Doubly fed induction generator versus direct drive permanent magnet synchronous generator in wind power applications

The objective of this master's thesis is to compare two different generator systems for wind turbines. It is the doubly fed induction generator system with three stage gearbox and the direct drive permanent magnet generator system. The comparison of generator systems is based on annual energy production for a given wind climate. For comparison a 3 MW, 15 rpm wind turbine is used. Modelling of a turbine rotor, gearbox and converters were done. Design of two generators was done and their performance was examined.

Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

Analysis and Control of Excitation, Field Weakening and Stability in Direct Torque Controlled Electrically Excited Synchronous Motor Drives

Direct torque control (DTC) is a new control method for rotating field electrical machines. DTC controls directly the motor stator flux linkage with the stator voltage, and no stator current controllers are used. With the DTC method very good torque dynamics can be achieved. Until now, DTC has been applied to asynchronous motor drives. The purpose of this work is to analyse the applicability of DTC to electrically excited synchronous motor drives. Compared with asynchronous motor drives, electrically excited synchronous motor drives require an additional control for the rotor field current. The field current control is called excitation control in this study. The dependence of the static and dynamic performance of DTC synchronous motor drives on the excitation control has been analysed and a straightforward excitation control method has been developed and tested. In the field weakening range the stator flux linkage modulus must be reduced in order to keep the electro motive force of the synchronous motor smaller than the stator voltage and in order to maintain a sufficient voltage reserve. The dynamic performance of the DTC synchronous motor drive depends on the stator flux linkage modulus. Another important factor for the dynamic performance in the field weakening range is the excitation control. The field weakening analysis considers both dependencies. A modified excitation control method, which maximises the dynamic performance in the field weakening range, has been developed. In synchronous motor drives the load angle must be kept in a stabile working area in order to avoid loss of synchronism. The traditional vector control methods allow to adjust the load angle of the synchronous motor directly by the stator current control. In the DTC synchronous motor drive the load angle is not a directly controllable variable, but it is formed freely according to the motor’s electromagnetic state and load. The load angle can be limited indirectly by limiting the torque reference. This method is however parameter sensitive and requires a safety margin between the theoretical torque maximum and the actual torque limit. The DTC modulation principle allows however a direct load angle adjustment without any current control. In this work a direct load angle control method has been developed. The method keeps the drive stabile and allows the maximal utilisation of the drive without a safety margin in the torque limitation.

First-Line Chemotherapy with Anthracycline and Taxane Combination in Metastatic Breast Cancer. Detection of bone metastases with TRACP 5b

Background: In Finland, breast cancer (BC) is the most common cancer among women, and prostate cancer (PC) that among men. At the metastatic stage both cancers remain essentially incurable. The goals of therapy include palliation of symptoms, improvement or maintenance of quality of life (QoL), delay of disease progression, and prolongation of survival. Balancing between efficacy and toxicity is the major challenge. With increasing costs of new treatments, appropriate use of resources is paramount. When new treatment regimes are introduced into clinical practice a comprehensive assessment of clinical benefit, adverse effects and cost is necessary. Both BC and PC show a predilection to metastasize to bone. Bone metastases cause significant morbidity impairing the patients´ QoL. Diagnosis of bone metastases relies mainly on radiological methods, which however lack optimal sensitivity and specificity. New tools are needed for detection and follow-up of bone metastases. Aims: Anthracyclines and taxanes are effective chemotherapeutic agents in the treatment of metastatic breast cancer (MBC) with different mechanisms of action. Therefore, evaluation of the combination of anthracyclines with taxanes was a justifiable approach in the treatment of MBC patients. We assessed the efficacy, toxicity, cost of treatment and QoL of BC patients treated with first-line chemotherapy for metastatic disease with the combination epirubicin and docetaxel. We also evaluated the diagnostic potential of tartrate-resistant acid phosphatase 5b (TRACP 5b) and carboxyterminal telopeptides of type I collagen (ICTP) in the diagnosis of bone metastases in BC and TRACP 5b in PC patients. Results: The combination of epirubicin and docetaxel was effective in this phase II study, but required individual dose adjustment to avoid neutropenic infections, and the use of growth factors to maintain a feasible dose level. The response rate was 54 % (95 % CI 37-71) and the median overall survival (OS) was 26 months. Of the patients, 87 % were treated for infections. The treatment of adverse events required additional use of health resources mainly due to neutropenic infections, thereby raising direct treatment costs by 20 %. Despite adverse events, the global QoL was not significantly compromised during the treatment. Clinically evident acute cardiac toxicity was not observed. The combination of serum TRACP 5b and ICTP was at least equally sensitive and specific in detection of of bone metastases as commonly used total alkaline phosphatise (tALP) in BC patients. In contrast, TRACP 5b was less specific and sensitive than tALP as a marker of skeletal changes in PC patients. Conclusions: Treatment with epirubicin and docetaxel showed high efficacy in first-line chemotherapy of MBC. The relatively high incidence of neutropenic infections requiring hospitalization increased the treatment costs. Despite adverse events, the global QoL of the patients was not significantly compromised. The combination of TRACP 5b and ICTP showed similar activity as tALP in detecting bone metastases in MBC. In contrast, TRACP 5b was less specific and sensitive than tALP as a marker of skeletal changes in PC.

Costs and Benefits of a Shared Digital Long-Term Preservation System

Paper presented at the 40th Annual Conference of LIBER (Ligue des Bibliothèques Européennes de Recherche - Association of European Research Libraries) on July 1st, 2011; with the slides used at the presentation.

Kiinteistön elinkaarihankkeen rahoitus ja riskit

Julkisen sektorin kiinteistötuotannossa toteutetaan kasvavassa määrin julkisen ja yksityisen sektorin yhteistyötä, jossa yksityinen yritys ottaa vastuun kiinteistöön liittyvistä suunnittelu-, rakentamis- ja ylläpitotoimista pitkäksi ajanjaksoksi. Työn tavoitteena on arvioida elinkaarimallilla toteuttavien kiinteistöhankkeiden toteutusvaihtoehdot, sekä kartoittaa elinkaarihankkeen sisältämiä riskejä hankkeen suunnitteluvaiheessa. Tutkimus suoritetaan kvalitatiivisena tutkimuksena, jota tuetaan tarvittavilla kvantitatiivista tietoa hyödyntävillä laskelmilla. Tutkimusaineistona käytetään aihepiiriin liittyviä akateemisia julkaisuja ja oppikirjoja. Työn toimeksiantajan YIT:n kautta tutkimukseen on saatu arvokasta asiantuntemusta ja materiaalia. Elinkaarihankkeiden hankintamenettelyksi suositellaan kilpailullista neuvottelumenettelyä. Kilpailullinen neuvottelumenettely mahdollistaa tilaajan ja palveluntuottajien välisen dialogin hankintamenettelyn aikana, jolloin osapuolet voivat yhteistyössä valita sopivimman toteutusmallin. Hankkeiden rahoitus voidaan toteuttaa tilaajan rahoituksella tai yksityisrahoituksella. Rahoituksen näkökulmasta tilaajan oma rahoitus on edullisin, mikä ei kuitenkaan vähennä elinkaarimallista saatavia etuja perinteiseen urakointiin verrattuna. Laskelman perusteella tilaajan rahoituksen ja yksityisrahoituksen keskimääräisessä korkotasossa (WACC) on eroa 2,8 %. Projektiyhtiön perustaminen tekee rahoituksesta entistä kalliimpaa, koska taseeseen kohdistuviin kustannuksiin lisätään projektiyhtiön oman pääoman tuottovaatimusta vastaava korko. Palveluntuottajan kannalta olennaiset riskit ovat rakennusvaiheen viivästyminen, kiinteistön käytettävyyden ja soveltuvuuden puutteista aiheutuvat muutostyöt. Palvelumaksun sitominen huonosti ylläpidon todellista kulurakennetta kuvaavaan elinkustannusindeksiin tulee pitkällä sopimuskaudella vähentämään palveluntuottajan toiminnan kannattavuutta. Kiinteistön ylläpidon kustannusindeksi on vuosina 2005–2011 noussut 2,3 % nopeammin vuodessa kuin elinkustannusindeksi.

Costs and Benefits of a Shared Digital Long-Term Preservation System

This paper describes the cost-benefit analysis of digital long-term preservation (LTP) that was carried out in the context of the Finnish National Digital Library Project (NDL) in 2010. The analysis was based on the assumption that as many as 200 archives, libraries, and museums will share an LTP system. The term ‘system’ shall be understood as encompassing not only information technology, but also human resources, organizational structures, policies and funding mechanisms. The cost analysis shows that an LTP system will incur, over the first 12 years, cumulative costs of €42 million, i.e. an average of €3.5 million per annum. Human resources and investments in information technology are the major cost factors. After the initial stages, the analysis predicts annual costs of circa €4 million. The analysis compared scenarios with and without a shared LTP system. The results indicate that a shared system will have remarkable benefits. At the development and implementation stages, a shared system shows an advantage of €30 million against the alternative scenario consisting of five independent LTP solutions. During the later stages, the advantage is estimated at €10 million per annum. The cumulative cost benefit over the first 12 years would amount to circa €100 million.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

CLONAL PROPAGATION OF NEEM (Azadirachta indica A. Juss.) VIA DIRECT AND INDIRECT IN VITRO REGENERATION

ABSTRACTThe study was conducted with shoot tip explants of neem (Azadirachta indica A. Juss) to identify a viable regenerative process. Shoot tips were obtained from neem embryos cultured alternatingly in DKW medium supplemented with BAP and medium without hormones. Initial shoot development was influenced by cotyledon presence. Basal callus, excised from in vitro stem base, also presented organogenic potential. In some cases, plant lines, obtained from each seed, presented different characteristics. The most common characteristic observed in vitro was callus formation at the stem base. However, the rarest characteristics were stem callus formation and leaf senescence. The regenerated shoot tips were further subculture and rooted on a medium supplemented with IBA so that complete plants could be obtained. The rooted plants were transplanted to a greenhouse and successfully acclimatized. No significant differences in in vivo development were observed between neem plants from callus and from shoot tip propagation.

CFD Modelling of Direct Contact Condensation in Suppression Pools by Applying Condensation Models of Separated Flow

The condensation rate has to be high in the safety pressure suppression pool systems of Boiling Water Reactors (BWR) in order to fulfill their safety function. The phenomena due to such a high direct contact condensation (DCC) rate turn out to be very challenging to be analysed either with experiments or numerical simulations. In this thesis, the suppression pool experiments carried out in the POOLEX facility of Lappeenranta University of Technology were simulated. Two different condensation modes were modelled by using the 2-phase CFD codes NEPTUNE CFD and TransAT. The DCC models applied were the typical ones to be used for separated flows in channels, and their applicability to the rapidly condensing flow in the condensation pool context had not been tested earlier. A low Reynolds number case was the first to be simulated. The POOLEX experiment STB-31 was operated near the conditions between the ’quasi-steady oscillatory interface condensation’ mode and the ’condensation within the blowdown pipe’ mode. The condensation models of Lakehal et al. and Coste & Lavi´eville predicted the condensation rate quite accurately, while the other tested ones overestimated it. It was possible to get the direct phase change solution to settle near to the measured values, but a very high resolution of calculation grid was needed. Secondly, a high Reynolds number case corresponding to the ’chugging’ mode was simulated. The POOLEX experiment STB-28 was chosen, because various standard and highspeed video samples of bubbles were recorded during it. In order to extract numerical information from the video material, a pattern recognition procedure was programmed. The bubble size distributions and the frequencies of chugging were calculated with this procedure. With the statistical data of the bubble sizes and temporal data of the bubble/jet appearance, it was possible to compare the condensation rates between the experiment and the CFD simulations. In the chugging simulations, a spherically curvilinear calculation grid at the blowdown pipe exit improved the convergence and decreased the required cell count. The compressible flow solver with complete steam-tables was beneficial for the numerical success of the simulations. The Hughes-Duffey model and, to some extent, the Coste & Lavi´eville model produced realistic chugging behavior. The initial level of the steam/water interface was an important factor to determine the initiation of the chugging. If the interface was initialized with a water level high enough inside the blowdown pipe, the vigorous penetration of a water plug into the pool created a turbulent wake which invoked the chugging that was self-sustaining. A 3D simulation with a suitable DCC model produced qualitatively very realistic shapes of the chugging bubbles and jets. The comparative FFT analysis of the bubble size data and the pool bottom pressure data gave useful information to distinguish the eigenmodes of chugging, bubbling, and pool structure oscillations.

Perfomance evaluation of a direct injection engine using different blends of soybean (Glycine max) methyl biodiesel

Diesel fuel is used widely in Brazil and worldwide. On the other hand, the growing environmental awareness leads to a greater demand for renewable energy resources. Thus, this study aimed to evaluate the use of different blends of soybean (Glycine max) methyl biodiesel and diesel in an ignition compression engine with direct injection fuel. The tests were performed on an electric eddy current dynamometer, using the blends B10, B50 and B100, with 10; 50 e 100% of biodiesel, respectively, in comparison to the commercial diesel B5, with 5% of biodiesel added to the fossil diesel. The engine performance was analyzed trough the tractor power take off (PTO) for each fuel, and the best results obtained for the power and the specific fuel consumption, respectively, were: B5 (44.62 kW; 234.87 g kW-1 h-1); B10 (44.73 kW; 233.78 g kW-1 h-1); B50 (44.11 kW; 250.40 g kW-1 h-1) e B100 (43.40 kW; 263.63 g kW-1 h-1). The best performance occurred with the use of B5 and B10 fuel, without significant differences between these blends. The B100 fuel showed significant differences compared to the other fuels.

Annual evolution of global, direct and diffuse radiation and fractions in tilted surfaces

It was evaluated the annual evolution of global, direct and diffuse components of incident solar radiation on tilted surfaces to 12.85, 22.85 and 32.85º, facing north, in Botucatu, state of São Paulo, Brazil. The radiometric fractions were obtained for each component of the radiation in the aforementioned surfaces, through the ratio with the global and top of the atmosphere radiations. Seasonality was evaluated based on monthly averages of daily values. The measures occurred between 04/1998 and 07/2001 at 22.85º; 08/2001 and 02/2003 at 12.85º; and from 03/2003 to 12/2007 at 32.85º, with concomitant measures in the horizontal surface (reference). The levels of global and direct radiation on tilted surfaces were lower in summer and higher in the equinoxes when compared with the horizontal. The diffuse radiation on tilted surfaces was lower in most months, with losses of up to 65%. A trend of increasing differences occurred between horizontal and tilted surfaces with the increase of the angle in all the components and fractions of incident radiation. The annual evolution of rainfall and cloud cover ratio directly affected the atmospheric transmissivity of direct and diffuse components in the region.

Hevonen irtaimen kaupan tapauksena - laatuvirhe ja siihen varautuminen

Tutkimuksessa tarkastellaan hevoskauppaa ja sen erityispiirteitä suhtees-sa irtaimen kauppaa säätelevään lainsäädäntöön. Tavoitteena on tuoda esiin hevosesta johtuvia erityispiirteitä ja pohtia sovellettavan lainsäädän-nön soveltuvuutta hevosen kauppaan. Tarkastelu kohdentuu erityisesti hevoselle ominaisiin laatuvirheen muotoihin, kuten sairauksiin ja fyysisiin vikoihin. Lisäksi tarkastellaan, miten esiin nostettuihin erityispiirteisiin on varauduttu hevoskauppaan tarkoitetuissa kauppasopimusmalleissa. Hevoskauppaan pätee sama lainsäädäntö kuin minkä tahansa muun ir-taimen tavaran kauppaan. Virheeseen varautuminen yksityiskohtaisesti sopimalla korostuu hevoskaupassa, koska täydellistä ja virheetöntä hevosta ei ole olemassakaan. Myyjän näkökulmasta onnistuneessa kauppaprosessissa neuvotellaan virheen mahdollisuus niin pieneksi kuin se on mahdollista. Tähän instrumentit antavat lainsäädäntö ja erityisesti sopimusoikeudelliset keinot. Ostajan näkökulmasta onnistuneessa kaupassa hän on kyennyt asiantuntijoihin tukeutuen tunnistamaan ennalta hevosen viat ja muut epämieluisat ominaisuudet. Nämä tiedostaen ostaja määrittää, mitä virheitä on valmis hyväksymään. Hevoskaupassa riidan välittömät ja välilliset kustannukset suhteessa maksettuun kauppahintaan voivat nousta korkeiksi. Hevoskaupassa usein ainoa kirjallinen dokumentti on omistajanvaihdosilmoitus, eikä kauppasopimuksen laatiminen kirjallisena ole itsestäänselvyys. Yksinomaan hevoskauppaan liittyvien juridisten kysymysten tekeminen näkyväksi on tärkeää. Irtaimen kauppaa säätelevä lainsäädäntö ei kuitenkaan tunnista riittävällä tarkkuudella hevosen erityispiirteitä persoonaesineenä, vaan väliin tarvi-taan vakiosopimusten kaltaisia apuvälineitä kaupan osapuolten tueksi.

Marketing-Sales Cooperation and its Relation on Direct Sales Performance: an Example of a Medium-sized Oil Company

The study touches upon marketing-sales departments’ cooperation and investigates marketing-sales cooperative model within the case company. So that research increases understanding of linkages between Marketing and Sales departments with an illustrative example of Russian medium-sized oil company (LLC Neste St. Petersburg), the subsidiary of Finnish-based Neste Oil. The empirical study is done from marketing and sales perspectives. And for sales main attention was brought to direct sales, both B2B and B2C. Research considers all five domains of cooperation, and among others, study reveals the attitude towards external (market) and internal (product) knowledge, and its mutual use by marketing and sales managers. A qualitative research method, participant observations, and in-depth interviews with upper-management made it possible to explore all facets of joint work. Moreover, research responses the changes in a model of cooperation between marketing and sales when moving from medium size to large company.