Thermal shock resistance of air plasma sprayed thermal barrier coatings

The spallation resistance of an air plasma sprayed (APS) thermal barrier coating (TBC) to cool-down/reheat is evaluated for a pre-existing delamination crack. The delamination emanates from a vertical crack through the coating and resides at the interface between coating and underlying thermally grown oxide layer (TGO). The coating progressively sinters during engine operation, and this leads to a depth-dependent increase in modulus. Following high temperature exposure, the coating is subjected to a cooling/reheating cycle representative of engine shut-down and start-up. The interfacial stress intensity factors are calculated for the delamination crack over this thermal cycle and are compared with the mode-dependent fracture toughness of the interface between sintered APS and TGO. The study reveals the role played by microstructural evolution during sintering in dictating the spallation life of the thermal barrier coating, and also describes a test method for the measurement of delamination toughness of a thin coating. © 2014 Elsevier Ltd.

Quantitative structure-property relationships for octanol-air partition coefficients of polychlorinated naphthalenes, chlorobenzenes and p,p '-DDT

The octanol-air partition coefficient (K-OA) is a key descriptor of chemicals partitioning between the atmosphere and environmental organic phases. Quantitative structure-property relationships (QSPR) are necessary to model and predict KOA from molecular structures. Based on 12 quantum chemical descriptors computed by the PM3 Hamiltonian, using partial least squares (PLS) analysis, a QSPR model for logarithms of K-OA to base 10 (log K-OA) for polychlorinated naphthalenes (PCNs), chlorobenzenes and p,p'-DDT was obtained. The cross-validated Q(cum)(2) value of the model is 0.973, indicating a good predictive ability of the model. The main factors governing log K-OA of the PCNs, chlorobenzenes, and p,p'-DDT are, in order of decreasing importance, molecular size and molecular ability of donating/accepting electrons to participate in intermolecular interactions. The intermolecular dispersive interactions play a leading role in governing log K-OA. The more chlorines in PCN and chlorobenzene molecules, the greater the log K-OA values. Increasing E-LUMO (the energy of the lowest unoccupied molecular orbital) of the molecules leads to decreasing log K-OA values, implying possible intermolecular interactions between the molecules under study and octanol molecules. (C) 2002 Elsevier Science Ltd. All rights reserved.

Quantitative relationships between molecular structures, environmental temperatures and octanol-air partition coefficients of PCDD/Fs

A concise quantitative model that incorporates information on both environmental temperature M and molecular structures, for logarithm of octanol-air partition coefficient (K-OA) to base 10 (logK(OA)) of PCDDs, was developed. Partial least squares (PLS) analysis together with 14 quantum chemical descriptors were used to develop the quantitative relationships between structures, environmental temperatures and properties (QRSETP) model. It has been validated that the obtained QRSETP model can be used to predict logK(OA) of other PCDDs. Molecular size, environmental temperature (T), q(+) (the most positive net atomic charge on hydrogen or chlorine atoms in PCDD molecules) and E-LUMO (the energy of the lowest unoccupied molecular orbital) are main factors governing logK(OA) of PCDD/Fs under study. The intermolecular dispersive interactions and thus the size of the molecules play a leading role in governing logK(OA). The more chlorines in PCDD molecules, the greater the logK(OA) values. Increasing E-LUMO values of the molecules leads to decreasing logK(OA) values, implying possible intermolecular interactions between the molecules under study and octanol molecules. Greater q(+) values results in greater intermolecular electrostatic repulsive interactions between PCDD and octanol molecules and smaller logK(OA) values. (C) 2002 Elsevier Science B.V. All rights reserved.

Quantitative structure-property relationships for octanol-air partition coefficients of polychlorinated biphenyls

Based on nine quantum chemical descriptors computed by PM3 Hamiltonian, using partial least squares analysis, a significant quantitative structure-property relationship for the logarithm of octanol-air partition coefficients (log K-OA) of polychlorinated biphenyls (PCBs) was obtained. The cross-validated Q(cum)(2) value of the model is 0.962, indicating a good predictive ability. The intermolecular dispersive interactions and thus the size of the PCB molecules play a key role in governing log K-OA. The greater the size of PCB molecules, the greater the log K-OA values. Increasing E-LUMO (the energy of the lowest unoccupied molecular orbital) values of the PCBs leads to decreasing log K-OA values, indicating possible interactions between PCB and octanol molecules. Increasing Q(Cl)(+) (the most positive net atomic charges on a chlorine atom) and Q(C)(-) (the largest negative net atomic charge on a carbon atom) values of PCBs results in decreasing log K-OA values, implying possible intermolecular electrostatic interactions between octanol and PCB molecules. (C) 2002 Elsevier Science Ltd. All rights reserved.

Proposal of an Ultracompact Triplexer Using Photonic Crystal Waveguide with an Air Holes Array

We propose an ultracompact triplexer based on a shift of the cutoff frequency of the fundamental mode in a planar photonic crystal waveguide (PCW) with a triangular lattice of air holes. The shift is realized by modifying the radii of the border holes adjacent to the PCW core. Some defect holes are introduced to control the beam propagation. The numerical results obtained by the finite-difference time-domain method show that the presented triplexer can separate three specific wavelengths, i.e. 1310, 1490 and 1550 nm with the extinction ratios higher than - 18 dB. The designed device with a size as compact as 12 mu m x 6.5 mu m is feasible for the practical application, and can be utilized in the system of fiber to the home.

Fabrication of nanoscale metallic air-bridges by introducing a SiO2 sacrificial layer

A new method to fabricate nanoscale metallic air-bridges has been investigated. The pillar patterns of the air-bridge were defined on a SiO2, sacrificial layer by electron-beam lithography combined with inductively coupled plasma etching. Thereafter, the span (suspended part between the pillars) patterns were defined with a second electron-beam exposure on a PMMA/PMMA-MAA resist system. The fabrication process was completed by subsequent metal electron-beam evaporation, lift-off in acetone, and removal of the sacrificial layer in a buffered hydrofluoric (HF) solution. Air-bridges with two different geometries (line-shaped and cross-shaped) were studied in detail. The narrowest width of the air-bridges was around 200 nm, and the typical length of the air-bridges was 2-5 mu m. The advantages of our method are the simplicity of carrying out electron-beam exposure with good reproducibility and the capability of more accurate control of the pillar sizes and shapes of the air-bridge. (C) 2007 Elsevier Ltd. All rights reserved.

Sterilization system for air purifier by combining ultraviolet light emitting diodes with TiO2

BACKGROUND: Ultraviolet light emitting diodes (UV LEDs) were used as a light source in TiO2 photocatalysis because of their many advantages, such as, long life, safety, low pollution, etc. In this experiment, a light source panel was successfully fabricated with UV LEDs, the light intensities of which were relatively uniform.

Determining of the delay time for a heating ventilating and air-conditioning plant using two weighted neural network approach

This paper presents an two weighted neural network approach to determine the delay time for a heating, ventilating and air-conditioning (HVAC) plan to respond to control actions. The two weighted neural network is a fully connected four-layer network. An acceleration technique was used to improve the General Delta Rule for the learning process. Experimental data for heating and cooling modes were used with both the two weighted neural network and a traditional mathematical method to determine the delay time. The results show that two weighted neural networks can be used effectively determining the delay time for AVAC systems.

Optical interleaver based on directional coupler in a 2D photonic crystal slab with triangular lattice of air holes

A small-size optical interleaver based on directional coupler in a 2D photonic crystal slab with triangular lattice of air holes is designed and theoretically simulated using plane wave expansion and finite-difference time-domain method. The interleaver is formed by two parallel and identical photonic crystal slab waveguides which are separated by three rows of air holes. The coupling region is designed below the light line to avoid vertical radiation. The simulated results show that the coupling coefficient is increased and the final length of the interleaver is decreased by enlarging the radius of the middle row of air holes. The transmission properties are analyzed after the interleaver's structure is optimized, and around 100 GHz channel spacing can be got when the length of the interleaver is chosen as 40.5 mu m. (c) 2006 Elsevier B.V. All rights reserved.

Determining of the delay time for a heating ventilating and air-conditioning plant using multi-weights neurons approach

This paper presents an multi weights neurons approach to determine the delay time for a Heating ventilating and air-conditioning (HVAC) plan to respond to control actions. The multi weights neurons is a fully connected four-layer network. An acceleration technique was used to improve the general delta rule for the learning process. Experimental data for heating and cooling modes were used with both the multi weights neurons and a traditional mathematical method to determine the delay time. The results show that multi weights neurons can be used effectively determining the delay time for HVAC systems.

Fabrication of metallic air bridges using multiple-dose electron beam lithography

The techniques of fabricating metallic air bridges using different resists in a one-step electron beam lithography are presented. The exposure process employed a single-layer polymethyl methacrylate (PMMA) or photoresists with either different doses in the span and feet areas or with varying acceleration voltage of the electron beam. The process using photoresists with different doses has produced air bridges more stable than what the PMMA method using various acceleration voltages would achieve. Using this method, air bridges up to 12 mu m long have been fabricated. The length and height of these metallic air bridges vary with the photoresist thickness. (c) 2006 American Institute of Physics.

Structure, fluorescence and stability of CdS nanoparticles prepared in air

CdS nanoparticies were prepared in air and their stability by air annealing was studied. A small change in crystal structure and particle size was observed by air annealing, but a rapid reduction in fluorescence was found. Through investigation, it is revealed that it is the surface change or reconstruction rather than the variation of the size or structure that decreases the fluorescence. The emission of the particles consists with two peaks which are dependent on the excitation energy. The two peaks are considered to be arisen from "two" different sizes of nanoparticles and may be explained in terms of selectively excited photoluminescence. Finally we discuss why the discrete state of nanoparticles are able to be resolved in the photoluminescence excitation spectrum, but could not be differentiated in the absorption spectrum.

High-power operation of quantum cascade lasers endured prolonged air-oxidation

High-power strain-compensated In1-xGaxAs/ln(1-y)Al(y)As quantum cascade lasers (lambda similar to 5.5 mu m) are demonstrated. Peak power at least 1.2W per facet for a 32 mu mx2mm uncoated laser stored in ambient condition for 240 days, is obtained at 80 K. Considering the collection efficiency of 60%, the actual output power is 4W at this temperature.

基于进化计算的无人飞行器多航迹规划

针对飞行器多航迹规划问题展开研究.在分析多峰值函数优化问题的基础上,提出了一种基于进化计算的飞行器多航迹规划方法.该方法通过使用特定的染色体表示方法和进化算子,可以有效利用各种环境信息,处理各种航迹约束.同时,通过引入聚类算法,将种群中的个体按其空间分布进行聚类,生成若干个不同子种群.在进化过程中,所有个体只在各自的子种群内部进化.当进化结束时,每个子种群将分别生成一条各自的最优航迹,从而为飞行器生成多条不同的可选航迹.仿真结果表明了该方法的有效性.