Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

Implementation of WHO Quality Rights assessment in Kabul Mental Health Hospital

RESUMO: Objetivo Avaliar a qualidade dos serviços de saúde mental e a situação dos direitos humanos no Hospital de Saúde Mental de Kabul (KMHH) e fornecer recomendações para o desenvolvimento de um plano de melhoria, actualização e revisão da Política, Estratégia e Plano Nacionais de Saúde Mental,. Métodos A avaliação foi realizada em Janeiro de 2015 no KMHH e na Burn Ward do Hospital Terciário de Isteqlal por uma equipa multidisciplinar usando Qualidade Direitos Tool Kit da OMS. Antes da avaliação, o protocolo foi aprovado pelo Institutional Review Board e obtido o consentimento informado de cada entrevistado. Realizaram-se entrevistas com 16 utentes do serviço, 17 funcionários do hospital e 7 familiares, além da revisão de documentos e da observação das unidades de internamento do KMHH e das interações interpessoais entre funcionários do hospital e utentes do serviço. A comissão de avaliação reviu também a documentação e observou a Unidade de Queimados do Hospital Terciário de Isteqlal, a fim de avaliar e comparar a paridade entre as duas instalações. Após a avaliação, todos os membros da comissão se reuniram e puseram em conjunto todas as conclusões num relatório final. Resultados Encontrámos algumas lacunas graves no nível de prestação de serviços e no respeito pelos direitos humanos dos utentes dos serviços e dos seus familiares. Uma série de políticas, diretrizes e procedimentos relacionados com os direitos humanos dos pacientes estavam ausentes. O ambiente terapêutico e o padrão de vida eram inadequados, existia má qualidade do atendimento e dos serviços prestados, os utilizadores enfrentavam violações do direito ao exercício da capacidade legal e da liberdade pessoal, eram quimica e fisicamente (uso de correntes) contidos e expostos a abusos verbais, físicos e emocionais, e havia grande ênfase no tratamento institucional. Todos estes aspectos foram considerados como extensa violação dos direitos humanos dos utentes de serviço do KMHH. Conclusão Os serviços disponíveis para utentes dos serviços de saúde mental apresentam alguns problemas devido à desconfiança e falta de consciencialização sobre os direitos das pessoas com doença mental e precisam ser alterados de forma positiva. A Lei de Saúde Mental existente difere muito das recomendações da Convenção sobre os Direitos das Pessoas com Incapacidades (CRPD) e requer revisão e adaptação de acordo com esta Convenção. -------------------------------- ABSTRACT: Objective To assess the quality of mental health services and human rights condition in the Kabul Mental Health Hospital (KMHH) and provide recommendations for development of an improvement plan and to update and revise the National Mental Health Policy, Strategy and Plan. Methods The assessment was conducted in January 2015 in the KMHH and the Burn Ward of Isteqlal Tertiary Hospital by a multidisciplinary team using WHO Quality Rights Tool Kit. Before the assessment, Institutional Review Board approval and informed consent from each interviewee were obtained. Interviews were conducted with 16 service users, 17 hospital staffs and 7 family members in addition to documents review and observation of inpatient units of KMHH plus interpersonal interactions between hospital staff and service users. The assessment committee reviewed the documentation and observed the Burn Ward of Isteqlal Tertiary hospital in order to measure and compare parity between the two facilities. After the assessment, all committee members gathered and synchronized all findings into a final report. Results There were some serious gaps on service provision level and respecting human rights of service users and their family members. A series of policies, guidelines and procedures related to patients’ human rights were absent. Inadequate treatment environment and standard of living, poor quality of care and services, violations of the right to exercise legal capacity and personal liberty, being chemically and physically (e.g. chain) restrained, being exposed to verbal, physical and emotional abuse, and emphasis on institutional treatment were all extensive human rights violation that service users were experiencing in KMHH. Conclusion The available services for mental health service users are questionable due to mistrust and lack of awareness about rights of people with disabilities and need to be positively changed. Existing Mental Health Act has a large number of disparities with the CRPD and requires revision and adaptation in accordance to CRPD.

Crowdfunding campaigns: Perceived quality and success

Research in Crowdfunding is an emerging priority within the field of Entrepreneurship. Hundreds of platforms provide nowadays multiple Crowdfunding schemes which are intended to make it easier for entrepreneurs and others to collect money from the crowd. However, only a few campaigns become successful as others don’t reach the pre-established funding goal. It is thus necessary to keep on understanding the dynamics of these platforms and the factors which justify success. The asymmetry of information has been shown to be a delicate issue as people perceive quality in different manners. As so, this research aims to understand which components of perceived quality mostly influence investments decisions. Mainly Entrepreneurship and Marketing theories were explored along the way. This is research follows a causal approach where nineteen hypotheses are tested. An experimental survey was conducted and data was collected from 127 people who were asked to evaluate one of the most important pieces of any Crowdfunding campaign – the pitch video – and consequently invest on the presented products.

Semantic architecture for sensors

Based on the report for the unit “Sociology of New Information Technologies” of the Master on Computer Sciences at FCT/University Nova Lisbon in 2015-16. The responsible of this curricular unit is Prof. António Moniz

Product quality judgments in a two-sequence cue environment

Previous research demonstrated that the sequence of informational cues and the level of distraction have an impact on the judgment of a product’s quality. This study investigates the influence of the force behind the processing of these cues, working memory (WM). The results indicate that without distraction, consumers with low and high WM capacity (WMC) equally base their product evaluation on the first sequential cue. In the presence of a distractor, however, low WM individuals are no longer able to recall the initial cue, and thus derive their product judgment from the final cue. Moreover, evidence of intercultural differences in the perception of product related cues, and their aptitude for signaling a favorable product quality is provided.

Genetic algorithm for shipping route estimation with long-range tracking data : automatic reconstruction of shipping routes based on the historical ship positions for maritime safety applications

Ship tracking systems allow Maritime Organizations that are concerned with the Safety at Sea to obtain information on the current location and route of merchant vessels. Thanks to Space technology in recent years the geographical coverage of the ship tracking platforms has increased significantly, from radar based near-shore traffic monitoring towards a worldwide picture of the maritime traffic situation. The long-range tracking systems currently in operations allow the storage of ship position data over many years: a valuable source of knowledge about the shipping routes between different ocean regions. The outcome of this Master project is a software prototype for the estimation of the most operated shipping route between any two geographical locations. The analysis is based on the historical ship positions acquired with long-range tracking systems. The proposed approach makes use of a Genetic Algorithm applied on a training set of relevant ship positions extracted from the long-term storage tracking database of the European Maritime Safety Agency (EMSA). The analysis of some representative shipping routes is presented and the quality of the results and their operational applications are assessed by a Maritime Safety expert.

Proposta de um modelo de medição e análise da satisfação de clientes em empresas de software : caso prático do ambiente business-to-business

Os estudos da satisfação e lealdade do cliente em ambiente Business-to-Business têm emergido devido ao interesse práctico e académico. Recorreu-se a um caso práctico de uma empresa de software internacional, ESRI, a operar em Portugal com modelo de negócio B2B e comportamento de compra extensivo. Desenvolveu-se um modelo estrutural com 11 variáveis latentes: lealdade; satisfação; imagem; atmosfera; cooperação; adaptação; processos; tecnologia; orientação ao cliente; competências; colaboradores e comunicação. Foram analisadas 304 respostas ao questionário de satisfação e de seguida aplicou-se o modelo a seis grupos de clientes segmentados de acordo com a contribuição do cliente para as receitas e o comportamento no processo de decisão de compra. Recorreu-se a modelos SEM (Structural Equation Modelling) com estimação dos parâmetros através da metodologia PLS (partial Least Squares). Os resultados mostram nos seis segmentos, que os valores da empresa, a cooperação através da competência dos colaboradores e da orientação ao cliente e a tecnologia são factores mais importantes para a satisfação e lealdade dos clientes.

The impact of poor power quality in solar photovoltaic microgeneration: technical problems and losses of revenue

This paper presents a critical and quantitative analysis of the influence of the Power Quality in grid connected solar photovoltaic microgeneration installations. First are introduced the main regulations and legislation related with the solar photovoltaic microgeneration, in Portugal and Europe. Next are presented Power Quality monitoring results obtained from two residential solar photovoltaic installations located in the north of Portugal, and is explained how the Power Quality events affect the operation of these installations. Afterwards, it is described a methodology to estimate the energy production losses and the impact in the revenue caused by the abnormal operation of the electrical installation. This is done by comparing the amount of energy that was injected into the power grid with the theoretical value of energy that could be injected in normal conditions. The performed analysis shows that Power Quality severally affects the solar photovoltaic installations operation. The losses of revenue in the two monitored installations M1 and M2 are estimated in about 27% and 22%, respectively.

The influence of low-frequency noise pollution on the quality of life and place in sustainable cities: a case study from northern Portugal

Discussing urban planning requires rethinking sustainability in cities and building healthy environments. Historically, some aspects of advancing the urban way of life have not been considered important in city planning. This is particularly the case where technological advances have led to conflicting land use, as with the installation of power poles and building electrical substations near residential areas. This research aims to discuss and rethink sustainability in cities, focusing on the environmental impact of low-frequency noise and electromagnetic radiation on human health. It presents data from a case study in an urban space in northern Portugal, and focuses on four guiding questions: Can power poles and power lines cause noise? Do power poles and power lines cause discomfort? Do power poles and power lines cause discomfort due to noise? Can power poles and power lines affect human health? To answer these questions, we undertook research between 2014 and 2015 that was comprised of two approaches. The first approach consisted of evaluating the noise of nine points divided into two groups â near the sourceâ (e.g., up to 50 m from power poles) and â away from the sourceâ (e.g., more than 250 m away from the source). In the second approach, noise levels were measured for 72 h in houses located up to 20 m from the source. The groups consist of residents living within the distance range specified for each group. The measurement values were compared with the proposed criteria for assessing low-frequency noise using the DEFRA Guidance (University of Salford). In the first approach, the noise caused discomfort, regardless of the group. In the second approach, the noise had fluctuating characteristics, which led us to conclude that the noise caused discomfort.

Audit quality: does gender composition of audit firms matter?

Using a sample of Portuguese audit firms and their client companies, this study examines the association between gender composition of the partnership structure oaudit firms and audit quality. Audit quality is measured through the earnings quality of audit clients. We find that gender diversity in the partnership structure of audit firms, per se, has no association with audit quality. In turn, we find significant evidence that a predominant presence of female Certified Public Accountants (CPAs) in partner positions in audit firms is associated with higher audit quality. In particular, the results indicate that audit firms with female-dominated partnership structures are negatively related with aggressive accounting practices in audit clients.

HEP-Frame: A software engineered framework to aid the development and efficient multicore execution of scientific code

This work was supported by FCT (Fundação para a Ciência e Tecnologia) within Project Scope (UID/CEC/00319/2013), by LIP (Laboratório de Instrumentação e Física Experimental de Partículas) and by Project Search-ON2 (NORTE-07-0162- FEDER-000086), co-funded by the North Portugal Regional Operational Programme (ON.2 - O Novo Norte), under the National Strategic Reference Framework, through the European Regional Development Fund.

Thermal conditions affecting heat transfer in FDM/FFE: a contribution towards the numerical modelling of the process

The performance of parts produced by Free Form Extrusion (FFE), an increasingly popular additive manufacturing technique, depends mainly on their dimensional accuracy, surface quality and mechanical performance. These attributes are strongly influenced by the evolution of the filament temperature and deformation during deposition and solidification. Consequently, the availability of adequate process modelling software would offer a powerful tool to support efficient process set-up and optimisation. This work examines the contribution to the overall heat transfer of various thermal phenomena developing during the manufacturing sequence, including convection and radiation with the environment, conduction with support and between adjacent filaments, radiation between adjacent filaments and convection with entrapped air. The magnitude of the mechanical deformation is also studied. Once this exercise is completed, it is possible to select the material properties, process variables and thermal phenomena that should be taken in for effective numerical modelling of FFE.

Pervasive business intelligence platform to improve the quality of decision process in primary and secondary education – A Portuguese case study

Business Intelligence (BI) can be seen as a method that gathers information and data from information systems in order to help companies to be more accurate in their decision-making process. Traditionally BI systems were associated with the use of Data Warehouses (DW). The prime purpose of DW is to serve as a repository that stores all the relevant information required for making the correct decision. The necessity to integrate streaming data became crucial with the need to improve the efficiency and effectiveness of the decision process. In primary and secondary education, there is a lack of BI solutions. Due to the schools reality the main purpose of this study is to provide a Pervasive BI solution able to monitoring the schools and student data anywhere and anytime in real-time as well as disseminating the information through ubiquitous devices. The first task consisted in gathering data regarding the different choices made by the student since his enrolment in a certain school year until the end of it. Thereafter a dimensional model was developed in order to be possible building a BI platform. This paper presents the dimensional model, a set of pre-defined indicators, the Pervasive Business Intelligence characteristics and the prototype designed. The main contribution of this study was to offer to the schools a tool that could help them to make accurate decisions in real-time. Data dissemination was achieved through a localized application that can be accessed anywhere and anytime.

Algorithms and tools for in silico design of cell factories

PhD thesis in Bioengineering

Refinement and variability techniques in model transformation of software requirements

Tese de Doutoramento em Tecnologias e Sistemas de Informação