Método dinâmico aplicado para antenas cilíndricas

Nowadays there has been a major breakthrough in the aerospace area, with regard to rocket launches to research, experiments, telemetry system, remote sensing, radar system (tracking and monitoring), satellite communications system and insertion of satellites in orbit. This work aims at the application of a circular cylindrical microstrip antenna, ring type, and other cylindrical rectangular in structure of a rocket or missile to obtain telemetry data, operating in the range of 2 to 4 GHz, in S-band. Throughout this was developed just the theoretical analysis of the Transverse transmission line method which is a method of rigorous analysis in spectral domain, for use in rockets and missiles. This analyzes the spread in the direction "ρ" , transverse to dielectric interfaces "z" and "φ", for cylindrical coordinates, thus taking the general equations of electromagnetic fields in function of e [1]. It is worth mentioning that in order to obtain results, simulations and analysis of the structure under study was used HFSS program (High Frequency Structural Simulator) that uses the finite element method. With the theory developed computational resources were used to obtain the numerical calculations, using Fortran Power Station, Scilab and Wolfram Mathematica ®. The prototype was built using, as a substrate, the ULTRALAM ® 3850, of Rogers Corporation, and an aluminum plate as a cylindrical structure used to support. The agreement between the measured and simulated results validate the established processes. Conclusions and suggestions are presented for continuing this work

Contribuições ao método de rastreamento de máxima potência para sistemas fotovoltaicos

The scarcity of natural resources and the search for alternative energy sources promote a rapid change in the energy world. Among the renewable energy sources, solar energy is the most promising, presenting technology of greatest growth rate nowadays. Researchers around the world are seeking ways to facilitate their progress, developing technologies with higher efficiency and lower cost. As a contribution to global progress, this master thesis proposes the development of a strategy of maximum power tracking based on perturbation and observation method for photovoltaic systems. The proposed control strategy is based on active power balance of the system, with a reduced number of sensors. It also allows the PV system to act as a regulator of the power quality at the point of commom coupling (PCC), compensating the harmonic distortion and power factor of the current netw

Aplicação prática do método de sintonia de controladores PID utilizando o método do relé com histerese

The area of research and development involving the PID tune of controllers is an active area in the academic and industrial sectors yet. All this due to the wide use of PID controllers in the industry (96% of all controllers in the industry is still PID). Controllers well tuned and tools to monitor their performance over time with the possibility of selftuning, become an item almost obligatory to maintain processes with high productivity and low cost. In a globalized world, it is essential for their self survival. Although there are several new tools and techniques that make PID tune, in this paper will explore the PID tune using the relay method, due its good acceptance in the industrial environment. In addition, we will discuss some techniques for evaluation of control loops, as IAE, ISE, Goodhart, the variation of the control signal and index Harris, which are necessary to propose new tuning for control loops that have a low performance. Will be proposed in this paper a tool for tuning and self tuning PID. Will be proposed in this paper a PID auto-tuning software using a relay method. In particular, will be highlighted the relay method with hysteresis. This method has shown tunings with satisfactory performance when applied to the didactic, simulated and real plants

Caracterização de cerâmicas porosas de alumina reforçada com zircônia produzidas pelo método da réplica

Porous ceramics have many applications: thermal insulation, catalytic support, materials to fire protection, filters, and others. There are many techniques to production of ceramic filters. One technique to obtain ceramic filters is the replication method. This method consists in the impregnation of polymeric foam with ceramic slurry followed by a heating treatment that will burn out the organic elements and sintering of the material, resulting of a replication of the original foam. To perform their functions ceramic filters must satisfy mechanical requirements and permeability parameters (darcian k1 and no-darcian k2). The permeability and the strength of the ceramic material are dependent of the pore size and pore distribution. To the use at high temperatures the evaluation of mechanical properties in these temperatures is necessary. In this work the mechanical behavior of two commercial porous ceramics (10 and 40 poros per inch) was studied these materials were submitted to compression and four-point flexure test (room temperature, at 1000 °C, after thermal shock). Density and porosity measurements, permeability tests and microstructural analysis by scanning electronic microscopy (SEM) were realized. The Results showed that the decrease of mechanical strength of these materials, when submitted to thermal shock, occur for propagation of new cracks from cracks pre-existing and the permeability depends of the pore size

Análise do comportamento mecânico de espumas cerâmicas a base de alumina obtidas pelo método da réplica

Ceramics with porous cellular structure, called ceramic foams, have a potential use in several applications, such as: thermal insulation, catalyst supports, filters, and others. Among these techniques to obtain porous ceramics the replication method is an important process. This method consists of impregnation of a sponge (usually polymer) with ceramic slurry, followed by a heat treatment, which will happen the decomposition of organic material and sintering the ceramic material, resulting in a ceramic structure which is a replica of impregnated sponge. Knowledge of the mechanical properties of these ceramics is important for these materials can be used commercially. Gibson and Ashby developed a mathematical model to describe the mechanical behavior of cellular solids. This model wasn´t for describing the ceramics behavior produced by the replica method, because it doesn´t consider the defects from this type of processing. In this study were researched mechanical behavior of porous alumina ceramics obtained by the replica method and proposed modifications to the model of Gibson and Ashby to accommodate this material. The polymer sponge used in processing was characterized by thermogravimetric analysis and scanning electron microscopy. The materials obtained after sintering were characterized by mechanical strength tests on 4-point bending and compression, density and porosity and by scanning electron microscopy. From these results it was evaluated the mechanical strength behavior compared to Gibson and Ashby model for solid cellular structure and was proposed a correction of this model through a factor related to struts integrity degree, which consider fissures present in the structure of these materials besides defects geometry within the struts

Método de Otimização Topológica em Estruturas Tridimensionais

The topology optimization problem characterize and determine the optimum distribution of material into the domain. In other words, after the definition of the boundary conditions in a pre-established domain, the problem is how to distribute the material to solve the minimization problem. The objective of this work is to propose a competitive formulation for optimum structural topologies determination in 3D problems and able to provide high-resolution layouts. The procedure combines the Galerkin Finite Elements Method with the optimization method, looking for the best material distribution along the fixed domain of project. The layout topology optimization method is based on the material approach, proposed by Bendsoe & Kikuchi (1988), and considers a homogenized constitutive equation that depends only on the relative density of the material. The finite element used for the approach is a four nodes tetrahedron with a selective integration scheme, which interpolate not only the components of the displacement field but also the relative density field. The proposed procedure consists in the solution of a sequence of layout optimization problems applied to compliance minimization problems and mass minimization problems under local stress constraint. The microstructure used in this procedure was the SIMP (Solid Isotropic Material with Penalty). The approach reduces considerably the computational cost, showing to be efficient and robust. The results provided a well defined structural layout, with a sharpness distribution of the material and a boundary condition definition. The layout quality was proporcional to the medium size of the element and a considerable reduction of the project variables was observed due to the tetrahedrycal element

Simulação numérica da interação entre uma nuvem incidente de vórtices e uma aerofólio através do método dos vórtices

The study of aerodynamic loading variations has many engineering applications, including helicopter rotor blades, wind turbines and turbo machinery. This work uses a Vortex Method to make a lagrangian description of the a twodimensional airfoil/ incident wake vortex interaction. The flow is incompressible, newtonian, homogeneus and the Reynolds Number is 5x105 .The airfoil is a NACA 0018 placed a angle of attack of the 0° and 5°simulates with the Painel Method with a constant density vorticity panels and a generation poit is near the painel. The protector layer is created does not permit vortex inside the body. The vortex Lamb convection is realized with the Euler Method (first order) and Adans-Bashforth (second order). The Random Walk Method is used to simulate the diffusion. The circular wake has 366 vortex all over positive or negative vorticity located at different heights with respect to the airfoil chord. The Lift was calculated based in the algorithm created by Ricci (2002). This simulation uses a ready algorithm vatidated with single body does not have a incident wake. The results are compared with a experimental work The comparasion concludes that the experimental results has a good agrement with this papper

Método rápido de extração de DNA de bactérias

Desenvolveu-se um método rápido para extração de DNA de bactérias, que ao contrário de outros métodos, não requer o uso de enzimas, como lisozima e proteinase K, previamente, utilizado-se o carbonato de silício (carborundum) como agente físico para efetuar a quebrar da parede celular da bactéria. Com este método conseguiu-se extrair DNA bacteriano num menor tempo, além de mais rápido, ele mostrou-se mais simples e econômico, quando comparado aos métodos convencionais. O DNA obtido pode ser utilizado para diversas finalidades relacionadas ao DNA de bactérias, obtendo-se uma quantidade razoável de DNA, que varia de 725 µg/mL a 1170 µg/mL por cada 0,1 g de célula bacteriana, com ótima qualidade.

Método de preparo das sementes de mamoneira (Ricinus communis L.) para o teste de tetrazólio

O teste de tetrazólio é um método rápido e eficaz para avaliar a viabilidade e o vigor de sementes. O presente trabalho teve por objetivo padronizar o método de preparo das sementes de mamoneira (Ricinus communis L.) para a avaliação do potencial fisiológico pelo teste de tetrazólio. Foram testados os seguintes métodos de preparo das sementes: corte longitudinal mediano através do tegumento, endosperma e embrião; corte longitudinal diagonal sem atingir o eixo embrionário; remoção do tegumento; remoção do tegumento com corte longitudinal mediano através do endosperma e embrião; e remoção do tegumento com corte longitudinal mediano, paralelo aos cotilédones, através do endosperma e embrião. Antes dos preparos, as sementes foram pré-condicionadas entre papel toalha umedecido por 18 horas a 30ºC, e após os preparos, as sementes foram imersas na solução de tetrazólio na concentração de 0,5% e mantidas em câmara escura a 35ºC para o desenvolvimento da coloração. Avaliou-se a uniformidade da coloração das sementes após cada preparo, por meio da comparação entre eles. Para a avaliação do potencial fisiológico das sementes de mamoneira pelo teste de tetrazólio o método indicado de preparo é a remoção do tegumento, com posterior corte longitudinal e mediano, no sentido do comprimento, através do endosperma e embrião.

Atividade radicular da soja: definição de um método

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)