Effect of steeping conditions (sulfur dioxide, lactic acid, and temperature) on starch yield, starch quality, and germ quality from the Intermittent Milling and Dynamic Steeping process (IMDS) for a Brazilian corn hybrid

Effect of lactic acid, SO2, temperature, and their interactions were assessed on the dynamic steeping of a Brazilian dent corn (hybrid XL 606) to determine the ideal relationship among these variables to improve the wet-milling process for starch and corn by-products production. A 2x2x3 factorial experimental design was used with SO2 levels of 0.05 and 0.1% (w/v), lactic acid levels of 0 and 0.5% (v/v), and temperatures of 52, 60, and 68degreesC. Starch yield was used as deciding factor to choose the best treatment. Lactic acid added in the steep solution improved the starch yield by an average of 5.6 percentage points. SO2 was more available to break down the structural protein network at 0.1% than at the 0.05% level. Starch-gluten separation was difficult at 68degreesC. The lactic acid and SO2 concentrations and steeping temperatures for better starch recovery were 0.5, 0.1, and 52degreesC, respectively. The Intermittent Milling and Dynamic Steeping (IMDS) process produced, on average, 1.4% more starch than the conventional 36- hr steeping process. Protein in starch, oil content in germ, and germ damage were used as quality factors. Total steep time can be reduced from 36 hr for conventional wet-milling to 8 hr for the IMDS process.

Desenvolvimento de um reator fotoquímico aplicável no tratamento de efluentes fenólicos presentes na indústria do petróleo

With water pollution increment at the last years, so many progresses in researches about treatment of contaminated waters have been developed. In wastewaters containing highly toxic organic compounds, which the biological treatment cannot be applied, the Advanced Oxidation Processes (AOP) is an alternative for degradation of nonbiodegradable and toxic organic substances, because theses processes are generation of hydroxyl radical based on, a highly reactivate substance, with ability to degradate practically all classes of organic compounds. In general, the AOP request use of special ultraviolet (UV) lamps into the reactors. These lamps present a high electric power demand, consisting one of the largest problems for the application of these processes in industrial scale. This work involves the development of a new photochemistry reactor composed of 12 low cost black light fluorescent lamps (SYLVANIA, black light, 40 W) as UV radiation source. The studied process was the photo-Fenton system, a combination of ferrous ions, hydrogen peroxide, and UV radiation, it has been employed for the degradation of a synthetic wastewater containing phenol as pollutant model, one of the main pollutants in the petroleum industry. Preliminary experiments were carrier on to estimate operational conditions of the reactor, besides the effects of the intensity of radiation source and lamp distribution into the reactor. Samples were collected during the experiments and analyzed for determining to dissolved organic carbon (DOC) content, using a TOC analyzer Shimadzu 5000A. The High Performance Liquid Chromatography (HPLC) was also used for identification of the cathecol and hydroquinone formed during the degradation process of the phenol. The actinometry indicated 9,06⋅1018 foton⋅s-1 of photons flow, for 12 actived lamps. A factorial experimental design was elaborated which it was possible to evaluate the influence of the reactants concentration (Fe2+ and H2O2) and to determine the most favorable experimental conditions ([Fe2+] = 1,6 mM and [H2O2] = 150,5 mM). It was verified the increase of ferrous ions concentration is favorable to process until reaching a limit when the increase of ferrous ions presents a negative effect. The H2O2 exhibited a positive effect, however, in high concentrations, reaching a maximum ratio degradation. The mathematical modeling of the process was accomplished using the artificial neural network technique

Efeito da adição de colesterol e ecdisona na produção in vitro do baculovírus spodoptera frugiperda MNPV

Among the pests that attack corn crop in Brazil, there is Spodoptera frugiperda (JE Smith, 1797) (Lepidoptera: Noctuidae), known as fall armyworm, which is the major corn pest. Due to genetic instability during serial passage of baculoviruses in insect cell culture, the viral bioinseticides in vitro production development is the greatest challenge for mass production of this bioproduct. Successive passages of virus using extracellular viruses (BVs), necessary during viral bioinseticides production scaling up, leads to the appearance of aberrant forms of virus, a process so called as "passage effect ". The main consequence of passage effect is the production of occlusion bodies (OB) decrease, preventing its production using in vitro process. In this study, it was carried out a serial passage of baculovirus Spodoptera frugiperda multiple nucleopolyhedrovirus, isolate 18, using Sf21 cells. A decrease in the production of occlusion bodies from 170 to 92 in the third to fourth passage was observed. A factorial experimental design (22) was employed to verify the influence of two input variables, concentration of the hormone 20 - hydroxyecdysone (CH) and cholesterol (CC) on the values of response variables (volumetric and the specific OB production) of the process, seeking to define the optimum operating ranges trying to reverse or minimize the passage effect. The result indicated a negative influence of the cholesterol addition and positive effect in the hormone supplementation which the optimum range found for the concentrations studied were 8 to 10μg/mL and 5 to 6.5 mg / mL, for cholesterol and hormone concentrations respectively. New experiments were performed with addition of hormone and cholesterol in order to check the influence of these additives on the OB production independently. While the best result obtained from the factorial experiment was 9.4 x 107 OB/mL and 128.4 specific OB/cell, with the addition of only 6μg/mL 20-hydroxyecdysone these concentrations increased to 1.9 x 108 OB/mL and 182.9 OB/cell for volumetric and specific OB production, respectively. This result confirms that the addition of the hormone 20-hydroxyecdysone enhances the SfMNPV in vitro production process performance using Sf21 cells

Produção de enzimas por fungos em fermentação semi-sólida utilizando bagaço de coco e pedúnculo de caju como substratos

The production of enzymes by microorganisms using organic residues is important and it can be associated with several applications such as food and chemical industries and so on. The objective of this work is the production of CMCase, Xylanase, Avicelase and FPase enzymes by solid state fermentation (SSF) using as substrates: bagasse of coconut and dried cashew stem. The microorganisms employed are Penicillium chrysogenum and an isolated fungus from the coconut bark (Aspergillus fumigatus). Through the factorial design methodology and response surface analysis it was possible to study the influence of the humidity and pH. For Penicillium chrysogenum and the isolated fungus, the coconut bagasse was used as culture medium. In another fermentation, it was used the mixture of coconut bagasse and cashew stem. Fermentations were conducted using only the coconut bagasse as substrate in cultures with Penicillium chrysogenum fungus and the isolated one. A mixture with 50% of coconut and 50% of cashew stem was employed only for Penicillium chrysogenum fungus, the cultivation conditions were: 120 hours at 30 °C in BOD, changing humidity and pH values. In order to check the influence of the variables: humidity and pH, a 2 2 factorial experimental design was developed, and then two factors with two levels for each factor and three repetitions at the central point. The levels of the independent variables used in ascending order (-1, 0, +1), to humidity, 66%, 70.5% and 75% and pH 3, 5 and 7, respectively. The software STATISTICA TM (version 7.0, StatSoft, Inc.) was used to calculate the main effects of the variables and their interactions. The response surface methodology was used to optimize the conditions of the SSF. A chemical and a physic-chemical characterization of the coconut bagasse have determined the composition of cellulose (%) = 39.09; Hemicellulose (%) = 23.80, Total Lignin (%) = 36.22 and Pectin (%) = 1.64. To the characterization of cashew stem, the values were cellulose (g) = 15.91 Hemicellulose (%) = 16.77, Total Lignin (%) = 30.04 and Pectin (%) = 15.24. The results indicate the potential of the materials as substrate for semisolid fermentation enzyme production. The two microorganisms used are presented as good producers of cellulases. The results showed the potential of the fungus in the production of CMCase enzyme, with a maximum of 0.282 UI/mL and the Avicelase enzyme the maximum value ranged from 0.018 to 0.020 UI/ mL, using only coconut bagasse as substrate. The Penicillium chrysogenum fungus has showed the best results for CMCase = 0.294 UI/mL, FPase = 0.058 UI/mL, Avicelase = 0.010 UI/mL and Xylanase = 0.644 UI/ mL enzyme, using coconut bagasse and cashew stem as substrates. The Penicllium chrysogenum fungus showed enzymatic activities using only the coconut as substrate for CMCase = 0.233 UI/mL, FPase = 0.031 to 0.032 UI/ mL, Avicelase = 0.018 to 0.020 UI/mL and Xylanase = 0.735 UI/ mL. Thus, it can be concluded that the used organisms and substrates have offered potential for enzyme production processes in a semi-solid cultivation

Fenologics characteristics of the Siciliano lemon tree on two rootstocks influenced by liming and boron addition

O presente estudo foi desenvolvido na UNESP/Botucatu, São Paulo, Brasil, num solo identificado como Oxisol, onde foram plantadas mudas de limoeiro Siciliano (C. limon) enxertadas em laranjeira Azeda (C. aurantium) e em limoeiro Cravo (C. limonia). O experimento consistiu em três níveis de saturação por bases (50%, 70% e 90%) e três doses de boro (0,5; 1,5 e 4,5 mg dm-3) no plantio em esquema fatorial de 3x3x2, com quatro repetições. Houve diferentes comportamentos entre os porta-enxertos no que se refere à composição mineral de folhas de limoeiro Siciliano , bem como, no desenvolvimento do sistema radicular, sendo maior na laranjeira azeda em relação ao limoeiro cravo. Não houve nenhum efeito na interação de níveis de saturação por bases e doses de boro para nenhum dos parâmetros avaliados.

Concepção de um secador rotatório para secagem do cefalotórax do camarão

The present work has as objective the knowledge of the process of drying of the cephalothorax of shrimp to give support the industry to make possible the use of this byproduct. In this sense, the process conditions in this tray dryer and spouted bed were analyzed. With these results, it was projected and constructs a dryer with specific characteristics for the drying of the cephalothorax. The desorption isotherms were obtained by the dynamic method in the temperatures of 20, 35 and 50º C and in the interval of 10-90% of relative humidity. It was observed that the product in form of powder can be conserved with larger stability for lower relative humidity to 40%. The curves of drying of the dryer of fixed bed were adjusted for the models: single exponential, biparametric exponential and Page. The model biparametric exponential more adequately described all the drying conditions studied. The tests carry out in spouted bed showed high drying rate for the material in the paste form in beds active dynamicly-fluid, provely the necessity of a feeding in shorter intervals of time to increase the thermal efficiency of the process. The projected dryer, be considered the obtained results, it was a rotary dryer with inert bed, feed co-current, discharge in cyclone to take place the separation gas-solid, and feed carry out in intervals of 2 minutes. The optimization of the equipment projected it was accomplished used the complete factorial experimental design 24, this had as independent variables temperature velocity of the air, feed flow rate and encapsulated concentration (albumin), as variables answers the thermal efficiency, the moisture content of obtained powder, total time of test and the efficiency of production of powder in several points of processing. The results showed that the rotary dryer with inert bed can present, also, good results if applied industrially

Screening of Formulation Variables for the Preparation of Poly(epsilon-caprolactone) Nanocapsules Containing the Local Anesthetic Benzocaine

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Digestibility of feeds containing sorghum, with and without tannin, for broiler chickens submitted to three room temperatures

The traditional method of total excreta collection was applied, using 30 to 40 day old male Ross 308 broiler chickens. One hundred and eight broiler chickens were used, randomly assigned to a 3x3 factorial experimental design. The room temperatures were 14 C (cold), 25 °C (thermoneutral) and 32 °C (hot) and the three diets were 100% maize, 100% sorghum with tannin and 100% sorghum without tannin, with four replicates of each. The digestibility coefficients for the dry matter, crude protein, crude fibre, neutral detergent fibre, acid detergent fibre, ether extract, mineral matter and nitrogen-free extract were determined. It was observed that all the digestibility coefficients were higher in the hot chamber and lower in the cold chamber, and that these values tended to be higher for maize.

Laboratory study on the bioremediation of diesel oil contaminated soil from a petrol station

O objetivo do presente estudo foi investigar possíveis métodos para aumentar a taxa de biodegradação aeróbia de hidrocarbonetos (tratamentos ex-situ). Neste trabalho, processos de biorremediação foram aplicados a um solo arenoso com alto nível de contaminação ocasionada por um vazamento de um tanque de armazenamento de óleo diesel subterrâneo em um posto de combustíveis. Experimentos em escala laboratorial (respirômetros de Bartha) foram utilizados para avaliar a biodegradação do óleo diesel. Estímulo da biodegradação foi realizado utilizando-se as técnicas de bioestímulo (adição de soluções de nitrogênio e fósforo ou surfactante Tween 80) e de bioaumento (consórcio bacteriano isolado de um sistema de landfarming). Para investigar as interações entre os fatores otimizadores, e encontrar a melhor combinação entre esses agentes, o estudo foi baseado em um delineamento experimental fatorial completo. A eficiência de biodegradação foi simultaneamente medida com dois métodos: respirométrico (produção de CO2 microbiano) e cromatografia gasosa. Testes de toxicidade aguda com Daphnia similis foram aplicados para examinar a eficiência dos processos em termos de geração de produtos menos tóxicos. Resultados mostraram que todas as estratégias de biorremediação aceleraram a biorremediação natural do solo contaminado e os melhores resultados foram obtidos quando os tratamentos tinham adição de nutrientes. Dados respirométricos indicaram uma máxima mineralização de hidrocarbonetos de 19,8%, obtida com a combinação dos três agentes, com uma remoção de hidrocarbonetos totais de petróleo (TPH) de 45,5% em 55 dias de tratamento. No final dos experimentos, duas espécies predominantes de bactéria foram isoladas e identificadas como Staphylococcus hominis e Kocuria palustris.

Optimization of photo-polymerized sol gel monolithic stationary phases prepared in polyacrylate-coated fused-silica capillaries for capillary electrochromatography

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Physicochemical properties of maize starch obtained from intermittent milling and dynamic steeping (IMDS) under various steeping conditions

Physicochemical properties of maize starch obtained under different steeping conditions by intermittent milling and dynamic steeping process (IMDS) were studied. Brazilian dent maize (hybrid XL 606) was milled using a 2x2x3 factorial experimental design with two lactic acid levels (0.0 and 0.55%, v/v), two SO2 levels (0.05 and 0.1%, w/v), and three temperatures (52, 60, and 68degreesC). Properties of starch obtained by conventional wet-milling process (36 hr at 52degreesC, 0.55% lactic acid, and 0.2% SO2) were used for comparison. Starch protein content and solubility increased with presence of lactic acid, while swelling power decreased. Higher SO2 concentration (0.1%) had the same effect as lactic acid on some properties. Steeping temperatures of 60 and 68degreesC increased solubility and most of the thermal properties but reduced swelling power, suggesting stronger starch annealing during IMDS at these temperatures. Some thermal changes on starch granules were visualized by scanning electron microscopy (SEM) at 60 and 68degreesC. Amylose content as well as pasting properties were affected by steeping factors and interactions. Starches from IMDS and conventional wet-milling processes were similar in most properties, indicating that IMDS provides starch with quality similar to that from conventional milling.

Surface area of the tip of the enterocytes in small intestine mucosa of broilers submitted to early feed restriction and supplemented with glutamine

A total of 640 one-day-old male Cobb chicks were used to evaluate the effects of early feed restriction and glutamine on villi density and tip surface of enterocytes in the small intestine of broilers. A two-factor factorial experimental design with glutamine and feed restriction as main factors was used. Treatments consisted of quantitative feed restriction at 30% of ad libitum intake from 7 to 14 days of age, and glutamine addition at 1% in the diet from 1 to 28 days of age. Sections of the small intestine (duodenum, jejunum, ileum) were collected at 14 and 21 days of age for analyses by scanning and transmission electron microscopy. Villi density decreased with age and increased in cranial-caudal direction. Glutamine increased villi density in the small intestine. Microvilli density and height decreased with age. Glutamine increased microvilli width. The jejunum was the segment with the largest surface area of the tip of the enterocytes, followed by the duodenum and the ileum. Feed restriction decreased the surface area of the tip of the enterocytes in the small intestine at 14 and at 21 days of age. Glutamine supplemented in the feed increased the surface area of the tip of the enterocytes of the jejunum and ileum at 21 days of age. © Asian Network for Scientific Information, 2007.

Use of soybean oil fry waste for economical biosurfactant production by isolated Pseudomonas aeruginosa using response surface methodology

The present study sought biotensoactive production from soybean oil fry waste using Pseudomonas aeruginosa ATCC 10145 and Pseudomonas aeruginosa isolated from the soil of a petroleum station having undergone gasoline and diesel oil spills. The results of the experiments were analyzed using a complete factorial experimental design, investigating the concentration of soybean oil waste, ammonia sulfate and residual brewery yeast. Assays were performed in 250-mL Erlenmeyer beakers containing 50 mL of production medium, maintained on a rotary shaker at 200 rpm and a temperature of 30±1 °C for a 48-hour fermentation period. Biosurfactant production was monitored through the determination of rhamnose, surface tension and emulsification activity. The Pseudomonas aeruginosa ATCC 10145 strain and isolated Pseudomonas aeruginosa were able to reduce the surface tension of the initial mexlium from 61 mN/m to 32.5 mN/m and 30.0 mN/m as well as produce rhamnose at concentrations of 1.96 and 2.89 g/L with emulsification indices of 96% and 100%, respectively.

Influence of medium composition in the production of ethanol by Zymomonas mobilis

The production of ethanol using Zymomonas mobilis had been reported to be three to four times larger than with Saccharomyces cereviseae. The influence of pH, temperature and composition of the means of fermentation are parameters that can direct the metabolism for the production of ethanol. The objective of this study was to evaluate the production of ethanol by Zymomonas mobilis CCT 4494, by variations of the initial pH, temperature and concentrations KCl, K 2SO4, MgSO4, CaCl2 and sucrose, by a factorial experimental design of type 27-2, according to the model proposed by Box et al. (1978). For this, the broth of sugar cane was used as sole carbon source, because it is cheap and easily accessible in the region of São José do Rio Preto, São Paulo State. According to the experimental design, the bacteria Zymomonas mobilis CCT 4494 has adapted in the fermentation mean containing high concentrations of sucrose, and supported the change of pH and temperature of fermentation. The highest amount of ethanol produced was 8.89 mg mL-1. This is not similar to the levels of secondary metabolites produced by Zymomonas mobilis CCT 4494.

Time and temperature on the storage of oocytes from jundiá catfish, Rhamdia quelen

The objective of this study was to evaluate the effects of three water and storage temperatures on the oocytes of the jundiá catfish, Rhamdia quelen. A factorial experimental design over time, with treatments completed in triplicate every 48 h, was used (5 × 3 × 3 × 3) to study the exposure of the oocytes to temperatures of 15, 25 and 35. °C and activated with water at 15, 25 and 35. °C each at 0, 45, 90, 135 and 180 minutes post-collection. Linear regression analysis for the response surface model indicated an interaction (p<0.05) between time and temperature of exposure with greater values for fertilization, hatching and normal larvae rates at the time of oocyte collection (70.2 ± 8.4% fertilized oocytes, 66.7 ± 29.4% hatched eggs and 30.3 ± 25.0% normal larvae). According to the statistical model, the water temperature that resulted in the highest fertilization rate was 25.6. °C (p<0.05). The rates of fertilization, hatching and normal larvae correlated positively (p<0.05) with one another, showing that these parameters can be used in the measurement of oocyte quality. Artificial fertilization of oocytes is recommended immediately after collection; if storage is necessary, it should be carried out at 15. °C. © 2011 Elsevier B.V.