薄膜,对氧离子束辅助和未辅助两种情况下的样品进行了折射率、吸收、激光损伤阈值等属性的测试,结果表明,氧离子束辅助沉积的样品与未辅助沉积的样品相比具有高的折射率和高的吸收,以及稍低的激光损伤阈值.经过分析发现,薄膜的激光损伤阈值是影响薄膜抗激光特性的不利因素和有利因素竞争的结果,离子束辅助沉积技术在引入结构致密等有利因素的同时,也引入了吸收增加等不利因素.

全内反射式衍射光栅近场光学特性

利用傅里叶模式理论分析了具有高衍射效率的全内反射式衍射光栅在TE和TM偏振态下的近场光分布特点，讨论了光栅结构参数以及入射角度对光栅内电场增强的影响。结果表明：全内反射光栅内部电场分布对偏振态较敏感，光栅槽深和占宽比对电场增强影响较小，光栅内的峰值电场随光栅周期增大而增大，并且峰值电场随着入射角度的增大而减小。在应用于高功率激光时，降低光栅内部的电场增强可以有效降低损伤风险。

沉积温度对LaF3薄膜性能的影响

abstract {LaF₃ single-layer coatings were prepared by thermal boat evaporation at the deposition temperatures of 189, 255, 277 and 321°C respectively. The crystal structures of the coatings were characterized by X-ray diffraction (XRD). A spectrophotometer was employed to measure its transmittance. Moreover, refractive index, extinction coefficient and cut-off wavelength were obtained from the measured transmittance spectral curve. The residual stress was evaluated by the Stoney's equation and optical interferometer. Laser induce damage threshold (LIDT) was performed by a tripled Nd:YAG laser system. The results show that the crystallization status becomes better with the deposition temperature increasing. Correspondingly, the grain size also gets larger. Meanwhile, the coatings become more compact and the refractive index increases. However, the absorption of coatings seriously rises and the cut-off wavelength drifts to the long wave. In addition, the residual stress also increases and the intrinsic stress plays a determinant role in the coating. The LIDT of the coating also enhances at high temperature.}

离子束辅助反应制备的氧化铪薄膜特性

采用电子束直接蒸发氧化铪、无辅助电子束反应蒸发和离子束辅助反应蒸发金属铪3种沉积方式制备了单层HfO2薄膜,对样品的光学性能、结构特性以及激光损伤特性进行了研究。实验结果表明:通过反应沉积的方法可以有效减少缺陷产生并改善均匀性,施加离子辅助可以提高薄膜的折射率,在一定条件下还可以有效地降低吸收,但激光损伤阈值仍未达到直接采用氧化铪制备的水平;晶体结构方面,离子辅助条件下可以获得单斜相氧化铪薄膜,并且随着轰击能量的提高由(002)面的择优取向向(-111)面转变。

多层介质膜脉冲宽度压缩光栅与超短脉冲作用时的性能分析

基于啁啾脉冲放大技术的超短脉冲激光系统是提供超快、超强激光的重要途径，具有良好输出波形和高损伤阈值的多层介质膜脉冲宽度压缩光栅是获得高峰值功率脉冲激光的关键。基于傅里叶谱变换方法和严格模式理论，分析了多层介质膜光栅（MDG）在超短脉冲作用下的光学特性。结果表明，当MDG的反射带宽小于具有高斯分布的入射脉冲的频谱宽度时，-1级反射脉冲呈非对称高斯分布，其前沿出现振荡，并且-1级反射脉冲能量开始剧烈下降，讨论了MDG结构参数对其反射带宽的影响。分析了MDG与超短脉冲作用时的近场光分布，对提高其抗激光损伤特性具

真空室内金属杂质污染对光学薄膜性能的影响

真空室内金属粒子污染是降低激光薄膜性能的一个重要因素。采用高真空残余气体分析仪,对薄膜沉积过程中的气氛进行分析。发现由黄铜制作的加热灯架在工作时会分解出Zn,在这种条件下沉积薄膜,会使薄膜中掺入金属杂质,导致薄膜激光破坏阈值降低。采用表面分析技术对薄膜的组分进行分析,证实薄膜中锌杂质的存在。激光破坏实验证明,含有锌杂质的薄膜的破坏阈值明显降低。