Magnetic properties and oxide petrography of ODP Hole 111-504B

Magnetic properties measurements were performed on 47 samples drilled during Leg 111 of the Ocean Drilling Program and oxide petrography was studied in 32 samples taken at depths throughout the sheeted dike complex in Hole 504B. Integration of these data with results from previous DSDP legs shows that while natural remanent magnetization is constant with depth, magnetic susceptibility increases and median demagnetizing field and the Q ratio decrease with depth in the section. These trends appear to be a result of an increase in deuteric oxidation and a decrease in hydrothermal alteration of primary titanomagnetite with depth. A distinct change in stable magnetic inclination occurs between the extrusive basalts and the sheeted dikes and may be a result of tectonic rotation of the upper extrusive basalts.

Seismic properties of sheeted dikes from ODP Hole 111-504B

Seismic velocities have been measured at confining pressures to 600 MPa for eight samples of sheeted dike rock obtained from Hole 504B during Leg ODP 111. The compressional- and shear-wave velocities are, in general, higher than the velocities measured in overlying dike rocks obtained from the hole during DSDP Leg 83. The velocity gradients observed in Layer 2C result from decreasing porosity with depth and increasing metamorphic grade. The laboratory-measured velocities of the Leg 111 dike rocks are similar to those of dike rocks reported for the Bay of Islands, Samail, and Troodos ophiolites.

Anelastic strain recovery and elastic properties of ODP Leg 123 oceanic basalt samples

A knowledge of rock stress is fundamental for improving our understanding of oceanic crustal mechanisms and lithospheric dynamic processes. However, direct measurements of stress in the deep oceans, and in particular stress magnitudes, have proved to be technically difficult. Anelastic strain recovery measurements were conducted on 15 basalt core samples from Sites 765 and 766 during Leg 123. Three sets of experiments were performed: anelastic strain recovery monitoring, dynamic elastic property measurements, and thermal azimuthal anisotropy observations. In addition, a range of other tests and observations were recorded to characterize each of the samples. One common feature of the experimental results and observations is that apparently no consistent orientation trend exists, either between the different measurements on each core sample or between the same sets of measurements on the various core samples. However, some evidence of correspondence between velocity anisotropy and anelastic strain recovery exists, but this is not consistent for all the core samples investigated. Thermal azimuthal anisotropy observations, although showing no conclusive correlations with the other results, were of significant interest in that they clearly exhibited anisotropic behavior. The apparent reproducibility of this behavior may point toward the possibility of rocks that retain a "memory" of their stress history, which could be exploited to derive stress orientations from archived core. Anelastic strain recovery is a relatively new technique. Because use of the method has extended to a wider range of rock types, the literature has begun to include examples of rocks that contracted with time. Strong circumstantial evidence exists to suggest that core-sample contractions result from the slow diffusion of pore fluids from a preexisting microcrack structure that permits the rock to deflate at a greater rate than the expansion caused by anelastic strain recovery. Both expansions and contractions of the Leg 123 cores were observed. The basalt cores have clearly been intersected by an abundance of preexisting fractures, some of which pass right through the samples, but many are intercepted or terminate within the rock matrix. Thus, the behavior of the core samples will be influenced not only by the properties of the rock matrix between the fractures, but also by how these macro- and micro-scale fractures mutually interact. The strain-recovery curves recorded during Leg 123 for each of the 15 basalt core samples may reflect the result of two competing time dependent processes: anelastic strain recovery and pore pressure recovery. Were these the only two processes to influence the gauge responses, then one might expect that given the additional information required, established theoretical models might be used to determine consistent stress orientations and reliable stress magnitudes. However, superimposed upon these competing processes is their respective interaction with the preexisting fractures that intersect each core. Evidence from our experiments and observations suggests that these fractures have a dominating influence on the characteristics of the recovery curves and that their effects are complex.

Molecular properties of gases of ODP Leg 204 sites

The recognition of finely disseminated gas hydrate in deep marine sediments heavily depends on various indirect techniques because this mineral quickly decomposes upon recovery from in situ pressure and temperature conditions. Here, we discuss molecular properties of closely spaced gas voids (formed as a result of core recovery) and gas hydrates from an area of relatively low gas flux at the flanks of the southern Hydrate Ridge offshore Oregon (ODP Sites 1244, 1245 and 1247). Within the gas hydrate occurrence zone (GHOZ), the concentration of ethane (C2) and propane (C3) in adjacent gas voids shows large variability. Sampled gas hydrates are enriched in C2 relative to void gases but do not contain C3. We suggest that the observed variations in the composition of void gases is a result of molecular fractionation during crystallization of structure I gas hydrate that contains C2 but excludes C3 from its crystal lattice. This hypothesis is used to identify discrete intervals of finely disseminated gas hydrate in cored sediments. Variations in gas composition help better constrain gas hydrate distribution near the top of the GHOZ along with variations in pore water chemistry and core temperature. Sediments near the base of the gas hydrate stability zone are relatively enriched in C2+ hydrocarbon gases. Complex and poorly understood geological and geochemical processes in these deeper sediments make the identification of gas hydrate based on molecular properties of void gases more ambiguous. The proposed technique appears to be a useful tool to better understand the distribution of gas hydrate in marine sediments and ultimately the role of gas hydrate in the global carbon cycle.

Geotechnical properties at DSDP Leg 66 Holes

Delineating the interrelationships between tectonics, sedimentation, and geotechnical properties is particularly important for areas subjected to the dynamic affects of convergence. DSDP Leg 66 drilling within the Middle America Trench complex provided a unique opportunity to investigate these interrelationships along a transect of eight drill sites beginning on the trench outer slope and traversing the trench, trench inner slope, and upper continental slope. Investigations of other convergent margins suggest that deformation occurs most rapidly along the lower trench inner slope and is reflected by the geotechnical properties (Carson, 1977; Seely, 1977; and von Huene, 1979). This study focuses on the geotechnical properties of Middle America Trench sediments and the possible affects of convergence on these properties.

(Table 1) Chemical composition of plagioclase and amphibole-pyroxene containing samples from pyroxene-amphibole-asbestos rock collected in the Hess Deep

Recent sediments with distinct signs of hydrothermal alteration sampled in the Hess Deep(Galapagos Ridge, East Pacific Rise) contained a piece of ash-gray rock, which differed from other rock fragments by degree of consolidation, conchoidal fracture, and had properties of asbestos. Our studies found that the sample represented mixture of asbestos-like pyroxene of diopside-hedenbergite composition, amphibole of tremolite composition and a new mineral, which basic structure consisted of bands of triple pyroxene chains with the radical [Si6O16]. The latter can be regarded as intermediate between amphiboles and layered silicates. Also in some parts of the sample presence of trioctahedral vermiculite-chlorite was indicated. Genesis of the studied asbestos rock is considered from the standpoint of high-temperature hydrothermal-metasomatic alteration of sediment by post-magmatic mineralized halide solutions.

Consolidation properties and strength characteristics of ODP Site 204-1244 sediments

Eight whole-core samples from Ocean Drilling Program Site 1244, Hydrate Ridge, Cascadia continental margin, were provided to Massachusetts Institute of Technology (Cambridge, Massachusetts, USA) for geotechnical characterization. The samples were collected from depths ranging from 5 to 136 meters below seafloor (mbsf). Seven of the eight whole-core samples were located within the gas hydrate stability zone, whereas the eighth sample was located in the free gas zone. Atterberg limits testing showed that the average liquid limit of the soil is 81% and the average plastic limit is 38%, giving an average plasticity index of 43%. The liquid limit is sensitive to oven drying, shown by a drop in liquid limit to 64% when tests were performed on an oven-dried sample. Loss on ignition averages 5.45 wt%. Constant rate of strain consolidation (CRSC) tests were performed to obtain the compression characteristics of the soil, as well as to determine the stress history of the site. CRSC tests also provided hydraulic conductivity and coefficient of consolidation characteristics for these sediments. The compression ratio (Cc) ranges from 0.340 to 0.704 (average = 0.568). Cc is fairly constant to a depth of 79 mbsf, after which Cc decreases downhole. The recompression ratio (Cr) ranges from 0.035 to 0.064 (average = 0.052). Cr is constant throughout the depth range. In situ hydraulic conductivity varies between 1.5 x 10**-7 and 3 x 10**-8 cm/s and shows no trend with depth. Ko-consolidated undrained compression/extension (CKoUC/E) tests were also performed to determine the peak undrained shear strength, stress-strain curve, and friction angle. The normalized undrained strength ranges from 0.29 to 0.35. The friction angle ranges from 27 to 37. Because of the limited amount of soil, CRSC and CKoUC/E tests were also conducted on resedimented specimens.

Physical properties at DSDP Holes 77-535 and 77-540

Tables 1 and 2 contain the data for the physical properties of the material from Sites 535 and 540, respectively. These data are summarized for Site 535 in Table 23 and Figure 31 in the site chapter, Sites 535, 539, and 540. Site 540 data summaries can be found in Table 25 and Figure 37 of the site chapter, Sites 535, 539, and 540.

Physical properties of sediments at DSDP Holes 78-541 and 78-543

Sediment cored within the Barbados subduction complex at Sites 541 and 542 are underconsolidated. Underconsolidation and changes in physical properties of the cored section can be related to excess pore water pressure that equals the lithostatic load at Site 542 and to major thrust faulting observed at Site 541. Apparently, the pore fluids within the subduction complex are absorbing the tectonic shock of underthrusting. Sediment sampled from the reference Site 543 on the adjacent Atlantic Plate are also underconsolidated. However, underconsolidation in Hole 543 is apparently due to the movement of excess nitrogen gas observed deeper in the hole. Excess gas was not observed at Sites 541 and 542.

(Table 1) Magnetic properties for individual samples from ODP Hole 136-843B

We present rock magnetic data on 10 samples recovered from ODP Hole 843B. The 95-m.y.-old basalts have moderately high magnetization values, and Curie temperature measurements show that these basalts have undergone systematic low-temperature oxidation. High values for bulk coercivity indicate that the remanent magnetization is likely to be stable over geological time, and low viscous remanent magnetization coefficients measured for these samples argue that acquisition of viscous remanent magnetization is not likely to be geologically important in these samples. Unfortunately, formation of the Hole 843B crustal section at the beginning of the Cretaceous Normal Magnetic Superchron does not allow any simple test of the hypothesis that a substantial component of chemical remanent magnetization, in the direction of the field present during oxidation, is added soon after formation (Raymond and LaBrecque, 1987, doi:10.1029/JB092iB08p08077).

The impact of ocean acidification and warming on the skeletal mechanical properties of the sea urchin Paracentrotus lividus from laboratory and field observations

Increased atmospheric CO2 concentration is leading to changes in the carbonate chemistry and the temperature of the ocean. The impact of these processes on marine organisms will depend on their ability to cope with those changes, particularly the maintenance of calcium carbonate structures. Both a laboratory experiment (long-term exposure to decreased pH and increased temperature) and collections of individuals from natural environments characterized by low pH levels (individuals from intertidal pools and around a CO2 seep) were here coupled to comprehensively study the impact of near-future conditions of pH and temperature on the mechanical properties of the skeleton of the euechinoid sea urchin Paracentrotus lividus. To assess skeletal mechanical properties, we characterized the fracture force, Young's modulus, second moment of area, material nanohardness, and specific Young's modulus of sea urchin test plates. None of these parameters were significantly affected by low pH and/or increased temperature in the laboratory experiment and by low pH only in the individuals chronically exposed to lowered pH from the CO2 seeps. In tidal pools, the fracture force was higher and the Young's modulus lower in ambital plates of individuals from the rock pool characterized by the largest pH variations but also a dominance of calcifying algae, which might explain some of the variation. Thus, decreases of pH to levels expected for 2100 did not directly alter the mechanical properties of the test of P. lividus. Since the maintenance of test integrity is a question of survival for sea urchins and since weakened tests would increase the sea urchins' risk of predation, our findings indicate that the decreasing seawater pH and increasing seawater temperature expected for the end of the century should not represent an immediate threat to sea urchins vulnerability

Magnetic properties of basalts from DSDP Hole 69-504B

The NRM intensity, AF demagnetization characteristics, hysteresis parameters, initial susceptibility, and thermomagnetic characteristics of 18 basalt specimens from Deep Sea Drilling Project Hole 504B were determined. In six samples, the grain size was large enough to allow microprobe analysis. We conclude (1) that the dominant magnetic mineral is titanomagnetite/titanomaghemite; (2) that, except for the upper few meters of the core where the grains are in the stable monodomain state, the grain size of the magnetic mineral lies in the pseudo-single-domain range (< 10 µm); (3) that maghemitization (i.e., low-temperature (< 350°C) oxidation) has taken place. We discuss possible geological histories.

Physical and geotechnical properties of Norwegian Sea sediments

Sediment composition and rate of deposition are the primary factors responsible for determining the spatial distribution of geotechnical properties on the Wring Plateau. Grain size and depth of burial have no significant influence. Vertical and lateral changes in geotechnical properties are associated with vertical and lateral composition changes in which biogenic silica is the most important variable. Anomalous trends of decreasing density and increasing porosity and water content with depth are associated with increasing silica content downsection. Void ratios, inferred in-situ permeability, and change in void ratio during consolidation testing are relatively high in siliceous sediments and tend to increase as the biogenic silica content increases. Portions of the section are overconsolidated, probably as a result of changes in sediment accumulation rates. However, the higher permeabilities of siliceous sediments may also be a factor influencing consolidation state.

Summary of physical properties on cores used for petrofabric analyses triaxial experiments at DSDP Leg 67 Holes

Deformation features within the cores are studied with a view towards elucidating the structure of the Middle America Trench along the transect drilled during Leg 67. Where possible, inferences are made as to the physical environment of deformation. Extensional tectonics prevails in the area of the seaward slope and trench. Fracturing and one well-preserved normal fault are found mostly within the lower Miocene chalks, at the base of the sedimentary section. These chalks have high porosities (40%-60%) and water content (30%-190%, based on % dry wt.). Experimental triaxial compression tests conducted on both dry and water-saturated samples of chalk from Holes 495 and 499B show that only in the saturated samples is more brittle behavior observed. Brittle failure of the chalks is greatly facilitated by pore fluid pressures that lead to low effective pressures. Additional embrittlement (weakening) can take place as a result of the imposed extensional stress resulting from bending of a subducting elastic oceanic plate. The chalks exhibit, in a landward direction, an increase in density and mechanical strength and a decrease in water content. These changes are attributed to mechanical compaction that may have resulted from tectonic horizontal compression. The structure of the landward slope is not well understood because the slope sites had to be abandoned due to the presence of gas hydrate. The relationship of the chaotic, brittle deformation (observed in the cores from Hole 494A) at the base of the landward slope to tectonic processes remains unclear. The deformation observed on the slope sites (Holes 496 and 497) is mostly fracturing and near-vertical sigmoidal veinlets. These are interpreted as being the result of gas/fluid overpressurization due to the decomposition of the gas hydrate, and not due to tectonic loading of accreted sediments. Aside from four small displacement (less than 1cm) reverse faults observed in the lower Miocene chalks (which may be the product of soft-sediment deformation), there is a noticeable absence of structures reflecting a dominance of horizontal (tectonic) compression along the transect drilled. The absence of such features, the lack of continuity of sediment types across the trench-landward slope, and the normal stratigraphic sequence in Hole 494A do not support any known accretionary model.

Geotechnical properties of sediments at DSDP Leg 84 Holes

The geotechnical characteristics of 22 sediment samples from Leg 84 sites were studied in an effort to associate these with processes active along the Middle America slope and with sedimentation mechanisms. Geotechnical properties measured include water content, porosity, bulk density, Atterberg limits, consolidation characteristics, permeability, and vane shear strength. A majority of samples obtained from Sites 565, 568, and 570 show significant disturbance resulting from degassing. This disturbance apparently results in underconsolidation, although other mechanisms such as excess pore pressures generated from the subduction process can also contribute to this state. Overconsolidated sediments were found at Sites 565, 566, and 569. The overconsolidated sediments at Sites 565 and 569 may result from downslope transport mechanisms rearranging and stressing the sediment mass under consideration. The sediment condition at Site 566 is probably a result of eroded overburden: an estimated 87 m of overlying sediments may have been removed. Geotechnical and permeability relationships with depth are consistent with those found for other hemipelagic sediments of silty clay to clayey silt textures.