Random distributed feedback Raman fiber laser operating in a 1.2 μm wavelength range

The random distributed feedback fiber laser operating via the stimulated Raman scattering and random distributed feedback based on the Rayleigh scattering is demonstrated in the 1.2 μm frequency band. The RDFB fiber laser generates at 1174 nm up to 2.4 W of output power with corresponding slope efficiency more than 30%. The output radiation has the spectral shape similar to the conventional Raman fiber lasers and spectral width less than 1.7 nm. © 2011 Pleiades Publishing, Ltd.

Design and fabrication of two switched superconductivity microstrip hairpin filters using series micro-electro-mechanical systems (MEMS) switches

Series Micro-Electro-Mechanical System (MEMS) switches based on superconductor are utilized to switch between two bandpass hairpin filters with bandwidths of 365 MHz and nominal center frequencies of 2.1 GHz and 2.6 GHz. This was accomplished with 4 switches actuated in pairs, one pair at a time. When one pair was actuated the first bandpass filter was coupled to the input and output ports. When the other pair was actuated the second bandpass filter was coupled to the input and output ports. The device is made of a YBa2Cu 3O7 thin film deposited on a 20 mm x 20 mm LaAlO3 substrate by pulsed laser deposition. BaTiO3 deposited by RF magnetron sputtering in utilized as the insulation layer at the switching points of contact. These results obtained assured great performance showing a switchable device at 68 V with temperature of 40 K for the 2.1 GHz filter and 75 V with temperature of 30 K for the 2.6 GHz hairpin filter. ^

The relationship among serum levels of manganese superoxide dismutase and mitochondrial DNA 8-hydroxy-2'- deoxyguanosine, and dietary antioxidants intake in type 2 diabetes

Oxidative stress plays a key role in the development of Type 2 Diabetes (T2D). This cross-sectional study examined the relationship among serum levels of manganese superoxide dismutase (MnSOD), 8-hydroxy-2’-deoxyguanosine (8OHdG), dietary antioxidant intakes and glycemic control in African Americans (n=209) and Haitian Americans (n=234) with and without T2D. ^ African Americans had higher BMI (32.8 vs. 29.3 kg/m2), higher energy intake (2148 vs. 1770 kcal), and were more educated as compared to Haitian Americans; all variables were significant at p < .001. Serum levels of 8OHdG and MnSOD for African Americans (1691.0 ± 225.1 pg/ml, 2538.0 ± 1091.8 pg/ml; respectively) were significantly higher than for Haitian Americans (1626.2 ± 222.9, 2015.8 ± 656.3 pg/ml; respectively). 8OHdG was negatively correlated with MnSOD ( r = -.167, p < .001) in T2D. Having T2D was negatively correlated with MnSOD (r = -.337; p < .01) and positively correlated with 8OHdG (r = .500; p < .01). African Americans and Haitian Americans with T2D had fasting plasma glucose (FPG) levels of 143.0 ± 61.0 mg/dl and 157.6 ± 65.5 mg/dl, and A1C of 7.5 ± 1.8 % and 8.4 ± 2.4 %, respectively. African Americans and Haitian Americans without T2D had FPG levels of 95.8 ± 13.2 mg/dl and 98.7 ± 16.9 mg/dl, and A1C of 5.9 ± 0.4% and 6.0 ± 0.5%, respectively. Dietary intakes of vitamin C and vitamin D were negatively correlated with FPG (r = -.21; r = -.19, p < .05) respectively. Carotenoids negatively correlated with A1C (r = -.19, p < .05). Lower levels of MnSOD were associated with lower levels of zinc, r = .10, p < .05, and higher levels of carotenoids r = -.10, p < .05. Higher levels of 8OHdG were associated with lower levels of Vitamin D, r = -.14, p < .01, and carotenoids, r = -.09, p < .05. ^ The results demonstrate greater oxidative mtDNA damage in persons with T2D compared to those without T2D and in African Americans compared with Haitian Americans. The inverse relationship between dietary intake of antioxidants and oxidative stress implies a potential to reduce oxidative stress with diet. ^

Estudo da variação da periodicidade e do acoplamento entre superfícies seletivas de frequência com elementos fractais e helicoidais em estruturas de multicamadas

This work aims to investigate the behavior of fractal and helical elements structures in planar microstrip. In particular, the frequency selective surfaces (FSSs) had changed its conventional elements to fractal and helical formats. The dielectric substrate used was fiberglass (FR-4) and has a thickness of 1.5 mm, a relative permittivity 4.4 and tangent loss equal to 0.02. For FSSs, was adopting the Dürer’s fractal geometry and helical geometry. To make the measurements, we used two antennas horns in direct line of sight, connected by coaxial cable to the vector network analyzer. Some prototypes were select for built and measured. From preliminary results, it was aimed to find practical applications for structures from the cascading between them. For FSSs with Dürer’s fractal elements was observed behavior provided by the multiband fractal geometry, while the bandwidth has become narrow as the level of iteration fractal increased, making it a more selective frequency with a higher quality factor. A parametric analysis allowed the analysis of the variation of the air layer between them. The cascading between fractal elements structure were considered, presented a tri-band behavior for certain values of the layer of air between them, and find applications in the licensed 2.5GHz band (2.3-2.7) and 3.5GHz band (3.3-3.8). For FSSs with helical elements, six structures were considered, namely H0, H1, H2, H3, H4 and H5. The electromagnetic behavior of them was analyzed separately and cascaded. From preliminary results obtained from the separate analysis of structures, including the cascade, the higher the bandwidth, in that the thickness of the air layer increases. In order to find practical applications for helical structures cascaded, the helical elements structure has been cascaded find applications in the X-band (8.0-12.0) and unlicensed band (5.25-5.85). For numerical and experimental characterization of the structures discussed was used, respectively, the commercial software Ansoft Designer and a vector network analyzer, Agilent N5230A model.

Implementação de conversor de polarização linear-circular para antenas de microfita usando metasuperfícies

This work aims to propose a new model of metasurface with simplified basic cell, able to convert linearly polarized signals generated by planar antenna array in circularly polarized signals, for the ISM frequency band (2.45 GHz), with good bandwidth of return loss and axial ratio. To study the behavior of the proposed structure, the metasurface is coupled to three different structures. First, initial tests are made with the metasurface coupled to a microstrip antenna in its simple configuration. Then the metasurface is coupled to an array with two elements of patch type. And later it is coupled to an optimized array, that uses a stub in its main feed, to get a better impedance matching. The structures are analyzed numerically through Ansoft HFSS™, and to validate these results, the structures are characterized experimentally. The characteristics of transmissions simulated and measures are presented. A good agreement between simulated and measured results was obtained. The structure proposed here has the advantage of meeting the desired characteristics, with a simple geometry to be built using a low-cost substrate (FR-4).

Implementação de conversor de polarização linear-circular para antenas de microfita usando metasuperfícies

This work aims to propose a new model of metasurface with simplified basic cell, able to convert linearly polarized signals generated by planar antenna array in circularly polarized signals, for the ISM frequency band (2.45 GHz), with good bandwidth of return loss and axial ratio. To study the behavior of the proposed structure, the metasurface is coupled to three different structures. First, initial tests are made with the metasurface coupled to a microstrip antenna in its simple configuration. Then the metasurface is coupled to an array with two elements of patch type. And later it is coupled to an optimized array, that uses a stub in its main feed, to get a better impedance matching. The structures are analyzed numerically through Ansoft HFSS™, and to validate these results, the structures are characterized experimentally. The characteristics of transmissions simulated and measures are presented. A good agreement between simulated and measured results was obtained. The structure proposed here has the advantage of meeting the desired characteristics, with a simple geometry to be built using a low-cost substrate (FR-4).

TOC, TN, and sedimentary d15N and d13C ratios of sediment core SO201-2-85

We present high-resolution records of sedimentary nitrogen (d15Nbulk) and carbon isotope ratios (d13Cbulk) from piston core SO201-2-85KL located in the western Bering Sea. The records reflect changes in surface nitrate utilization and terrestrial organic matter contribution in submillennial resolution that span the last 180 kyr. The d15Nbulk record is characterized by a minimum during the penultimate interglacial indicating low nitrate utilization (~62-80%) despite the relatively high export production inferred from opal concentrations along with a significant reduction in the terrestrial organic matter fraction (mterr). This suggests that the consumption of the nitrate pool at our site was incomplete and even more reduced than today (~84%). d15Nbulk increases from Marine Isotope Stage (MIS) 5.4 and culminates during the Last Glacial Maximum, which indicates that nitrate utilization in the Bering Sea was raised during cold intervals (MIS 5.4, 5.2, 4) and almost complete during MIS 3 and 2 (~93-100%). This is in agreement with previous hypotheses suggesting that stronger glacial stratification reduced the nutrient supply from the subeuphotic zone, thereby increasing the iron-to-nutrient ratio and therefore the nitrate utilization in the mixed surface layer. Large variations in d15Nbulk were also recorded from 180 to 130 ka BP (MIS 6), indicating a potential link to insolation and sea-level forcing and its related feedbacks. Millennial-scale oscillations were observed in d15Nbulk and d13Cbulk that might be related to Greenland interstadials.

(Table 2) Age determination of sediment cores from the continental shelf of Mac Roberston Land, East Antarctica

Geochemical records are presented for five sediment cores from basins on the continental shelf of Mac. Robertson Land, East Antarctica. The cores contain 2-4 m thick sequences of hemipelagic, siliceous mud and ooze (SMO) deposited under seasonally open marine conditions. The inner and middle shelf SMO sequences are massive dark olive green material, whereas the outer shelf SMO sequences are dark olive material interspersed with light olive green layers ~1-10 cm thick. The biogenic material is dominated by marine diatoms including Fragilariopsis curta, Fragilariopsis cylindrus, and Chaetoceros spp. in the dark-colored SMO and Corethron criophilum in the light-colored layers. Radiocarbon dates suggest that the cores provide continuous accumulation records extending from < 1 kyr before present (B.P.) back as far as 4-15 kyr B.P., with estimated accumulation rates of 0.07-5 mm/yr. The three core records from the middle and outer shelf suggest six episodes of increased accumulation of biogenic material at ~5.5 kyr B.P. (all three cores), 1, 2, and 6.2 kyr B.P. (two of the three cores), and 3.8 and 10.8 kyr B.P. (one core), most of which coincide with Corethron layers. We interpret these features as the result of enhanced diatom production over the outer shelf, possibly related to climatic warm periods. The absence of such features in the inner shelf core records is thought to reflect a relatively constant level of seasonal diatom production in adjacent waters maintained by a coastal polynya.

Downwelling spectral irradiance as measured in different depths, remote sensing reflectance and phytoplankton pigment concentration during POLARSTERN cruises ANT-XXIV/1, ANT-XXIV/4, ANT-XXVI/4 and Maria S. Merian cruise MSM18/3

The composition and abundance of algal pigments provide information on phytoplankton community characteristics such as photoacclimation, overall biomass and taxonomic composition. In particular, pigments play a major role in photoprotection and in the light-driven part of photosynthesis. Most phytoplankton pigments can be measured by high-performance liquid chromatography (HPLC) techniques applied to filtered water samples. This method, as well as other laboratory analyses, is time consuming and therefore limits the number of samples that can be processed in a given time. In order to receive information on phytoplankton pigment composition with a higher temporal and spatial resolution, we have developed a method to assess pigment concentrations from continuous optical measurements. The method applies an empirical orthogonal function (EOF) analysis to remote-sensing reflectance data derived from ship-based hyperspectral underwater radiometry and from multispectral satellite data (using the Medium Resolution Imaging Spectrometer - MERIS - Polymer product developed by Steinmetz et al., 2011, doi:10.1364/OE.19.009783) measured in the Atlantic Ocean. Subsequently we developed multiple linear regression models with measured (collocated) pigment concentrations as the response variable and EOF loadings as predictor variables. The model results show that surface concentrations of a suite of pigments and pigment groups can be well predicted from the ship-based reflectance measurements, even when only a multispectral resolution is chosen (i.e., eight bands, similar to those used by MERIS). Based on the MERIS reflectance data, concentrations of total and monovinyl chlorophyll a and the groups of photoprotective and photosynthetic carotenoids can be predicted with high quality. As a demonstration of the utility of the approach, the fitted model based on satellite reflectance data as input was applied to 1 month of MERIS Polymer data to predict the concentration of those pigment groups for the whole eastern tropical Atlantic area. Bootstrapping explorations of cross-validation error indicate that the method can produce reliable predictions with relatively small data sets (e.g., < 50 collocated values of reflectance and pigment concentration). The method allows for the derivation of time series from continuous reflectance data of various pigment groups at various regions, which can be used to study variability and change of phytoplankton composition and photophysiology.

(Table 1) Details on the Uranium/Thorium age determinations carried out on core GeoB11569-2

Cold-water corals are widely distributed along the Atlantic continental margin with varying growth patterns in relation to their specific environment. Here, we investigate the long-term development of cold-water corals that once thrived on a low-latitude (17°40'N) cold-water coral mound in the Banda Mound Province off Mauritania during the last glacial-interglacial cycle. U/Th dates obtained from 20 specimens of the cold-water coral Lophelia pertusa, revealed three distinct periods of coral growth during the last glacial at 65 to 57 kyr BP, 45 to 32 kyr BP and 14 kyr BP, thus comprising the cool periods of Marine Isotopic Stages (MIS) 2-4. These coral growth periods occur during periods of increased productivity in the region, emphasizing that productivity seems to be the major steering factor for coral growth off Mauritania, which is one of the major upwelling regions in the world. This pattern differs from the well studied coral mounds off Ireland, where the current regime predominantly influences the prosperity of the cold-water corals. Moreover, coral growth off Ireland takes place during rather warm interglacial and interstadial periods, whereas off Mauritania coral growth is restricted to glacial and stadial periods. However, the on-mound sedimentation patterns off Mauritania largely resemble the observations reported from the Irish mounds. The bulk of the preserved sediments derives from periods of coral growth, whereas during periods without corals hardly any net sedimentation or mound growth took place.

Development of InAlN HEMTs for space application

This thesis investigates the emerging InAlN high electron mobility transistor (HEMT) technology with respect to its application in the space industry. The manufacturing processes and device performance of InAlN HEMTs were compared to AlGaN HEMTs, also produced as part of this work. RF gain up to 4 GHz was demonstrated in both InAlN and AlGaN HEMTs with gate lengths of 1 μm, with InAlN HEMTs generally showing higher channel currents (~150 c.f. 60 mA/mm) but also degraded leakage properties (~ 1 x 10-4 c.f. < 1 x 10-8 A/mm) with respect to AlGaN. An analysis of device reliability was undertaken using thermal stability, radiation hardness and off-state breakdown measurements. Both InAlN and AlGaN HEMTs showed excellent stability under space-like conditions, with electrical operation maintained after exposure to 9.2 Mrad of gamma radiation at a dose rate of 6.6 krad/hour over two months and after storage at 250°C for four weeks. Furthermore a link was established between the optimisation of device performance (RF gain, power handling capabilities and leakage properties) and reliability (radiation hardness, thermal stability and breakdown properties), particularly with respect to surface passivation. Following analysis of performance and reliability data, the InAlN HEMT device fabrication process was optimised by adjusting the metal Ohmic contact formation process (specifically metal stack thicknesses and anneal conditions) and surface passivation techniques (plasma power during dielectric layer deposition), based on an existing AlGaN HEMT process. This resulted in both a reduction of the contact resistivity to around 1 x 10-4 Ω.cm2 and the suppression of degrading trap-related effects, bringing the measured gate-lag close to zero. These discoveries fostered a greater understanding of the physical mechanisms involved in device operation and manufacture, which is elaborated upon in the final chapter.