CO2-laserin soveltaminen WFU-paperin reunan leikkaamiseen

Tämän diplomityön tarkoitus oli selvittää CO2-laserin soveltuvuutta paperin reunan leikkaamiseen ennen liimapuristinta nopealle modernilleWFU-paperikoneelle. Merkittävimmät leikkauskokeet tehtiin leikkaamalla paperirataa todenmukaisissa olosuhteissa koekoneella. Koeleikkauksissa tutkittiin myös päällystettyjen paperilajien CO2-laserleikkausta. Paperin reunan koeleikkauksia suoritettiin leikkauspöytää vasten sekä telaa vasten. Leikkauspöytänä käytettiin korkeapainevesileikkaimelle suunniteltua leikkauspöytää, jota paranneltiin tämän työn yhteydessä paremmin laserleikkaukselle sopivaksi. Telaa vasten suoritetuilla leikkauksilla lasertehon tarve oli suurempi verrattuna pöytää vasten leikkaukseen samalla leikkausnopeudella ja samalla paperilajilla. Laserlaitteiston mitoittaminen oikein pelkkien arkkileikkauskokeiden perusteella ei ollut mahdollista. Myös rullilla tapahtuvia leikkauskokeita tarvittiin. Pöytää vasten tapahtuvaan leikkaamiseen tarvitaan 1000 W laserlaite paperin molemmille reunoille. Tämän tehoiset laserlaitteet riittävät kaikille Changshun PK 1:n paperilajeille niiden lajikohtaiseen maksimiajonopeuteen. Testatuista kolmesta polttovälistä antoi 5" polttoväli parhaat leikkaustulokset. Polttopisteen paikka voi vaihdella ± 0.75 mm paperin pinnasta vaikuttamatta silti merkittävästi lasertehon tarpeeseen. Laserleikatun paperin reuna oli hyvälaatuinen, eikä laserleikkaus aiheuttanut paperille epätoivottuja asioita kuten mustumista.

Fiber Laser Cutting of Mild Steel

Fiber laser for materials processing have undergone a rapid development in the pastseveral years. As fiber laser provides a combination of high beam quality and awavelength that is easily absorbed by metal surfaces, the named future laser isexpected to challenge the CO2 and Nd:YAG lasers in the area of metal cutting. This thesis studied the performance of fiber laser cutting mild steel. In the literature review part, it introduced the laser cutting principle and the principle of fiber laser including the newest development of fiber laser cuttingtechnology. Because the fiber laser cutting mild steel is a very young technology, a preliminary test was made in order to investigate effect of the cutting parameters on cut quality. Then the formal fiber laser cutting experiment was madeby using 3 mm thickness S355 steel with oxygen as assistant gas. The experimentwas focused on the cut quality with maximum cutting speed and minimum oxygen gas pressure. And the cut quality is mainly decided by the kerf width, perpendicularity tolerance, surface roughness and striation patterns. After analysis the cutting result, several conclusions were made. Although the best result got in the experiment is not perfect as predicted, the whole result of the test can be accepted. Compared with CO2 laser, a higher cutting speed was achieved by fiber laser with very low oxygen gas pressure. A further improvement about the cutting quality might be possible by proper selection of process parameters. And in order to investigate the cutting performance more clearly, a future study about cutting different thickness mild steel and different shape was recommended.

Cutting edge: alum adjuvant stimulates inflammatory dendritic cells through activation of the NALP3 inflammasome.

Adjuvants are vaccine additives that stimulate the immune system without having any specific antigenic effect of itself. In this study we show that alum adjuvant induces the release of IL-1beta from macrophages and dendritic cells and that this is abrogated in cells lacking various NALP3 inflammasome components. The NALP3 inflammasome is also required in vivo for the innate immune response to OVA in alum. The early production of IL-1beta and the influx of inflammatory cells into the peritoneal cavity is strongly reduced in NALP3-deficient mice. The activation of adaptive cellular immunity to OVA-alum is initiated by monocytic dendritic cell precursors that induce the expansion of Ag-specific T cells in a NALP3-dependent way. We propose that, in addition to TLR stimulators, agonists of the NALP3 inflammasome should also be considered as vaccine adjuvants.

Optimizing nozzle flow in laser cutting

The purpose of this study was to investigate different laser cutting nozzles, nozzle flows and possibilities to improve nozzle flow. Another goal was to design new nozzle configuration in which laser cutting would succeed with better cutting speed and smaller gas consumption. Nozzles and nozzle flows were studied with various methods. Computational fluid dynamics was used to calculate old, convergent nozzles and new convergent-divergent nozzles. Measurement apparatus was used to measure both nozzle types. In cutting tests different materials were cut with new nozzles. With the use of design convergent-divergent nozzles 25 % better cutting speed and 33 % smaller gas consumption were achieved when cutting quality was good. Computational fluid dynamics was also discovered to be useful aid in nozzle design.

Qualitative, quantitative and temporal study of cutting agents for cocaine and heroin over 9 years

Forensic laboratories mainly focus on the qualification and the quantitation of the illicit drug under analysis as both aspects are used for judiciary purposes. Therefore, information related to cutting agents (adulterants and diluents) detected in illicit drugs is limited in the forensic literature. This article discusses the type and frequency of adulterants and diluents detected in more than 6000 cocaine specimens and 3000 heroin specimens, confiscated in western Switzerland from 2006 to 2014. The results show a homogeneous and quite unchanging adulteration for heroin, while for cocaine it could be characterised as heterogeneous and relatively dynamic. Furthermore, the results indicate that dilution affects more cocaine than heroin. Therefore, the results provided by this study tend to reveal differences between the respective structures of production or distribution of cocaine and heroin. This research seeks to promote the systematic analysis of cutting agents by forensic laboratories. Collecting and processing data related to the presence of cutting agents in illicit drug specimens produces relevant information to understand and to compare the structure of illicit drug markets.

The cutting of cocaine and heroin: a critical review

The illicit drug cutting represents a complex problem that requires the sharing of knowledge from addiction studies, toxicology, criminology and criminalistics. Therefore, cutting is not well known by the forensic community. Thus, this review aims at deciphering the different aspects of cutting, by gathering information mainly from criminology and criminalistics. It tackles essentially specificities of cocaine and heroin cutting. The article presents the detected cutting agents (adulterants and diluents), their evolution in time and space and the analytical methodology implemented by forensic laboratories. Furthermore, it discusses when, in the history of the illicit drug, cutting may take place. Moreover, researches studying how much cutting occurs in the country of destination are analysed. Lastly, the reasons for cutting are addressed. According to the literature, adulterants are added during production of the illicit drug or at a relatively high level of its distribution chain (e.g. before the product arrives in the country of destination or just after its importation in the latter). Their addition seems hardly justified by the only desire to increase profits or to harm consumers' health. Instead, adulteration would be performed to enhance or to mimic the illicit drug effects or to facilitate administration of the drug. Nowadays, caffeine, diltiazem, hydroxyzine, levamisole, lidocaïne and phenacetin are frequently detected in cocaine specimens, while paracetamol and caffeine are almost exclusively identified in heroin specimens. This may reveal differences in the respective structures of production and/or distribution of cocaine and heroin. As the relevant information about cutting is spread across different scientific fields, a close collaboration should be set up to collect essential and unified data to improve knowledge and provide information for monitoring, control and harm reduction purposes. More research, on several areas of investigation, should be carried out to gather relevant information.

Isolation of compounds attractive to the leaf-cutting ant Atta sexdens rubropilosa forel (hymenoptera: Formicidae) from Mabea fistulifera elaiosome

Mabea fistulifera (Euphorbiaceae)is a pioneer plant species with seeds dispersed by the ant Atta sexdens rubropilosa. Since the ants are attracted to the seeds to use its elaiosome as a source of energy, we investigated its composition. The elaiosomes from 13,000 seeds were extracted with a methanol:chloroform mixture (2:1 v/v) and yielded 22% of a residue. This residue was fractionated by column chromatography and its composition determined by infrared spectroscopy and chromatography/mass spectrometry (GC-MS). The elaiosome lipids are constituted mainly by free fatty acids, triacylglycerols and minor quantities of monoacylglycerols or diacylglycerols.

Supply chain costs of a small board lot: sheet cutting and logistics

Succeeding in small board lot (0-20 tons) deliveries, is not always prosperous and failures as well as extra costs compared to standard costs arise. Failure deliveries from converting plants to customer locations tie a lot of unwanted and unexpected costs. Extra costs are handled as quality costs and more precise, internal failure costs. These costs revolve from unsuccessful truck payloads, redundant warehousing or unfavorable routing as examples. Quality costs are becoming more and more important factor in company’s financial decision making. Actual, realized truck payload correlates with the extra costs occurring, so filling the truck payload all get-out well is a key to lower the extra costs. Case company in this study is Corporation A, business segment Boards. Boards have outsourced half of their converting in order to gain better customer service via flexibility, lead time reductions and logistics efficiency improvements. Examination period of the study is first two quarters of year 2008 and deliveries examined are from converters to the customer locations. In Corporation A’s case, the total loss in failure deliveries is hundreds of thousands of Euros during the examination period. So, the logistics goal of getting the right product to the right place and right time for the least cost, does not completely realize.

Investigation of Oxygen Cutting Process in Solid-State Welding

The oxygen cutting is a thermal cutting process, in which metal is heated locally up to its ignition temperature and burnt off by oxygen blast. Oxygen cutting can be used to remove upset metal of a hollow bar occurred due to solid-state welding process. The main goal of this research was to establish a connection between oxygen blasts and mass of metal removed and relate findings to production to suggest improvements to the current process. This master´s thesis describes the designing and building of a test rig for oxygen blowing measurements. It also contains all executed tests and test results, which were carried out. There are different cutting parameters which were studied as well as their effect on cutting process. The oxygen cutting process, used in solid-state welding process, can be improved by the test results.

Tree structure and richness in an Atlantic Forest fragment: distance from anthropogenic and natural edges

Approximately 7.2% of the Atlantic rainforest remains in Brazil, with only 16% of this forest remaining in the State of Rio de Janeiro, all of it distributed in fragments. This forest fragmentation can produce biotic and abiotic differences between edges and the fragment interior. In this study, we compared the structure and richness of tree communities in three habitats - an anthropogenic edge (AE), a natural edge (NE) and the fragment interior (FI) - of a fragment of Atlantic forest in the State of Rio de Janeiro, Brazil (22°50'S and 42°28'W). One thousand and seventy-six trees with a diameter at breast height > 4.8 cm, belonging to 132 morphospecies and 39 families, were sampled in a total study area of 0.75 ha. NE had the greatest basal area and the trees in this habitat had the greatest diameter:height allometric coefficient, whereas AE had a lower richness and greater variation in the height of the first tree branch. Tree density, diameter, height and the proportion of standing dead trees did not differ among the habitats. There was marked heterogeneity among replicates within each habitat. These results indicate that the forest interior and the fragment edges (natural or anthropogenic) do not differ markedly considering the studied parameters. Other factors, such as the age from the edge, type of matrix and proximity of gaps, may play a more important role in plant community structure than the proximity from edges.

Propagation through cutting technique of species ocurring in the Lower São Francisco River in Sergipe State with different concentrations of indolbutiric acid

The objective of this work was to evaluate the feasibility of vegetative propagation through cutting technique of seven tree species with strong occurrence in the riparian forest of the Lower São Francisco River in Sergipe State, under different concentrations of indolbutiric acid at 0, 2500, and 5000 mg.L-1, for potentialization of its use in soil bioengineering technique. It was used a complete random block design with three replicates, and a total of twenty-one treatments. The evaluation period was 120 days for each species, and the data collection was made in intervals of fifteen days, in a total of eight evaluations for each species. The evaluated parameters were: Survival Rate, callus formation, and Root Dry matter Weight. Among the studied species, Schinus terebinthifolius Raddi presented the best results related to cutting technique mainly under the indolbutiric acid concentration of 2500 mg.L-1.