Summary of physical properties on cores used for petrofabric analyses triaxial experiments at DSDP Leg 67 Holes


Autoria(s): Dengo, Carlos A
Cobertura

MEDIAN LATITUDE: 12.682764 * MEDIAN LONGITUDE: -90.952884 * SOUTH-BOUND LATITUDE: 12.496300 * WEST-BOUND LONGITUDE: -91.037700 * NORTH-BOUND LATITUDE: 13.063700 * EAST-BOUND LONGITUDE: -90.795200 * DATE/TIME START: 1979-05-17T00:00:00 * DATE/TIME END: 1979-06-18T00:00:00

Data(s)

02/08/1982

Resumo

Deformation features within the cores are studied with a view towards elucidating the structure of the Middle America Trench along the transect drilled during Leg 67. Where possible, inferences are made as to the physical environment of deformation. Extensional tectonics prevails in the area of the seaward slope and trench. Fracturing and one well-preserved normal fault are found mostly within the lower Miocene chalks, at the base of the sedimentary section. These chalks have high porosities (40%-60%) and water content (30%-190%, based on % dry wt.). Experimental triaxial compression tests conducted on both dry and water-saturated samples of chalk from Holes 495 and 499B show that only in the saturated samples is more brittle behavior observed. Brittle failure of the chalks is greatly facilitated by pore fluid pressures that lead to low effective pressures. Additional embrittlement (weakening) can take place as a result of the imposed extensional stress resulting from bending of a subducting elastic oceanic plate. The chalks exhibit, in a landward direction, an increase in density and mechanical strength and a decrease in water content. These changes are attributed to mechanical compaction that may have resulted from tectonic horizontal compression. The structure of the landward slope is not well understood because the slope sites had to be abandoned due to the presence of gas hydrate. The relationship of the chaotic, brittle deformation (observed in the cores from Hole 494A) at the base of the landward slope to tectonic processes remains unclear. The deformation observed on the slope sites (Holes 496 and 497) is mostly fracturing and near-vertical sigmoidal veinlets. These are interpreted as being the result of gas/fluid overpressurization due to the decomposition of the gas hydrate, and not due to tectonic loading of accreted sediments. Aside from four small displacement (less than 1cm) reverse faults observed in the lower Miocene chalks (which may be the product of soft-sediment deformation), there is a noticeable absence of structures reflecting a dominance of horizontal (tectonic) compression along the transect drilled. The absence of such features, the lack of continuity of sediment types across the trench-landward slope, and the normal stratigraphic sequence in Hole 494A do not support any known accretionary model.

Formato

application/zip, 2 datasets

Identificador

https://doi.pangaea.de/10.1594/PANGAEA.817572

doi:10.1594/PANGAEA.817572

Idioma(s)

en

Publicador

PANGAEA

Direitos

CC-BY: Creative Commons Attribution 3.0 Unported

Access constraints: unrestricted

Fonte

Supplement to: Dengo, Carlos A (1982): A structural analysis of Cores from the Leg 67 transect across the Middle America Trench - offshore Guatemala. In: Abouin, J; von Huene, R; et al. (eds.), Initial Reports of the Deep Sea Drilling Project (U.S. Govt. Printing Office), 67, 651-666, doi:10.2973/dsdp.proc.67.133.1982

Palavras-Chave #67-494A; 67-495; 67-496; 67-497; 67-499B; 67-500; Comment; Confining; Deep Sea Drilling Project; Density, wet bulk; Depth; DEPTH, sediment/rock; DRILL; Drilling/drill rig; DSDP; Effective confining; Event; Failure modes are defined in the following manner: ductile, if the sample was deformed by homogeneous macroscopic flow; transitional, if the sample was deformed along numerous slip planes but still with some ductility; and brittle, if the sample failed by one or more thoroughgoing rupture surfaces and with no ductile deformation; Flame photometry; Gamma-ray attenuation porosity evaluator (GRAPE); Glomar Challenger; Label; Leg67; North Pacific/SLOPE; North Pacific/TRENCH; ODP sample designation; Operation mode; Op mode; P; Poros; Porosity; Pressure, stress; Sample code/label; Water content of dry mass; Water dm; WBD
Tipo

Dataset