Incorporação de nanopartículas de óxido de zinco a um cimento de ionômero de vidro por meio da calcinação: avaliação de propriedades mecânicas e físicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Anion dopant effects on the structure and performance of polyethersulfone membranes

In this work, the effect of various casting solution salt dopants with similar cations, but different anions: (NaPO3)(6), Na2SO4, Na2CO3, NaCl, and NaF, on the morphology and performance of polyethersulfone ultrafiltration membranes was evaluated. The phase inversion process was used to produce all membranes using an 18% polyethersulfone in n-methylpyrrolidone casting solution and water as the non-solvent. Scanning electron microscopy (SEM) images of the membrane cross-section and surface pores were used to determine the specific anion effects on membrane morphology. The SEM images depicted significant changes to the membrane internal structure and pore size with respect to the type and concentration of the casting solution anion dopant. Membrane permeability, molecular weight cut-off, alginate retention, and susceptibility to fouling were evaluated using ultrapure water dead-end and ultrapure water, aqueous polyethylene glycol, aqueous sodium alginate, and natural surface water cross-flow filtration tests. Among the anions evaluated, hexametaphosphate doped at 1% w/w to the polymer resulted in the membrane with highest dead-end permeability at 490 LMH-bar (2- to 3-fold greater than the control), greatest alginate retention at 96.5%, and lowest susceptibility to fouling. The significant increase in membrane performance indicates that the hexametaphosphate anion has great potential to be used as a membrane casting solution dopant. It was also clearly demonstrated that membrane pore morphological characteristics can be effectively used to predict drinking water treatment performance. (C) 2012 Elsevier B.V. All rights reserved.

Caratterizzazione di membrane da nanofiltrazione

Nanofiltration (NF) is a pressure-driven membrane process, intermediate between reverse osmosis and ultrafiltration. Commercially available polymeric membranes have been used in a wide range of applications, such as drinking, process industry and waste water treatment. For all the applications requiring high stability and harsh washing procedures inorganic membranes are preferred due to their high chemical inertia. Typically, γ – Al2O3 as well as TiO2 and ZrO2 selective layers are used; the latter show higher chemical stability in a wide range of pH and temperatures. In this work the experimental characterization of two different type of membrane has been performed in order to investigate permeation properties, separation performance and efficiency with aqueous solutions containing strong inorganic electrolytes. The influence of salt concentration and feed pH as well as the role of concentration polarization and electrolyte type on the membrane behavior are investigated. Experimentation was performed testing a multi–layer structured NF membrane in α-Al2O3, TiO2 and ZrO2, and a polymeric membrane, in polyamide supported on polysulfone, with binary aqueous solutions containing NaCl, Na2SO4 or CaCl2; the effect of salt composition and pH in the feed side was studied both on flux and salt rejection. All the NF experimental data available for the two membranes were used to evaluate the volumetric membrane charge (X) corresponding to each operative conditions investigated, through the Donnan Steric Pore Model and Dielectric Exclusion (DSPM&DE). The results obtained allow to understand which are the main phenomena at the basis of the different behaviors observed.

Mass transport in polymers

The study of mass transport in polymeric membranes has grown in importance due to its potential application in many processes such as separation of gases and vapors, packaging, controlled drug release. The diffusion of a low molecular weight species in a polymer is often accompanied by other phenomena like swelling, reactions, stresses, that have not been investigated in all their aspects yet. Furthermore, novel materials have been developed that include inorganic fillers, reactive functional groups or ions, that make the scenery even more complicated. The present work focused on the experimental study of systems where the diffusion is accompanied by other processes; suitable models were also developed to describe the particular circumstances in order to understand the underlying concepts and be able to design the performances of the material. The effect of solvent-induced deformation in polymeric films during sorption processes was studied since the dilation, especially in constrained membranes, can cause the development of stresses and therefore early failures of the material. The bending beam technique was used to test the effects of the dilation and the stress induced in the polymer by penetrant diffusion. A model based on the laminate theory was developed that accounts for the swelling and is able to predict the stress that raise in the material. The addition of inorganic fillers affects the transport properties of polymeric films. Mixed matrix membranes based on fluorinated, high free volume matrices show attractive performances for separation purposes but there is a need for deeper investigation of the selectivity properties towards gases and vapors. A new procedure based on the NELF model was tested on the experimental data; it allows to predict solubility of every penetrant on the basis of data for one vapor. The method has proved to be useful also for the determination of the diffusion coefficient and for an estimation of the permeability in the composite materials. Oxygen scavenging systems can overcome lack of barrier properties in common polymers that forbids their application in sensitive applications as food packaging. The final goal of obtaining a membrane almost impermeable to oxygen leads to experimental times out of reach. Hence, a simple model was developed in order to describe the transport of oxygen in a membrane with also reactive groups and analyze the experimental data collected on SBS copolymers that show attractive scavenging capacity. Furthermore, a model for predicting the oxygen barrier behavior of a film formed as a blend of OSP in a common packaging material was built, considering particles capable of reactions with oxygen embedded in a non-reactive matrix. Perfluorosulphonic acid ionomers (PFSI) are capturing attention due to a high thermal and chemical resistance coupled with very peculiar transport properties, that make them appropriate to be used in fuel cells. The possible effect of different formation procedure was studied together with the swelling due to water sorption since both water uptake and dilation can dramatically affect the fuel cells performances. The water diffusion and sorption was studied with a FTIR-ATR spectrometer that can give deeper information on the bonds between water molecules and the sulphonic hydrophilic groups and, therefore, on the microstructure of the hydrated ionomer.

Flüssigkristalline Ionomere zum Aufbau von Multischichtstrukturen

Die vorliegende Arbeit beschäftigt sich mit der Synthese und Charakterisierung von nematischen und smektischen LC-Polyestern, die mit ionischen Gruppen funktionalisiert wurden. Als ionische Gruppen wurden Phosphonsäure-salze und Phosphonium- oder Ammoniumgruppen verwendet. Je nach Polymerrückgrat erhält man LC-Ionomere, bei denen die ionischen Gruppen entweder an das Mesogen oder an den Hauptkettenspacer gebunden sind. Diese LC-Ionomere können zusammen mit amorphen Polyelektrolyten oder anorganischen Schichtmineralien für den Multischichtaufbau durch alternierende Adsorption von Polykation und Polyanion aus der Lösung verwendet werden (Methode von G. Decher). Die Multischichtbildung konnte mittels UV-Spektroskopie, IR-Spektroskopie, Kontaktwinkel-Messungen, Röntgenreflexionsmessungen und Oberflächen Plasmonen-Spektroskopie verfolgt werden. Die Subschichten sind zwischen 25 und 55 Å dick und hängen z.B. von der Polarität des Lösungsmittels ab. Erste cis-trans Isomerisierungen und Photoorientierungs-Versuche wurden durchgeführt.

Ionomere zum Aufbau funktioneller Oberflächen

Im ersten Teil der Arbeit wurden Ionomere durch aufeinanderfolgende polymeranaloge Reaktionen eines Reaktivesterpolymers mit verschiedenen primären bzw. sekundären Aminen synthetisiert. Polarisationsmikroskopische Untersuchungen zeigten, dass diese Ionomere sowohl über thermotrope als auch über lyotrope flüssigkristalline Eigenschaften verfügen. Anschließend wurden mit der 'self-assembly'-Methode Multischichtfilme aus den Ionomeren und hochgeladenen Polyelektrolyten sowie aus entgegengesetzt geladenen Ionomeren aufgebaut. Bei Röntgen-reflexionsmessungen an den Multischichtfilmen konnten winkelabhängige Modulationen der Strahlungsintensität beobachtet werden. Es ist zu vermuten, dass es sich bei diesen Modulationen um Überlagerungen von Kiessig-Ringen und Bragg-Peaks handelt, was ein Indiz dafür ist, dass regel-mäßige Subschichten in den Filmen existieren. Das Konzept der polymeranalogen Reaktionen eines Reaktivesterpolymers mit verschiedenen primären Aminen wurde außerdem dazu benutzt, Polymere zur Modifikation von Cadmiumselenid-Nanokristallen herzustellen. Hierbei konnte zum einen gezeigt werden, dass Nanokristalle direkt mit aminogruppenhaltigen Polymeren modifiziert werden können, zum anderen ist es auch möglich kationische Ionomere auf Nanokristallen mit Mercaptoessigsäure-Liganden zu adsorbieren. Im letzten Teil der Arbeit wurden ionische triazinhaltige Polymere hergestellt und elektrochemisch charakterisiert. Die hergestellten Polymere sind sehr leicht reduzierbar. Anschließend wurden aus den triazinhaltigen Polymeren und entgegengesetzt geladenen Polyelektrolyten ebenfalls Multischichtfilme hergestellt.

Solid-state NMR investigation of phosphonic acid based proton conducting materials

In this work, new promising proton conducting fuel cell membrane materials were characterized in terms of their structure and dynamic properties using solid-state nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction. Structurally different, phosphonic acid (PA) containing materials were systematically evaluated for possible high-temperature operation (e.g. at T>100°C). Notably, 1H, 2H and 31P magic angle spinning (MAS) NMR provided insight into local connectivities and dynamics of the hydrogen bonded network, while packing arrangements were identified by means of heteronuclear dipolar recoupling techniques.rnThe first part of this work introduced rather crystalline, low molecular weight ionomers for proton conducting membranes, where six different geometries such as line, triangle, screw, tetrahedron, square and hexagon, were investigated. The hexagon was identified as the most promising geometry with high-temperature bulk proton conductivities in the range of 10-3 Scm-1 at a relative humidity of 50%. However, 2H NMR and TGA-MS data suggest that the bulk proton transport is mainly due to the presence of crystal water. Single crystal X-ray data revealed that in the tetrahedron phosphonic acids form tetrameric clusters isolating the mobile protons while the phosphonic acids in the hexagon form zigzag-type pathways through the sample.rnThe second part of this work demonstrates how acid-base pairing and the choice of appropriate spacers may influence proton conduction. Different ratios of statistical copolymers of poly (vinylphosphonic acid) and poly (4-vinylpyridine) were measured to derive information about the local structure and chemical changes. Though anhydrous proton conductivities of all statistical copolymers are rather poor, the conductivity increases to 10-2 S cm-1 when exposing the sample to relative humidity of 80%. In contrast to PVPA, anhydride formation of phosphonic acids in the copolymer is not reversible even when exposing the sample to a relative humidity of 100%.rnIn addition, the influence of both spacers and degree of backbone crystallinity on bulk proton conductivity was investigated. Unlike in systems such as poly benzimidazole (PBI), spacers were inserted between the protogenic groups along the backbone. It was found that dilution of the protogenic groups decreases the conductivity, but compared to PVPA, similar apparent activation energies for local motions were obtained from both variable temperature 1H NMR and impedance spectroscopy data. These observations suggest the formation of phosphonic acid clusters with high degrees of local proton motion, where only a fraction of motions contribute to the observable bulk proton conductivity. Additionally, it was shown that gradual changes of the spacer length lead to different morphologies.rnIn summary, applying advanced solid-state NMR and X-ray analysis, structural and dynamic phenomena in proton conducting materials were identified on a molecular level. The results were discussed with respect to different proton conduction mechanisms and may contribute to a more rational design or improvement of proton conducting membranes.rn

Adhesión de ionómeros vítreos convencionales a dentina tratada con distintas sustancias

El objetivo de este trabajo fue evaluar la fuerza adhesiva de los ionómeros vítreos convencionales a la dentina tratada con ácido fosfórico, con ácido poliacrílico y con solución de hipoclorito de sodio. Los ensayos se realizaron sobre dentina de premolares extraídos por razones ortodóncicas o periodontales, los cuales se asignaron al azar en tres grupos de 10 elementos cada uno. A cada grupo se le practicó un tratamiento distinto (descalcificación, desproteinización o eliminación del barro dentinario). Sobre cada espécimen se le adhirió un cilindro de ionómero vítreo convencional preparado según las especificaciones de su fabricante. Posteriormente las muestras fueron sometidas a fuerzas de cargas de corte utilizando una máquina de ensayos universal (Instron). Los resultados obtenidos fueron sometidos a análisis de ANOVA de una entrada y a post test de comparación múltiple de Tukey. Por lo que puede expresarse que no hubo diferencia estadísticamente significativa (p>0,05) en la fuerza adhesiva de los ionómeros vítreos que fueron adheridos a dentina con tratamiento de ácido poliacrílico, y los que fueron adheridos a dentina con tratamiento de descalcificación (acción del ácido fosfórico). Se encontró diferencia estadísticamente significativa en las muestras adheridas a dentina tratadas con poliacrílico y ácido fosfórico (p<0.01 y p<0.05 respectivamente), con respecto a las que fueron tratadas con hipoclorito.

Geochemistry and radionuclide content of sediment and water samples obtained from the Ob and Irtysh river, Russia

This paper reports the results of the investigations of 2006-2007 on the distribution and migration forms of artificial radionuclides and chemical elements in the Ob-Irtysh water system. Three regions were studied. One of them is a local segment of the Ob River upstream from the confluence with the Irtysh River; its investigation allowed us to estimate the general radioecological state of the aquatic environment affected by the activity of the Tomsk 7 plant. The second region is a local segment of the Irtysh River upstream from its confluence with the Ob River, where the influence of emissions from the NPO Mayak could be estimated. The third region is the water area of the Ob River after its confluence with the Irtysh River. It characterizes the real level of radioactive and chemical contamination of the middle reaches of the Ob River. In order to explain horizontal variations in the distribution of radionuclides in the upper layer of bottom sediments collected at various sites, the results of sorption-kinetic experiments with radioactive tracers in the precipitate-solution system were used. The investigation of the migration forms of trace elements and radionuclides occurring in river water was based on the method of tangential-flow membrane filtration. Chemical element contents were determined in 400-ml water samples. A set of Millipore polysulfone membranes with pore sizes of 8, 1.2, 0.45, 0.1, and 0.025 µm was employed. Taking into account the ultralow specific concentrations of radionuclides in the water, they were analyzed in 300-500 litre samples using Millipore polysulfone membranes with pore sizes of 0.45 µm and 15 kDa. This allowed us to estimate the percentages of cesium-137 and plutonium-239, 240 in the suspended particulate fraction, colloids, and dissolved species.

Design of advanced reverse osmosis and nanofiltration membranes for water purification

Most commercially available reverse osmosis (RO) and nanofiltration (NF) membranes are based on the thin film composite (TFC) aromatic polyamide membranes. However, they have several disadvantages including low resistance to fouling, low chemical and thermal stabilities and limited chlorine tolerance. To address these problems, advanced RO/NF membranes are being developed from polyimides for water and wastewater treatments. The following three projects have resulted from my research. (1) Positively charged and solvent resistant NF membranes. The use of solvent resistant membranes to facilitate small molecule separations has been a long standing industry goal of the chemical and pharmaceutical industries. We developed a solvent resistant membrane by chemically cross-linking of polyimide membrane using polyethylenimine. This membrane showed excellent stability in almost all organic solvents. In addition, this membrane was positively charged due to the amine groups remaining on the surface. As a result, high efficiency (> 95%) and selectivity for multivalent heavy metal removal was achieved. (2) Fouling resistant NF membranes. Antifouling membranes are highly desired for “all” applications because fouling will lead to higher energy demand, increase of cleaning and corresponding down time and reduced life-time of the membrane elements. For fouling prevention, we designed a new membrane system using a coating technique to modify membrane surface properties to avoid adsorption of foulants like humic acid. A layer of water-soluble polymer such as polyvinyl alcohol (PVA), polyacrylic acid (PAA), polyvinyl sulfate (PVS) or sulfonated poly(ether ether ketone) (SPEEK), was adsorbed onto the surface of a positively charged membrane. The resultant membranes have a smooth and almost neutrally charged surface which showed better fouling resistance than both the positively charged NF membranes and commercially available negatively charged NTR-7450 membrane. In addition, these membranes showed high efficiency for removal of multivalent ions (> 95% for both cations and anions). Therefore, these antifouling surfaces can be potentially used for water softening, water desalination and wastewater treatment in a membrane bioreactor (MBR) process. (3) Thermally stable RO membranes. Commercial RO membranes cannot be used at temperature higher than 45°C due to the use of polysulfone substrate, which often limits their applications in industries. We successfully developed polyimides as the membrane substrate for thermally stable RO membranes due to their high thermal resistance. The polyimide-based composite polyamide membranes showed desalination performance comparable to the commercial TFC membrane. However, the key advantage of the polyimide-based membrane is its high thermal stability. As the feed temperature increased from 25oC to 95oC, the water flux increased 5 - 6 times while the salt rejection almost kept constant. This membrane appears to provide a unique solution for hot water desalination and also a feasible way to improve the water productivity by increasing the operating temperature without any drop in salt rejection.

Selluloosamembraanien kehittäminen ja testaus

Tämän työn tavoitteena oli selvittää, kuinka selluloosan lisääminen vaikuttaa polysulfonirunkoisiin membraaneihin. Lisäksi työssä selvitettiin selluloosamembraanien modifiointia kitosaanilla ja bentoniitilla. Työssä muodostettiin membraanit faasi-inversiotekniikalla. Selluloosamembraanien valmistuksessa jauhettu selluloosa liuotettiin ioniseen nesteeseen. Sekä polysulfonista että selluloosasta valmistetuille membraaneille määritettiin puhdasvesivuot ja retentiot. Retention määrittämiseen käytettiin malliaineena dekstraanin vesiliuosta. Lisäksi määriteltiin polysulfonipohjaisten membraanien hydrofiilisyys tutkimalla membraanien pintojen ja vesipisaroiden välisiä kontaktikulmia. Polysulfonimembraaneihin lisätyn selluloosan havaittiin pienentävän puhdasvesivuota ja kasvattavan hydrofiilisyyttä mitä enemmän selluloosaa oli membraanimatriisissa. Kaikkien selluloosalla modifioitujen membraanien retentiot olivat suurempia kuin modifioimattoman polysulfonimembraanin. Kitosaanilla modifioitujen selluloosamembraanien valmistus ei onnistunut johtuen luultavasti kitosaanin liian suuresta partikkelikoosta. Bentoniitilla modifioitujen membraanien vuot olivat merkittävästi suuremmat sekä niiden retentiot pienemmät verrattuna modifioimattomaan selluloosamembraaniin. Tämä johtui luultavasti siitä, että bentoniitin lisääminen aiheutti membraanirakenteeseen reikiä.