Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Making Sense of Shared Leadership. A case study of leadership processes and practices without formal leadership structure in the team context

Leadership is essential for the effectiveness of the teams and organizations they are part of. The challenges facing organizations today require an exhaustive review of the strategic role of leadership. In this context, it is necessary to explore new types of leadership capable of providing an effective response to new needs. The presentday situations, characterized by complexity and ambiguity, make it difficult for an external leader to perform all leadership functions successfully. Likewise, knowledge-based work requires providing professional groups with sufficient autonomy to perform leadership functions. This study focuses on shared leadership in the team context. Shared leadership is seen as an emergent team property resulting from the distribution of leadership influence across multiple team members. Shared leadership entails sharing power and influence broadly among the team members rather than centralizing it in the hands of a single individual who acts in the clear role of a leader. By identifying the team itself as a key source of influence, this study points to the relational nature of leadership as a social construct where leadership is seen as social process of relating processes that are co-constructed by several team members. Based on recent theoretical developments concerned with relational, practice-based and constructionist approaches to the study of leadership processes, this thesis proposes the study of leadership interactions, working processes and practices to focus on the construction of direction, alignment and commitment. During the research process, critical events, activities, working processes and practices of a case team have been examined and analyzed with the grounded theory –approach in the terms of shared leadership. There are a variety of components to this complex process and a multitude of factors that may influence the development of shared leadership. The study suggests that the development process of shared leadership is a common sense -making process and consists of four overlapping dimensions (individual, social, structural, and developmental) to work with as a team. For shared leadership to emerge, the members of the team must offer leadership services, and the team as a whole must be willing to rely on leadership by multiple team members. For these individual and collective behaviors to occur, the team members must believe that offering influence to and accepting it from fellow team members are welcome and constructive actions. Leadership emerges when people with differing world views use dialogue and collaborative learning to create spaces where a shared common purpose can be achieved while a diversity of perspectives is preserved and valued. This study also suggests that this process can be supported by different kinds of meaning-making and process tools. Leadership, then, does not reside in a person or in a role, but in the social system. The built framework integrates the different dimensions of shared leadership and describes their relationships. This way, the findings of this study can be seen as a contribution to the understanding of what constitutes essential aspects of shared leadership in the team context that can be of theoretical value in terms of advancing the adoption and development process of shared leadership. In the real world, teams and organizations can create conditions to foster and facilitate the process. We should encourage leaders and team members to approach leadership as a collective effort that the team can be prepared for, so that the response is rapid and efficient.

On the impact of rigorous approaches on the quality of development

Software systems are expanding and becoming increasingly present in everyday activities. The constantly evolving society demands that they deliver more functionality, are easy to use and work as expected. All these challenges increase the size and complexity of a system. People may not be aware of a presence of a software system, until it malfunctions or even fails to perform. The concept of being able to depend on the software is particularly significant when it comes to the critical systems. At this point quality of a system is regarded as an essential issue, since any deficiencies may lead to considerable money loss or life endangerment. Traditional development methods may not ensure a sufficiently high level of quality. Formal methods, on the other hand, allow us to achieve a high level of rigour and can be applied to develop a complete system or only a critical part of it. Such techniques, applied during system development starting at early design stages, increase the likelihood of obtaining a system that works as required. However, formal methods are sometimes considered difficult to utilise in traditional developments. Therefore, it is important to make them more accessible and reduce the gap between the formal and traditional development methods. This thesis explores the usability of rigorous approaches by giving an insight into formal designs with the use of graphical notation. The understandability of formal modelling is increased due to a compact representation of the development and related design decisions. The central objective of the thesis is to investigate the impact that rigorous approaches have on quality of developments. This means that it is necessary to establish certain techniques for evaluation of rigorous developments. Since we are studying various development settings and methods, specific measurement plans and a set of metrics need to be created for each setting. Our goal is to provide methods for collecting data and record evidence of the applicability of rigorous approaches. This would support the organisations in making decisions about integration of formal methods into their development processes. It is important to control the software development, especially in its initial stages. Therefore, we focus on the specification and modelling phases, as well as related artefacts, e.g. models. These have significant influence on the quality of a final system. Since application of formal methods may increase the complexity of a system, it may impact its maintainability, and thus quality. Our goal is to leverage quality of a system via metrics and measurements, as well as generic refinement patterns, which are applied to a model and a specification. We argue that they can facilitate the process of creating software systems, by e.g. controlling complexity and providing the modelling guidelines. Moreover, we find them as additional mechanisms for quality control and improvement, also for rigorous approaches. The main contribution of this thesis is to provide the metrics and measurements that help in assessing the impact of rigorous approaches on developments. We establish the techniques for the evaluation of certain aspects of quality, which are based on structural, syntactical and process related characteristics of an early-stage development artefacts, i.e. specifications and models. The presented approaches are applied to various case studies. The results of the investigation are juxtaposed with the perception of domain experts. It is our aspiration to promote measurements as an indispensable part of quality control process and a strategy towards the quality improvement.

Mental Well-being at Work. A Sign of a Healthy Organisation and a Necessary Precondition for Organisational Development

One of the aims of the study was to clarify the reliability and validity of the Job Diagnostic Survey (JDS) and the Eigenzustand (EZ) method as measures of the objective characteristics of work and short-term mental work load in the Finnish data. The reliability and validity were examined taking into consideration the theoretical backgrounds of the methods and the reliability of the measurements. The methods were used for finding out the preconditions for organisational development based on self-improvement and clarifying the impacts of working environment (organisational functioning and job characteristics) on a worker’s mental state and health. The influences were examined on a general level - regardless of individual personal or specific contextual factors. One aim was also to clarify how cognitions and emotions are intertwined and how they influence a person’s perception of the working environment. The data consisted of 15 blue-collar organisations in the public sector. The organisations were divided in target and comparison groups depending on the research frames. The data was collected by questionnaires by post. The exploratory and confirmatory factor analyses (Lisrel) were used as the main statistical methods in examining the structures of the methods and impacts between the variables. It was shown that it is possible for organisations to develop their working conditions themselves on specific preconditions. The advance of the development processes could be shown by the amount of the development activity as well as by the changes of the mental well-being (ability to act) and sick absenteeism of the personnel. It was found that the JDS and the EZ methods were reliable and valid measures in the Finnish data. It was shown that, in addition to the objective working environment (organisational functioning and job characteristics), also such a personal factor as selfesteem influences a person’s perception of mental work load. However, the influence did not seem to be direct. The importance of job satisfaction as a general indicator of perceived working conditions was emphasised. Emotional and cognitive factors were found to be functionally intertwined constituting a common factor. Organisational functioning and the characteristics of work had connections with a person’s health measured by sick absenteeism.

Eating disorders, weight perception, and dieting in adolescence

Background: Eating disorders are serious psychiatric disorders, which usually have their onset in adolescence. Body dissatisfaction and dieting, both common among adolescents, are recognised risk factors for eating disorders. The aim of the present study was to assess the prevalence of eating disorders in the general adolescent population, assess the risk of developing eating disorders in subgroups of dieters, and analyse longitudinal concomitants of incorrect weight perception. Method: A prospective follow-up study on 595 adolescents, aged 15 at baseline, was conducted in western Finland. The study comprised questionnaires directed at the whole study population and subsequent personal interviews with adolescents found to be screen-positive for eating disorders, at both baseline and three-year follow-up. Results: The lifetime prevalence rates for 18 year old females were 2.6 % for anorexia nervosa, 0.4 for bulimia nervosa, and 9.0 % for eating disorder not otherwise specified (EDNOS). No prevalent case of DSM-IV eating disorders was found among the male participants. Eating disorders, as well as depressive symptoms, social anxiety, and low self-esteem, was more prevalent among females who perceived themselves as being overweight, despite being normal or underweight, when compared to females with a correct weight perception. An incorrect weight perception was associated in males with social anxiety. Female adolescents dieting due to psychological distress, rather than vanity or overweight, had a fifteen-fold risk of developing an eating disorder. Conclusions: Eating disorders are common among female adolescents, and adolescents choosing to diet due to psychological distress show a markedly increased risk of developing an eating disorder. Promotion of general well-being as well as the prevention of body dissatisfaction and misdirected dieting, accompanied by early detection and proper treatment of eating disorders, is needed to reduce the incidence of and facilitate recovery in adolescents suffering from eating disorders.

Simulation of Solid Processes by Aspen Plus

Solid processes are used for obtaining the valuable minerals. Due to their worth, it is obligatory to perform different experiments to determine the different values of these minerals. With the passage of time, it is becoming more difficult to carry out these experiments for each mineral for different characteristics due to high labor costs and consumption of time. Therefore, scientists and engineers have tried to overcome this issue. They made different software to handle this problem. Aspen is one of those software for the calculation of different parameters. Therefore, the aim of this report was to do simulation for solid processes to observe different effect for minerals. Different solid processes like crushing, screening; filtration and crystallization were simulated by Aspen Plus. The simulation results are obtained by using this simulation software and they are described in this thesis. It was noticed that the results were acceptable for all solid processes. Therefore, this software can be used for the designing of crushers by calculating the power consumption of crushers, can design the filter and for the calculation of material balance for all processes.

“IT’S ALL RIGHT”. Multimodal rightward spatial bias modified by age and praxis

The general goal of the present work was to study whether spatial perceptual asymmetry initially observed in linguistic dichotic listening studies is related to the linguistic nature of the stimuli and/or is modality-specific, as well as to investigate whether the spatial perceptual/attentional asymmetry changes as a function of age and sensory deficit via praxis. Several dichotic listening studies with linguistic stimuli have shown that the inherent perceptual right ear advantage (REA), which presumably results from the left lateralized linguistic functions (bottom-up processes), can be modified with executive functions (top-down control). Executive functions mature slowly during childhood, are well developed in adulthood, and decline as a function of ageing. In Study I, the purpose was to investigate with a cross-sectional experiment from a lifespan perspective the age-related changes in top-down control of REA for linguistic stimuli in dichotic listening with a forced-attention paradigm (DL). In Study II, the aim was to determine whether the REA is linguistic-stimulus-specific or not, and whether the lifespan changes in perceptual asymmetry observed in dichotic listening would exist also in auditory spatial attention tasks that put load on attentional control. In Study III, using visual spatial attention tasks, mimicking the auditory tasks applied in Study II, it was investigated whether or not the stimulus-non-specific rightward spatial bias found in auditory modality is a multimodal phenomenon. Finally, as it has been suggested that the absence of visual input in blind participants leads to improved auditory spatial perceptual and cognitive skills, the aim in Study IV was to determine, whether blindness modifies the ear advantage in DL. Altogether 180-190 right-handed participants between 5 and 79 years of age were studied in Studies I to III, and in Study IV the performance of 14 blind individuals was compared with that of 129 normally sighted individuals. The results showed that only rightward spatial bias was observed in tasks with intensive attentional load, independent of the type of stimuli (linguistic vs. non-linguistic) or the modality (auditory vs. visual). This multimodal rightward spatial bias probably results from a complex interaction of asymmetrical perceptual, attentional, and/or motor mechanisms. Most importantly, the strength of the rightward spatial bias changed as a function of age and augmented praxis due to sensory deficit. The efficiency of the performance in spatial attention tasks and the ability to overcome the rightward spatial bias increased during childhood, was at its best in young adulthood, and decreased as a function of ageing. Between the ages of 5 and 11 years probably at first develops movement and impulse control, followed by the gradual development of abilities to inhibit distractions and disengage attention. The errors especially in bilateral stimulus conditions suggest that a mild phenomenon resembling extinction can be observed throughout the lifespan, but especially the ability to distribute attention to multiple targets simultaneously decreases in the course of ageing. Blindness enhances the processing of auditory bilateral linguistic stimuli, the ability to overcome a stimulus-driven laterality effect related to speech sound perception, and the ability to direct attention to an appropriate spatial location. It was concluded that the ability to voluntarily suppress and inhibit the multimodal rightward spatial bias changes as a function of age and praxis due to sensory deficit and probably reflects the developmental level of executive functions.

Improvement of open innovation processes: case Nokia

Open innovation is becoming increasingly popular in academic literature and in business life, but even if people heard about it, they might not understand what it really is, they may over-estimate it thinking that it is savior or underestimate it, concentrating on limitations and risks. Current work sheds light on most important concepts of open innovation theory. Goal of current research is to offer business processes improvement for both inbound and outbound modes in case company. It is relevant as open innovation proved to affect firms‘ performance in general case and in case company, and Nokia planned to develop open innovation implementation since 2008 but still competitors succeed in it more, therefore analysis of current situation with open innovation in Nokia and recommendations how to improve it are topical. Case study method was used to answer the question ―How open innovation processes can be improved?‖. 11 in-depth interviews with Nokia senior managers and independent consultants were used to reach the goal of the thesis, as well as secondary sources. Results of current work are as-is and to-be models (process models of today and best practices models) of several open innovation modes, and recommendation for case company, which will be presented to company representatives and checked for practical applicability.

Focusing on the quality of learning processes

S. 327-333

Patterns and processes of littoral zooplankton composition in relation to the trophic state of the environment

Avhandlingen handlar om hur kompositionen hos litoralt djurplankton varierar med omgivningens trofiska nivå (m.a.o. eutrofieringsgrad). Arbetets inledande mål är att beskriva hur mängden och artmångfalden hos djurplankton i strandnära vattnen och de omgivande organismsamhällen ändras med närsaltshalter. Huvudsyftet är att utreda allmänna mekanismer som styr dessa mönster och som på så sätt kan vara viktiga i att reglera samhällen även i andra ekologiska system. Undersökningarna gjordes i åländska flador över flera tillväxtsäsonger samt i laboratorier där omgivningsförhållanden i fladorna kunde simuleras och manipuleras. Djurplankton i dessa lagunlika vikar är lägliga modellsystem. Flador är lämpligt avgränsade från det omgivande havet och förekommer allmänt i norra Östersjöregionen. Således kan de inom ett litet område som Åland representera hela regionala gradienten från näringsfattiga till näringsrika förhållanden. De små kräft- och hjuldjuren som djurplankton består av befinner sig i mitten av näringsväven. De sammankopplar olika typer av mikrobiell produktion vidare till högre konsumenter och är på så sätt centrala för organismsamhällens struktur och funktion i nästan alla akvatiska miljöer. I likhet med primärproducenterna (d.v.s. växter och alger som direkt påverkas av närsaltshalterna, och som bl.a. utgör föda och habitat för djurplankton) samvarierar kompositionen hos djurplankton tydligt med omgivningens trofiska nivå tills den blir hög. Sedan börjar hela samhällskompositionen utveckla sig åt två skilda håll. Dessa mönster kan för djurplanktonets del förklaras med att dess komposition ingalunda styrs endast av primärproducenterna, utan av ett komplicerat samspel mellan dessa resurser samt konkurrerande och högre konsumenter (d.v.s. predatorer på flera högre trofinivåer). Detta kom fram speciellt i laboratorieförhållanden då kompositionen hos dessa samhällskomponenter manipulerades. Både deras sammansättning och relativa tätheter i sig, samt en kombination av båda visade sig styra djurplanktonkompositionen. Lokala processer (inom fladorna) och synnerligen förändringar hos olika fundament- (speciellt vass, borstnate och rödsträfse), kärn- (speciellt yngel av a bborre och mört) och nyckelarter (stora predatorer som gädda) verkar kunna avgöra till vilken grad djurplanktonkompositionen samvarierar med omgivningens trofiska nivå. Inte bara samhällen utan också de mekanismer som styr dem ändras med omgivningens trofiska nivå. Flador är ypperliga naturliga laboratorier för att studera dessa och även andra allmänekologiska mönster och mekanismer. De är också oerhört viktiga miljöer för hela kustregionens natur.