Investigation of two-proton emission from excited states of the odd-Z nucleus P-28 by complete-kinematics measurements

An experiment to study exotic two-proton emission from excited levels of the odd-Z nucleus P-28 was performed at the National Laboratory of Heavy Ion Research-Radioactive Ion Beam Line (HIRFL-RIBLL) facility. The projectile P-28 at the energy of 46.5 MeV/u was bombarding a Au-197 target to populate the excited states via Coulomb excitation. Complete-kinematics measurements were realized by the array of silicon strip detectors and the CsI + PIN telescope. Two-proton events were selected and the relativistic-kinematics reconstruction was carried out. The spectrum of relative momentum and opening angle between two protons was deduced from Monte Carlo simulations. Experimental results show that two-proton emission from P-28 excited states less than 17.0 MeV is mainly two-body sequential emission or three-body simultaneous decay in phase space. The present simulations cannot distinguish these two decay modes. No obvious diproton emission was found.

Development of multi-channel gated integrator and PXI-DAQ system for nuclear detector arrays

A multi-channel gated integrator and PXI based data acquisition system have been developed for nuclear detector arrays with hundreds of detector units. The multi-channel gated integrator can be controlled by a programmable Cl controller. The PXI-DAQ system consists of NI PXI-1033 chassis with several PXI-DAQ cards. The system software has a user-friendly GUI which is written in C language using LabWindows/CVI under Windows XP operating system. The performance of the PXI-DAQ system is very reliable and capable of handling event rate up to 40 kHz. (C) 2010 Elsevier B.V. All rights reserved.

A high performance Time-of-Flight detector applied to isochronous mass measurement at CSRe

A high performance Time-of-Flight detector has been designed and constructed for isochronous mass spectrometry at the experimental Cooler Storage Ring (CSRe) The detector has been successfully used in an experiment to measure the masses of the N approximate to Z approximate to 33 nuclides near the proton drip-line Of particular interest is the mass of As-65 A maximum detection efficiency of 70% and a time resolution of 118 +/- 8 Ps (FWHM) have been achieved in the experiment The dependence of detection efficiency and signal average pulse height (APH) on atomic number Z has been studied The potential of APH for Z identification has been discussed (C) 2010 Elsevier B V All rights reserved

4p探测器的研制及测试

本文主要分为两部分，第一部分是有关兰州多阵列4π探测器的设计，它主要是用于中能核反应的实验研究，因而它是根据中能核反应的特点来设计的，具有大的立体角的覆盖，好的空间分辨，低的能量阈以及较大范围的能量、动量测量和良好的粒子分辨等特点。第二部分主要介绍了此4π探测器的单元探测器的研制，其单元主要是由快塑料闪烁体和CsI(Tl)晶体组成的叠层望远镜及由快塑料与慢塑料闪烁体组成的叠层望远镜，主要包括快塑料闪烁体(BS498x)的研制，碘化铯(铊)晶体的选择，光子在闪烁体和光导中传输效率的模拟计算，光电倍增管Base电路的设计，最后是利用HIRFL加速的~(18)O和~(40)Ar束流轰击Ni靶产生的核反应产物对上述两种单元进行了测试，取得非常好的粒子分辨和轻粒子同位素分辨。

用于RIBLL和CSR的气体探测的研制

气体探测器是历史最悠久的核探测器之一气体探测器具有成本低廉、制备简单、性能可靠和使用方便等特点。而且气体探测器的形状和尺寸可任意设计，厚度可随气体气压的变化而改变，适合做大面积位置灵敏、大立本角探测和有较宽的动态测量范围。所以气体探测器在各自的应用范围内发挥着巨大的作用。在兰州放射性束流线（RIBLL）上开展次级束实验的过程中，束流的定位和发散度测定都是非常重要的。我们研制了两种高性能的双维位置灵勘平行板雪崩计数器（PPAC），一种为传统的三个极板结构，另外一种为五个极板的多极结构，分别适用于较重粒子和轻粒子的位置测量。对于五个极板的多极结构的探测器，灵敏面积为100mm×100mm，采用电荷分除法读出位置，我们用3组分α源测试，工作气体选用异丁烷。测试在6.5mb气压下，位置分辨为0.55mm（FWHM），探测效率大于99.2％，位置离散小于士0.2mm。一系列的性能指标都达到了同类探测器的最好水平。该探测器和以前研制的三极板PPAC的性能均已满足RIBLL的要求，将会用作RIBLL重要的束诊元件和位置探测器。同时改进后还能在即将建成的兰州重离子加速器冷却存储环（HIRFL-CSR）上的束流诊断过程中发挥重要的作用。同时，为在RIBLL上开展超重元素和超重核素的合成实验研制了一种多阳极横向场气体电离室（MAIC）。在100mbP10气体下，对应第四块大灵敏区域，5.806MeV~(244)Cm的α粒子的能量损失为1.30MeV，得出该探测器的能量分辨为41.1keV（FwHM），相对分辨为3.16％。该探测器适合于较重粒子的鉴别，性能指标已经满足RIBLL鉴glI灼子的要求。

八单元一维位置灵敏雪崩室

In the experiment of nuclear reaction, it is important to measure the mass, charge, energy and emitted direction of particles. For multiparameter measurement, we must use a detector or a group of detectors which can give the time, energy, and position information. The Large Area position sensitive Ionization Chamber(LAIC) is one of the eight experiment terminals of HIRFL. It is built for researching nuclear reactions from low energy to intermediate energy. It is an excellent equipment for energy measurements and atomic number identification of emitted fragments in this energy region. It is also designed to give the time and position information of the emitted fragments by itself. Obviously, an IC can not supply a good timing signal. Moreover, the mechanical installation is different from the original design by some other reasons. In this case, it is not enough to obtain the correct direction information of the emitted fragments. To obtain good timing signals and the correct direction information, some modifications must be made. It is well known that a PPAC can give us excellent timing signals. It also can be easily built as a position sensitive detector. For this reason, a specially designed PPAC is installed in the entrance of the LAIC. For the different purposes, two types of PPACs were designed and tested. Both are OCTPSACs (OCTunit one dimension Position Sensitive Avalanche Counter). In this paper, both OCTPSACs will be introduced. Based on the requirements of the LAIC, the OCTPSACs consist of eight position sensitive PPACs. Each PPAC has an anode and a cathode. In both cases, the sizes are same. But different type of cathodes are used. In one type of OCTPSAC, its cathode is made of wire plane. It consists of gold-plated tungsten wires with the diameter of 20μm, spaced 0.5 mm apart from each other. The anode is a mylar foil which was evaporated by gold layer with the thickness of 50μg/cm~2 mounted on a printed plate in the shape of rectangle. the thickness of mylar foil is 1.5μm. The gap between anode and cathode is 3mm. The performance of the OCTPSAC has been tested by using a ~(252)Cf source in flowing isobutylene gas at the pressure of 3.4mb. The intrinsic time resolution of 289ps and position resolution of 2 mm have been obtained. In another type of OCTPSAC, the cathode is made of mylar foil, which is composed of gold strip by vacuume evaporation method with a special mask on the mylar foil. The thickness and the width of the gold strip is 50μg/cm~2 and 1.7mm. The strips are spaced 0.3 mm apart from each other. The anode is the same as the former type. We have obtained the time resolution of 296ps and position resolution of 2mm by using ~(241)Am-a source when the gas pressure is 6 mb and high voltage is 600V. The working gas is heptane

空间望远镜系统的设计及硅锂探测器的研制

论文的结构分为空间望远镜系统的设计和硅（锂）探测器研制两个部分。第一部分主要介绍了空间望远镜系统的设计，该空间望远镜系统能鉴别Z≤26、M≤56范围内的空间带电粒子，该系统的设计在国内是首例，它将使我国空间高能带电粒子的鉴别和测量上一个新的台阶；第二个部分主要介绍适合于探测空间粒子的硅（锂）探测器的研制及其性能的测试过程。该探测器的研制成功为空间高能带电粒子的探测提供了必要的准备。 我们已经提供给空间科学与应用研究中心二十多块硅（锂）探测器。我们用ThC'-C源和137Cs源对硅（锂）探测器进行了测试，我们在120V时便可得到137Cs电子谱；我们在250V常温常压得到α粒子谱，其能量分辨可好于37Kev，长期加压测试时硅（锂）探测器的反向电流变化稳定，在持续20天加压250V时，其中直径为12mm的硅（锂）探测器的电流变化可达1.10±0.50微安，信噪比可达420倍。

小麦抗旱生态分类中适合性聚类方法的研究

探索了适合于小麦品种抗旱生态分类的聚类方法 .选用 2 1个农艺性状和 15个冬小麦品种 (系 ) ,在聚类分析的各环节上 ,通过采用不同的策略 ,大规模进行了各种分类结果的比较 .结果表明 ,在与专家经验分类接近程度上 ,数据转换方法中 ,原始数据法依次大于普通相关阵基础上的方差极大正交旋转法、Promax斜交旋转法、主成份法 ;相似性度量上 ,欧氏距离大于马氏距离 ;聚类方式上 ,对应分析法和模糊聚类法大于最短距离法、最长距离法、类平均法 ;所有可组合的方法中 ,以对应分析法和直接用原始数据的模糊聚类法的分类结果最接近专家经验分类 .结合各方法理论上优缺点的分析与检验 ,认为这两种方法也是较理想的方法 .

实物界面下的虚拟装配

基于增强现实技术,将实物用户界面应用到虚拟装配系统中,在单摄像头的条件下,将虚拟零件模型加载至实物标记上,用户通过操作实物标记来控制虚拟模型,完成装配过程。相比于传统的虚拟装配交互方式,增强了用户操作的切实感。根据装配任务需求设计了4类实物标记。提出了3种交互技术,包括接近性原理,匹配约束信息提示与判定,以及视点控制等,并且结合碰撞检测来实现精确而又自然的虚拟装配。该系统可以帮助设计人员方便地对产品设计进行分析和改进,降低用户的学习难度。

Thermoluminescence characteristics of rare-earth-doped LiCaBO3 phosphor

LiCaBO3 was synthesized by high-temperature solid-state reaction. The influence of different rare earth dopants, i.e. Dy3+, Tb3+. TM3+ and Ce3+, on thermoluminescence (TL) of LiCaBO3 phosphor was discussed. We studied the TL properties and some dosimetric characteristics of Ce3+-activated LiCaBO3 phosphor in detail. The effect of the concentration of Ce3+ on TL was investigated, the result of which showed that the optimum Ce3+ concentration was 1 mol%. The TL kinetic parameters of LiCaBO3:0.01 Ce3+ were studied by computer glow curve deconvolution (CGCD) method.

The effect of annealing treatment on performance of interdiffused organic photovoltaic devices

We fabricated the interdiffused organic photovoltaic devices, which composed of poly (2-methoxy-5-(2'-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) and buckminsterfullerene (C-60), by annealing treatment. After annealing, C60 diffused into the MEH-PPV layer, in consequence, MEH-PPV/C-60 interfacial area was increased and their interface became closer proximity. The results lead to reduce reverse-bias saturation current (J(s)), and increase the open-circuit voltage (V-OC) and the short-circuit current (J(SC)).

Amphiphilic Core-Shell Nanocarriers Based On Hyperbranched Poly(ester amide)-star-PCL: Synthesis, Characterization, and Potential as Efficient Phase Transfer Agent

Amphiphilic biodegradable star-shaped polymer was conveniently prepared by the Sn(Oct)(2)-catalyzed ring opening polymerization of c-caprolactone (CL) with hyperbranched poly(ester amide) (PEA) as a macroinitiator. Various monomer/initiator ratios were employed to vary the length of the PCL arms. H-1 NMR and FTIR characterizations showed the successful synthesis of star polymer with high initiation efficiency. SEC analysis using triple detectors, RI, light scattering, and viscosity confirmed the controlled manner of polymerization and the star architecture.

Thermoluminescence characteristics of NaSr4(BO3)(3):Ce3+ under beta-ray irradiation

The thermoluminescence (TL) properties of Ce3+ doped NaSr4(BO3)(3) phosphor under the beta-ray irradiation were reported. The polycrystalline sample was synthesized by high temperature solid-state reaction. The TL glow curve of NaSr4(BO3)(3):Ce3+ phosphor was composed of only one peak. TL kinetic parameters of NaSr4(BO3)(3):Ce3+ were deduced by the peak shape method, the activation energy (E) was 0.590 eV and the frequency factor was 1.008x10(6) s(-1). TL dose response was linear in the range of measurement. The 3-dimensional (3D) TL emission spectrum was also recorded, the emission spectrum consisted of two bands located at 441 and 479 nm respectively, corresponding to the characteristic 4f(0)5d(1)-> F-2((5/2,7/2)) transitions of the Ce3+ ion. The fading behavior of the NaSr4(BO3)(3):Ce3+ phosphor over a period of 15 d was also studied.

Facile synthesis and characterization of hyperbranched poly(ether amide)s generated from Michael addition polymerization of in situ created AB(2) monomers

A new straightforward strategy for synthesis of novel hyperbranched poly (ether amide)s from readily available monomers has been developed. By optimizing the reaction conditions, the AB(2)-type monomers were formed dominantly during the initial reaction stage. Without any purification, the AB(2) intermediate was subjected to further polymerization in the presence (or absence) of an initiator, to prepare the hyperbranched polymer-bearing multihydroxyl end-groups. The influence of monomer, initiator, and solvent on polymerization and the molecular weight (MW) of the resultant polymers was studied thoroughly. The MALDI-TOF MS of the polymers indicated that the polymerization proceeded in the proposed way. Analyses of H-1 NMR and C-13 NMR spectra revealed the branched structures of the polymers obtained. These polymers exhibit high-moderate MWs and broad MW distributions determined by gel permeation chromatography (GPC) in combination with triple detectors, including refractive index, light scattering, and viscosity detectors. In addition, the examination of the solution behavior of these polymers showed that the values of intrinsic viscosity [eta] and the Mark-Houwink exponent a were remarkably lower compared with their linear analogs, because of their branched nature.

AMPEROMETRIC DETECTION OF CATECHOLAMINES WITH LIQUID-CHROMATOGRAPHY AT A NOVELLY CONSTRUCTED PRUSSIAN BLUE CHEMICALLY MODIFIED ELECTRODE

A novel Prussian blue chemically modified electrode (CME) was constructed and characterized for liquid chromatography electrochemical detection (LCEC) of catecholamines. Both anodic and cathodic peaks could be obtained by monitoring at constant applied potential at anodic and slightly cathodic potential ranges (0.3-0.7 and -0.2-0.1 V vs. SCE), respectively. When arranged in a series configuration, using the modified electrodes as generating and collecting detectors, extremely high effective collection efficiencies of 0.91 (for norepinephrine) and 0.58 (for dihydroxyphenylacetic acid) were achieved in dual-electrode LCEC for catecholamines; and a linear response range over 3 orders of magnitude and a detection limit of 10 pg were obtained with a downstream CME as the indicating detector.